IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
As of the commit 1de452a0ed ("regulator: core: Allow drivers to
define their init data as const") we no longer need to do copying of
regulator bulk data from initdata to something dynamic. Let's take
advantage of that.
In addition to saving some code, this also moves us to using
ARRAY_SIZE() to specify how many regulators we have which is less
error prone.
This gets rid of some layers of wrappers which makes it obvious that
we can get rid of an extra error print.
devm_regulator_bulk_get_const() prints errors for you so you don't
need an extra layer of printing.
In all cases here I have preserved the old settings without any
investigation about whether the loads being set are sensible. In the
cases of some of the PHYs if several PHYs in the same file used
exactly the same settings I had them point to the same data structure.
NOTE: Though I haven't done the math, this is likely an overall
savings in terms of "static const" data. We previously always
allocated space for 8 supplies. Each of these supplies took up 36
bytes of data (32 for name, 4 for an int).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496325/
Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 5451781dad ("regulator: core: Only count load for
enabled consumers"), a load isn't counted for a disabled
regulator. That means all the code in the DSI driver to specify and
set loads before disabling a regulator is not actually doing anything
useful. Let's remove it.
It should be noted that all of the loads set that were being specified
were pointless noise anyway. The only use for this number is to pick
between low power and high power modes of regulators. Regulators
appear to do this changeover at loads on the order of 10000 uA. You
would need a lot of clients of the same rail for that 100 uA number to
count for anything.
Note that now that we get rid of the setting of the load at disable
time, we can just set the load once when we first get the regulator
and then forget it.
It should also be noted that the regulator functions
regulator_bulk_enable() and regulator_set_load() already print error
messages when they encounter problems so while moving things around we
get rid of some extra error prints.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496320/
Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Next for v5.20
GPU:
- a619 support
- Fix for unclocked GMU register access
- Devcore dump enhancements
Core:
- client utilization via fdinfo support
- fix fence rollover issue
- gem: Lockdep false-positive warning fix
- gem: Switch to pfn mappings
DPU:
- constification of HW catalog
- support for using encoder as CRC source
- WB support on sc7180
- WB resolution fixes
DP:
- dropped custom bulk clock implementation
- made dp_bridge_mode_valid() return MODE_CLOCK_HIGH where applicable
- fix link retraining on resolution change
MDP5:
- MSM8953 perf data
HDMI:
- YAML'ification of schema
- dropped obsolete GPIO support
- misc cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtuqswBGPw-kCYzJvckK2RR1XTeUEgaXwVG_mvpbv3gPA@mail.gmail.com
There is currently two function for performing reset: dsi_sw_reset and
dsi_sw_reset_restore. Only difference between those is that latter one
assumes that DSI controller is enabled. In contrary former one assumes
that controller is disabled and executed during power-on. However this
assumtion is not true mobile devices which have boot splash set up by
boot-loader.
This patch removes dsi_sw_reset_restore and makes dsi_sw_reset disable
DSI controller during reset sequence if it's enabled.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/489152/
Link: https://lore.kernel.org/r/20220610220259.220622-1-luca@z3ntu.xyz
[DB: fixed the typo in the commit message]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Quoting the header comments, IRQF_ONESHOT is "Used by threaded interrupts
which need to keep the irq line disabled until the threaded handler has
been run.". When applied to an interrupt that doesn't request a threaded
irq then IRQF_ONESHOT has a lesser known (undocumented?) side effect,
which it to disable the forced threading of irqs (and for "normal" kernels
it is a nop). In this case I can find no evidence that suppressing forced
threading is intentional. Had it been intentional then a driver must adopt
the raw_spinlock API in order to avoid deadlocks on PREEMPT_RT kernels
(and avoid calling any kernel API that uses regular spinlocks).
Fix this by removing the spurious additional flag.
This change is required for my Snapdragon 7cx Gen2 tablet to boot-to-GUI
with PREEMPT_RT enabled.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220201174734.196718-2-daniel.thompson@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.
Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.
It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
During board bringups its useful to have a DSI test pattern
generator to isolate a DPU vs a DSI issue and focus on the relevant
hardware block.
To facilitate this, add an API which triggers the DSI controller
test pattern. The expected output is a rectangular checkered pattern.
This has been validated on a single DSI video mode panel by calling it
right after drm_panel_enable() which is also the ideal location to use
this as the DSI host and the panel have been initialized by then.
Further validation on dual DSI and command mode panel is pending.
If there are any fix ups needed for those, it shall be applied on top
of this change.
Changes in v2:
- generate the new dsi.xml.h and update the bitfield names
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/1626922232-29105-2-git-send-email-abhinavk@codeaurora.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Add the msm_disp_snapshot module which adds supports to dump dpu
registers and capture the drm atomic state which can be used in
case of error conditions.
changes in v5:
- start storing disp_state in msm_kms instead of dpu_kms
- get rid of MSM_DISP_SNAPSHOT_IN_* enum by simplifying the functions
- move snprintf inside the snapshot core by using varargs
- get rid of some stale code comments
- allow snapshot module for non-DPU targets
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1618606645-19695-3-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
