IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ata_dev_init_params() fixes:
- Get the "heads" and "sectors" parameters from caller instead of implicitly from dev->id[].
- Return AC_ERR_INVALID instead of 0 if an invalid parameter is found
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Last of the set, just clean up some oddments. Assuming the whole set is
now ok then the remaining differences are the setup of PIO_0 at reset
and the ->data_xfer method.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core
This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.
Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I think this is still needed with the new probe code (which btw seems to
be missing docs in upstream ?).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some CD-ROM drives are slow to clear DRQ, after the last data block
is read by PIO. Use ata_wait_idle() after reading the last data block.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current irq-pio checks ERR bit and stops on ERR before it does anything else.
This behavior doesn't look right.
The DRQ bit should take higher precedence than the ERR bit.
Changes:
- Let the HSM do the data transfer whenever the
device asks for DRQ bit, even if the ERR bit is set.
- For DRQ=1 ERR=1, don't trust the data
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the the in_wq check easier to read as an inline function.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_check_atapi_dma() fix for LLDDs with the ATA_FLAG_PIO_POLLING flag.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup the following unused functions:
- ata_pio_poll()
- ata_pio_complete()
- ata_pio_first_block()
- ata_pio_block()
- ata_pio_error()
ap->pio_task_timeout and other enums.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ata_pio_task() to use the new ata_hsm_move().
Changes:
- refactor ata_pio_task() to poll device status register and
- call the new ata_hsm_move() when device indicates it is not BSY.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Let ata_hsm_move() work with both irq-pio and polling pio codepath.
Changes:
- add a new parameter "in_wq" for polling pio
- add return value "poll_next" to tell polling pio task whether the HSM is finished
- merge code from ata_pio_first_block() to the HSM_ST_FIRST state.
- call ata_poll_qc_complete() if called from the workqueue
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor fix for ata_hsm_move() to work with ata_host_intr().
Changes:
- WARN_ON() and comment fix
- Make the HSM_ST_LAST device status checking more rigid.
- Treat unknown HSM state as BUG().
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move out the irq-pio HSM code from ata_host_intr() to the new ata_hsm_move() function verbatim.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
atapi_packet_task() was replaced by ata_pio_task().
Remove the unused atapi_packet_task().
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix merge problem with upstream.
Changes:
1. add missing dev->cdb_len = 16 for ATA devices
2. use ata_pio_task instead of atapi_packet_task
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add FIXME above ata_dev_xfermask noting that the current
implementation limits all transfer modes to the fastest of the slowest
device on a port which isn't necessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_softreset() should return AC_ERR_* on failure not arbitrary
positive number. While at it, reformat comment above it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
E.D.D. has no user in-tree and mostly useless. Kill it. For possible
out-of-tree users, add a nice warning message and error handling if
LLDD doesn't report any useable reset mechanism (and thus tries to use
E.D.D.).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some of the dependence on the host_set struct
in preparation for supporting SAS HBAs. Adds a struct device
pointer to the ata_port struct.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
drivers/scsi/libata-core.c | 5 +++--
drivers/scsi/libata-scsi.c | 4 ++--
drivers/scsi/scsi_sysfs.c | 2 +-
include/linux/libata.h | 4 ++--
include/scsi/scsi_host.h | 2 +-
5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() responsible for determining whether to take port
or device offline on failure. ata_dev_set_xfermode() and
ata_dev_set_mode() indicate error to the caller instead of disabling
port directly on failure. Also, for consistency, ata_dev_present()
check is done in ata_set_mode() instead of ata_dev_set_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We may or may not disable a device after ata_dev_configure() fails.
Kill 'not supported, ignoring' message in ata_dev_configure() and use
ata_dev_disable() in ata_bus_probe().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements ata_dev_disable() which prints a warning message
and takes @dev offline. Currently, this is done by explicitly
incrementing dev->class with case-by-case warning messages. Giving
user clear indication when libata gives up will be more important as
libata will be doing more retries.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata core is being changed to disallow port/device disable on lower
layers. However, some LLDDs (sata_mv) directly disable port on
command failure. This patch makes ata_exec_internal() check whether a
port got disabled after an internal command. If it is, AC_ERR_SYSTEM
is added to err_mask and the port gets re-enabled.
As internal command failure results in device disable for drivers
which don't implement newer reset/EH callbacks, this change results in
no behavior change for single device per port controllers. For
slave-possible LLDDs which disable port on command failure, (1) such
drivers don't exist currently, (2) issuing command to the other device
of once-disabled port shouldn't result in catastrophe even if such
driver exists. So, this should be enough as a temporary measure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that each ata_device has xfer masks, per-dev limits can be made
per-dev instead of per-port. Make per-dev limits per-dev.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add per-dev pio/mwdma/udma_mask. All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port. This change will also benefit later EH speed down
and hotplug.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."
I fixed this by adding a check for zero. While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
