IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some comments refer to 80211.o or similar; also remove
a comment about implementing fragments better, we really
have better things to do.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the scan functions are called ieee80211_sta_scan_*
or similar, make clean it up so they are all just called
ieee80211_scan_*.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bridge_packets configuration really should be per virtual
interface (theoretically per AP/VLAN, but this is much easier);
there currently is no way to set it yet though. Also invert
the option to "NO_BRIDGE_PACKETS" so the default is to bridge.
While at it, also document the flags properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It really doesn't belong into the wireless extensions code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This way all the utility functions are at the top, then the
state machine and externally callable functions are moved to
the bottom. Also clean up ieee80211_i.h a bit and add a few
comments about which functions are called from where.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits off mesh handling from the STA/IBSS.
Unfortunately it increases mesh code size a bit, but I
think it makes things clearer. The patch also reduces
per-interface run-time memory usage.
Also clean up a few places where ifdef is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_sta_tx function isn't MLME code any more,
it's getting used by a lot of code. Move it to utils and
rename it to ieee80211_tx_skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like the HT code, this doesn't depend on the STA-mode implementation
and can be handled entirely independently. There's only stub code
for now, but when it gets filled having it in its own file will be
beneficial.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation handling isn't dependent on anything related to our
STA-mode implementation, and doesn't need to depend on it for frame
processing. This patch moves the relevant code to ht.c and adds a
hook in rx.c. For now, the relevant action frames are only processed
in STA/IBSS modes, but that's now something we can easily change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware is started it might be in a confused state with
respect to queue QoS parameters. This patch changes mac80211
to set sane defaults right after the hardware is brought up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves all the BSS list handling out of mlme.c to scan.c,
no further changes except fixing kzalloc/atomic_inc/atomic_inc
to kzalloc/atomic_set(2).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors some code and moves the scan RX function
to scan.c. More importantly, however, it changes it so that the
MLME's beacon/probe_resp functions aren't invoked when scanning
so that we can remove a "if (scanning)" conditions from two
places.
There's a very slight behavioural change in this patch: now,
when scanning, IBSS and mesh aren't updated even on the same
channel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here's a first patch to move some code from mlme.c to a
new file called scan.c. The end result will hopefully be
a more manageable mlme.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now use sdata pointers most of the time, using a netdev
pointer here is somewhat artificial, use an sdata pointer instead.
Replace a netdev-prefix in a few messages by a wiphy-prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs union in struct ieee80211_sub_if_data is misused by including a
common default_key dentry as a union member. This ends occupying the same
memory area with the first dentry in other union members (structures;
usually drop_unencrypted). Consequently, debugfs operations on
default_key symlinks and drop_unencrypted entry are using the same
dentry pointer even though they are supposed to be separate ones. This
can lead to removing entries incorrectly or potentially leaving
something behind since one of the dentry pointers gets lost.
Fix this by moving the default_key dentry to a new struct
(common_debugfs) that contains dentries (more to be added in future)
that are shared by all vif types. The debugfs union must only be used
for vif type-specific entries to avoid this type of pointer corruption.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up and extend scan result processing by storing all the IEs from
Beacon/Probe Response frames in a single block instead of allocating
memory for each specific IE separately. This removes lot of unnecessary
code and automatically supports reporting of new IEs (e.g., IEEE
802.11r) into user space without need to manually extend mac80211
scanning code whenever a new protocol adds IE(s).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous version was using incorrect union structures for non-AP
interfaces when adding and removing max_ratectrl_rateidx and
force_unicast_rateidx entries. Depending on the vif type, this ended
up in corrupting debugfs entries since the dentries inside different
union structures ended up going being on top of eachother.. As the
end result, debugfs files were being left behind with references to
freed data (instant kernel oops on access) and directories were not
removed properly when unloading mac80211 drivers. This patch fixes
those issues by using only a single union structure based on the vif
type.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a direct probe request as first step in the association
flow if data we have is not up to date. Motivation of this step is to make
sure that the bss information we have is correct, since last scan could
have been done a while ago, and beacons do not fully answer this need as
there are potential differences between them and probe responses (e.g.
WMM parameter element)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes noticed problem in noisy environments of 50+ APs
that scan fails to find the requested AP on first try, which
leads to connection refusal. second scan has empirically proven to fix
this problem in almost all cases.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch move add STA_MLME to station mlme state defines.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.
It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.
If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.
This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ETH_P_PAE belongs in if_ether.h with the other ETH_P_* definitions. This
patch moves it there.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the dtim_period in ieee80211_bss_conf, this allows the low
level driver to know the dtim_period, and to plan power save accordingly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make mac80211 transmit correctly fragmented packet after
queue was stopped
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only behavior change is that we do not drop packets under any
circumstances. If that is absolutely needed, we could easily add it
back.
With cleanups and help from Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch pushes the "netif_running()" and "same type as before"
checks down into ieee80211_if_change_type() to centralise the
logic instead of duplicating it for cfg80211 and wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps the virtual interface handling and makes the
code much easier to follow. Fewer functions, better names, less
spaghetti code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)
Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.
This patch changes the master netdev to be special, it now
- no longer is on the list of virtual interfaces, which
lets me remove a lot of tests for that
- no longer has sub_if_data attached, since that isn't used
Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes call of ieee80211_bss_info_change_notify from within
ieee80211_reset_erp_info. This allows gathering all bss info changes
into one call to the driver in the disassociation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds block ack request capability
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reworks the mac80211 debug settings making them more focused
and adding help text for those that didn't have one. It also removes a
number of printks that can be triggered remotely and add no value, e.g.
"too short deauthentication frame received - ignoring".
If somebody really needs to debug that they should just add a monitor
interface and look at the frames in wireshark.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the TX path to no longer use function pointers for
TX handlers but rather invoke them directly. If debugging is
enabled, mark the TX handlers noinline because otherwise they
all get inlined into invoke_tx_handlers() which makes it harder
to see where a bug is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces parsing of 11h and 11d related elements from incoming
management frames.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three major portions to this change:
1) Add IW_EV_COMPAT_LCP_LEN, IW_EV_COMPAT_POINT_OFF,
and IW_EV_COMPAT_POINT_LEN helper defines.
2) Delete iw_stream_check_add_*(), they are unused.
3) Add iw_request_info argument to iwe_stream_add_*(), and use it to
size the event and pointer lengths correctly depending upon whether
IW_REQUEST_FLAG_COMPAT is set or not.
4) The mechanical transformations to the drivers and wireless stack
bits to get the iw_request_info passed down into the routines
modified in #3. Also, explicit references to IW_EV_LCP_LEN are
replaced with iwe_stream_lcp_len(info).
With a lot of help and bug fixes from Masakazu Mokuno.
Signed-off-by: David S. Miller <davem@davemloft.net>
In IBSS mode prior to join/creation of new IBSS it is possible that
a frame from unknown station is received and an ibss_add_sta() is
called. This will cause a warning in rate_lowest_index() since the
list of supported rates of our station is not initialized yet.
The fix is to add ibss stations with a rate we received that frame
at; this single-element set will be extended later based on beacon
data. Also there is no need to store stations from a foreign IBSS.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check to the set_channel flow. When attempting to change
the channel while in IBSS mode, and the new channel does not support IBSS
mode, the flow return with an error value with no consequences on the
mac80211 and driver state.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows to disable FAT channel in specific configurations.
For example the configuration (8, +1), (primary channel 8, extension
channel 12) isn't permitted in U.S., but (8, -1), (primary channel 8,
extension channel 4) is. When FAT channel configuration is not
permitted, FAT channel should be reported as not supported in the
capabilities of the HT IE in association request. And sssociation is
performed on 20Mhz channel.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The useless channel use statistics are quite a lot of code, currently
use integer divisions in the packet fast path, are rather inaccurate
since they do not account for retries and finally nobody even cares.
Hence, remove them completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mac80211 and drivers to be multi-queue aware and
use that instead of the internal queue mapping. Also does a number
of cleanups in various pieces of the code that fall out and reduces
internal mac80211 state size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no reason for a driver to reject a frame on
an A-MPDU queue when it can stop that queue for any period
of time and is given frames one by one. Hence, disallow it
with a big warning and reduce mac80211-internal state.
Also add a warning when we try to fragment a frame destined
for an A-MPDU queue and drop it, the actual bug needs to be
fixed elsewhere but I'm not exactly sure how to yet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 31ccc476b77234f6afb3 (mac80211: QoS related cleanups) I
accidentally changed these to use IEEE80211_MAX_AMPDU_QUEUES twice
which obviously is wrong, it should be IEEE80211_MAX_QUEUES once.
Currently harmless as they're both the same value anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_rx_agg_session_timer_expired() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has some code cleanups (some inspired by checkpatch), I got
bored at probably a third of the output though so if somebody
else wants to...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reworks the scanning code (ieee80211_rx_bss_info) to take
more parameters from beacons and keep a BSS info structure alive when
only beacons for it are received. This fixes a problem with iwlwifi
drivers (where we don't understand the root cause of the problem yet)
and another driver for some broken hardware (which cannot send probe
requests unless associated, so can't always actively scan.)
Signed-off-by: Bill Moss <bmoss@clemson.edu>
[jmberg: reformatted comments, make probe_resp a bool]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When STAs are expired, we need to hold the sta_lock. Using
the same lock for keys too would then mean we'd need another
key free function, and that'll just lead to confusion, so just
use a new spinlock for all key lists.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames all mac80211 files (except ieee80211_i.h) to get rid
of the useless ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Up to now, key manipulation is supposed to run under RTNL to
avoid concurrent manipulations and also allow the set_key()
hardware callback to sleep. This is not feasible because STA
structs are rcu-protected and thus a lot of operations there
cannot take the RTNL. Also, key references are rcu-protected
so we cannot do things atomically.
This patch changes key locking completely:
* key operations are now atomic
* hardware crypto offload is enabled and disabled from
a workqueue, due to that key freeing is also delayed
* debugfs code is also run from a workqueue
* keys reference STAs (and vice versa!) so during STA
unlink the STAs key reference is removed but not the
keys STA reference, to avoid races key todo work is
run before STA destruction.
* fewer STA operations now need the RTNL which was
required due to key operations
This fixes the locking problems lockdep pointed out and also
makes things more light-weight because the rtnl isn't required
as much.
Note that the key todo lock/key mutex are global locks, this
is not required, of course, they could be per-hardware instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Really doesn't need to be defined four times.
Also, while at it, remove a useless macro (IEEE80211_ALIGN32_PAD)
and a function prototype for a function we don't actually have
(ieee80211_set_compression.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch eliminates the use of conf_ht, replacing it with
bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 6c4711b469.
That patch breaks mesh config comparison between beacons/probe reponses, so
every beacon from a mesh network would be added as a new bss. Since the
comparison has to be performed for every received beacon I believe it is best to
save the mesh config in a format easy to compare, rather than do a bunch of
unaligned accesses to compare field by field.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows cleaner code when accesing bss->mesh_config components.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the IBSS code tries to flush the STA list, it does so in
an atomic context. Flushing isn't safe there, however, and
requires the RTNL, so we need to defer it to a workqueue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reorders some fields in various structures to have
less padding within the structures, making them smaller. It
doesn't yet make any type adjustments, but often size_t is used
for example for IE lengths which is total overkill since size_t
will be 8 bytes long on 64-bit yet the length can at most fill
a u8.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a clean tear down for all block ack sessions if interface
goes down or if a deauthentication is done.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we take down an interface, we need to remove the STA info
items that belong to it because otherwise we might invoke a
sta_notify() callback in the driver when we later delete the
STA entries, but in that case the driver will already have
removed its knowledge of the interface they belonged to leading
to confusion. Also, we could invoke the set_tim() callback after
the driver removed its knowledge of the interface, which can
lead to a crash if it requests a beacon with a then-invalid vif
pointer!
A side effect of this patch is that, because it was easier, it
disallows changing the WDS peer while an interface is up. Should
that actually be necessary, it can be added back, but the WDS
peer STA entry may not be added while the interface is UP so for
now I've simplified the WDS peer's STA entry lifetime management.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split it into ieee80211_tx_data and ieee80211_rx_data to clarify
usage/flag usage and remove the stupid union thing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Includes integration in struct sta_info of mesh peer link elements, previously
on their own mesh peer link table.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This consolidates all TIM handling code to avoid re-introducing
errors with the bitmap/set_tim order and to reduce code. While
reading the code I noticed a possible problem so I also added
a comment about that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds "cooked" monitor mode to mac80211. A monitor interface
in "cooked" mode will see all frames that mac80211 has not used
internally.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't really make sense to have extra pointers to the RX/TX
handler arrays instead of just using the arrays directly, that
also allows us to make them static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of the monitor configuration flags now provided by cfg80211.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some instances of RX_DROP mean that the frame was useless,
others mean that the frame should be visible in userspace
on "cooked" monitor interfaces. This patch splits up RX_DROP
and changes each instance appropriately.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The _DROP result will need to be split in the RX path but not
in the TX path, so for preparation split up the type into two
types, one for RX and one for TX. Also make sure (via sparse)
that they cannot be confused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the 802.1X port acess control enable flag
since it is not required. Instead, set the authorized flag for
each station that we normally communicate with (WDS peers, IBSS
peers and APs we're associated to) and require hostapd to set
the authorized flag for all stations when port control is not
enabled.
Also, since I was working in that area, this documents station
flags and removes the unused "permanent" one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These handlers do not really return a status and the compiler
can do a much better job when they're simply static functions
that it can inline if appropriate. Also makes the code shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows qdisc support in A-MPDU Tx. a method to
handle QoS <-> TID switches is present in this patch.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the cfg80211 hooks for configuring beaconing
on an access point interface in mac80211. While doing so, it fixes
a number of races that could badly crash the machine when the
beacon is changed while being requested by the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have a seperate LED which indicates if the radio is
enabled or not. This adds a LED trigger to mac80211 where drivers
can hook into when they are interested in radio status changes.
v2: Check hw.conf.radio_enabled when calling start().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to handle Block Ack Request
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the basic needed abilities and functions for A-MPDU Rx session
changed functions:
- ieee80211_sta_process_addba_request - Rx A-MPDU initialization enabled
- ieee80211_stop - stops all A-MPDU Rx in case interface goes down
added functions:
- ieee80211_send_delba - used for sending out Del BA in A-MPDU sessions
- ieee80211_sta_stop_rx_BA_session - stopping Rx A-MPDU session
- sta_rx_agg_session_timer_expired - stops A-MPDU Rx use if load is too
low
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch left only one user of the ieee80211_is_eapol()
function and that user can be eliminated easily by introducing
a new "frame is EAPOL" flag to handle the frame specially (we
already have this information) instead of doing the (expensive)
ieee80211_is_eapol() all the time.
Also, allow unencrypted frames to be sent when they are injected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the eapol frame handling and some related code in the
receive and transmit paths. After this patch
* EAPOL frames addressed to us or the EAPOL group address are
always accepted regardless of whether they are encrypted or not
* other frames from a station are dropped if PAE is enabled and
the station is not authorized
* unencrypted frames (except the EAPOL frames above) are dropped if
drop_unencrypted is enabled
* some superfluous code that eth_type_trans handles anyway is gone
* port control is done for transmitted packets
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves u8 amsdu_frame in ieee80211_txrx_data to the flags
section as IEEE80211_TXRXD_RX_AMSDU
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures the 802.11n mode of operation
internally in ieee80211_conf structure and in the low-level
driver as well (through op conf_ht).
It does not include AP configuration flows.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to receive and handle A-MSDU frames.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch presents the ability to parse and compose HT IEs, and to put
the IE relevant data inside the mac80211's internal HT structures
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the Rx handlers chain by incorporating previously
handlers ieee80211_rx_h_802_1x_pae and ieee80211_rx_h_drop_unencrypted
into ieee80211_rx_h_data, already in 802.3 form. this scheme follows more
precisely after the IEEE802.11 data plane archituecture, and will prevent
code duplication to IEEE8021.11n A-MSDU handler.
added function:
- ieee80211_data_to_8023: transfering 802.11 data frames to 802.3 frame
- ieee80211_deliver_skb: delivering the 802.3 frames to upper stack
eliminated handlers:
- ieee80211_rx_h_drop_unencrypted: now function ieee80211_drop_unencrypted
- ieee80211_rx_h_802_1x_pae: now function ieee80211_802_1x_pae
changed handlers:
- ieee80211_rx_h_data: now contains calls to four above function
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scan code in mac80211 makes the software scan assumption in various
places. For example, we stop the Tx queue during a software scan so that
all the Tx packets will be queued by the stack. We also drop frames not
related to scan in the software scan process. But these are not true for
hardware scan.
Some wireless hardwares (for example iwl3945/4965) has the ability to
perform the whole scan process by hardware and/or firmware. The hardware
scan is relative powerful in that it tries to maintain normal network
traffic while doing a scan in the background. Some drivers (i.e iwlwifi)
do provide a way to tune the hardware scan parameters (for example if the
STA is associated, what's the max time could the STA leave from the
associated channel, how long the scans get suspended after returning to
the service channel, etc). But basically this is transparent to the
stack. mac80211 should not stop Tx queues or drop Rx packets during a
hardware scan.
This patch resolves the above problem by spliting the current scan
indicator local->sta_scanning into local->sta_sw_scanning and
local->sta_hw_scanning. It then changes the scan related code to be aware
of hardware scan or software scan in various places. With this patch,
iwlwifi performs much better in the scan-while-associated condition and
disable_hw_scan=1 should never be required.
Cc: Mohamed Abbas <mohamed.abbas@intel.com>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all references to local->scan_flags as these are not
used anymore since the removal of prism2 ioctls.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes scanning for specific ssid's which is broken due to the
scan being queued up without respecting the ssid to scan for.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the long bug-hunt for why dynamic WEP networks didn't work it
turned out that mac80211 incorrectly uses IW_AUTH_KEY_MGMT while
it should use IW_AUTH_PRIVACY_INVOKED to determine whether to
associate to protected networks or not.
This patch changes the behaviour to be that way and clarifies the
existing code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many devices have LEDs to indicate the link status.
Export this functionality to drivers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves radiotap injection by removing the shortcut over TX handlers
that led to BUGS when injecting frames without setting a rate and also
resulted in various other quirks. Now, TX handlers are run but some
information that was present in the radiotap header is used instead of
automatic settings.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Andy Green <andy@warmcat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removes the management interface since it is only required
for hostapd/userspace MLME, will not be in the final tree
at least in this form and hostapd/userspace MLME currently
do not work against this tree anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use bitwise NOT.
This also cleans up the code a little bit to make it more readable.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not useful since we do not support probe response
offload to hardware at this time and beacons are set in
another way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all prism2 ioctls.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we update the counters iff_promiscs and iff_allmultis
in struct ieee80211_local we have no common lock held to
protect them. The problem is that the update to each counter
may not be atomic, so we could end up with iff_promiscs == -1
in unfortunate conditions. To fix it, use atomic_t values.
It doesn't matter whether the two counters are updated
together atomically or not, if there are two invocations
of set_multicast_list we will end up with multiple
configure_filter() invocations of which the latter will always
be correct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TKIP IV should be updated only after MMIC verification,
this patch changes it to be at that spot.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
VLAN interfaces have yet another bug: they aren't accounted
for properly in the receive path in prepare_for_handlers().
I noticed this by code inspection, but it would be easy for
the compiler to catch such things if we'd just use the proper
enum where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Florian Lohoff noticed a bug in mac80211: when bringing the
master interface down while other virtual interfaces are up
we call dev_close() under a spinlock which is not allowed.
This patch removes the sub_if_lock used by mac80211 in favour
of using an RCU list. All list manipulations are already done
under rtnl so are well protected against each other, and the
read-side locks we took in the RX and TX code are already in
RCU read-side critical sections.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Florian Lohoff <flo@rfc822.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to verify that VLAN interfaces
are valid and not bother drivers about them any more.
VLAN interfaces are now only valid when an AP interface
is up with the same MAC address, and are automatically
turned off when the AP interface is set down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the key threshold stuff from mac80211.
I have patches for later that add it as a per-key setting
to nl/cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats are now available for device usage inside network_device
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves all the key handling code out from ieee80211_ioctl.c
into key.c and also does the following changes including documentation
updates in mac80211.h:
1) Turn off hardware acceleration for keys when the interface
is down. This is necessary because otherwise monitor
interfaces could be decrypting frames for other interfaces
that are down at the moment. Also, it should go some way
towards better suspend/resume support, in any case the
routines used here could be used for that as well.
Additionally, this makes the driver interface nicer, keys
for a specific local MAC address are only ever present
while an interface with that MAC address is enabled.
2) Change driver set_key() callback interface to allow only
return values of -ENOSPC, -EOPNOTSUPP and 0, warn on all
other return values. This allows debugging the stack when
a driver notices it's handed a key while it is down.
3) Invert the flag meaning to KEY_FLAG_UPLOADED_TO_HARDWARE.
4) Remove REMOVE_ALL_KEYS command as it isn't used nor do we
want to use it, we'll use DISABLE_KEY for each key. It is
hard to use REMOVE_ALL_KEYS because we can handle multiple
virtual interfaces with different key configuration, so we'd
have to keep track of a lot of state for this and that isn't
worth it.
5) Warn when disabling a key fails, it musn't.
6) Remove IEEE80211_HW_NO_TKIP_WMM_HWACCEL in favour of per-key
IEEE80211_KEY_FLAG_WMM_STA to let driver sort it out itself.
7) Tell driver that a (non-WEP) key is used only for transmission
by using an all-zeroes station MAC address when configuring.
8) Change the set_key() callback to have access to the local MAC
address the key is being added for.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the default_wep_only stuff, this wasn't really done well
and no current driver actually cares.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch embeds the struct ieee80211_key_conf into struct ieee80211_key
and thus avoids allocations and having data present twice.
This required some more changes:
1) The removal of the IEEE80211_KEY_DEFAULT_TX_KEY key flag.
This flag isn't used by drivers nor should it be since
we have a set_key_idx() callback. Maybe that callback needs
to be extended to include the key conf, but only a driver that
requires it will tell.
2) The removal of the IEEE80211_KEY_DEFAULT_WEP_ONLY key flag.
This flag is global, so it shouldn't be passed in the key
conf structure. Pass it to the function instead.
Also, this patch removes the AID parameter to the set_key() callback
because it is currently unused and the hardware currently cannot know
about the AID anyway. I suspect this was used with some hardware that
actually selected the AID itself, but that functionality was removed.
Additionally, I've removed the ALG_NULL key algorithm since we have
ALG_NONE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_sub_if_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_if_sta
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_txrx_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove bitfields from struct ieee80211_tx_packet_data
[Johannes: completely clear flags in ieee80211_remove_tx_extra]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new file event.c that will contain code to send mac/mlme
events to userspace. For now put the Michael MIC failure condition
into it and remove sending of that condition via the management
interface, hostapd interestingly doesn't do anything when it gets
such a packet besides printing a message, it reacts only on the
private iwevent.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The key_mgmt variable for STA interfaces doesn't seem well-defined
nor do we actually use the values other than "NONE", so change it to
be named better.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_RADAR_DETECT
* PRISM2_PARAM_SPECTRUM_MGMT
are not used by hostapd or wpa_supplicant,
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_STA_ANTENNA_SEL
* PRISM2_PARAM_TX_POWER_REDUCTION
* PRISM2_PARAM_DEFAULT_WEP_ONLY
are not used by hostapd or wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_ANTENNA_MODE
* PRISM2_PARAM_STAT_TIME
are not used by hostapd or wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1211rw and bcm43xx are interested in being notified when ERP IE conditions
change, so that they can reprogram a register which affects how control frames
are transmitted.
This patch adds an interface similar to the one that can be found in softmac.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similarly to CTS protection, whether short preambles are used for 802.11b
transmissions should be a per-subif setting, not device global.
For STAs, this patch makes short preamble handling automatic based on the ERP
IE. For APs, hostapd still uses the prism ioctls, but the write ioctl has been
restricted to AP-only subifs.
ieee80211_txrx_data.short_preamble (an unused field) was removed.
Unfortunately, some API changes were required for the following functions:
- ieee80211_generic_frame_duration
- ieee80211_rts_duration
- ieee80211_ctstoself_duration
- ieee80211_rts_get
- ieee80211_ctstoself_get
Affected drivers were updated accordingly.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_info code has some awkward locking which prevents some driver
callbacks from being allowed to sleep. This patch makes the locking more
focused so code that calls driver callbacks are allowed to sleep. It also
converts sta_lock to a rwlock.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new file util.c and move a whole bunch of functions into it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I think these can go with rate control just as well and it makes
ieee80211.c more readable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
into a new file key.c which doesn't have much code right now but
it makes ieee80211.c easier to read.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, a function misnamed ieee80211_init_client() is used to handle
regulatory domain control. It is called from
ieee80211_register_hwmode(), which typically runs 2 or 3 times
(802.11a/b/g), but each time it iterates over all the modes.
This patch cleans this up and removes the confusion:
ieee80211_init_client was effectively renamed to
ieee80211_set_default_regdomain and is now run on a per-mode basis
(doesn't have to deal with netdevs). I also moved the regdomain handling
code into its own file and added some documentation.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, CTS protection is partially implemented twice:
1. via prism2 ioctls, only used by hostapd
2. via STA beacon parsing, recorded in sta.use_protection but never used
(other than printed in debugfs)
Protection control should be implemented on a per-subif basis. For example,
a single physical device may be running a soft AP on one channel, and a STA
on another. The AP interface should use protection based on what hostapd told
it, and the STA interface should use protection based on beacon parsing.
These should operate independantly: one subif using protection should not
influence the other.
To implement this, I moved the use_protection flag into ieee80211_sub_if_data
and removed the device-global cts_protect_erp_frames flag.
I also made the PRISM2_PARAM_CTS_PROTECT_ERP_FRAMES write operation only
available for AP interfaces, to avoid any possibility of the user messing with
the behaviour of a STA.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "protection needed" flag is currently parsed out of the ERP IE in
beacons. This patch allows the ERP IE to be available at assocation time
and causes the appropriate actions to be performed earlier.
It is slightly complicated by the fact that most APs don't include the
ERP IE in association responses. To work around this, we store ERP
values in the ieee80211_sta_bss structure.
Also added some WLAN_ERP defines for use by upcoming patches.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These aren't used anywhere (hostapd, wpa_supplicant) and until we
have a proper interface to the rate control algorithms they don't
make much sense either since e.g. rc80211_lowest won't honour them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch separates the monitor interface start_xmit from the
subif start xmit (those other devices have 802.3 framing, monitor
interfaces have radiotap framing)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 show transmitted frames on monitor interfaces,
including radiotap headers that indicate some transmission parameters.
The shown parameters will need to be expanded, but this should work as
a basis to work from.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export various mac80211 internal variables through debugfs.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
