IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Commit af46800 ("ASoC: Implement mux control sharing") revealed that
"Left Line1[L | R] Mux" and "Right Line1[L | R] Mux" widgets were pointing
to the same kcontrols and codec registers and thus soc-core falsely detected
them as shared controls. This is actually wrong since there are separate
registers in hardware that configure Line1L to RADC and Line1R to LADC cross
connects so these muxes should not be shared.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Enable ramp down/up step to be configured based on
platform.
Signed-off-by: Axel Castaneda Gonzalez <x0055901@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set default sysclk constraints to high performance mode.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove dependency between pll (hppll, lppll) and headset power
mode (low-power, high-performance), as headset power mode can
be used with any pll.
A new control is created to allow headset power mode configuration
from userspace. Changing headset power mode during earpiece related
usecases is not propagated down to the codec as earpiece requires
HS DAC in HP mode.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add other supported sample rates to LP and HP modes.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add all DAIs to fully support OMAP4 ABE.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert TWL6040 CODEC driver into a TWL6040 MFD child, it implies
that MFD-level operations like register accesses, clock setting
and power management are done through MFD APIs, not directly by
CODEC driver anymore. To avoid conflicts with the other MFD child,
vibrator registers are skipped in CODEC driver.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This delay is very conservative.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
The clock needed by the I2S driver is associated with the I2S device name
in the standard fashion. Hence, use clk_get(dev) instead of clk_get_sys(clk_name).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The I2S controller needs a clock to respond to register writes. Without
this, register writes will at worst hang the CPU. In practice, I've only
observed writes being dropped.
Luckily, the dropped register writes historically had no effect:
TEGRA_I2S_TIMING: The value we wrote was the reset default.
TEGRA_I2S_FIFO_SCR: The default was for the FIFOs to request more data
when one slot was empty. The requested value was for the FIFOs to request
when four slots were empty. The DMA controller in the mainline kernel is
configured to burst a single entry at a time into the FIFO, hence there
was no issue. The only negative effect was on bus efficiency losses due
to an increased number of arbitration attempts.
However, in various non-upstream changes, the DMA controller now bursts
four entries at a time into the FIFO. If there is only space for one
entry, the data is simply dropped. In practice, this resulted in 3/4 of
samples being dropped, and playback at 4x the expected rate and pitch.
By fixing the clocking issue, this is solved.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Since we now route the front DAC via aa-mix widget, adding the aa-mix
to surrounds will result in a mix-up of both front and surround PCM
signals. For avoiding this, the aa-mix routes have to be disabled
for surround paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the individual DAC is available for the headphone output, the driver
should create the DAC for its volume control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT1718S, the multi-channel path should be like following:
DAC 0-->Mixer 9(index 5)-->Mixer 0(index 1)-->Front Pin;
DAC 1-->Mixer 1(index 0)-->Surround Pin;
DAC 2-->C/LFE Pin;
DAC 3-->Mixer 2(index 0)-->Side Pin;
But current code built Surround and Side path through index 1 of
Mixer 1 and 2. So Adjusting Surround and Side channel amplifier is
invalid. This patch fixes the issue.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT1718S, Mixer 9 doesn't expose the connection to DAC 0. So when
building up a 'PCM Playback' amplifier control, it will fail since
getting DAC 0 index of Mixer 9 returned -1. So I added a dac_mixer_idx
to indicated the actual index of DAC 0 to Mixer 9. Following is the
patch and next mail is another.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation for ASoC dynamic PCM support (AKA ASoC DSP)
Platform will also support DAPM so separate out the probe function
to simplify the code (just like the codec probe).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unmute DAC on front speaker path when Independent HP is enabled.
When to enable Independent HP, the front speaker won't output any sound
for VT1708, VT1708B, VT1708S and VT1702.
I find the via_independent_hp_put() routine will mute DAC 0 path in Mixer 0.
For these codecs, when using Independent HP, there could have two
independent streams, one is from DAC0-->Mixer0-->Front Pin, the other is
from DAC3-->GainSW3-->Side Pin.
So I added a check for DAC-->Mixer path in activate_output_path().
If current path is DAC-->Mixer, no need to mute DAC index in Mixer.
In fact, to change connection of Headphone pin or Mux connected with HP
is enough.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the re-implementation of Independent-HP mode in the
case where the DAC is shared between HP and side-channel streams.
Now the driver tries to parse the output-path using the pre-parsed
side-channel DAC for the independent HP output, too.
When a playback PCM stream is opened with this shared mode, the
Independent-HP mixer switch can't be changed for avoiding the conflict,
thus it returns -EBUSY error.
One remaining unintuitive issue is that the DAC volume is still
controlled as "Side" volume although it's shared by both independent-HP
and side streams.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The char can be unsigned on some architectures. Since the code checks
the negative values, they should be declared as signed char explicitly.
sound/pci/rme9652/hdspm.c:5449: warning: comparison is always false due to limited range of data type
sound/pci/rme9652/hdspm.c:5462: warning: comparison is always false due to limited range of data type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the wrongly converted short values:
sound/pci/cs5535audio/cs5535audio_pcm.c:152: warning: large integer implicitly truncated to unsigned type
sound/pci/cs5535audio/cs5535audio_pcm.c:160: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More for neatness than any actual performance improvement.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It was consistently wrong for everything except WM8993 so should be no
functional change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.comm>
The Blackfin DMA controller can report one frame beyond the end of the
buffer in the wraparound case but ALSA requires that the pointer always
be in the buffer. Do the wraparound to handle this. A similar bug is
likely to apply to the other Blackfin PCM drivers but the code is less
obvious to inspection and I don't have a user to test.
Reported-by: Kieran O'Leary <Kieran.O'Leary@wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I noticed that the last character of the ELD monitor name is lost,
this fixes the issue.
This fix should be confirming to the HDA spec, and works together with
the DRM part of the ELD patch.
The HDA spec does not mention that Monitor_Name_String is an '\0'
ending string, and it allows NML to be 1, which is only valid when MNL
does not count the possible ending '\0'.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move codec init verb which is only applicatable for VT1708.
I've found the root cause that jack plugged in can't be detected.
The verb in vt1708_init_verbs is used to power down jack detect circuit.
This verb is only applicable to VT1708. vt1708 didn't implement jack
detect function in hardware, so we should shut down this function to
avoid noise. But for other codecs, hardware implement jack detect
function. If sending this verb during initialization, jack detect will
be invalid. So I move this verb from via_parse_auto_config() to
patch_vt1708().
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create snd_hda_get_conn_index() helper function for obtaining the
connection index of the widget. Replaced the similar codes used in
several codec-drivers with this common helper.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a issue to enable unsolicited response to line-out pins.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a machine driver to support the EVAL-ADAV801 and EVAL-ADAV803 boards
connected to a Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch updates the email address of the sound drivers supported by me to an
email account I will use on a more regular basis in the future.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we're not using the new auto parser as a fallback yet,
add it manually as a quirk.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant ID 506c was found on Acer Aspire 3830TG. As users report
no playback, sending to stable should be safe.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/783582
Reported-by: andROOM
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use static inline for dummy function to fix the warnings like below
sound/pci/hda/patch_sigmatel.c: In function ‘stac92xx_init’:
sound/pci/hda/patch_sigmatel.c:4387:3: warning: statement with no effect
sound/pci/hda/patch_sigmatel.c: In function ‘stac92xx_resume’:
sound/pci/hda/patch_sigmatel.c:4927:3: warning: statement with no effect
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More similar fixes like previous commits: handle the exceptional case
like ALC267 where no volume amp is found in ADC widget but in the
capsrc widget instead.
Also minor checks for avoiding possible erros: no connection-select
when the pin has a single selection, and add beep verbs only when the
0x1d is used for beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC259 seems to provide an invalid widget capability for the input-src
selector widget. The widget shows the input-amp while it's a selector,
and this confuses the current ALC882 initialization code that is used
for ALC259, too. For fixing this, check the amp capability and handle
the connection selection individually.
Also, ALC259 has no mute bit in DAC volume, so we need to initialize
it as ZERO instead of MUTE.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269 and compatible codecs have the output volume in DACs, thus we
can't use the ALC880's code as is. Fixed by checking the amp caps and
picking up the right widget for initialization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Look through the known NIDs that may have EAPD capabilities and turn
on/off them appropriately instead of checking the individual vendor ids.
This will also avoid the forgotten entries of newly added codec ids
in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the regression introduced by the commit
1f0f4b8036b1fe1347cb4f1f199601b87de9be46
ALSA: hda - Reduce static init verbs for Realtek auto-parsers
The input amps of mixer widgets should be unmuted as default (as
usually they have no assigned mixer switches).
More fixes in this commit are, however, for ALC260: ALC260 codec can
have multiple output mixers connnected to a single DAC althouh the
driver didn't pick up them properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Realtek codecs have the output pins hardwired with certain DACs.
These DACs have to be assigned at first and assign the rest for
multi-DAC pins so that all DACs can be assigned properly.
Without such an optimization, speaker outputs may be assigned to the
same DAC as the headphone or others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
