IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
BATADV_CMD_GET_ROUTING_ALGOS is used to get the list of supported routing
algorithms.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Reduce the number of changes to
BATADV_CMD_GET_ROUTING_ALGOS, fix includes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The bat_algo.h had some functions declared which were not part of the
bat_algo.c file. These are instead stored in bat_v.c and bat_iv_ogm.c. The
declaration should therefore be also in bat_v.h and bat_iv_ogm,h to make
them easier to find.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bat_algo functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~15%, 103
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ELP interval and throughput override interface settings are initialized
with default settings on every time an interface is added to a mesh.
This patch prevents this behavior by moving the configuration init to the
interface detection routine which runs only once per interface.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[a@unstable.cc: move initialization to batadv_v_hardif_init]
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This is the initial implementation of the new OGM protocol
(version 2). It has been designed to work on top of the
newly added ELP.
In the previous version the OGM protocol was used to both
measure link qualities and flood the network with the metric
information. In this version the protocol is in charge of
the latter task only, leaving the former to ELP.
This means being able to decouple the interval used by the
neighbor discovery from the OGM broadcasting, which revealed
to be costly in dense networks and needed to be relaxed so
leading to a less responsive routing protocol.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The B.A.T.M.A.N. protocol originally only used a single
message type (called OGM) to determine the link qualities to
the direct neighbors and spreading these link quality
information through the whole mesh. This procedure is
summarized on the BATMAN concept page and explained in
details in the RFC draft published in 2008.
This approach was chosen for its simplicity during the
protocol design phase and the implementation. However, it
also bears some drawbacks:
* Wireless interfaces usually come with some packet loss,
therefore a higher broadcast rate is desirable to allow
a fast reaction on flaky connections.
Other interfaces of the same host might be connected to
Ethernet LANs / VPNs / etc which rarely exhibit packet
loss would benefit from a lower broadcast rate to reduce
overhead.
* It generally is more desirable to detect local link
quality changes at a faster rate than propagating all
these changes through the entire mesh (the far end of
the mesh does not need to care about local link quality
changes that much). Other optimizations strategies, like
reducing overhead, might be possible if OGMs weren't
used for all tasks in the mesh at the same time.
As a result detecting local link qualities shall be handled
by an independent message type, ELP, whereas the OGM message
type remains responsible for flooding the mesh with these
link quality information and determining the overall path
transmit qualities.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
