IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since functions never returns meaningfull value.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices need their multicast filter reset but others are crashed by that.
So the methods need to be separated.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: "Ridgway, Keith" <kridgway@harris.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX checksum offload is used, if the computed checksum is 0 the
LAN95xx device do not alter the checksum to 0xffff. In the case of ipv4
UDP checksum, it indicates to receiver that no checksum is calculated.
Under ipv6, UDP checksum yields a result of zero must be changed to
0xffff. Hence disabling checksum offload for ipv6 packets.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Reported-by: popcorn mix <popcornmix@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/net1080.c:271:20: error: unused function
'nc_dump_ttl' [-Werror,-Wunused-function]
Also remove the definition of TTL_THIS, which is only used in
nc_dump_ttl()
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
[-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing endianness conversions to a debug statement printing
the USB device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zero padding that is added to NTB's does
not zero the memory correctly.
This is because the skb_put modifies the value
of skb_out->len which results in the memset
command not setting any memory to zero as
(ctx->tx_max - skb_out->len) == 0.
I have resolved this by storing the size of
the memory to be zeroed before the skb_put
and using this in the memset call.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
This patch adds support for the PL-27A1 by adding the appropriate
USB ID's. This chip is used in the goobay Active USB 3.0 Data Link
and Unitek Y-3501 cables.
Signed-off-by: Roman Spychała <roed@onet.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use skb_cow_head() to properly deal with clones,
especially the ones coming from TCP stack that allow their head being
modified. This avoids a copy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: 4a476bd6d1 ("usbnet: New driver for QinHeng CH9200 devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: cc28a20e77 ("introduce cx82310_eth: Conexant CX82310-based ADSL router USB ethernet driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was failing to check that the SKB wasn't cloned
before adding checksum data.
Replace existing handling to extend/copy the header buffer
with skb_cow_head.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is used by a lot of embedded devices and also by the Raspberry
Pi 1, 2 & 3 which were created to promote the study of computer
sciences. Students wanting to learn kernel / network device driver
programming through those devices can only rely on the Linux kernel
driver source to make their own.
This commit adds a lot of comments to the registers definition to expand
the register names.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: Martin Wetterwald <martin@wetterwald.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE920A4 uses the same pid 0x1201 of LE920, but modem
implementation is different, since it requires DTR to be set for
answering to qmi messages.
This patch replaces QMI_FIXED_INTF with QMI_QUIRK_SET_DTR: tests on
LE920 have been performed in order to verify backward compatibility.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
pegasus, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Cc: Petko Manolov <petkan@nucleusys.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
kaweth_device, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GCC 6.3, we can get the following warning:
drivers/net/usb/usbnet.c:85:19: warning: 'driver_name' defined but not
used [-Wunused-const-variable=]
static const char driver_name [] = "usbnet";
^~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.
This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).
The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this the generic cdc_ether grabs the device,
and does not really work.
Signed-off-by: René Rebe <rene@exactcode.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for qmap mux protocol available in recent
Qualcomm based modems.
The qmap mux protocol can be used for multiplexing data packets in
order to have multiple ip streams through the same physical device.
Two new sysfs files are added for adding/removing the qmap mux based
interfaces (named qmimux):
- /sys/class/net/<iface>/qmi/add_mux
- /sys/class/net/<iface>/qmi/del_mux
Main patch author is Bjørn Mork <bjorn@mork.no>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.
The another similar case is
1. unplug the cable.
2. interrupt transfer queue a work_queue for linking change.
3. device enters the ALDPS mode.
4. a tx occurs before the work_queue is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx appears to use phylib in a rather weird way, accessing the PHY
partly through phylib, and partly by making direct accesses to it,
including to the Clause 45 registers. As the indirect MMD accessors are
going away, update this driver to use the plain phy_(read|write)_mmd()
accessors instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit a59e6d8152 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets qmicli working with the MDM6600 modem.
Cc: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check hw version first in probe(). Do nothing if the driver doesn't
support the chip.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function usbnet_{get|set}_settings is no longer used,
so we remove it.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: poma <poma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We add the new api {get|set}_link_ksettings to this driver.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.
BUG: unable to handle kernel NULL pointer dereference at 000000000000008
IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
PGD 0
Oops: 0002 [#1] SMP
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace &tp->napi with napi and tp->netdev with netdev.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The call to asix_write_medium_mode is not updating the return code ret
and yet ret is being checked for an error. Fix this by assigning ret to
the return code from the call asix_write_medium_mode.
Detected by CoverityScan, CID#1357148 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
swith||switch
swithable||switchable
swithed||switched
swithing||switching
While we are here, fix the "update" to "updates" in the touched hunk in
drivers/net/wireless/marvell/mwifiex/wmm.c.
Link: http://lkml.kernel.org/r/1481573103-11329-2-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/net/usb/lan78xx.c:394:33: sparse: expected ; at end of declaration
drivers/net/usb/lan78xx.c:394:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/usb/lan78xx.c:394:33: sparse: got interface
drivers/net/usb/lan78xx.c:403:1: sparse: Expected ; at the end of type declaration
drivers/net/usb/lan78xx.c:403:1: sparse: got }
Add linux/phy.h to lan78xx.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
References: https://bugs.debian.org/852556
Reported-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Tested-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule the napi after napi_enable() for rx, if it is necessary.
If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another rebranded Novatel E371. qmi_wwan should drive this device, while
cdc_ether should ignore it. Even though the USB descriptors are plain
CDC-ETHER that USB interface is a QMI interface. Ref commit 7fdb7846c9
("qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN
card")
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime suspend shouldn't be executed if the tx queue is not empty,
because the device is not idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_post_reset() should sumbit rx urb and interrupt transfer,
otherwise the rx wouldn't work and the linking change couldn't be
detected.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/usb/cdc_ether.c:469:6: warning:
symbol 'usbnet_cdc_zte_status' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the hw rx checksum is always enabled, and the user couldn't switch
it to sw rx checksum.
Note that the RTL_VER_01 only support sw rx checksum only. Besides,
the hw rx checksum for RTL_VER_02 is disabled after
commit b9a321b48a ("r8152: Fix broken RX checksums."). Re-enable it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.
If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add LAN7801 MAC only support with phy fixup functions.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function lan78xx_probe(), variable ret takes the errno code on
failures. However, when the call to usb_alloc_urb() fails, its value
will keeps 0. 0 indicates success in the context, which is inconsistent
with the execution result. This patch fixes the bug, assigning
"-ENOMEM" to ret when usb_alloc_urb() returns a NULL pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188771
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PID 0x1040 of Telit LE922A.
The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduced a work-around in usbnet_cdc_status() for devices that exported
cdc carrier on twice on connect. Before the commit, this behavior caused
the link state to be incorrect. It was assumed that all CDC Ethernet
devices would either export this behavior, or send one off and then one on
notification (which seems to be the default behavior).
Unfortunately, it turns out multiple devices sends a connection
notification multiple times per second (via an interrupt), even when
connection state does not change. This has been observed with several
different USB LAN dongles (at least), for example 13b1:0041 (Linksys).
After bfe9b9d2df, the link state has been set as down and then up for
each notification. This has caused a flood of Netlink NEWLINK messages and
syslog to be flooded with messages similar to:
cdc_ether 2-1:2.0 eth1: kevent 12 may have been dropped
This commit fixes the behavior by reverting usbnet_cdc_status() to how it
was before bfe9b9d2df. The work-around has been moved to a separate
status-function which is only called when a known, affect device is
detected.
v1->v2:
* Do not open-code netif_carrier_ok() (thanks Henning Schild).
* Call netif_carrier_off() instead of usb_link_change(). This prevents
calling schedule_work() twice without giving the work queue a chance to be
processed (thanks Bjørn Mork).
Fixes: bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes AX88772_suspend() USB vendor commands failure issues.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate mdix code to phy driver to be called at config_init().
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If usb_submit_urb() called from the open function fails, the following
crash may be observed.
r8152 8-1:1.0 eth0: intr_urb submit failed: -19
...
r8152 8-1:1.0 eth0: v1.08.3
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b7b
pgd = ffffffc0e7305000
[6b6b6b6b6b6b6b7b] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
...
PC is at notifier_chain_register+0x2c/0x58
LR is at blocking_notifier_chain_register+0x54/0x70
...
Call trace:
[<ffffffc0002407f8>] notifier_chain_register+0x2c/0x58
[<ffffffc000240bdc>] blocking_notifier_chain_register+0x54/0x70
[<ffffffc00026991c>] register_pm_notifier+0x24/0x2c
[<ffffffbffc183200>] rtl8152_open+0x3dc/0x3f8 [r8152]
[<ffffffc000808000>] __dev_open+0xac/0x104
[<ffffffc0008082f8>] __dev_change_flags+0xb0/0x148
[<ffffffc0008083c4>] dev_change_flags+0x34/0x70
[<ffffffc000818344>] do_setlink+0x2c8/0x888
[<ffffffc0008199d4>] rtnl_newlink+0x328/0x644
[<ffffffc000819e98>] rtnetlink_rcv_msg+0x1a8/0x1d4
[<ffffffc0008373c8>] netlink_rcv_skb+0x68/0xd0
[<ffffffc000817990>] rtnetlink_rcv+0x2c/0x3c
[<ffffffc000836d1c>] netlink_unicast+0x16c/0x234
[<ffffffc00083720c>] netlink_sendmsg+0x340/0x364
[<ffffffc0007e85d0>] sock_sendmsg+0x48/0x60
[<ffffffc0007e9c30>] SyS_sendto+0xe0/0x120
[<ffffffc0007e9cb0>] SyS_send+0x40/0x4c
[<ffffffc000203e34>] el0_svc_naked+0x24/0x28
Clean up error handling to avoid registering the notifier if the open
function is going to fail.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Cypress GX3 SuperSpeed to Gigabit Ethernet
Bridge Controller (Vendor=04b4 ProdID=3610).
Patch verified on x64 linux kernel 4.7.4, 4.8.6, 4.9-rc4 systems
with the Kensington SD4600P USB-C Universal Dock with Power,
which uses the Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge
Controller.
A similar patch was signed-off and tested-by Allan Chou
<allan@asix.com.tw> on 2015-12-01.
Allan verified his similar patch on x86 Linux kernel 4.1.6 system
with Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge Controller.
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Chris Roth <chris.roth@usask.ca>
Tested-by: Artjom Simon <artjom.simon@gmail.com>
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Chris Roth <chris.roth@usask.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
To utilize phylib with interrupt fully than handling some of phy stuff in the MAC driver,
create irq_domain for USB interrupt EP of phy interrupt and
pass the irq number to phy_connect_direct() instead of PHY_IGNORE_INTERRUPT.
Idea comes from drivers/gpio/gpio-dl2.c
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 driver has been broken since (approx) 3.16.xx
when support was added for hardware RX checksums
on newer chip versions. Symptoms include random
segfaults and silent data corruption over NFS.
The hardware checksum logig does not work on the VER_02
dongles I have here when used with a slow embedded system CPU.
Google reveals others reporting similar issues on Raspberry Pi.
So, disable hardware RX checksum support for VER_02, and fix
an obvious coding error for IPV6 checksums in the same function.
Because this bug results in silent data corruption,
it is a good candidate for back-porting to -stable >= 3.16.xx.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kalmia_send_init_packet() returns zero or a negative return
code, but gcc has no way of knowing that there cannot be a
positive return code, so it determines that copying the ethernet
address at the end of kalmia_bind() will access uninitialized
data:
drivers/net/usb/kalmia.c: In function ‘kalmia_bind’:
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)ðernet_addr+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
*((short *)to + 2) = *((short *)from + 2);
^
drivers/net/usb/kalmia.c:138:5: note: ‘*((void *)ðernet_addr+4)’ was declared here
This warning is harmless, but for consistency, we should make
the check for the return code match what the driver does everywhere
else and just progate it, which then gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
max_mtu and/or min_mtu as needed)
r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)
lan78xx:
- Set max_mtu = 9000
asix_driver:
- max_mtu = 16384 for ax88178 variant
ax88179:
- max_mtu = 4088
cdc_ncm:
- max_mtu from hardware
cdc-phonet:
- min_mtu = 6, max_mtu = 65541
sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
usbnet_change_mtu, but if we set max_mtu to let the network core handle
the range check, then we can simply call usbnet_change_mtu directly
smsc75xx:
- max_mtu = 9000
CC: netdev@vger.kernel.org
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: Hayes Wang <hayeswang@realtek.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following four products of Lenovo and sort the order of the list.
VID PID
0x17ef 0x3062
0x17ef 0x3069
0x17ef 0x720c
0x17ef 0x7214
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check answers from USB stack and avoid re-sending the request
multiple times if the device does not respond.
This fixes the following problem, observed with a probably flaky adapter.
[62108.732707] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[62108.914421] usb 1-3: New USB device found, idVendor=0b95, idProduct=7720
[62108.914463] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[62108.914476] usb 1-3: Product: AX88x72A
[62108.914486] usb 1-3: Manufacturer: ASIX Elec. Corp.
[62108.914495] usb 1-3: SerialNumber: 000001
[62114.109109] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
[62114.109139] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to send software reset: ffffff92
[62119.109048] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
...
Since the USB timeout is 5 seconds, and the operation is retried 30 times,
this results in
[62278.180353] INFO: task mtpd:1725 blocked for more than 120 seconds.
[62278.180373] Tainted: G W 3.18.0-13298-g94ace9e #1
[62278.180383] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
...
[62278.180957] kworker/2:0 D 0000000000000000 0 5744 2 0x00000000
[62278.180978] Workqueue: usb_hub_wq hub_event
[62278.181029] ffff880177f833b8 0000000000000046 ffff88017fd00000 ffff88017b126d80
[62278.181048] ffff880177f83fd8 ffff880065a71b60 0000000000013340 ffff880065a71b60
[62278.181065] 0000000000000286 0000000103b1c199 0000000000001388 0000000000000002
[62278.181081] Call Trace:
[62278.181092] [<ffffffff8e0971fd>] ? console_conditional_schedule+0x2c/0x2c
[62278.181105] [<ffffffff8e094f7b>] schedule+0x69/0x6b
[62278.181117] [<ffffffff8e0972e0>] schedule_timeout+0xe3/0x11d
[62278.181133] [<ffffffff8daadb1b>] ? trace_timer_start+0x51/0x51
[62278.181146] [<ffffffff8e095a05>] do_wait_for_common+0x12f/0x16c
[62278.181162] [<ffffffff8da856a7>] ? wake_up_process+0x39/0x39
[62278.181174] [<ffffffff8e095aee>] wait_for_common+0x52/0x6d
[62278.181187] [<ffffffff8e095b3b>] wait_for_completion_timeout+0x13/0x15
[62278.181201] [<ffffffff8de676ce>] usb_start_wait_urb+0x93/0xf1
[62278.181214] [<ffffffff8de6780d>] usb_control_msg+0xe1/0x11d
[62278.181230] [<ffffffffc037d629>] usbnet_write_cmd+0x9c/0xc6 [usbnet]
[62278.181286] [<ffffffffc03af793>] asix_write_cmd+0x4e/0x7e [asix]
[62278.181300] [<ffffffffc03afb41>] asix_set_sw_mii+0x25/0x4e [asix]
[62278.181314] [<ffffffffc03b001d>] asix_mdio_read+0x51/0x109 [asix]
...
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quectel EC21 and EC25 need the same "set DTR" request as devices
based on the MDM9230 chipset, but has no USB3 support. Our best guess
is that the "set DTR" functionality depends on chipset and/or
baseband firmware generation. But USB3 is still an optional feature.
Since we cannot enable this unconditionally for all older devices, and
there doesn't appear to be anything we can use in the USB descriptors
to identify these chips, we are forced to use a device specific quirk
flag.
Reported-and-tested-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions forward.
r8152_mmd_indirect()
r8152_mmd_read()
r8152_mmd_write()
r8152_eee_en()
r8152b_enable_eee()
r8153_eee_en()
r8153_enable_eee()
r8152b_enable_fc()
r8153_aldps_en()
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more common logging style
Miscellanea:
o Add pr_fmt to prefix each output message
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macros that end in an underscore are just odd.
Add hso_dbg(level, fmt, ...) and use it everwhere instead.
Several uses had additional unnecessary newlines as the
macro added a newline. Remove the newline from the macro
and add newlines to each use as appropriate.
Remove now unused D<digit> macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "pegasus_workqueue" queues a single work item per pegasus
instance and hence it doesn't require execution ordering. Hence,
alloc_workqueue has been used to replace the deprecated
create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure since it's a network driver.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check the coding style with checkpatch.pl and fix the warnings and errors.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Grant Grundler <grundler@chromium.org>
The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.
The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.
Ignore the ret value since it's ignored in XXX_link_reset() functions.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Grant Grundler <grundler@chromium.org>
https://lkml.org/lkml/2014/11/11/947
Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Allan Chou <allan@asix.com.tw>
The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Vincent Palatin <vpalatin@chromium.org>
Check the answers from the USB stack and avoid re-sending multiple times
the request if the device has disappeared.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Freddy Xin <freddy@asix.com.tw>
In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.
Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.
Reset HW in resume function to ensure the PHY works correctly.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the oops discovered by the Umap2 project and Alan Stern.
The intf member needs to be set before the firmware is downloaded.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
