IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).
* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.
Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds support for HDMI audio to the device tree
common to the HiHope RZ/G2M and the HiHope RZ/G2N.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")'
introduces two new clocks to gcc. These are not used before
clk_disable_unused() and as such the clock framework tries to disable
them.
But on the EVB these registers are only accessible through TrustZone, so
these clocks must be marked as "protected" to prevent the clock code
from touching them.
Numerical values are used as the constants are not yet available in a
common tree.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
P710 is a RK3399 based SBC, designed by Leez [0].
Specification
- Rockchip RK3399
- 4/2GB LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
[0]https://leez.lenovo.com
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rockpro64 contains a nor-flash chip connected to spi1.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
[a number of cleanups]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- a few small DT fixes for g12a/g12b platforms
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEe4dGDhaSf6n1v/EMWTcYmtP7xmUFAl1R+ZIACgkQWTcYmtP7
xmWjDw//ZxsyTeWzq1swqj7ORhqmfs7ayUk8K137O7oHb0d85bEFzY4R2x5ralLN
H92HdYSY4PiuOHk5Eya2Xbp+RVsbJNiyywMzdUuPHnN1i7/NlnPxZh/fgbb/hhC/
Cp+z7MWg7t7/jNxS9K1Fy+bnk5Y2krc2bfOfC9Bs2RpBerJuQzq4vMs603oNf+Ho
GEV6OM4NFflPM+fz3iGiBOGa/GHaCKgYsgqgS95aUW3oc7XAC5zLwCG8DUCOJ7/j
o/6jso7NTEy7MSaJ5IZjTCzN4LZRBoc69ruueFB67B6O6aqbrd3JwWXXe5lRYIr6
Epg03Ated983tB7+M1ToQMbZBJ6hiRQtdYHwyul7qScKtf+mbobETB7iiPcr21pB
Yw+i671cUas/L4BeoHdSwE90pxJdMRHVg0rYVgSZr7CYZTvYwhPba5Hk330vPeCv
8TFLpj89f710Ya+GaiFndGhnazbLlytgShPE+Vztnr6Uewk56W6T3QK0B6+Em7GD
fYO7mdW3pF72YYAK+x8P+u0puq6nwJhFKRUKV82roNhzIGQZcPKmqDC1KJ2YUiAu
1c80I/00E0Fd+CtDLewXQ67JVRMa+qldgMyVIW0BlNm1scxwSC9T/4g+ixsU0uUB
naCO/AG9MJ7MeZT31QjA8lrQh9vriURPOcgama5eTHOrjkcg1Wg=
=bMaE
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
arm64: dts: Amlogic fixes for v5.3-rc
- a few small DT fixes for g12a/g12b platforms
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
Single patch removing optional 'max-memory-bandwidth' property for CLCD
that enables to allocate and use 32bpp buffers(used on FVP for Android
development)
-----BEGIN PGP SIGNATURE-----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=nrQp
-----END PGP SIGNATURE-----
Merge tag 'juno-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/FVP update for v5.4
Single patch removing optional 'max-memory-bandwidth' property for CLCD
that enables to allocate and use 32bpp buffers(used on FVP for Android
development)
* tag 'juno-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: fast models: Remove clcd's max-memory-bandwidth
Link: https://lore.kernel.org/r/20190814172408.25995-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable DVFS for the Odroid-N2 by setting the clock, OPP and supply
for each cores of each CPU clusters.
The first cluster uses the "VDDCPU_B" power supply, and the second
cluster uses the "VDDCPU_A" power supply.
Each power supply can achieve 0.73V to 1.01V using 2 distinct PWM
outputs clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of each cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM3 uses the Amlogic S922X or A311S SoC, both based on the
Amlogic G12B SoC family, on a board with the same form factor as the
VIM/VIM2 models. It ships in two variants; basic and
pro which differ in RAM and eMMC size:
- 2GB (basic) or 4GB (pro) LPDDR4 RAM
- 16GB (basic) or 32GB (pro) eMMC 5.1 storage
- 16MB SPI flash
- 10/100/1000 Base-T Ethernet
- AP6398S Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 1x USB 2.0 + 1x USB 3.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 3x LED's (1x red, 1x blue, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- M2 socket with PCIe, USB, ADC & I2C
- 40pin GPIO Header
- 1x micro SD card slot
A common meson-g12b-khadas-vim3.dtsi is added to support both S922X and
A311D SoCs supported by two variants of the board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently there are two nodes named "regulator1" in the Draak DTS: a
3.3V regulator for the eMMC and the LVDS decoder, and a 12V regulator
for the backlight. This causes the former to be overwritten by the
latter.
Fix this by renaming all regulators with numerical suffixes to use named
suffixes, which are less likely to conflict.
Fixes: 4fbd4158fe8967e9 ("arm64: dts: renesas: r8a77995: draak: Add backlight")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Arm per-CPU architected timers stop ticking in suspend, when the
SCP powers down the CPUs. Flag that in the DT.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson g12b ships with a low-speed (S922X) and high-speed (A311D) variant
so remove cpu_opp_table nodes in meson-g12b.dtsi and create two new dtsi
that can be included in device-specific dts files. Opp points were taken
from the vendor BSP kernel.
Also make meson-g12b-odroid-n2.dts include the new meson-g12b-s922x.dtsi.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables the video decoder for GXBB, GXL and GXM chips
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the base video decoder node compatible with the meson vdec driver,
for GX* chips.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheets in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the OPP table taken from the HardKernel Odroid-N2 DTS.
The Amlogic G12B SoC seems to available in 2 types :
- low-speed: Cortex-A73 Cluster up to 1,704GHz
- high-speed: Cortex-A73 Cluster up to 2.208GHz
The Cortex-A73 Cluster can be clocked up to 1,896GHz for both types.
The Vendor Amlogic A311D OPP table are slighly different, with lower
voltages than the HardKernel S922X tables but seems to be high-speed type.
This adds the conservative OPP table with the S922X higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an HardKernel Odroid-N2 board
running the arm64 cpuburn at [1] and cycling between all the possible
cpufreq translations for both clusters and checking the final frequency
using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board
by setting the clock, OPP and supply for each CPU cores.
The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM
output clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations and checking the final
frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the OPP table taken from the vendor u200 and u211 DTS.
The Amlogic G12A SoC seems to available in 3 types :
- low-speed: up to 1,8GHz
- mid-speed: up to 1,908GHz
- high-speed: up to 2.1GHz
And the S905X2 opp voltages are slightly higher than the S905D2
OPP voltages for the low-speed table.
This adds the conservative OPP table with the S905X2 higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an Amlogic U200 Reference Board,
SeiRobotics SEI510 and X96 Max Set-Top-Boxes running the arm64 cpuburn
at [1] and cycling between all the possible cpufreq translations and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the ao_pinctrl subnode for the pwm_a function on GPIOE_2.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
To simplify the representation of differences betweem the G12A and G12B
SoCs, move the common nodes into a meson-g12-common.dtsi file and
express the CPU nodes and differences in meson-g12a.dtsi and meson-g12b.dtsi.
This separation will help for DVFS and future Amlogic SM1 Family support.
The sd_emmc_a quirk is added in the g12a/g12b since since it's already
known the sd_emmc_a controller is fixed in the next SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Longcheer L8150 is a smartphone based on MSM8916 which is
used in several rebrands like the Snapdragon 410
Android One devices or the Wileyfox Swift.
Add a device tree for L8150 with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
Co-developed-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Samsung Galaxy A3 (SM-A300FU) and Samsung Galaxy A5 (SM-A500FU)
are smartphones using the MSM8916 SoC released in 2015.
Add a device tree for A3U and A5U with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502 MUIC)
- Regulators
The two devices (and all other variants of A3/A5 released in 2015)
are very similar, with some differences in display, touchscreen
and sensors. The common parts are shared in
msm8916-samsung-a2015-common.dtsi to reduce duplication.
The device tree is loosely based on apq8016-sbc.dtsi and the
downstream kernel provided by Samsung, mixed with a lot of own
research.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds Qualcomm Venus video codec DT node for the video
codec hardware found in MSM8996 platforms.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
AOSS hosts resources that can be used to warm up the SoC.
Add nodes for these resources.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable coresight support by adding device nodes for the
available source, sinks and channel blocks on msm8996.
This also adds coresight cpu debug nodes.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable coresight support by adding device nodes for the
available source, sinks and channel blocks on MSM8998.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DT nodes should be ordered by address, then node name, and finally label.
The msm8998 dtsi does not follow this, so clean it up by reordering the
nodes. While we are at it, extend the addresses to be fully 32-bits wide
so that ordering is easy to determine when adding new nodes. Also, two
or so nodes had the wrong address value in their node name (did not match
the reg property), so fix those up as well.
Hopefully going forward, things can be maintained so that a cleanup like
this is not needed.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them
arch/arm64/boot/dts/qcom/qcs404.dtsi:1080.31-1084.7: Warning (unit_address_vs_reg): /thermal-zones/aoss-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1095.33-1099.7: Warning (unit_address_vs_reg): /thermal-zones/q6-hvx-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1110.32-1114.7: Warning (unit_address_vs_reg): /thermal-zones/lpass-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1125.31-1129.7: Warning (unit_address_vs_reg): /thermal-zones/wlan-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1140.34-1144.7: Warning (unit_address_vs_reg): /thermal-zones/cluster-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1145.34-1149.7: Warning (unit_address_vs_reg): /thermal-zones/cluster-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1174.31-1178.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1179.31-1183.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1208.31-1212.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1213.31-1217.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1242.31-1246.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1247.31-1251.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1276.31-1280.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1281.31-1285.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1310.30-1314.7: Warning (unit_address_vs_reg): /thermal-zones/gpu-thermal/trips/trip-point@0: node has a unit name, but no reg property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
pms405@1 nodes specified unnecessary #address-cells/#size-cells but the
subnodes dont have "ranges" or "reg" so remove it
arch/arm64/boot/dts/qcom/pms405.dtsi:141.21-150.4: Warning (avoid_unnecessary_addr_size): /soc@0/spmi@200f000/pms405@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The adc nodes have reg property but were missing the unit name, so add
that to fix these warnings:
arch/arm64/boot/dts/qcom/pms405.dtsi:91.12-94.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/ref_gnd: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:96.14-99.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/vref_1p25: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:101.19-104.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/vph_pwr: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:106.13-109.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/die_temp: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:111.27-116.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/thermistor1: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:118.27-123.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/thermistor3: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:125.22-130.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/xo_temp: node has a reg or ranges property, but no unit name
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Last level cache (aka. system cache) controller provides control
over the last level cache present on SDM845. This cache lies after
the memory noc, right before the DDR.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Node names shouldn't include a vendor prefix and should whenever
possible use a generic identifier. Resolve this by renaming the smmu
nodes "iommu".
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When powering off the Odroid N2, the tflash_vdd regulator is
automatically turned off by the kernel. This is a problem
when issuing the "reboot" command while using an SD card.
The boot ROM does not power this regulator back on, blocking
the reboot process at the boot ROM stage, preventing the
SD card from being detected.
Adding the "regulator-always-on" property fixes the problem.
Signed-off-by: Xavier Ruppen <xruppen@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: c35f6dc5c377 ("arm64: dts: meson: Add minimal support for Odroid-N2")
[khilman: minor subject change: s/meson/amlogic/]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the IR receiver controller on the SEI510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The G12A USB2 OTG capable PHY uses a 8bit large UTMI bus, and the OTG
controller gets the PHY but width by probing the associated phy.
By default it will use 16bit wide settings if a phy is not specified,
in our case we specified the phy, but not the phy-names.
The dwc2 bindings specifies that if phys is present, phy-names shall be
"usb2-phy".
Adding phy-names = "usb2-phy" solves the OTG PHY bus configuration.
Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Power rail "D12.0V" comes straight from the power barrel connector,
and it's used in both main board and sub board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Based on similar work from Laurent Pinchart for the r8a7799[05].
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Sort sound child nodes]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
