IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In 63b77bf489881747c5118476918cc8c29378ee63
iwlwifi: dvm: don't send zeroed LQ cmd
I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341
Cc: stable@vger.kernel.org
Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing the MAC address of a single vif mac80211 will check if
the new address fits into the address mask specified by the driver.
This only needs to be done when using multiple BSSIDs. Hence, check
the new address only against all other vifs.
Also fix the MAC address assignment on new interfaces if the user
changed the address of a vif such that perm_addr is not covered by
addr_mask anymore.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=57371
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Bruno Randolf <br1@thinktube.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.
To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.
For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.
For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was an extra ';' character added to the end of the if statement
which means that it always prints that the /proc entry wasn't created
even though it was.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Waiting for all subframes of an existing aggregation session to drain
before allowing mac80211 to start a new one is fragile and deadlocks
caused by this behavior have been observed.
Since mac80211 has proper synchronization for aggregation session
start/stop handling, a better approach to session handling is to simply
allow mac80211 to start a new session at any time. This requires
changing the code to discard any packets outside of the BlockAck window
in the A-MPDU software retry code.
This patch implements the above and also simplifies the code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- 3 fixes for the NFC MEI support:
* We now depend on the correct Kconfig symbol.
* We register an MEI event callback whenever we enable an NFC device,
otherwise we fail to read anything after an enable/disable cycle.
* We only disable an MEI device from its disable mey_phy_ops,
preventing useless consecutive disable calls.
- An NFC Makefile cleanup, as I forgot to remove a commented out line when
moving the LLCP code to the NFC top level directory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=24Oz
-----END PGP SIGNATURE-----
Samuel Ortiz <sameo@linux.intel.com> says:
"Merge tag 'nfc-fixes-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
This is the first batch of NFC fixes for 3.10, and it contains:
- 3 fixes for the NFC MEI support:
* We now depend on the correct Kconfig symbol.
* We register an MEI event callback whenever we enable an NFC device,
otherwise we fail to read anything after an enable/disable cycle.
* We only disable an MEI device from its disable mey_phy_ops,
preventing useless consecutive disable calls.
- An NFC Makefile cleanup, as I forgot to remove a commented out line when
moving the LLCP code to the NFC top level directory."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback registration starts a waiting read, so it needs to be fired
everytime the device is enabled. Otherwise following writes will never get
an answer back.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Kconfig symbol NFC_LLCP was removed in commit 30cc458765 ("NFC: Move
LLCP code to the NFC top level diirectory"). But the reference to its
macro in this Makefile was only commented out. Remove it now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After a tx attempt, an A-MPDU subframe can still have fi->retries at 0
(if the retry count wasn't incremented due to powersave).
In that case it is still tracked as part of the block ack window, so
when draining the tid queue, its sequence number needs to be cleared
from the pending frame bitmap.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some issues introduced in the rate control API rework.
When not running aggregation, copy bf->rates into info->control.rates
before applying the rate control status to it.
In ath_lookup_rate, the rates need to be pulled from bf->rates, not the
tx info.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation stop is requested, don't run the mac80211 aggregation
stop callback yet, while the session is still blocked.
Also, when aggregation flush is requested, don't run the callback at all.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Manual peak calibration is currently enabled only for
AR9462 and AR9565. This is also required for AR9485.
The initvals are also modified to disable HW peak calibration.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the USB ID of the On Networks N300MA, clone of Netgear WNA3100M.
Signed-off-by: Albert Pool <albertpool@solcon.nl>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Ana Rey <Anazul77@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P2P_DEVICE support was removed from brcmfmac for v3.9 kernel with
the commit below:
commit 1527c343c12f3a2aae532aa881d12c6fbf8749f4
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Apr 4 12:10:11 2013 +0200
brcmfmac: remove advertising P2P device support
However, it got merged into wireless-next. But for 3.10 brcmfmac does
support P2P device. Putting it back with this commit.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In http://lkml.indiana.edu/hypermail/linux/kernel/1305.1/index.html,
Geert Uytterhoeven reports a new warning when building 3.10-rc1 in
this driver. This is caused by using a "#if" test to see if __LITTLE_ENDIAN
is set, which fails for all big-endian systems. Change to "ifdef".
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If NO_DMA=y:
drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCIe and ARM CR4 cores were found on 14e4:43b1 AKA BCM4352.
Reported-by: Gabriel Thörnblad <gabriel@thornblad.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EXPORT_SYMBOL and inline directives are contradictory to each other.
The patch fixes this inconsistency.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We send direct probe to broadcast address, as some APs do not respond to
unicast PROBE frames when unassociated. Broadcast frames are not acked,
so we can not use that for trigger MLME state machine, but we need to
use old timeout mechanism.
This fixes authentication timed out like below:
[ 1024.671974] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 1024.694125] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 1024.695450] wlan6: direct probe to 54:e6:fc:98:63:fe (try 2/3)
[ 1024.700586] wlan6: send auth to 54:e6:fc:98:63:fe (try 3/3)
[ 1024.701441] wlan6: authentication with 54:e6:fc:98:63:fe timed out
With fix, we have:
[ 4524.198978] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 4524.220692] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 4524.421784] wlan6: send auth to 54:e6:fc:98:63:fe (try 2/3)
[ 4524.423272] wlan6: authenticated
[ 4524.423811] wlan6: associate with 54:e6:fc:98:63:fe (try 1/3)
[ 4524.427492] wlan6: RX AssocResp from 54:e6:fc:98:63:fe (capab=0x431 status=0 aid=1)
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.
Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.
Cc: stable@vger.kernel.org [3.9]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the normal flow first MAC_CONTEXT_CMD for particular interface is
never sent while associated. The exception is fw restart flow when
resuming from suspend when WoWLAN is enabled. In this case successive
"add" and "modify" MAC_CONTEXT_CMD commands may be sent with assoc flag
set what cause FW mal functioning. To prevent this never set assoc flag
in MAC_CONTEXT_CMD with action "add".
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this command, the firmware will filter out all the
multicast frames. Let them all in as for now. Later we will
want to optimize this to save power.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW AUX framework does not handle well cases where time events
fail to be scheduled (and as a result issues assert 0x3330). Until
a proper fix is in place, WA this by always setting the scan type to
SCAN_TYPE_FORCED.
Cc: stable@vger.kernel.org
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the frame isn't transmitted to the AP, we need to
report it to cfg80211 so the state there can be updated
correctly.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the interface goes down, there's no need to call
cfg80211_mlme_down() after __cfg80211_disconnect() as
the latter will call the former (if appropriate.)
Also, in __cfg80211_disconnect(), if the cfg80211 SME
isn't used, __cfg80211_disconnected() may still need
to be called (depending on the current state) so that
the SME state gets cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, ignore frames with mis-matched BSSID that aren't
multicast or sent to the correct destination. This fixes
reporting public action frames to userspace multiple times
on multiple virtual AP interfaces.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the attributes fixes an issue with P2P Device not
working properly for management frame TX.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_get_tkip_p2k() may be called with interrupts
disabled, so spin_unlock_bh() isn't safe and leads to
warnings. Since it's always called with BHs disabled
already, just use spin_lock().
Cc: stable@vger.kernel.org
Reported-by: Milan Kocian <milon@wq.cz>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Document rx vs tx status concurrency requirements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 12e7f517029dad819c45eca9ca01fdb9ba57616b,
IEEE80211_SDATA_DISCONNECT_RESUME no longer worked as
it would simply never be tested. Restore a bit of the
code removed there and in 9b7d72c1041ec5b20b24af487a9
to make it work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device reports a non-wireless wakeup reason, the
tracing code crashes trying to dereference a NULL pointer.
Fix this by checking the pointer on all accesses and also
add a non_wireless tag to the event.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not registering a platform_driver would make us access garbage
when the platform callbacks under driver_register() kicks in.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tested-By: Martin Pitt <martin.pitt@ubuntu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If rfkill_register() fails in wiphy_register() the struct device
is unregistered but everything else isn't (regulatory, debugfs)
and we even leave the wiphy instance on all internal lists even
though it will likely be freed soon, which is clearly a problem.
Fix this by cleaning up properly.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
Here is a batch of fixes intended for the 3.10 stream.
Amitkumar Karwar provides an mwifiex fix to plug a memory leak when
the driver is unloaded.
Bing Zhao brings an mwifiex fix for some flag handling that leads to
log spam and an unusable interface.
Daniel Drake offers an mwifiex fix for multicast filter setup, to
correctly implement wakeup behaviour for multicast WOL.
Felix Fietkau fixes an ath9k problem that produces logspam and keycache
errors due to a bad return code.
Stanislaw Gruszka produces an fix for a WARNING from ath5k, and an
iwl4965 workaround to stop advertising a feature that doesn't work with
the current mac80211 implementation.
Sujith Manoharan gives us an ath9k fix to reprogram the HW beacon timers
after a TSF update, and an initvals fix for the AR9565 device.
Thommy Jakobsson fixes an rx descriptor underrun on b43.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Zw0E
-----END PGP SIGNATURE-----
Merge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull trivial pstore update from Tony Luck:
"Couple of pstore cleanups"
It turns out that the kmemdup() conversion ends up being undone by the
fact that the memory block also needed the ecc information (see commit
bd08ec33b5c2: "pstore/ram: Restore ecc information block"), so all that
remains after merging is the error return code change.
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore/ram: fix error return code in ramoops_probe()
fs: pstore: Replaced calls to kmalloc and memcpy with kmemdup
Pull NVMe driver update from Matthew Wilcox:
"Lots of exciting new features in the NVM Express driver this time,
including support for emulating SCSI commands, discard support and the
ability to submit per-sector metadata with I/Os.
It's still mostly bugfixes though!"
* git://git.infradead.org/users/willy/linux-nvme: (27 commits)
NVMe: Use user defined admin ioctl timeout
NVMe: Simplify Firmware Activate code slightly
NVMe: Only clear the enable bit when disabling controller
NVMe: Wait for device to acknowledge shutdown
NVMe: Schedule timeout for sync commands
NVMe: Meta-data support in NVME_IOCTL_SUBMIT_IO
NVMe: Device specific stripe size handling
NVMe: Split non-mergeable bio requests
NVMe: Remove dead code in nvme_dev_add
NVMe: Check for NULL memory in nvme_dev_add
NVMe: Fix error clean-up on nvme_alloc_queue
NVMe: Free admin queue on request_irq error
NVMe: Add scsi unmap to SG_IO
NVMe: queue usage fixes in nvme-scsi
NVMe: Set TASK_INTERRUPTIBLE before processing queues
NVMe: Add a character device for each nvme device
NVMe: Fix endian-related problems in user I/O submission path
NVMe: Fix I/O cancellation status on big-endian machines
NVMe: Fix sparse warnings in scsi emulation
NVMe: Don't fail initialisation unnecessarily
...
