IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ld_field instruction has the following format in NFP assembler:
ld_field[dst, 1000, src, <<24]
reoder parameters to emit_ld_field_any() to make it closer to
the familiar assembler order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ld_field instruction is a bit special because the encoding uses
two source registers and one of them becomes the output. We do
need to pass the dst register to our encoding helpers though,
otherwise the "write both banks" flag will not be observed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device expects the instructions in little endian. Make sure we
byte swap on big endian hosts.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to append up to 8 nops after last instruction to make
sure the CPU will not fetch garbage instructions with invalid
ECC if the code store was not initialized.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the initial PoC firmware I simply disabled ECC on the instruction
store. Do the ECC calculation for generated instructions in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datapath ABI version 2 stores the packet information in LMEM
instead of NNRs. We also have strict restrictions on which
GPRs we can use. Only GPRs 0-23 are reserved for BPF.
Adjust the static register locations and "ABI" registers.
Note that packet length is packed with other info so we have
to extract it into one of the scratch registers, OTOH since
LMEM can be used in restricted operands we don't have to
extract packet pointer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most instructions have special fields which allow switching
between base and extended Local Memory pointers. Introduce
those to register encoding, we will use the extra LM pointers
to access high addresses of the stack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Temporarily drop support for skb->mark. We are primarily focusing
on XDP offload, and implementing skb->mark on the new datapath has
lower priority.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the register renumbering optimization. To implement calling
map and other helpers we need more strict register layout. We can't
freely reassign register numbers.
This will have the effect of running in 4 context/thread mode, which
should be OK since we are moving towards integrating the BPF closer
with FW app datapath anyway, and the target datapath itself runs in
4 context mode.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add encodings of all 64bit shift operations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the software reg helpers and some static data to nfp_asm.c.
They are related to the previous patch, but move is done in a separate
commit for ease of review.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new __bitwise type for software representation of registers.
This will allow us to catch incorrect parameter types using sparse.
Accessors we define also allow us to return correct enum type and
therefore ensure all switches handle all register types.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements jiting of BPF_J{LT,LE} instructions with
BPF_X/BPF_K variants for the nfp eBPF JIT. The two BPF_J{SLT,SLE}
instructions have not been added yet given BPF_J{SGT,SGE} are
not supported yet either.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pure move of eBPF offload files to BPF app directory,
only change the names and relative header location.
nfp_asm.h stays in the main dir and it doesn't really
have to include nfp_bpf.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
