IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In bmps mode, beacons are filtered, and firmware is in charge
of monitoring the beacons and report changes or loss.
mac80211 must be advertised about such change to prevent it's
internal timer based beacon monitor to report beacon loss.
Fix that by setting/clearing the IEEE80211_VIF_BEACON_FILTER
vif flag on bmps entry/exit.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592471863-31402-2-git-send-email-loic.poulain@linaro.org
This is a small update to fix an error I saw where a few functions do not
have a blank line in between them.
Affects smd.c and main.c - no logic is affected by this change.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
This commit marks all smd.c functions that are only used inside of smd.c as
static. Previous commits added some VHT specific setup functions non-static
which is the right thing to do in terms of having granular git commits that
compile warning free. What we really want is for local not global scope on
those functions.
This patch makes the conversion from global to local scope.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-2-bryan.odonoghue@linaro.org
This patch adds ieee802.11 VHT flags for the wcn3680b.
- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream
RX LDPC is declared as supported in the datasheet but not enabled at this
time.
After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
In order to pass 802.11ac VHT parameters from the SoC to wcn36xx we need to
use the V1 data structures associated with BSS and STA parameters.
The means of identifying a V1 data-structure is via the SMD version field.
This patch defines a INIT_HAL_MSG_V1() which operates the same way as
INIT_HAL_MSG() with the exception that it defines VERSION1 as opposed to
VERSION0.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-2-bryan.odonoghue@linaro.org
This commit makes use of wcn36xx_smd_set_bss_vht_params() to extract VHT
parameters from the 80211_sta structure and latch appropriate bits in the
bss_params_v1 structure for transmission to the wcnss firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-5-bryan.odonoghue@linaro.org
This commit modifies wcn36xx_smd_start() so that it can download wcn3680
specific firmware parameters if we are talking to the wcn3680. If not the
original generic firmware parameter table should continue to be used for
wcn3620 and wcn3660.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-4-bryan.odonoghue@linaro.org
This commit defines a firmware configuration for the wcn3680 which
represents a working downstream configuration. This configuration has been
successfully applied to the upstream driver with antecedent patches
resulting in the same or better through-put in comparison to the
downstream driver on the test hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-3-bryan.odonoghue@linaro.org
In order to get 802.11ac working the way we want, additional parameters
need to be passed down to the firmware.
This patch takes the full remaining set of parameters defined in the
downstream riva/inc/wlan_hal_cfg.h and imports them into hal.h with some
minor name length adjustments.
This addition will allow us to pass a larger firmware configuration set
later on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-2-bryan.odonoghue@linaro.org
For the 80MHz channel we need to set the PHY mode to one of four PHY modes
that span the 80MHz range.
This patch latches the hw_value PHY field previously defined for 5GHz
channels directly to the parameter passed to the firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-6-bryan.odonoghue@linaro.org
This commit encodes the 802.11ac PHY mode for a given channel in the upper
bits of the hw_value field. This allows for a neat read-out and application
of the relevant PHY setting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-5-bryan.odonoghue@linaro.org
Adds HW_VALUE_PHY(hw_value) an access macro that will be used to
extract a hardware specific PHY setting for a given channel.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-4-bryan.odonoghue@linaro.org
Uses HW_VALUE_CHANNEL() to extract the channel number from a
struct ieee80211_channel->hw_value. Once done we can use the upper bits of
the hw_value to encode PHY related data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
Adds HW_VALUE_CHANNEL(hw_value) an access macro that will be used to
extract the channel number from struct ieee80211_channel->hw_value in
preparation for also storing PHY settings for 802.11ac in the upper bits of
hw_value.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-2-bryan.odonoghue@linaro.org
wcn36xx_smd_config_bss_v0() and wcn36xx_smd_config_bss_v1() have been
designed to operate in standalone fashion. As a result we can drop the
dead code now present in wcn36xx_smd_config_bss() and happily remove one
kzalloc from the BSS config path as we do so.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-8-bryan.odonoghue@linaro.org
A previous patch added wcn36xx_smd_config_bss_v0() this patch converts the
version 0 data-path in wcn36xx_smd_config_bss() to use
wcn36xx_smd_config_bss_v0().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-7-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_config_bss_v0() as a step along the road of
functionally decomposing wcn36xx_smd_config_bss().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-6-bryan.odonoghue@linaro.org
This patch updates wcn36xx_smd_config_bss_v1() to update on internally
derived parameters only, specifically making use of STA v1 wrapper routines
previously added.
Once done we no longer need to pass a struct wcn36xx_hal_config_bss_req_msg
which gives us options in later patches to eliminate the kzalloc() in
wcn36xx_smd_config_bss entirely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-5-bryan.odonoghue@linaro.org
This commit moves BSS parameter setup to a separate function
wcn36xx_smd_set_bss_params(). This will allow for further functional
decomposition and fewer kzalloc() operations in subsequent patches.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-4-bryan.odonoghue@linaro.org
In order to facilitate functional decomposition of
wcn36xx_smd_config_bss() we need to move wcn36xx_smd_set_sta_params() later
in function.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-3-bryan.odonoghue@linaro.org
This commit functionally decomposes wcn36xx_smd_config_sta into a clearly
defined wcn36xx_smd_config_sta_v0 and wcn36xx_smd_config_sta_v1 path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-2-bryan.odonoghue@linaro.org
This commit adds a wrapper function wcn36xx_smd_set_sta_params_v1() which
calls into wcn36xx_smd_set_sta_params() and then subsequently sets
version-1 specific parameters.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-8-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_set_bss_vht_params(). The job of this function
is to decide if the BSS is VHT capable and if so set the appropriate bit
in the BSS parameter structure for passing to the firmware.
VHT Channel width set is not set since we don't support 160MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-7-bryan.odonoghue@linaro.org
Adds a routine to allow setting the LDPC bit for HT parameter passing
inside the version 1 STA parameters data structure.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-6-bryan.odonoghue@linaro.org
This commit adds support for setting VHT parameters based on the declared
VHT capability bits in the VHT capability structure.
We cannot do 160MHz so VHT Channel width set should be zero.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-5-bryan.odonoghue@linaro.org
Toggling the LDPC enabled bit is possible only via the extended V1
data-structure. This function provides a means of setting the default
depending on chip-type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-4-bryan.odonoghue@linaro.org
This commit adds support for setting default VHT parameters, which are
exposed by the extended version 1 STA parameter type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-3-bryan.odonoghue@linaro.org
This patch converts the internal data structure used to store data-rates
from version 0 to version 1.
This allows us to extend out the internal storage to represent VHT
parameters.
Using the extended version 1 data-structure allows us to avoid a whole raft
of version 1 specific fixup functions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-3-bryan.odonoghue@linaro.org
In order to pass VHT parameters to wcn3680 we need to use a super-set of
the V1 data-structures with additional VHT parameters tacked on.
This patch adds the additional fields to the STA and BSS parameter
structures.
Since neither wcn3620 nor wcn3660 support VHT the size of the passed
message is fixed to the previous message length. Subsequent changes will
differentiate between wcn3620/wcn3660 and wcn3680 which does use the larger
message size.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-2-bryan.odonoghue@linaro.org
In order for the firmware to process extended V1 parameters with the
addtional VHT fields added we need to first enable the feature bit DOT11AC.
Once done the version number in the HAL message header will be acted upon
by the firmware.
Extended V1 parameters are a prerequisite for 802.11ac speeds since we
cannot communicate VHT parameters to the firmware absent the extended data
structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-11-bryan.odonoghue@linaro.org
Two pointers are already defined in this function "bss" and "sta" which
point to fields within msg_body->bss_params.
We can substantially reduce the amount of extraneous text in this function
by making use of those pointers. This change makes the code easier to read
and modify.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-10-bryan.odonoghue@linaro.org
Specify the number of spatial streams in ieee80211_rx_status. For non VHT
data-rates the wireless core doesn't care about this field, however for VHT
data-rates it does.
Every version of wcn36xx has one spatial stream, so specify nss for
wcn3620, wcn3660 and wcn3680 now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-7-bryan.odonoghue@linaro.org
The rate_idx is the index of the bitrate in the supported rate table.
However the 5Ghz band has a smaller legacy bitrate table than 2.4Ghz
since it does not have the DSSS bitrates (1, 2, 5.5, 11).
So in 5Ghz band the index should adjusted accrodingly (-4).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[bod: Made sure fix is only applied if the rate_idx > n_bitrates]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-6-bryan.odonoghue@linaro.org
If DT indicates we are dealing with a WCN3680 mark the rf_id field as
RF_IRIS_WCN3680 allowing for further chip-specific logic.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-3-bryan.odonoghue@linaro.org
The WCN3680 has some specific behaviours that we want to capture to
distinguish it from the WCN3620 and WCN3660 respectively.
Add an identifier for this purpose.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-2-bryan.odonoghue@linaro.org
For whatever reason, when connected to an open/no-security BSS,
the wcn36xx controller in bmps mode does not forward 'wake-up'
beacons despite AP sends DTIM with station AID.
Meaning that AP is not able to wakeup the station and needs to wait
for the station to wakeup by its own (TX data, keep alive pkt...),
causing serious latency issues and unexpected deauth.
When connected to AP with encryption enabled, this issue does not occur.
So a simple workaround is to only enable bmps support in that case.
Ideally, it should be propertly fixed to allow bmps support with open
BSS, whatever the issue is at driver or firmware level.
Tested on wcn3620 and wcn3680.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598363127-26066-1-git-send-email-loic.poulain@linaro.org
By default, after associated to an AP, the wcn36xx bitrate adjustment
algorithm starts sending data at 1Mbps, and increases the rate slowly
(1Mbps, 2Mbps, 6Mbps...) over the further TX packets.
Starting at 1Mbps usually causes the initial throughput to be really
low and the maximum possible bitrate to be reached after about hundreed
of TX packets.
That can be improved by setting a different initial bitrate for data
packets via the ENABLE_DYNAMIC_RA_START_RATE configuration value, this
value can be a legacy or MCS rate.
This patch sets the starting bitrate value to MCS-5, which seems to be
a good compromise given it can be quickly adjusted low or up if necessary.
(and based on what I observed in the wild with some mobile devices)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598345341-4505-1-git-send-email-loic.poulain@linaro.org
For software-driven scan, rely on mac80211 software scan instead
of internal driver implementation. The internal implementation
cause connection trouble since it keep the antenna busy during
the entire scan duration, moreover it's only a passive scanning
(no probe request). Therefore, let mac80211 manages sw scan.
Note: we fallback to software scan if firmware does not report
scan offload support or if we need to scan the 5Ghz band (currently
not supported by the offload scan...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598288035-19790-1-git-send-email-loic.poulain@linaro.org
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.
This patch fixes the data-rate declared in the 5GHz table.
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
