IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ath10k_sta_statistics is used to report info for iw wlan0 link,
it check ath10k_peer_stats_enabled, and ath10k_peer_stats_enabled
check WMI_SERVICE_PEER_STATS bit of ar->wmi.svc_map. SVCMAP() for
WMI_SERVICE_PEER_STATS was defined only for wmi_10x_svc_map and
wmi_10_4_svc_map interfaces, it missed in wmi_tlv_svc_map, so it is
not usable for iw wlan0 link for wmi tlv interface.
If firmware report WMI_TLV_SERVICE_PEER_STATS_INFO for wmi tlv, then
enable the WMI_SERVICE_PEER_STATS bit in ath10k, and then it pass check
in ath10k_peer_stats_enabled and ath10k_sta_statistics pass check.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-2-git-send-email-wgong@codeaurora.org
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719104041.57916-1-grandmaster@al2klimov.de
list_for_each_entry{_safe} is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry{_safe} is defined in terms of
list_first_entry, which indicates that it should not be used on an
empty list. But in list_for_each_entry{_safe}, the element obtained
by list_first_entry is not really accessed, only the address of its
list_head field is compared to the address of the list head, so the
list_first_entry is safe.
The semantic patch that makes this change for the list_for_each_entry
case is as follows: (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each_entry(i,x,...) S
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595761112-11003-8-git-send-email-Julia.Lawall@inria.fr
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
Typo "destoy" made me wonder if correct patch is wrong; fix it. No
functional change.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724083910.GA31930@amd
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719105052.57997-1-grandmaster@al2klimov.de
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfGukwAAoJEG4XJFUm622bIdwIAKYV3lplb6mXyDdF1b3Yoxar
0IDUglXlJN+VIgvUQG4wOvxgDw7jp6q95BRi58VjafIFm+orjILvYFmwThLPYfIS
dA0ML9+zGnRMC+SIjZktXKG9lridQXyqexWHCFF9dT147GsF8+LIbfqT6denCLf7
vP26RSMAMK5Ed01V9qb5rtitaVbr+Bx+c7adV8tLH/gkWeTEp4CaDhNOkMJ0uRCV
QPZ8duF1Hz/QVMn9PAA8xGTH4bxIfSfWVJfSjG1uq349CZ+MjHleDeYWKh524ThV
49YTabR2DIKOWSgNzG7jsitz7K/420Y/NpuNeGWO+7czgYe2uEIrGDZkYPUPoS4=
=PTR1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfFWQeAAoJEG4XJFUm622bVAwH/3r2oR+NS1kNDNGi9nrLAIav
trLgPa2VbgPVgTcwIckfvZFl6BK9zo1KG6u6jYp45C6uNBJNESjarf8aLAXvXdFt
t0yBkb6OCUq+efoOFbxV2im6ER57aN27POsn74xrCeR3fwZgY9QSHRMjQ5x1tjWH
JdVatT6jtu2LuxsTjfS0K5kjeuyE0vE1iCUlsQ5qwcSLODGa9u7ydheoNcLOHvss
ACun8zXvWqJhTar+iJHiTJTWyQPE6es0V1SAw0RnTuLRRmtv/Q9Zx4YOH2d3JkOC
55mfgO3uNzw8fcJ5hoILHtXxhI2qtSkdydIFbE1U9CgBKE39Uo0VgFf9fl6VJRg=
=7a5a
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
[ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0
[ 15.595483] #PF: supervisor write access in kernel mode
[ 15.596250] #PF: error_code(0x0002) - not-present page
[ 15.597013] PGD 0 P4D 0
[ 15.597395] Oops: 0002 [#1] SMP KASAN PTI
[ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 #69
[ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
[ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n
(linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-2-refactormyself@gmail.com
This fix allows ath9k_htc modules to connect to WLAN once again.
Fixes: 2bbcaaee1fcb ("ath9k: Fix general protection fault in ath9k_hif_usb_rx_cb")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208251
Signed-off-by: Mark O'Donovan <shiftee@posteo.net>
Reported-by: Roman Mamedov <rm@romanrm.net>
Tested-by: Viktor Jägersküpper <viktor_jaegerskuepper@freenet.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200711043324.8079-1-shiftee@posteo.net
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands. In this case, too, the non-gro path didn't bother checking
the return value. Plus, this had some clunky debugging functions that
duplicated code from elsewhere and was generally pretty messy. So, this
commit cleans that all up too.
Fixes: 6570bc79c0df ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org
To avoid duplicating the logic how the full firmware path is created create a
common function ath11k_core_firmware_request() and convert also qmi.c to use it.
Also remove a useless info print, it's more like a debug message anyway.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-7-git-send-email-kvalo@codeaurora.org
pdev_id to hw_mac is different for ipq8074 and ipq6018
Below table has the mapping
pdev_id ipq8074 ipq6018
------- ------- -------
0 0 0
1 2 1
2 1 Not applicable
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-5-git-send-email-kvalo@codeaurora.org
Convert to ath11k_hw_params to an array to make it possible add new hardware in
the future, for example IPQ6018 or QCA6390.
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-3-git-send-email-kvalo@codeaurora.org
A compromized ath10k peripheral is able to control the size argument
of memcpy in ath10k_pci_hif_exchange_bmi_msg.
The min result from previous line is not used as the size argument
for memcpy. Instead, xfer.resp_len comes from untrusted stream dma
input. The value comes from "nbytes" in ath10k_pci_bmi_recv_data,
which is set inside _ath10k_ce_completed_recv_next_nolock with the line
nbytes = __le16_to_cpu(sdesc.nbytes);
sdesc is a stream dma region which device can write to.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616132544.17478-1-bruceshenzk@gmail.com
We need this so that all hardware versions can coexist and
it's easier to manage everything then all hardware
directories are under ath11k directory.
Copy ath11k firmware files to
/lib/firmware/ath11k/IPQ8074/hw2.0/
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591709581-18039-3-git-send-email-akolli@codeaurora.org
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140
Fixes: fa7937e3d5c2 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
When tx status enabled, retry count is updated from tx completion status.
which is not working as expected due to firmware limitation where
firmware can not provide per MSDU rate statistics from tx completion
status. Due to this tx retry count is always 0 in station dump.
Fix this issue by updating the retry packet count from per peer
statistics. This patch will not break on SDIO devices since, this retry
count is already updating from peer statistics for SDIO devices.
Tested-on: QCA9984 PCI 10.4-3.6-00104
Tested-on: QCA9882 PCI 10.2.4-1.0-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591856446-26977-1-git-send-email-vnaralas@codeaurora.org
On wcn3990 we have "per_ce_irq = true". That makes the
ath10k_ce_interrupt_summary() function always return 0xfff. The
ath10k_ce_per_engine_service_any() function will see this and think
that _all_ copy engines have an interrupt. Without checking, the
ath10k_ce_per_engine_service() assumes that if it's called that the
"copy complete" (cc) interrupt fired. This combination seems bad.
Let's add a check to make sure that the "copy complete" interrupt
actually fired in ath10k_ce_per_engine_service().
This might fix a hard-to-reproduce failure where it appears that the
copy complete handlers run before the copy is really complete.
Specifically a symptom was that we were seeing this on a Qualcomm
sc7180 board:
arm-smmu 15000000.iommu: Unhandled context fault:
fsr=0x402, iova=0x7fdd45780, fsynr=0x30003, cbfrsynra=0xc1, cb=10
Even on platforms that don't have wcn3990 this still seems like it
would be a sane thing to do. Specifically the current IRQ handler
comments indicate that there might be other misc interrupt sources
firing that need to be cleared. If one of those sources was the one
that caused the IRQ handler to be called it would also be important to
double-check that the interrupt we cared about actually fired.
Tested-on: WCN3990 SNOC WLAN.HL.3.2.2-00490-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200609082015.1.Ife398994e5a0a6830e4d4a16306ef36e0144e7ba@changeid
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
