IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside the function lan8814_config_intr, there are double spaces when
assigning the return value of phy_write to err.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220921065444.637067-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ece19502834d ("net: phy: micrel: 1588 support for LAN8814
phy") the handler always returns IRQ_HANDLED, except in an error case.
Before that commit, the interrupt status register was checked and if
it was empty, IRQ_NONE was returned. Restore that behavior to play nice
with the interrupt line being shared with others.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <Divya.Koppera@microchip.com>
Link: https://lore.kernel.org/r/20220920141619.808117-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for interrupts for LAN8804 PHY.
Tested-by: Michael Walle <michael@walle.cc> # on kontron-kswitch-d10
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220913142926.816746-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a quirk for the HALNy HL-GSFP module, which appears to have an
inverted RX_LOS signal, and maybe uses TX_FAULT as a serial port
transmit pin. Rather than use these hardware signals, switch to
using software polling for these status signals.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move this module over to the new fixup mechanism.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new fixup mechanism to the SFP quirks, and use it for this
module.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to handle more quirks than just those which affect the link
modes of the module. Move the quirk lookup into sfp.c, and pass the
quirk to sfp-bus.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Re-implement the decision making for soft state polling. Instead of
generating the soft state mask in sfp_soft_start_poll() by looking at
which GPIOs are available, record their availability in
sfp_sm_mod_probe() in sfp->state_hw_mask.
This will then allow us to clear bits in sfp->state_hw_mask in module
specific quirks when the hardware signals should not be used, thereby
allowing us to switch to using the software state polling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional PHY IDs for the internal PHYs of adin1110 and adin2111.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch switches the driver away from legacy gpio/of_gpio API to
gpiod API, and removes use of of_get_named_gpio_flags() which I want to
make private to gpiolib.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220906204922.3789922-3-dmitry.torokhov@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Aquantia datasheet notes that after issuing a Processor-Intensive
MDIO operation, like changing the low-power state of the device, the
driver should wait for the operation to finish before issuing a new MDIO
command.
The new aqr107_wait_processor_intensive_op() function is added which can
be used after these kind of MDIO operations. At the moment, we are only
adding it at the end of the suspend/resume calls.
The issue was identified on a board featuring the AQR113C PHY, on
which commands like 'ip link (..) up / down' issued without any delays
between them would render the link on the PHY to remain down.
The issue was easy to reproduce with a one-liner:
$ ip link set dev ethX down; ip link set dev ethX up; \
ip link set dev ethX down; ip link set dev ethX up;
Fixes: ac9e81c230eb ("net: phy: aquantia: add suspend / resume callbacks for AQR107 family")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220906130451.1483448-1-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d52 ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently phy link up/down interrupt is enabled using the
LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function,
phy link is determined using the T1_MODE_STAT_REG register comm_ready bit.
comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status.
Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set
first but comm_ready bit takes some time to set based on local and
remote receiver status.
As per the current implementation, interrupt is triggered using link_up
but the comm_ready bit is still cleared in the read_status function. So,
link is always down. Initially tested with the shared interrupt
mechanism with switch and internal phy which is working, but after
implementing interrupt controller it is not working.
It can fixed either by updating the read_status function to read from
LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for
comm_ready bit. But the validation team recommends the use of comm_ready
for link detection.
This patch fixes by enabling the comm_ready bit for link_up in the
LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in
LAN87xx_INTERRUPT_MASK register.
Fixes: 8a1b415d70b7 ("net: phy: added ethtool master-slave configuration support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220905152750.5079-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add 1000BASE-KX interface mode. This 1G backplane ethernet as described in
clause 70. Clause 73 autonegotiation is mandatory, and only full duplex
operation is supported.
Although at the PMA level this interface mode is identical to
1000BASE-X, it uses a different form of in-band autonegation. This
justifies a separate interface mode, since the interface mode (along
with the MLO_AN_* autonegotiation mode) sets the type of autonegotiation
which will be used on a link. This results in more than just electrical
differences between the link modes.
With regard to 1000BASE-X, 1000BASE-KX holds a similar position to
SGMII: same signaling, but different autonegotiation. PCS drivers
(which typically handle in-band autonegotiation) may only support
1000BASE-X, and not 1000BASE-KX. Similarly, the phy mode is used to
configure serdes phys with phy_set_mode_ext. Due to the different
electrical standards (SFI or XFI vs Clause 70), they will likely want to
use different configuration. Adding a phy interface mode for
1000BASE-KX helps simplify configuration in these areas.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2c87c6f9fbddc5b84d67b2fa3f432fcac6d99d93.
Meanwhile it turned out that the following commit is the proper
workaround for the issue that 2c87c6f9fbdd tries to address.
a3a57bf07de2 ("net: stmmac: work around sporadic tx issue on link-up")
It's nor clear why the to be reverted commit helped for one user,
for others it didn't make a difference.
Fixes: 2c87c6f9fbdd ("net: phy: meson-gxl: improve link-up behavior")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8deeeddc-6b71-129b-1918-495a12dc11e3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b09250ee ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As per RGMII specification v2.0, section 3.4.1, RGMII/RTBI has an
optional in-band status feature where the PHY's link status, speed and
duplex mode can be passed to the MAC.
Allow RGMII/RTBI to use in-band status.
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add below features support for both TJA1100 and TJA1101 cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For some MAC drivers, they set the mac_managed_pm to true in its
->ndo_open() callback. So before the mac_managed_pm is set to true,
we still want to leverage the mdio_bus_phy_suspend()/resume() for
the phy device suspend and resume. In this case, the phy device is
in PHY_READY, and we shouldn't warn about this. It also seems that
the check of mac_managed_pm in WARN_ON is redundant since we already
check this in the entry of mdio_bus_phy_resume(), so drop it.
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220819082451.1992102-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some phy modes such as QSGMII multiplex several MAC<->PHY links on one
single physical interface. QSGMII used to be the only one supported, but
other modes such as QUSGMII also carry multiple links.
This helper allows getting the number of links that are multiplexed
on a given interface.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QUSGMII mode is a derivative of Cisco's USXGMII standard. This
standard is pretty similar to SGMII, but allows for faster speeds, and
has the build-in bits for Quad and Octa variants (like QSGMII).
The main difference with SGMII/QSGMII is that USXGMII/QUSGMII re-uses
the preamble to carry various information, named 'Extensions'.
As of today, the USXGMII standard only mentions the "PCH" extension,
which is used to convey timestamps, allowing in-band signaling of PTP
timestamps without having to modify the frame itself.
This commit adds support for that mode. When no extension is in use, it
behaves exactly like QSGMII, although it's not compatible with QSGMII.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211F(D)(I)-VD-CG is the pin-to-pin upgrade chip from
RTL8211F(D)(I)-CG.
Add new PHY ID for this chip.
It does not support RTL8211F_PHYCR2 anymore, so remove the w/r operation
of this register.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the cable is unplugged, the Atheros AR803x PHYs will enter
hibernation mode after about 10 seconds if the hibernation mode
is enabled and will not provide any clock to the MAC. But for
some MACs, this feature might cause unexpected issues due to the
logic of MACs.
Taking SYNP MAC (stmmac) as an example, if the cable is unplugged
and the "eth0" interface is down, the AR803x PHY will enter
hibernation mode. Then perform the "ifconfig eth0 up" operation,
the stmmac can't be able to complete the software reset operation
and fail to init it's own DMA. Therefore, the "eth0" interface is
failed to ifconfig up. Why does it cause this issue? The truth is
that the software reset operation of the stmmac is designed to
depend on the RX_CLK of PHY.
So, this patch offers an option for the user to determine whether
to disable the hibernation mode of AR803x PHYs.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the suspend/resume procedure for the Broadcom AC131 and BCM5241 type
of PHYs (10/100 only) by entering the standard power down followed by the
proprietary standby mode in the auxiliary mode 4 shadow register. On resume,
the PHY software reset is enough to make it come out of standby mode so we can
utilize brcm_fet_config_init() as the resume hook.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NVMEM is not set of_nvmem_cell_get, of_nvmem_device_get
functions will return ERR_PTR(-EOPNOTSUPP) and "failed to get nvmem
cell io_impedance_ctrl" error would be reported despite "io_impedance_ctrl"
is completely missing in Device Tree and we should use default values.
Check -EOPNOTSUPP togather with -ENOENT to avoid this situation.
Fixes: 5c2d0a6a0701 ("net: phy: dp83867: implement support for io_impedance_ctrl nvmem cell")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805084843.24542-1-nikita.shubin@maquefel.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case master/slave clock role is not specified (which is default), the
aneg registers will not be written.
The visible impact of this is missing pause advertisement.
So, rework genphy_c45_baset1_an_config_aneg() to be able to write
advertisement registers even if clock role is unknown.
Fixes: 3da8ffd8545f ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805073159.908643-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling mdio_bus_phy_resume() with neither the PHY state machine set to
PHY_HALTED nor phydev->mac_managed_pm set to true is a good indication
that we can produce a race condition looking like this:
CPU0 CPU1
bcmgenet_resume
-> phy_resume
-> phy_init_hw
-> phy_start
-> phy_resume
phy_start_aneg()
mdio_bus_phy_resume
-> phy_resume
-> phy_write(..., BMCR_RESET)
-> usleep() -> phy_read()
with the phy_resume() function triggering a PHY behavior that might have
to be worked around with (see bf8bfc4336f7 ("net: phy: broadcom: Fix
brcm_fet_config_init()") for instance) that ultimately leads to an error
reading from the PHY.
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220801233403.258871-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now having a major and a minor number, also print the firmware in
human readable form "major.minor". Still keep the 4-digit hexadecimal
representation because that form is used in the firmware changelog
documents. Also, drop the "release" string assuming that most common
case, but make it clearer that the user is running a test version.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the firmware field name with the reference manual where it is
called "major".
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache the firmware version during probe. There is no need to read the
firmware version on every autonegotiation.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 09ce6b20103b ("net: phy: mxl-gpy: add temperature sensor")
will overwrite the return value and the reported version will be wrong.
Fix it.
Fixes: 09ce6b20103b ("net: phy: mxl-gpy: add temperature sensor")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are operating in SGMII inband mode, it implies that there is a
PHY connected, and the ethtool advertisement for autoneg applies to
the PHY, not the SGMII link. When in 1000base-X mode, then this applies
to the 802.3z link and needs to be applied to the PCS.
Fix this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1o9Ng2-005Qbe-3H@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for BCM53128 internal PHYs. These support interrupts as well as
statistics. Therefore, enable the Broadcom PHY driver for them.
Tested on BCM53128 switch using the mainline b53 DSA driver.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED support for extended mode where
LED 1: Enhanced Mode 5 (10M/1000M/Activity)
LED 2: Enhanced Mode 4 (100M/1000M/Activity)
By default it supports KSZ9031 LED mode
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1db ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e33a ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current link mode of the phylink instance may not require an
attached PCS. However, phylink_major_config() unconditionally
dereferences this potentially NULL pointer when restarting the link poll
timer, which will panic the kernel.
Fix the problem by checking whether a PCS exists in phylink_pcs_poll_start(),
otherwise do nothing. The code prior to the blamed patch also only
looked at pcs->poll within an "if (pcs)" block.
Fixes: bfac8c490d60 ("net: phylink: disable PCS polling over major configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Tested-by: Michael Walle <michael@walle.cc> # on kontron-kbox-a-230-ls
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com> # on sam9x60ek
Link: https://lore.kernel.org/r/20220629193358.4007923-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sfp_probe() allocates a memory chunk from sfp with sfp_alloc(). When
devm_add_action() fails, sfp is not freed, which leads to a memory leak.
We should use devm_add_action_or_reset() instead of devm_add_action().
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220629075550.2152003-1-niejianglei2021@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In case of asix_ax88772a_link_change_notify() workaround, we run soft
reset which will automatically clear MII_ADVERTISE configuration. The
PHYlib framework do not know about changed configuration state of the
PHY, so we need use phy_init_hw() to reinit PHY configuration.
Fixes: dde258469257 ("net: usb/phy: asix: add support for ax88772A/C PHYs")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220628114349.3929928-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00a4 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While we are performing a major configuration, there is no point having
the PCS polling timer running. Stop it before we begin preparing for
the configuration change, and restart it only once we've successfully
completed the change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the pcs_ops member from struct phylink, using the one stored in
struct phylink_pcs instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some RX errors, notably when disconnecting the cable, increase the RCSR
register. Once half full (0x7fff), an interrupt flood is generated. I
measured ~3k/s interrupts even after the RX errors transfer was
stopped.
Since we don't read and clear the RCSR register, we should disable this
interrupt.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
