IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The MediaTek Hardware ECC Engine is only present on MediaTek MT27xx and
MT76xx SoCs. The driver for this engine is a dependency for the
MediaTek NAND controller (MTD_NAND_MTK) and the MediaTek SPI NAND Flash
Interface (SPI_MTK_SNFI) drivers, both of which already depend on
ARCH_MEDIATEK.
Hence add a dependency on ARCH_MEDIATEK to the Hardware ECC Engine
driver, too, to prevent asking the user about this driver when
configuring a kernel without MediaTek SoC support.
Fixes: 4fd62f15afa0d0da ("mtd: nand: make mtk_ecc.c a separated module")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/bb9568e825d4bc7506870b03836baa91bcc4b725.1652104136.git.geert+renesas@glider.be
Add timings for Kioxia/Toshiba TH58NVG3S0HBAI4. Timings
for this memory matches the timings selected for
TH58NVG2S3HBAI4.
This patch increases eraseblock write speed from 5248 KiB/s
to 6864 KiB/s and erase block read speed from 8542 KiB/s
to 18360 KiB/s
Tested on i.MX6SX.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220429083931.26795-1-rickaran@axis.com
The intention was to print the JEDEC ID in the following format:
nn nn nn
In this case format specifier has to be "%*ph". Fix it.
Fixes: 0257be79fc4a ("mtd: spi-nor: expose internal parameters via debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220512112027.3771734-1-michael@walle.cc
This patch allows accessing the upper 16m on the A variant (EN25QH256A) of
the EN25QH256 that shares same JEDEC ID.
Without this patch, addr_with is detected to be '4' but the read_opcode is
a plain READ (supporting only 3 byte addresses).
Setting PARSE_SFDP is enough to detect the read_opcode READ_4B on the A
variant. READ_4B is not available on the no-A variant.
Both variants support 4-byte address mode (spi_nor_set_4byte_addr_mode)
but that is prone to breaking on unexpected reboots if the reset pin isn't
connected (broken-flash-reset).
The no-A variant supports a 'high bank latch mode' that affects read,
program, and erase commands - similar to the extended address register
(EAR).
The HBL bit is manipulated using the ENHBL (0x67) and EXHBL (0x98)
opcodes.
Should it become necessary to distinguish the two variants in the future,
the A variant sets the SNOR_HWCAPS_READ_1_1_4 SFDP param - the no-A
variant doesn't.
Tested with and without fast read on the A variant only.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220502233310.791565-2-leon@georgemail.eu
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
The rdsr dummy cycles are only used by the 8d-8d-8d mode. Mention that
in the documentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112837.2792242-1-michael@walle.cc
Since commit dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to
check correct value") buffered writes fail on S29GL064N. This is
because, on S29GL064N, reads return 0xFF at the end of DQ polling for
write completion, where as, chip_good() check expects actual data
written to the last location to be returned post DQ polling completion.
Fix is to revert to using chip_good() for S29GL064N which only checks
for DQ lines to settle down to determine write completion.
Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Cc: stable@vger.kernel.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-3-ikegami.t@gmail.com
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmJpa+MACgkQJWrqGEe9
VoTVPwf+PjOPS9MH+3wQkEsqwHtJyC9dvfTRWNSkzJEos0710jl6peeWjo1ift1A
4JLMI3TGHWbNqBykpSLxZPVc6X/toGoMz6/2OussnYQBYgXjLNOgWQqS4kZZmK7D
BARpke8TTqglJyat7NpGNo1EGWA4EtYqwvoPT+H0LMLQbe/NQD0k4RaRNpw+BwPq
gaBHZf/CmN4oG0QrPPvS7jrm0dgWrQgTqRf9zzOnml3m22q3PGMnmY1A1CunBsFn
HK+GxYUOeemPc40mET+U1x6O0+VNlxW2KQ+fZoNHnljd55zq1Cp4mXfr7KuFgfDK
4xMAAoI5cMp8kpLLVUBlD4uzOj3fow==
=FBXD
-----END PGP SIGNATURE-----
Merge tag 'mtd/mtk-spi-nand-for-5.19' into nand/next
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The recently added ECC engine support introduced a generic property
named nand-ecc-engine for ecc engine phandle. This patch adds support
for this new property.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-4-gch981213@gmail.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-2-yangyingliang@huawei.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
Writing volatile registers are instant according to Micron and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-12-tudor.ambarus@microchip.com
Writing volatile registers are instant according to Cypress and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-11-tudor.ambarus@microchip.com
Clean the op declaration and hide the details of each op. With this it
results a cleanner, easier to read code. No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420103427.47867-10-tudor.ambarus@microchip.com
Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com
Introduce template operation to remove code duplication.
Split spi_nor_micron_octal_dtr_enable() in spi_nor_micron_octal_dtr_en()
and spi_nor_micron_octal_dtr_dis() as it no longer made sense to try to
keep everything alltogether: too many "if (enable)" throughout the code,
which made the code difficult to follow. Add dev_dbg messages in case
spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-8-tudor.ambarus@microchip.com
There are manufacturers that use registers indexed by address. Some of
them support "read/write any register" opcodes. Provide core methods that
can be used by all manufacturers. SPI NOR controller ops are intentionally
not supported as we intend to move all the SPI NOR controller drivers
under the SPI subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-7-tudor.ambarus@microchip.com
Use spi_nor_read_id() core method to avoid duplication of code. Now the ID
is read on the full SPI_NOR_MAX_ID_LEN instead of
round_up(nor->info->id_len, 2), but it doesn't harm to read more ID bytes,
so the change comes with no secondary effects. dev_dbg messages in case
spi_nor_read_id() fails, will be added in a further patch after we split
the octal DTR enable/disable methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-6-tudor.ambarus@microchip.com
RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com
In case spi_nor_match_name() returned NULL, the auto detection was
issued twice. There's no reason to try to detect the same chip twice,
do the auto detection only once.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-4-tudor.ambarus@microchip.com
Similar to spi_nor_match_name() extend the search of flash_info through
all the manufacturers, this time doing the match by ID. There's no reason
to limit the search per manufacturer yet, do it globally, search the flash
in all the parts of all manufacturers in a single method.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-3-tudor.ambarus@microchip.com
The method is matching a flash_info entry by searching by name. Rename
the method for better clarity.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-2-tudor.ambarus@microchip.com
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
Create a dump header to enable the addition of fields without having
to modify the rest of the code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220421234244.2172003-3-jmeurin@google.com
The read buffer size depends on the MTDOOPS_HEADER_SIZE.
Tested: Changed the header size, it doesn't panic, header is still
read/written correctly.
Signed-off-by: Jean-Marc Eurin <jmeurin@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220421234244.2172003-2-jmeurin@google.com
Warning on every translated mtd partition results in excessive log noise
if this driver is loaded:
nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
nand: Macronix MX30LF1G18AC
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
read_bbt: found bbt at block 1023
10 fixed-partitions partitions found on MTD device mt7621-nand
Creating 10 MTD partitions on "mt7621-nand":
0x000000000000-0x000000080000 : "Bootloader"
mtdblock: MTD device 'Bootloader' is NAND, please consider using UBI block devices instead.
0x000000080000-0x000000100000 : "Config"
mtdblock: MTD device 'Config' is NAND, please consider using UBI block devices instead.
0x000000100000-0x000000140000 : "Factory"
mtdblock: MTD device 'Factory' is NAND, please consider using UBI block devices instead.
0x000000140000-0x000002000000 : "Kernel"
mtdblock: MTD device 'Kernel' is NAND, please consider using UBI block devices instead.
0x000000540000-0x000002000000 : "ubi"
mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
0x000002140000-0x000004000000 : "Kernel2"
mtdblock: MTD device 'Kernel2' is NAND, please consider using UBI block devices instead.
0x000004000000-0x000004100000 : "wwan"
mtdblock: MTD device 'wwan' is NAND, please consider using UBI block devices instead.
0x000004100000-0x000005100000 : "data"
mtdblock: MTD device 'data' is NAND, please consider using UBI block devices instead.
0x000005100000-0x000005200000 : "rom-d"
mtdblock: MTD device 'rom-d' is NAND, please consider using UBI block devices instead.
0x000005200000-0x000005280000 : "reserve"
mtdblock: MTD device 'reserve' is NAND, please consider using UBI block devices instead.
mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
This is more likely to annoy than to help users of embedded distros where
this driver is enabled by default. Making the blockdevs available does
not imply that they are in use, and warning about bootloader partitions
or other devices which obviously never will be mounted is more confusing
than helpful.
Move the warning to open(), where it will be of more use - actually warning
anyone who mounts a file system on NAND using mtdblock.
Fixes: e07403a8c6be ("mtdblock: Warn if added for a NAND device")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220328161108.87757-1-bjorn@mork.no
Allow phram to be probed from the devicetree. It expects to be in a
reserved-memory node as documented by the bindings. This allows things
like partitioning to be specified via the devicetree.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-4-vincent.whitchurch@axis.com
Allow the MTD index to be specified via a devicetree alias, so that the
number does not just depend on probe order. This is useful to allow
pseudo-devices like phram to be optionally used on systems, without
having this affect the numbering of the real hardware MTD devices.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412135302.1682890-2-vincent.whitchurch@axis.com
This custom maps driver was never used with the device tree
enabled IXP4xx systems, which use the physmap add-on from
commit 2aba2f2a704d
("mtd: physmap_of: add a hook for Intel IXP4xx flash probing")
Since kernel v5.18-rc1 IXP4xx is only booting from the device
tree so drop this old driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220407210844.2489682-1-linus.walleij@linaro.org
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 bytes OOB. This adds a static NAND ID entry to correct this.
Tested on FRITZ!Box 7530 flashed with OpenWrt.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220420104034.6333-1-dev@aboehler.at
The code change proposes a new way to set bch geometry for large oob
NAND (oobsize > 1KB). In this case, previous implementation can NOT
guarantee the bad block mark always locates in data chunk, so we need a
new way to do it. The general idea is,
1.Try all ECC strength from the maximum ecc that controller can support
to minimum value required by NAND chip, any ECC strength makes the
BBM locate in data chunk can be eligible.
2.If none of them works, using separate ECC for meta, which will add
one extra ecc with the same ECC strength as other data chunks. This
extra ECC can guarantee BBM located in data chunk, also we need to
check if oob can afford it.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-6-han.xu@nxp.com
There is only one variable ecc_chunk_size in bch_geometry data
structure but two different field in BCH registers. The data0_size in
BCH_FLASH0LAYOUT0 and datan_size in BCH_FLASH0LAYOUT1 should have
dedicate variable since they might set to different values in some
cases. For instance, if need dedicate ecc for meta area, the data0_size
should be 0 rather than datan_size, but for all other cases, data0_size
still equals to datan_size and it won't bring any function change.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-5-han.xu@nxp.com
Add nand_ecc_is_strong_enough() check in gpmi_check_ecc() function to
make sure ecc strength can meet chip requirement.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-3-han.xu@nxp.com
The code change refactor the bch geometry setting function, which
doesn't change the default behavior, while user may choose to use chips
required minimum ecc strength by DT flag "fsl,use-minimum-ecc".
The default way to set bch geometry need to set the data chunk
size(step_size) larger than oob size to make sure BBM locates in data
chunk, then set the maximum ecc strength oob can hold. It always use
unbalanced ECC layout, which ecc0 will cover both meta and data0 chunk.
But the default bch setting is deprecated for large oobsize NAND
(oobsize >1KB), so in the patch set, there is a split commit that
introduces a new way to set bch geometry for large oob size NAND.
For all other cases,set the bch geometry by chip required strength and
step size, which uses the minimum ecc strength chip required. It can be
explicitly enabled by DT flag "fsl,use-minimum-ecc", but need to be
en/disabled in both u-boot and kernel at the same time.
Signed-off-by: Han Xu <han.xu@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-2-han.xu@nxp.com
All of the resources used by this driver has managed interfaces, so use
them. Otherwise we will get the following splat:
[ 4.472703] denali-nand-pci 0000:00:05.0: timeout while waiting for irq 0x1000
[ 4.474071] denali-nand-pci: probe of 0000:00:05.0 failed with error -5
[ 4.473538] nand: No NAND device found
[ 4.474068] BUG: unable to handle page fault for address: ffffc90005000410
[ 4.475169] #PF: supervisor write access in kernel mode
[ 4.475579] #PF: error_code(0x0002) - not-present page
[ 4.478362] RIP: 0010:iowrite32+0x9/0x50
[ 4.486068] Call Trace:
[ 4.486269] <IRQ>
[ 4.486443] denali_isr+0x15b/0x300 [denali]
[ 4.486788] ? denali_direct_write+0x50/0x50 [denali]
[ 4.487189] __handle_irq_event_percpu+0x161/0x3b0
[ 4.487571] handle_irq_event+0x7d/0x1b0
[ 4.487884] handle_fasteoi_irq+0x2b0/0x770
[ 4.488219] __common_interrupt+0xc8/0x1b0
[ 4.488549] common_interrupt+0x9a/0xc0
Fixes: 93db446a424c ("mtd: nand: move raw NAND related code to the raw/ subdir")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220411125808.958276-1-zheyuma97@gmail.com
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
