IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add KPP support to the crypto engine queue manager, so that it can be
used to simplify the logic of KPP device drivers as done for other
crypto drivers.
Signed-off-by: Prabhjot Khurana <prabhjot.khurana@intel.com>
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This swaps the descriptions of the 0 and 1 values to match
what the driver actually does with this property.
The background here is somewhat confusing. The codec has two
invert bits for the tip sense. The DT property should have been
for the TIP_SENSE_INV bit, which is the one that controls the
detect block. Due to some misunderstanding of the hardware the
driver actually implemented setting of the TS_INV bit, which is
only for swapping the sense of the interrupt bits. The description
was taken from the datasheet and refers to TIP_SENSE_INV but
unfortunately TS_INV has a different purpose and the net effect
of changing it is the reverse of what was intended (this is not
clearly described in the datasheet). So the ts-inv settings have
always done the exact opposite of what the description said.
Given the age of the driver, it's too late now to swap the meanings
of the values, so the description is changed to match the behaviour.
They have been annotated with the terminology used in the datasheet
to avoid the confusion of which one corresponds to what the datasheet
calls "inverted tip sense".
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: da16c5579353 ("ASoC: cs42l42: Add devicetree bindings for CS42L42")
Link: https://lore.kernel.org/r/20211028140902.11786-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
* for-next/trbe-errata:
arm64: errata: Add detection for TRBE write to out-of-range
arm64: errata: Add workaround for TSB flush failures
arm64: errata: Add detection for TRBE overwrite in FILL mode
arm64: Add Neoverse-N2, Cortex-A710 CPU part definition
All SoCs with this IP core support 8 burst length. Hauke
suggested to hardcode this value and simplify the driver.
Link: https://lkml.org/lkml/2021/9/14/1533
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'enable_remote_dev_reset' documentation to bnxt.rst.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention the 'Link' tag in the section about adding URLs to the commit
msg, to make it clearer they "_primarily_ [...] should be about
background", as Linus recently stated (see the link below). That makes
the explanation also easier to find with a text search. For the same
reason and to improve comprehensibility provide an example, too.
Slightly improve the text at the same time to make it more obvious
developers are meant to add links to issue reports in mailing list
archives, as those allow regression tracking efforts to automatically
check which bugs got resolved.
Move the section also downwards slightly, to reduce jumping back and
forth between aspects relevant for the top and the bottom part of the
commit msg.
Link: https://lore.kernel.org/lkml/CAHk-=wgBhyLhQLPem1vybKNt7BKP+=qF=veBgc7VirZaXn4FUw@mail.gmail.com/
CC: Konstantin Ryabitsev <konstantin@linuxfoundation.org>
Signed-off-by: Thorsten Leemhuis <linux@leemhuis.info>
Reviewed-by: Konstantin Ryabitsev <konstantin@linuxfoundation.org>
Link: https://lore.kernel.org/r/27105768dc19b395e7c8e7a80d056d1ff9c570d0.1635152553.git.linux@leemhuis.info
[jc: tweaked wording following Konstantin's recommendation]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
(mac80211), and BPF.
Current release - regressions:
- skb_expand_head: adjust skb->truesize to fix socket memory
accounting
- mptcp: fix corrupt receiver key in MPC + data + checksum
Previous releases - regressions:
- multicast: calculate csum of looped-back and forwarded packets
- cgroup: fix memory leak caused by missing cgroup_bpf_offline
- cfg80211: fix management registrations locking, prevent list
corruption
- cfg80211: correct false positive in bridge/4addr mode check
- tcp_bpf: fix race in the tcp_bpf_send_verdict resulting in reusing
previous verdict
Previous releases - always broken:
- sctp: enhancements for the verification tag, prevent attackers
from killing SCTP sessions
- tipc: fix size validations for the MSG_CRYPTO type
- mac80211: mesh: fix HE operation element length check, prevent
out of bound access
- tls: fix sign of socket errors, prevent positive error codes
being reported from read()/write()
- cfg80211: scan: extend RCU protection in cfg80211_add_nontrans_list()
- implement ->sock_is_readable() for UDP and AF_UNIX, fix poll()
for sockets in a BPF sockmap
- bpf: fix potential race in tail call compatibility check resulting
in two operations which would make the map incompatible succeeding
- bpf: prevent increasing bpf_jit_limit above max
- bpf: fix error usage of map_fd and fdget() in generic batch update
- phy: ethtool: lock the phy for consistency of results
- prevent infinite while loop in skb_tx_hash() when Tx races with
driver reconfiguring the queue <> traffic class mapping
- usbnet: fixes for bad HW conjured by syzbot
- xen: stop tx queues during live migration, prevent UAF
- net-sysfs: initialize uid and gid before calling net_ns_get_ownership
- mlxsw: prevent Rx stalls under memory pressure
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=61p6
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from WiFi (mac80211), and BPF.
Current release - regressions:
- skb_expand_head: adjust skb->truesize to fix socket memory
accounting
- mptcp: fix corrupt receiver key in MPC + data + checksum
Previous releases - regressions:
- multicast: calculate csum of looped-back and forwarded packets
- cgroup: fix memory leak caused by missing cgroup_bpf_offline
- cfg80211: fix management registrations locking, prevent list
corruption
- cfg80211: correct false positive in bridge/4addr mode check
- tcp_bpf: fix race in the tcp_bpf_send_verdict resulting in reusing
previous verdict
Previous releases - always broken:
- sctp: enhancements for the verification tag, prevent attackers from
killing SCTP sessions
- tipc: fix size validations for the MSG_CRYPTO type
- mac80211: mesh: fix HE operation element length check, prevent out
of bound access
- tls: fix sign of socket errors, prevent positive error codes being
reported from read()/write()
- cfg80211: scan: extend RCU protection in
cfg80211_add_nontrans_list()
- implement ->sock_is_readable() for UDP and AF_UNIX, fix poll() for
sockets in a BPF sockmap
- bpf: fix potential race in tail call compatibility check resulting
in two operations which would make the map incompatible succeeding
- bpf: prevent increasing bpf_jit_limit above max
- bpf: fix error usage of map_fd and fdget() in generic batch update
- phy: ethtool: lock the phy for consistency of results
- prevent infinite while loop in skb_tx_hash() when Tx races with
driver reconfiguring the queue <> traffic class mapping
- usbnet: fixes for bad HW conjured by syzbot
- xen: stop tx queues during live migration, prevent UAF
- net-sysfs: initialize uid and gid before calling
net_ns_get_ownership
- mlxsw: prevent Rx stalls under memory pressure"
* tag 'net-5.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (67 commits)
Revert "net: hns3: fix pause config problem after autoneg disabled"
mptcp: fix corrupt receiver key in MPC + data + checksum
riscv, bpf: Fix potential NULL dereference
octeontx2-af: Fix possible null pointer dereference.
octeontx2-af: Display all enabled PF VF rsrc_alloc entries.
octeontx2-af: Check whether ipolicers exists
net: ethernet: microchip: lan743x: Fix skb allocation failure
net/tls: Fix flipped sign in async_wait.err assignment
net/tls: Fix flipped sign in tls_err_abort() calls
net/smc: Correct spelling mistake to TCPF_SYN_RECV
net/smc: Fix smc_link->llc_testlink_time overflow
nfp: bpf: relax prog rejection for mtu check through max_pkt_offset
vmxnet3: do not stop tx queues after netif_device_detach()
r8169: Add device 10ec:8162 to driver r8169
ptp: Document the PTP_CLK_MAGIC ioctl number
usbnet: fix error return code in usbnet_probe()
net: hns3: adjust string spaces of some parameters of tx bd info in debugfs
net: hns3: expand buffer len for some debugfs command
net: hns3: add more string spaces for dumping packets number of queue info in debugfs
net: hns3: fix data endian problem of some functions of debugfs
...
In some configurations, the BAM DMA controller is set up by a remote
processor and the local processor can simply start making use of it
without setting up the BAM. This is already supported using the
"qcom,controlled-remotely" property.
However, for some reason another possible configuration is that the
remote processor is responsible for powering up the BAM, but we are
still responsible for initializing it (e.g. resetting it etc). Add
a "qcom,powered-remotely" property to describe that configuration.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20211018102421.19848-2-stephan@gerhold.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a file to document devlink support for octeontx2
driver. Driver-specific parameters implemented by
AF, PF and VF drivers are documented.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explain how dynamic XSTATE features can be enabled via the
architecture-specific prctl() along with dynamic sigframe size and
first use trap handling.
Fix:
Documentation/x86/xstate.rst:15: WARNING: Title underline too short.
as reported by Stephen Rothwell <sfr@canb.auug.org.au>
Originally-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211026091157.16711-1-chang.seok.bae@intel.com
* irq/remove-handle-domain-irq-20211026:
: Large rework of the architecture entry code from Mark Rutland.
: From the cover letter:
:
: <quote>
: The handle_domain_{irq,nmi}() functions were oringally intended as a
: convenience, but recent rework to entry code across the kernel tree has
: demonstrated that they cause more pain than they're worth and prevent
: architectures from being able to write robust entry code.
:
: This series reworks the irq code to remove them, handling the necessary
: entry work consistently in entry code (be it architectural or generic).
: </quote>
MIPS: irq: Avoid an unused-variable error
irq: remove handle_domain_{irq,nmi}()
irq: remove CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: riscv: perform irqentry in entry code
irq: openrisc: perform irqentry in entry code
irq: csky: perform irqentry in entry code
irq: arm64: perform irqentry in entry code
irq: arm: perform irqentry in entry code
irq: add a (temporary) CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: nds32: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: arc: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: add generic_handle_arch_irq()
irq: unexport handle_irq_desc()
irq: simplify handle_domain_{irq,nmi}()
irq: mips: simplify do_domain_IRQ()
irq: mips: stop (ab)using handle_domain_irq()
irq: mips: simplify bcm6345_l1_irq_handle()
irq: mips: avoid nested irq_enter()
Signed-off-by: Marc Zyngier <maz@kernel.org>
Commit cea0f76a483d ("dt-bindings: phy: Add DT bindings for Xilinx ZynqMP
PSGTR PHY") clearly defines #phy-cells as 4. In past 5 cells were used by
it never went to upstream. That's why fix example by using only 4 cells
instead of 5.
Fixes: e7c7970a678d ("dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/a291be294dea6e580ad9acd436742a48b7cd00a2.1634539210.git.michal.simek@xilinx.com
Signed-off-by: Rob Herring <robh@kernel.org>
Convert bindings for NXP PN544 NFC driver to YAML syntax.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211017160210.85543-1-david@ixit.cz
Signed-off-by: Rob Herring <robh@kernel.org>
The dtschema version check works, but is not that clear when dtschema is
either not installed or not in the PATH. Add a separate check and
message if dt-doc-validate is not found.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Update the binding for ti-sysc interconnect target module driver to yaml
format.
Note that the old binding was never updated for the need to always specify
also the generic compatible "ti,sysc". This is needed for the auxdata
for platform clockdomain autoidle related functions.
Cc: Rob Herring <robh@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015113350.35830-1-tony@atomide.com
[robh: dedupe reg-names and clock-names entries]
Signed-off-by: Rob Herring <robh@kernel.org>
Sram regions node name describes the region of reserved memory and can
be names such as l3cache@1000. Permit numbers to be used as part of the
reserved memory node name.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20211012154833.14111-1-nm@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
The EAC1 release of the SME specification adds the FA64 feature which
requires enablement at higher ELs before lower ELs can use it. Document
what we require from higher ELs in our boot requirements.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211026111802.12853-1-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
* eDP support in DP sub-driver (for newer SoCs with native eDP output)
* dpu irq handling cleanup
* CRC support for making igt happy
* Support for NO_CONNECTOR bridges
* dsi: 14nm phy support for msm8953
* mdp5: support for msm8x53, sdm450, sdm632
* various smaller fixes and cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsH9EwcpqGNNRJeL99NvFFjHX3SUg+nTYu0dHG5U9+QuA@mail.gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF298ceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGIJYH/1rsEFQQ6caeQdy1
z9eFIe48DNM4l7bFk+qEj2UAbzPdahVJ299Mg5fW0n2CDemOc9/n0b9TxQ37YObi
mOzu0xwJVupIxkyFMPQSSc2q8aLm67NSpJy08DsmaNses5hSvu8x15RPHLQTybjt
SwtKns+jpCq79P1GWbrB5e5UkLb0VNoxNp4L1U4pMrYGcEkJUXbaxNY2V/JcXdM7
Vtn+qN0T/J6V6QVftv0t8Ecj3bjEnmL3kZHaTaNg3dGeKRpCGyHc5lcBQ0cNFG6t
vjZ9VbuhBzGI3TN2tHH5hpA1UXo7HPBBCwQqxF1jeGLGHULikYwZ3TAPWqL3QZqC
9cxr9SY=
=p75d
-----END PGP SIGNATURE-----
BackMerge tag 'v5.15-rc7' into drm-next
The msm next tree is based on rc3, so let's just backmerge rc7 before pulling it in.
Signed-off-by: Dave Airlie <airlied@redhat.com>
TMP461 is almost identical to TMP451, which is already supported by the
lm90 driver. At the same time, unlike other sensors from the TMP401
compatible series, it only supports 8-bit temperature read operations,
and it supports negative temperatures when configured for its default
temperature range, and it supports a temperature offset register.
Supporting this chip in the tmp401 driver adds unnecessary complexity.
Remove its support from this driver and support the chip with the lm90
driver instead.
Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add PTP_CLK_MAGIC to the userspace-api/ioctl/ioctl-number.rst
documentation file.
Fixes: d94ba80ebbea ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20211024163831.10200-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add "arm,max-burst-size" optional property for TMC ETR.
If specified, this value indicates the maximum burst size
that can be initiated by TMC on the AXI bus.
Signed-off-by: Tanmay Jagdale <tanmay@marvell.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210901131049.1365367-2-tanmay@marvell.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
This change documents the device tree bindings for the Nuvoton
NCT7802Y driver.
Signed-off-by: Oskar Senft <osk@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211020164213.174597-1-osk@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Detailed description for this pull request:
1. Add support for TUSB320L and update tusb320 extcon driver
- The existing extcon-usbc-tusb320 driver is updated
for supporting the mode setting and reset operation.
Also, this driver supports the simliar TUSB320L device
at the same extcon-usbc-tusb320 extcon provider driver.
2. Use p-unit semaphone lock for register access for extcon-axp288
driver
3. Update the minor clean-up for extcon-max3355 and extcon-usb-gpio
driver.
-----BEGIN PGP SIGNATURE-----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=qEVD
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon next for v5.16
Detailed description for this pull request:
1. Add support for TUSB320L and update tusb320 extcon driver
- The existing extcon-usbc-tusb320 driver is updated
for supporting the mode setting and reset operation.
Also, this driver supports the simliar TUSB320L device
at the same extcon-usbc-tusb320 extcon provider driver.
2. Use p-unit semaphone lock for register access for extcon-axp288
driver
3. Update the minor clean-up for extcon-max3355 and extcon-usb-gpio
driver.
* tag 'extcon-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon:
dt-bindings: extcon: usbc-tusb320: Add TUSB320L compatible string
extcon: usbc-tusb320: Add support for TUSB320L
extcon: usbc-tusb320: Add support for mode setting and reset
extcon: extcon-axp288: Use P-Unit semaphore lock for register accesses
extcon: max3355: Drop unused include
extcon: usb-gpio: Use the right includes
Document the FAN_FS_ERROR event for user administrators and user space
developers.
Link: https://lore.kernel.org/r/20211025192746.66445-32-krisman@collabora.com
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jan Kara <jack@suse.cz>
Fixes the schema check warning "audio-controller@32000: 'AVDD-supply'
do not match any of the regexes: 'pinctrl-[0-9]+'"
Fixes: 5c36abcd2621 ("ASoC: meson: add t9015 internal codec binding documentation")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20211026182754.900688-1-alexander.stein@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Player LEDs are commonly found on game controllers from Nintendo and Sony
to indicate a player ID across a number of LEDs. For example, "Player 2"
might be indicated as "-x--" on a device with 4 LEDs where "x" means on.
This patch introduces LED_FUNCTION_PLAYER1-5 defines to properly indicate
player LEDs from the kernel. Until now there was no good standard, which
resulted in inconsistent behavior across xpad, hid-sony, hid-wiimote and
other drivers. Moving forward new drivers should use LED_FUNCTION_PLAYERx.
Note: management of Player IDs is left to user space, though a kernel
driver may pick a default value.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a typo (are -> as) in the introduction paragraph of
Documentation/block/queue-sysfs.rst.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20211027022223.183838-6-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the file Documentation/block/queue-sysfs.rst to add a description
of a device queue sysfs entries related to independent access ranges
(e.g. concurrent positioning ranges for multi-actuator hard-disks).
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20211027022223.183838-5-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This rewrites the ux500/u8500 clock bindings in YAML schema and extends them
with the PRCC reset controller.
The bindings are a bit idiomatic but it just reflects their age, the ux500
platform was used as guinea pig for early device tree conversion of platforms
in 2015. The new subnode for the reset controller follows the pattern of the
old bindings and adds a node with reset-cells for this.
Cc: devicetree@vger.kernel.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210921184803.1757916-1-linus.walleij@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Histogram expressions now support division, and multiplication in
addition to the already supported subtraction and addition operators.
Numeric constants can also be used in a hist trigger expressions
or assigned to a variable and used by refernce in an expression.
Link: https://lkml.kernel.org/r/20211025200852.3002369-9-kaleshsingh@google.com
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This property is used to describe the total number of pins on this
particular pinctrl hardware block.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211026175815.52703-4-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO/pinctrl hardware can act as an interrupt-controller, so add
the #interrupt-cells property to the binding.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211026175815.52703-3-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added two options into "mode=" mount option to make it possible for
developers to simulate filesystem fragmentation/after-GC situation
itself. The developers use these modes to understand filesystem
fragmentation/after-GC condition well, and eventually get some
insights to handle them better.
"fragment:segment": f2fs allocates a new segment in ramdom position.
With this, we can simulate the after-GC condition.
"fragment:block" : We can scatter block allocation with
"max_fragment_chunk" and "max_fragment_hole" sysfs
nodes. f2fs will allocate 1..<max_fragment_chunk>
blocks in a chunk and make a hole in the length of
1..<max_fragment_hole> by turns in a newly allocated
free segment. Plus, this mode implicitly enables
"fragment:segment" option for more randomness.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The RPM and RPMh sleep stats are introduced on a number of platforms, to
aid the enablement of entering low power mode.
The MSM8916 support receives some polishing touches, followed by
introduction of the necessary pieces to use the DeviceTree on 32-bit
variants of the MSM8916 platform, in particular to boot the secondary
CPUs. Based on this support for the Samsung Galaxy S4 Mini Value Edition
is introduced.
The Asus Zenfone 2 Laser gained touchscreen, sensors and sdcard support.
MSM8996 got support for the its crypto hardware and the Xiaomi Mi 5
gained a description of its LCD panel.
The Trogdor device on SC7180 gained support for a second source eDP
brigde, while SC7280 gains PCIe support and the newly introduced
Herobrine device.
Both MSM8916 and SDM845 has their standalong SMEM node dropped, in favour
of the newly introduced support for specifying the compatible directly
on the reserved-memory node.
The SM7225 platform is introduced, as a derrivative of SM6350, initial
support for the PM6350 PMIC and based on this the Fairphone 4 is
introduced.
The RB3 and RB5 devices gains msm-id and board-id, to allow the two DTBs
to be baked into a single boot.img that can be booted on both devices.
As the GDSC driver has been extended to properly describe the
relationship between MMCX and MDSS_GDSC, the now deprecated mmcx
regulator is removed from SM8250.
SM8350 gained CPU topology, idle-states and fastrpc support. FastRPC was
also added for SM8150 and the SA8155p ADP got a couple of remoteprocs
enabled.
Additionally a number of DT validation issues was corrected across the
various platforms and devices.
-----BEGIN PGP SIGNATURE-----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=fQI7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=OHZ9
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DTS additional patches for v5.16
The RPM and RPMh sleep stats are introduced on a number of platforms, to
aid the enablement of entering low power mode.
The MSM8916 support receives some polishing touches, followed by
introduction of the necessary pieces to use the DeviceTree on 32-bit
variants of the MSM8916 platform, in particular to boot the secondary
CPUs. Based on this support for the Samsung Galaxy S4 Mini Value Edition
is introduced.
The Asus Zenfone 2 Laser gained touchscreen, sensors and sdcard support.
MSM8996 got support for the its crypto hardware and the Xiaomi Mi 5
gained a description of its LCD panel.
The Trogdor device on SC7180 gained support for a second source eDP
brigde, while SC7280 gains PCIe support and the newly introduced
Herobrine device.
Both MSM8916 and SDM845 has their standalong SMEM node dropped, in favour
of the newly introduced support for specifying the compatible directly
on the reserved-memory node.
The SM7225 platform is introduced, as a derrivative of SM6350, initial
support for the PM6350 PMIC and based on this the Fairphone 4 is
introduced.
The RB3 and RB5 devices gains msm-id and board-id, to allow the two DTBs
to be baked into a single boot.img that can be booted on both devices.
As the GDSC driver has been extended to properly describe the
relationship between MMCX and MDSS_GDSC, the now deprecated mmcx
regulator is removed from SM8250.
SM8350 gained CPU topology, idle-states and fastrpc support. FastRPC was
also added for SM8150 and the SA8155p ADP got a couple of remoteprocs
enabled.
Additionally a number of DT validation issues was corrected across the
various platforms and devices.
* tag 'qcom-arm64-for-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (77 commits)
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
arm64: dts: qcom: sdm845: Fix Qualcomm crypto engine bus clock
arm64: dts: qcom: msm8996: Add device tree entries to support crypto engine
arm64: dts: qcom: msm8996: move clock-frequency from PN547 NFC to I2C bus
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: sdm630: Add disabled Venus support
arm64: dts: qcom: pm660l: Remove board-specific WLED configuration
arm64: dts: qcom: Move WLED num-strings from pmi8994 to sony-xperia-tone
arm64: dts: qcom: pmi8994: Remove hardcoded linear WLED enabled-strings
arm64: dts: qcom: pmi8994: Fix "eternal"->"external" typo in WLED node
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch add a description and example of disable_wdt_extrst
element for watchdog on MTK Socs
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210914123454.32603-2-Fengquan.Chen@mediatek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
