IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is part of the future enablement of X550 SFP+ support. This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways. If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs. The occurs regardless of
whether the VF count was later modified through sysfs. If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe. If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.
>From the comment, commit da36b64736cf ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.
This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device. Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: Tal Abudi <talabudi@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use kzalloc rather than kcalloc(1..
The semantic patch that makes this change is as follows:
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS could be leveraged by taking account L4 src/dst ports
as ingredients, thus ingress skb Rx hash type should honor
such the real configuration.
Signed-off-by: Fan Du <fan.du@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for another 10baseT X550 device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices. This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for receiving interrupts from a external copper
PHY for the X550 part. This includes enabling, detection as well as
re-enablement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases. This patch pulls the text from the
same location. I noticed this as I am about to add another case.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This new method will control the PHY power state. You pass in the
state you wish to change to (ether on or off). For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom. This patch enables
these devices this support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values. These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because error codes are negative, it only makes sense to
consistently use signed types when handling them. Also remove
some explicit comparisons with 0 on these variables.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a898720 ("net: create generic bridge ops")
Fixes: 815cccbf10b2 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the new netdev op to allow user to enable/disable the ability
of a specific VF to query its RSS Indirection Table and an RSS Hash Key.
This patch limits the new feature support to 82599 and x540 devices only.
Support for other devices will be added later.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added get_rxfh_indir_size, get_rxfh_key_size and get_rxfh ethtool_ops
callbacks implementations.
This enables the ethtool's "-x" and "--show-rxfh[-indir]" options.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a preparation for enablement of ethtool RSS indirection
table and hash key querying. We don't want to read registers every time
the RSS info is queried. Therefore we will store its current content in the
arrays in the adapter struct and will read it from there (instead of from
registers) when requested.
Will change the code that writes the indirection table and hash key into
the HW registers to take its content from these arrays. This will also
simplify the indirection table updating ethtool callback implementation
in the future.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver hasn't used call_rcu to free the rings for some time now.
Since that is the case the call to rcu_barrier can be dropped since calls
to kfree_rcu don't require it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the HW_VLAN_CTAG_FILTER bit is not falsely
advertised as being a feature that can be toggled on ixgbe parts. The
driver was setting the bit in features and letting it be inherited by
hw_features, however the driver was actually ignoring the value of the bit
and just assuming it was always set. As a result VLAN filtering was always
enabled which is a requirement for SR-IOV, VMDq, DCB, FCoE, and possibly
other features within the adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will enable X550 Source Address Prunning for VEPA
bridge mode. This requires that we also have replication enabled
as well, while in this mode.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch gathers together all the logic needed to configure bridge
modes. Currently that it is rather simple but this is really laying
the ground work for future X550 feature enhancement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some dead code from the cleanup path for ixgbe.
Setting and clearing the flag doesn't do anything since all we are
doing is setting the flag, scheduling NAPI, clearing the flag and
then letting netpoll do the polling cleanup. As such it doesn't
make much sense to have it there.
This patch also removes one minor white-space error.
CC: <kernel-team@fb.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the X550 mac type we have to do additional steps around
enabling/disabling Rx. This patch will add a layer of indirection
around these support functions to enable this.
CC: <kernel-team@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.
Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
