IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ath10k_pci_diag_write_mem may allocate big size of the dma memory
based on the parameter nbytes. Take firmware diag download as
example, the biggest size is about 500K. In some systems, the
allocation is likely to fail because it can't acquire such a large
contiguous dma memory.
The fix is to allocate a small size dma memory. In the loop,
driver copies the data to the allocated dma memory and writes to
the destination until all the data is written.
Tested with QCA6174 PCI with
firmware-6.bin_WLAN.RM.4.4.1-00119-QCARMSWP-1, this also affects
QCA9377 PCI.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chomium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add dev_type parameter to struct ath10k_bus_params.
The dev type specifies if the device is a high latency device (usb and
sdio) or low latency device (pci, ahb and snoc)
The setup of high latency chips is sometimes different than
for chips using low latency interfaces.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This struct is used as argument to ath10k_core_register in order to
make it easier to add more bus parameters in the future.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To download firmware via diag interface, driver needs to write the target
memory space below 1M. It means the bit20 should be zero for the converted
address if the target memory space is below 1M. Otherwise, bit20 is one if
the target address is larger or equal to 1M space.
As downloading firmware via diag interface is only required for qca6174
and qca9377, a new specific function is introduced to convert the target
address to ce address: ath10k_pci_qca6174_targ_cpu_to_ce_addri().
This function supports to convert any target address to ce address.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delay 1ms is too long for both diag read and write operations.
This is observed when writing a big memory buffer to target or
reading a big memory buffer from target. Take writing/reading
512k bytes as example, the delay itself is 256ms as the maximum
length of every write/read is 2k size.
Reduce the delay to 50us for read and write operations.
Take the ath10k_pci_targ_cpu_to_ce_addr() out of loop and put it
in the beginning of the loop for ath10k_pci_diag_read_mem().
The ath10k_pci_targ_cpu_to_ce_addr() is to convert the address
from target cpu's perspective to CE's perspective, so it makes
no sense to convert a CE's perspective address again in the loop.
It's a wrong implementation but happens to work.
If the target address is below 1M space, then the convert in the loop
from the second time becomes wrong because the previously converted address
is larger than 1M. The counterpart ath10k_pci_diag_write_mem() has the
correct implementation.
With this change, ath10k_pci_diage_read_mem() works correctly no matter
the target address is below 1M or above 1M.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 target uses separate htc service for pktlog.
Add pktlog service request and support for pktlog
rx path handling.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Existing copy engine interrupt enable logic assumes that last
CE is using polling mode and due to this interrupt for last copy engine
are always disabled. WCN3990 uses last CE for pktlog and
interrupt remains disabled with existing logic.
To mitigate this issue, introduce CE_ATTR_POLL flag and control
the interrupt based on the flag which can be set in ce_attr.
Testing:
Tested on WCN3990 and QCA6174 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush
Steps:
In a certain condition, during wifi down below scenario might occur.
ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change type of hif sg tx paddr to dma_addr_t for
supporting target having addressing mode greater than
32 bit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preparation for a new QCA9377 firmware release. The new firmware release
requires more IRAM banks, hence update that on ath10k.
The IRAM banks promotion won't break any backwards compatibility, as those IRAM
banks were not getting used in previous firmware releases.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add memory dump to the firmware crash data file which is provided to user space
via devcoredump interface. This makes it easier for firmware engineers to debug
firmware crashes.
Due to increased memory consumption the memory dump is disabled by default. To
enable it make sure that bit 3 is set in coredump_mask module parameter:
modprobe ath10k_core coredump_mask=0xffffffff
When RAMDUMP is enabled a buffer for the dump is allocated with vmalloc during
device probe. The actual memory layout is different in hardware versions and
the layouts are defined in coredump.c. The memory is split to regions and, to
get even finegrained control of what to copy, the region can split to smaller
sections as not all registers are readable (which could cause the whole system
to stall).
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: refactoring and cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation to add RAM dump support. No functional changes, only moving code
and renaming function names.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 CE descriptor uses 64bit address for
src/dst ring buffer. It has extended field for toeplitz
hash result, which is being used for HW assisted
hash results.
To accommodate WCN3990 descriptor, define new CE
descriptor for extended addressing mode and related
methods to handle the descriptor data.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE send and receive API's are using u32 ring address, which
truncates the address for target with 64bit addressing range.
Use dma_addr_t for ce buffers to support target with extended
addressing range.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Build errors have been reported with CONFIG_PM=n:
drivers/net/wireless/ath/ath10k/pci.c:3416:8: error: implicit
declaration of function 'ath10k_pci_suspend'
[-Werror=implicit-function-declaration]
drivers/net/wireless/ath/ath10k/pci.c:3428:8: error: implicit
declaration of function 'ath10k_pci_resume'
[-Werror=implicit-function-declaration]
These are caused by the combination of the following two commits:
6af1de2e4ec4 ("ath10k: mark PM functions as __maybe_unused")
96378bd2c6cd ("ath10k: fix core PCI suspend when WoWLAN is supported but
disabled")
Both build fine on their own.
But now that ath10k_pci_pm_{suspend,resume}() is compiled
unconditionally, we should also compile ath10k_pci_{suspend,resume}()
unconditionally.
And drop the #ifdef around ath10k_pci_hif_{suspend,resume}() too; they
are trivial (empty), so we're not saving much space by compiling them
out. And the alternatives would be to sprinkle more __maybe_unused, or
spread the #ifdef's further.
Build tested with the following combinations:
CONFIG_PM=y && CONFIG_PM_SLEEP=y
CONFIG_PM=y && CONFIG_PM_SLEEP=n
CONFIG_PM=n
Fixes: 96378bd2c6cd ("ath10k: fix core PCI suspend when WoWLAN is supported but disabled")
Fixes: 096ad2a15fd8 ("Merge branch 'ath-next'")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.15. Major changes:
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
there it's supported (QCA99x0 and QCA4019)
For devices where the FW supports WoWLAN but user-space has not
configured it, we don't do any PCI-specific suspend/resume operations,
because mac80211 doesn't call drv_suspend() when !wowlan. This has
particularly bad effects for some platforms, because we don't stop the
power-save timer, and if this timer goes off after the PCI controller
has suspended the link, Bad Things will happen.
Commit 32faa3f0ee50 ("ath10k: add the PCI PM core suspend/resume ops")
got some of this right, in that it understood there was a problem on
non-WoWLAN firmware. But it forgot the $subject case.
Fix this by moving all the PCI driver suspend/resume logic exclusively
into the driver PM hooks. This shouldn't affect WoWLAN support much
(this just gets executed later on).
I would just as well kill the entirety of ath10k_hif_suspend(), as it's
not even implemented on the USB or SDIO drivers. I expect that we don't
need the callback, except to return "supported" (i.e., 0) or "not
supported" (i.e., -EOPNOTSUPP).
Fixes: 32faa3f0ee50 ("ath10k: add the PCI PM core suspend/resume ops")
Fixes: 77258d409ce4 ("ath10k: enable pci soc powersaving")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When CONFIG_PM_SLEEP is disabled, we get a compile-time
warning:
drivers/net/wireless/ath/ath10k/pci.c:3417:12: error: 'ath10k_pci_pm_resume' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/pci.c:3401:12: error: 'ath10k_pci_pm_suspend' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_suspend(struct device *dev)
Rather than fixing the #ifdef, this just marks both functions
as __maybe_unused, which is a more robust way to do this.
Fixes: 32faa3f0ee50 ("ath10k: add the PCI PM core suspend/resume ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The actual PCI suspend/resume in ath10k has been handled in wow.c,
but in the case of the device doesn't support remote wakeup,
the .hif_suspend() and .hif_resume() will never be handled.
ath10k_wow_op_suspend()
{
if (WARN_ON(!test_bit(ATH10K_FW_FEATURE_WOWLAN_SUPPORT,
ar->running_fw->fw_file.fw_features))) {
ret = 1;
goto exit;
}
....
ret = ath10k_hif_suspend(ar);
}
So register the PCI PM core to support the suspend/resume if the device
doesn't support remote wakeup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove bus specific dependencies from CE layer
to have common CE layer across multiple targets.
This is required for adding support for WCN3990
chipset support as WCN3990 chipset uses SNOC
bus interface with Copy Engine endpoint.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following spelling mistakes in messages:
syncronise -> synchronize
unusally -> unusually
addrress -> address
inverval -> interval
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lets one have a clue that maybe timeouts are happening
when we just aren't waiting long enough.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For QCA6174 hw3.0, since WLAN.RM.4.4-00022-QCARMSWPZ-2, it starts to
support the board ID information from otp, with some devices released on
the market that didn't calibrated with OTP, will have 0 for board ID
information, which cause the backward compatibility issue and was fixed
in commit 'd2e202c06ca4 ("ath10k: ignore configuring the incorrect board_id")'
So bump the fw api version to differentiate the latest firmware support.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check on ret for an error is redundant because it is already been
checked for non-zero earlier on and ret is never non-zero at this point.
Fix this by removing the redundant check and error message.
Detected by CoverityScan, CID#1357170 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes the below crash when ath10k probe firmware fails, NAPI polling tries
to access a rx ring resource which was never allocated. An easy way to
reproduce this is easy to remove all the firmware files, load ath10k modules
and ath10k will crash when calling 'rmmod ath10k_pci'. The fix is to call
napi_enable() from ath10k_pci_hif_start() so that it matches with
napi_disable() being called from ath10k_pci_hif_stop().
Big thanks to Mohammed Shafi Shajakhan who debugged this and provided first
version of the fix. In this patch I just fix the actual problem in pci.c
instead of having a workaround in core.c.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
__ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
Call Trace:
[<ffffffffa113ec62>] ath10k_htt_rx_msdu_buff_replenish+0x42/0x90
[ath10k_core]
[<ffffffffa113f393>] ath10k_htt_txrx_compl_task+0x433/0x17d0
[ath10k_core]
[<ffffffff8114406d>] ? __wake_up_common+0x4d/0x80
[<ffffffff811349ec>] ? cpu_load_update+0xdc/0x150
[<ffffffffa119301d>] ? ath10k_pci_read32+0xd/0x10 [ath10k_pci]
[<ffffffffa1195b17>] ath10k_pci_napi_poll+0x47/0x110 [ath10k_pci]
[<ffffffff817863af>] net_rx_action+0x20f/0x370
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 3c97f5de1f28 ("ath10k: implement NAPI support")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYkafBAAoJEG4XJFUm622b0EAH/3mFY0WDfdR/Ych29HX1M/Ao
Bd5gQfKzHS8ANR56qqmxEbpLdBnBa8iNC0IS4RFsWVv6qMoEEOHDLeY5W9XsomWK
i45fQN2XIdjBUOyDXUjsyz006cMe79VzRvFf9gfSekP8i8BCWQzyYC8VKt/F+6Sh
yo9yA4Yv3zA3mA3yRKtxSjLm/6xUXCFVNshKGT0rXc/oEfIN6OnIC1k0p0xw2hhl
GyLN6PSGOqcJc91+IoGOg4TaHzPdWJcWatuxGdQn8gKSDg0+gXaNh9Gtf4H/ojqp
Fwt2Ckk5mgJYk/2TAuFRpRXNMTJznUhp4Tjp2AE7EVM0f5JujUbQuPblOVfLIYk=
=vKKN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CORE_CTRL_ADDRESS is offset in register address space, it does not
make sense to OR it to derive the final address. It looks like its
a typo, so fix it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
use dma_zalloc_coherent() instead of dma_alloc_coherent and memset().
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYalDTAAoJEG4XJFUm622ba2EH/ivoHG9CvmT6HgNw77odDr6b
Zc7plDi2dd9LIzp3rF/9j8Ietfzpu31Pp9Qz0o1Su/s8RJIlXKVF5UeG5IignnEG
02rv7Z+BGPW7SUNDb0cLa27PMYqUAh8vI39sxYSdQ9NQLIlpMLIxxx5iOZyAK5eV
HBRS0pVlSxbAntb1JgWiN/LjjXe/PdhX3CR/b9b468KAcWB6UWj9nXQxFmz7d3uM
dH3buDTgwaq7K24ZAFc1BsD7rgxprpauXxgIMWCKxRERf64WFfYkYdfdCER+PSPH
maV5Te1KzTJBrQHDOPs1ezVe8gDUhb5YE4BJY9SppZpOE1arucq2g3+3obQUeHE=
=DAVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b3389a ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trival fix to remove unused variable ar_pci in ath10k_pci_tx_pipe_cleanup
when building with W=1:
drivers/net/wireless/ath/ath10k/pci.c:1696:21: warning: variable
'ar_pci' set but not used [-Wunused-but-set-variable]
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
caldata is not being free'd on the error exit path, causing
a memory leak and data definitely should not be freed. Free
caldata instead of data.
Thanks to Kalle Valo for spotting that data should not be
free'd.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3c97f5de1f28 ("ath10k: implement NAPI support") conflicts with
ath-current. To avoid any merge problems merge ath-current to ath-next already now.
Conflicts:
drivers/net/wireless/ath/ath10k/htt_rx.c
