IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When immediate quiet bit is set in CSA, the entire channel is blocked
by the firmware. It is expected that all the MACs will evacuate the
channel and the phy will be eventually either moved or removed.
Currently, the phy context is just unreferenced and thus, the quiet
bit is kept set and it will be impossible to TX on this phy, if we
will need to reuse it in the future. This can be seen when doing a
channel switch with mode=1 (quiet) twice from channel X to Y and then
back to channel X.
Fix that, by moving the phy context to a default channel when not
referenced anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an AP which supports HT and a single HT
station is connected, we change the min_width from
NL80211_CHAN_WIDTH_20_NOHT to NL80211_CHAN_WIDTH_20. This
of course has no implication on the channel width but still
sends a command to the firmware.
Remember the last width that was sent and refrain from
sending unnecessary commands to the firmware.
Sending a PHY_CTXT_CMD to the firmware has a cost since it
recalculates the presence on the medium and because of that
it closes the transmit queues for a short while.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 CDB firmware, we cannot update phy context to a
different band - we must first remove it and add it
again. Support this flow for all a000 devices since
we may have various combinations that cause us to fail
regardless if CDB is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
