IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Modules: HDA Codec driver
The following patch adds a 'test' ALC260 model specification to the
patch_realtek.c driver if CONFIG_SND_DEBUG is set. This is similar to the
'test' ALC880 model in that it sets up mixer controls for almost everything
to make it easier for people to test their laptop/soundcard when working out
what pin widgets are connected to which real-world devices.
This patch assumes my previous patch (adding the second PCM to the ALC260)
has previously been applied since it uses infrastructure added by that
patch.
In developing this patch it was found that not all retasking pins accept all
the modes - in particular, some ignore the VREFxx variants. The pin mode
control has therefore been tweaked to prevent this becoming a problem in
mixer applications.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
The following patch changes the initverbs associated with the output sum
widgets 0x08, 0x09 and 0x0a used with the fujitsu model in patch_realtek.c.
It is against alsa 1.0.11rc3.
Currently these widgets have their output muted, but a close reading of the
datasheet suggests that they don't actually have an output mute. They have
an *input* mute for each of their two inputs and a single output gain. This
patch therefore activates the input mutes and zeros the output gain. It has
not yet been tested but the above interpretation of the ALC260 datasheet
seems correct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
The following patch against alsa 1.0.11rc3 creates a PCM device (pcm1c) for
the second ADC present on the ALC260 codec used by the hda driver. It also
defines a new mixer control allowing the mode of retasking pins to be set;
this means a user can (for example) designate the headphone jack to be a
second input. With this patch in place it is possible to do 4 channel
recording on laptops equipped with an ALC260 codec assuming both a stereo
line-in jack is provided in addition to a headphone jack.
Mixer controls are provided to allow the headphone jack to be switched as
an input. In addition, an (input only) mode control is configured for
the line-in jack to allow a bias voltage to be requested (VREF80 or VREF50)
so headsets based on condensor microphones have a chance of working.
This patch has been tested on a Fujitsu S7020 laptop and as such these
features are currently only configured for the 'fujitsu' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec
Added the support of static resolution table support for codecs
that the driver cannot probe the volume resolution properly.
The table pointer should be set in each codec patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
- added 0x107d:0x6606 to whitelist
- print also the pci device ID for developers when model is not known
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: ICE1712 driver
Change the value written to hardware configuration register of envy24 chip
in the case of Terratec DMX6fire to restrict the active ADCs & DACs to 6.
Also add the dxr_enable module option to eventually leave the old behaviour
when user requests.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: USB generic driver
Rename QUIRK_MIDI_MIDITECH to QUIRK_MIDI_CME because Miditech keyboards
are built by CME and use the same protocol, and don't force a Miditech
product name for the USB ID used by both Miditech and CME UF-x
keyboards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: PCM Midlevel,USB generic driver
Because snd_pcm_format_name() function is used only for informational
purposes, it is no longer exported from the PCM midlevel to reduce
space and dependency. usbaudio module shows only numeric value for format.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
Forth of 4 es18xx.c patches culminating in Zoom Video support.
This patch adds Zoom Video support for those chipsets that support it.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879. I could not test the Zoom Video function for an ES1878 or
ES1869.
Patches were created against the Sarge code and then edited to apply
correctly to the
ALSA cvs code. Lastly the patched ALSA cvs code was test for successful
compilation.
No additional testing was done on the ALSA cvs version.
One quirk (noted in my comments below) is that apparently the datasheet
is wrong
for one of the ES1879 Zoom Video 'enable' bits, because
1) if you set this bit it messes up PCM playback (speaker_test play a
lower frequency)
2) even if you don't set this bit Zoom Video still works.
I added a control to toggle the bit on just in case there might be a
version of the
ES1879 that requires it, but I expect noone will need it.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
Third of 4 es18xx.c patches culminating in Zoom Video support.
This patch changes the Hardware Volume support to reflect the fact that
not all of the
supported chipsets have seperate registers dedicated to the Hardware
Volume inputs. Although
all the chipsets can generate an HWV interrupt whenever a Hardware
Volume input is received
only those with seperate HWV registers can split the HWV registers from
the Master volume
registers.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
Second of 4 es18xx.c patches culminating in Zoom Video support.
This patch changes the 'record source' mux routines to reflect the fact
that not all of the
supported chipsets have 8 possible inputs. Some have 4 and some have 5.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES18xx driver
First of 4 es18xx.c patches culminating in Zoom Video support.
While adding support for Zoom Video to the es18xx driver I found some of
the mixer controls
were wrong. Since you guys went to the trouble of supplying the
datasheets for the supported
chipsets I did a review of all of them and tried to get es18xx.c to
accurately reflect the
proper mixer controls for each chipset. If the datasheets are wrong then
so are my patches.
This first patch moves some controls from the common-to-all-chipsets array
'snd_es18xx_base_controls' to a chipset-specific array and adds code to
manage that new array.
Also while testing on my ES1878 test machine I discovered it needed a
couple of udelays in
the identify function so those are in this patch as well.
Testing:
This work was initially done on the source from the Debian Sarge ALSA
package, then tested
on an ES1879 and an ES1878 machine. Patches were created against the
Sarge code and then edited
to apply correctly to the ALSA cvs code. Lastly the patched ALSA cvs
code was test for
successful compilation. No additional testing was done on the ALSA cvs
version.
Signed-off-by: Mark Salazar <markTheCoder@justmyself.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
Fix the driver codes to run on 64bit architectures.
The patch taken from ALSA BTS bug#1047.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA Core,PCM Midlevel,ALSA<-OSS emulation,USB generic driver
1) The verbose procfs code for the PCM midlevel and usb audio
can be removed now (more patches will follow).
CONFIG_SND_VERBOSE_PROCFS
2) The PCM OSS plugin system can be also compiled optionaly.
CONFIG_SND_PCM_OSS_PLUGINS
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).
We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Documentation,HDA Intel driver
Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
Fix the detection of tertriary codec on SIS7012, including clean-ups
of relevant codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Move the common packet size calculation code from
prepare_startup_playback_urb() and prepare_playback_urb() to a new
function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
This is my naive attempt at adding ALSA device support. The attached
patch provides support for the EDIROL UM-3ex. This is a 3-port USB midi
interface with a built-in USB hub and the ability to chain 2 other
UM-3x's in a master-slave configuration. I only have one, so I do not
know how this works in practice.
Though this is a 3-port device, I had to throw in that 4th 'Control' interface
to the definition in order to make the 3rd port work. If I set in/out_cables
to 0x000b, a 3rd interface appears on the driver, but it does nothing.
Changing it to 0x000f allows the 3rd interface to work, but of course
interface 4 does not work because it does not exist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_device_free() for an opl3-oss instance which should have been
released.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed on 2.6.16-rc4 that my MPU-401 wasn't functional, due to a simple
copy & paste error in sound/isa/cs423x/cs4236.c.
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm getting oopses with snd-usb-audio in 32-bit compat environments:
control_compat.c:get_ctl_type() doesn't initialize 'info', so
'itemlist[uinfo->value.enumerated.item]' in
usbmixer.c:mixer_ctl_selector_info() might access random memory (The 'if
((int)uinfo->value.enumerated.item >= cval->max)' doesn't fix all problems
because of the unsigned -> signed conversion.)
Signed-off-by: Juergen Kreileder <jk@blackdown.de>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerMac sound drivers used to rely on a "bug" of the i2c-keywest
driver that implemented I2C_SMBUS_BLOCK_DATA incorrectly, that is it did
what I2C_SMBUS_I2C_BLOCK_DATA should have done. The new i2c-powermac
driver that replaces keywest has this bug fixed, thus the sound drivers
must be fixed too.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
AACI reports TX FIFO full after the first write to it if the AC97 is not
enabled. This patch enables the AC97 probing before the check for the TX
FIFO size. The patch also adds a warning if the TX FIFO size is not
multiple of 16.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modules: HDA Codec driver
This little patch add the model for the motherboard K8N51 from Gigabyte
to the known models of ALC boards.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
* Fix init sequence so manually retaskable jacks don't get added to
the line_out list.
* Update intel mobo config defaults to specify surround outputs
as line outs rather than speakers.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: OPL3SA2 driver,GUS Classic driver
dma2 is a global array. sprintf below suggests there was a typo.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Fix max_channels computation for STAC92xx codecs in the case only
HP pin without line-out pins is detected in the default pin config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This adds support for Agere's variant of Si3054/5 based HDA modem.
Signed-off-by: Sasha Khapyorsky <sashak@alsa-project.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: CS4236+ driver
PnP ids for Netfinity 3000 builtin soundcard.
This one works for me.
This patch was submitted through kernel Bugzilla #4214.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
au_readl() does needed byteswapping, etc.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modules: PPC PMAC driver
In 2.6.16-rc1 there is a small typo introduced by the
'Remove device_node addrs/n_addr' changes
which prevents my Powerbook G4 sound from working:
Advanced Linux Sound Architecture Driver Version 1.0.11rc2
(Wed Jan 04 08:57:20 2006 UTC).
snd: can't request rsrc 0 (Sound Control: 0x80000000:80004fff)
ALSA device list:
No soundcards found.
The patch below fixes it. Of course, the patch fixing the i2c issues
('i2c_smbus_write_i2c_block_data' patch) needs to be applied to in
order for the sound to completly work.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Digigram PCXHR driver
sound/pci/pcxhr/pcxhr.c: In function 'pcxhr_update_r_buffer':
sound/pci/pcxhr/pcxhr.c:460: warning: unsigned int format, different type arg (arg 7)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: RME9652 driver
sound/pci/rme9652/hdspm.c: In function 'snd_hdspm_preallocate_memory':
sound/pci/rme9652/hdspm.c:3327: warning: int format, different type arg (arg 4)
sound/pci/rme9652/hdspm.c:3331: warning: int format, different type arg (arg 4)
sound/pci/rme9652/hdspm.c: In function 'snd_hdspm_create':
sound/pci/rme9652/hdspm.c:3513: warning: int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
This patch adds a quirk entry for the Dell Optiplex GX270, on which
the volume is set by the headphone control, not the master control.
Signed-off-by: Chris Ball <cjb@mrao.cam.ac.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALI5451 driver
This patch uses #defines for the Vendor ID and Device ID and uses the
new PCI_DEVICE macro.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Trident driver
Some pcnet32 hardware erroneously has the Vendor ID for Trident. The
pcnet32 driver looks for the PCI ethernet class before grabbing the
hardware, but the current trident driver does not check against the
PCI audio class. This allows the trident driver to claim the pcnet32
hardware. This patch prevents that.
Per Jiri Slaby's request, I changed the trident driver to use
PCI_DEVICE macro and PCI ID #defines.
This patch is untested on Trident 4DWAVE_DX hardware, but has been
tested on pcnet32 hardware.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
On the Audigy 2 ZS, disable all sample rate that are not a multiple of
48 kHz because the others work only with the digital output which is
not yet supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: YMFPCI driver
Set the (read only) sample rate field in the IEC958 mixer controls to
48 kHz (instead of 44.1 kHz) because that is the rate actually
supported by the hardware.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Some widespread USB interface chips with adaptive iso endpoints hang
after receiving a series of empty packets when they expect data (ALSA
bug#1585). To avoid this, we have to send packets containing silence
(zero samples) instead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: AC97 Codec
Added a blacklist to suppress to create jack sense controls.
These controls must be always off on some devices (e.g. Thinkpad).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Intel driver
This patch adds the Intel ICH8 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
The patch siply adds the PCI IDs of AVerMedia Studio No. 103, 203,
and possibly even other versions with the same PCI IDs to the snd-bt87x
driver and sets its default sampling rate to 48 kHz.
Signed-off-by: Martin Drab <drab@kepler.fjfi.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
in recent -mm kernels additional quirks for ac97 hardware in HP laptops
have been added. However, now the list in intel8x0.c contains a duplicate,
since the HP nx6110 and nc6120 have identical subdevice ids.
This was introduced in -mm1 by the following patch:
add-new-quirk-for-devices-with-mute-leds-and-separate-headphone-volume.patch
Since the HP nx6110 and nc6120 are almost identical, both entries
should really be combined, as in the following patch. I have checked
that AC97_TUNE_HP_MUTE_LED is the right thing to do.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some pcnet32 hardware erroneously has the Vendor ID for Trident. The
pcnet32 driver looks for the PCI ethernet class before grabbing the
hardware, but the current trident driver does not check against the PCI
audio class. This allows the trident driver to claim the pcnet32 hardware.
This patch prevents that.
This revised version of the OSS Trident patch includes PCI_DEVICE Macro
usage.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Muli Ben-Yehuda <mulix@mulix.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sound/oss/dmasound/dmasound_atari.c has static expand_bal
sound/oss/dmasound/dmasound_q40.c has static expand_bal
sound/oss/dmasound/dmasound_awacs.c has non-static expand_bal
sound/oss/dmasound/trans_16.c uses expand_bal from dmasound_awacs.c
all 4 include dmasound.h; extern for expand_bal used to be there,
which is a bloody bad idea, considering _atari and _q40. Moved the
extern to trans_16.c.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cast is not an lvalue
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid warnings about use of cast expressions as lvalues
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move capable() from sched.h to capability.h;
- Use <linux/capability.h> where capable() is used
(in include/, block/, ipc/, kernel/, a few drivers/,
mm/, security/, & sound/;
many more drivers/ to go)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sound/oss/i810_audio.c:3431: warning: label `out_pio' defined but not used
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
OSS Harmony got missed on the conversion of parisc_device.hpa to a
struct resource... fix its build.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
A simple driver for the CS5535 and CS5536 that allows a user-space program
to manipulate GPIO pins. The CS5535/CS5536 chips are Geode processor
companion devices.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Request the IRQ after having set everything up. Otherwise a shared interrupt
at the right time can kill the machine.
Found this with David Woodhouse <dwmw2@infradead.org>'s
debug-shared-irqs.patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove various things which were checking for gcc-1.x and gcc-2.x compilers.
From: Adrian Bunk <bunk@stusta.de>
Some documentation updates and removes some code paths for gcc < 3.2.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change removes the old, deprecated interface from the opl3sa2 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files. This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes the old, deprecated interface from the nm256 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files. This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Note that this driver has been obsoleted by an ALSA equivalent.
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes the old, deprecated interface from the maestro driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files. This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
The check_suspend() function and associated logic was not removed, even though
it is now unnecessary.
Note that this driver has been obsoleted by an ALSA equivalent.
Acked-by: Zach Brown <zab@zabbo.net>
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes the old, deprecated interface from the cs46xx driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files. This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Note this driver has PCI PM hooks which are set properly. It also has the
ability to trigger suspend/resume from an ioctl. This functionality was not
touched, though it could use a serious review if this driver continues to
persist in the mainline tree..
Note that this driver has been obsoleted by an ALSA equivalent.
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes the old, deprecated interface from the cs4281 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files. This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Note that this driver has been obsoleted by an ALSA equivalent.
Note that this driver has hooks for PCI power management, but does not
implement the ->suspend()/->resume() methods.
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes the old, deprecated interface from the ad1848 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files. This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for ppc arch.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the OSS drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the PCMCIA sound drivers to handle the recent changes to the PCMCIA
core. A part of this merge was done by Takashi Iwai <tiwai@suse.de>.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Modules: ALSA Core
Revert the nested-device patch to keep the compatibility with the
current HAL configuration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
Description:
Part way to fix ALSA bug#927
Add support for the SPI interface on the CA0108 chip.
This is used to control the registers on the DAC.
Headphone output tested.
Other outputs and Capture not tested yet.
Note: The red LED does not come on, but sound is still OK.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
Modules: ES1968 driver
Fix disablement of TDMA and legacy support to prevent confliction of
resources with ISA boards. Confirmed with Terratec DMX and CS4236.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ARM PXA2XX driver
The SDONE and CDONE interrupt on the PXA27x might become unusable in
some conditions. Let's use an hybrid approach (interrupt with timeout)
to have the best possible behavior in all conditions.
Also let's not care about CAR_CAIP anymore. This is useless.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA sequencer
Reduce the maximum possible number of global clients to 16 to make
more numbers available for card clients, and allow dynamically allocated
card client numbers to share the same range as application client
numbers to make sure that all 32 cards can be used at the same time.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
All users of snd_seq_create_kernel_client() have to set the client name
anyway, so we can just pass the name as parameter. This relieves us
from having to muck around with a struct snd_seq_client_info in these
cases.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The fields of struct snd_seq_client_callback either aren't used or are
always set to the same value, so we can get rid of it altogether.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer
None of the fields of struct snd_seq_kernel_client was actually used, so
remove them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: YMFPCI driver
Instead of 'DS-XG', show the correct chip model (DS-1/1L/1S/1E) where possible.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: HDA Codec driver,HDA generic driver
- Common labels for input pins
- Fix and clean up of Realtek codec parsers
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ENS1370/1+ driver
Move the spdif and lineio parameters around so that they are compiled
even when SUPPORT_JOYSTICK isn't set.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: EMU10K1/EMU10K2 driver
Added the chip-detail entry for SB Live 5.1 Digital OEM [SB0220, (c) 2003].
Signed-off-by: Gergely Tamas <dice@mfa.kfki.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec,ATIIXP driver,Intel8x0 driver
This patch adds a new quirk for ac97 hardware that combines the existing
AC97_TUNE_MUTE_LED and AC97_TUNE_HP_ONLY quirks. This is needed for several
current HP laptops. Additionally, it adds the HP nx6125 to the
AC97_TUNE_MUTE_LED list.
Fixed for the latest version of ALSA by Takashi Iwai <tiwai@suse.de>.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec
Small fix for ALC65x codec, sync with Realtek's driver codes:
- Rename 'IEC958 Playback Route' to 'IEC958 Playback Source' so that
mixer can handle it properly
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA generic driver
This patch adds the support of ALC262,ALC883,ALC885,ALC861 to driver
More models and improvements for ALC880, ALC260 and ALC882 codecs, too.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
sound/pci/emu10k1/emufx.c: In function 'snd_emu10k1_efx_alloc_pm_buffer':
sound/pci/emu10k1/emufx.c:2402: error: implicit declaration of function 'vmalloc'
sound/pci/emu10k1/emufx.c:2402: warning: assignment makes pointer from integer without a cast
sound/pci/emu10k1/emufx.c: In function 'snd_emu10k1_efx_free_pm_buffer':
sound/pci/emu10k1/emufx.c:2413: error: implicit declaration of function 'vfree'
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
Distorted sound now comes from the Audio Out socket. Still more work to do.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
Modules: PPC PMAC driver
The last addition of 17' powerbook support seems buggy
(it's not Toonie indeed). Removed again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
pci_dma_supported() is called right before pci_set_dma_mask() which already
calls pci_dma_supported(). The attached patch removes the unneeded call to
pci_dma_supported()
Additionally the custom VORTEX_DMA_MASK macro is replaced by DMA_32BIT_MASK
from linux/dma-mapping.h
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: SPARC DBRI driver
Don't return errors if the proc file can't be created (for the case
without CONFIG_PROC_FS).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA<-OSS emulation,ALSA sequencer,ALSA<-OSS sequencer
Optimize the code when compiled without CONFIG_PROC_FS (in seq and oss
emulation parts).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: PPC PMAC driver
The audio chip in my Spring 2005 17' PowerBook was incorrectly
recognized as an AWACS chip. This adds the chip ID to the
snd_powermac driver such that it is recognized as a Toonie (I don't
know if that's correct, but it's the only one that makes it work at
all). and sorts the ID lists numerically. NOTE: This chip is only
minimally supported at this point; it has system beep support and
very low volume speaker output, and that's about it.
Signed-off-by: Kyle Moffett <mrmacman_g4@mac.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
- Explictly set pin control as input for all input pins
- Fix bug in 922x mixer (no mute on adc0vol)
- Remove broken ch_mode control
- Add support for jack retasking mixer controls to use rear line and
mic as surround outputs
- Add board tables to support autodetect and pin config defaults for
systems with broken bioses
- Add support for several Intel mobos
- Add support for DFI mobo with reference boards attached
(gets rid of compile time switch to use reference boards)
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Sound Core,Generic drivers
AC97 Kconfig entries broke the ALSA device drivers menu, so move them to a
location where that won't happen, enabling all device sub-menus to be
presented together.
Fixed for the latest ALSA tree by Takashi Iwai <tiwai@suse.de>.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Intel driver
The probe_mask module parameter comment notes that the intended
default is -1. Fix it to be so, otherwise all codecs are skipped
and init fails.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ENS1370/1+ driver
- spdif module option: some hardware revisions are without spdif output
- lineio module option: force shared line in / rear out jack settings
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: AC97 Codec
The following patch adds some extra IDs for the list of hardware which
should have headphone line sense enabled by default.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Fix/enhance AD1988 support code.
- Fix for h/w bug of AD1988A rev 2
- The BIOS auto-configuration is added and used as fallback
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Intel driver
- Use the position buffer for obtaining the current DMA position
as default. This seems more stable than others.
- Add probe_mask module option (mainly for test boards with multiple
codecs).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch is to fix the problem of calculating the nid incorrectly
when auto-probe for ALC880. The problem to be fixed often behaves
with such words when using dmesg, 'num_steps = 0 for NID=0x8' when
auto-probe for ALC880.
The patch contains:
- alsa-kernel/pci/hda/patch_realtek.c: replace 'alc880_dac_to_idx'
with 'alc880_idx_to_dac' in function 'alc880_auto_fill_dac_nids()'
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: RawMidi Midlevel,HDA generic driver
This patch contains the following possible cleanups:
- pci/hda/hda_proc.c should #include 'hda_local.h' for including the
prototype of it's global function snd_hda_codec_proc_new()
- core/rawmidi.c: make the needlessly global and EXPORT_SYMBOL'ed
function snd_rawmidi_info() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Somebody at Edirol fucked up and released a new revision of the UA-20
without class-specific descriptors, so now we have to hard-code the
sample format.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: HDA Codec driver
Fix AD1988 support. As default, 6stack model is used.
Still no auto-BIOS setup is implemented.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA generic driver
- Fix connection list parsing (with ranged flag).
- Increase the max number of connections
- Introduce widget capabilities cache
- Power up/down widgets at init, suspend and resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: RawMidi Midlevel
When the output buffer size is changed, runtime->avail must be
adjusted to the new size; otherwise, draining of a bigger buffer would
appear to fail because avail does not reach buffer_size.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA Core,Memalloc module,ALSA sequencer
With dynamic minor numbers, we can increase the number of sound cards.
This requires that the sequencer client numbers of some kernel drivers
are allocated dynamically, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer,Generic drivers
To allow increasing the maximum number of sound cards, we have to limit
the number of sequencer clients per card because client numbers are
still allocated statically.
Reducing the number of clients to four limits the number of sequencer
MIDI ports to 1024 per card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA Core,ALSA Minor Numbers
Add an option to allocate device file minor numbers dynamically.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of storing the pointers to the device-specific structures in an
array, put them into the struct snd_minor, and look them up dynamically.
This makes the device type modules independent of the minor number
encoding.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA Core
Store the snd_minor structure pointers in one array instead of using a
separate list for each card. This simplifies the mapping from device
files to minor struct by removing the need to know about the encoding
of the card number in the minor number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of a comment string, store the device type in the snd_minor
structure. This makes snd_minor more flexible, and has the nice side
effect that we don't need anymore to create a separate snd_minor
template for registering a device but can pass the file_operations
directly to snd_register_device().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RawMidi Midlevel
In snd_rawmidi_info_select(), check that the device identified by the
passed device number actually exists.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: CS5535 driver
Move the #include of <sound/driver.h> to the top which is
required for compilation on earlier kernels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: PPC,PPC PMAC driver,PPC PowerMac driver
Rewrite the probe/remove with platform_device.
Move the PM support to platform_device's callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
