IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm-390: Let kernel exit SIE instruction on work
[S390] dasd: check sense type in device change handler
[S390] pfault: fix token handling
[S390] qdio: reset error states immediately
[S390] fix page table walk for changing page attributes
[S390] prng: prevent access beyond end of stack
[S390] dasd: fix race between open and offline
F15h CPUs may report a non-DRAM address when reporting an error address
belonging to a CC6 state save area. Add a workaround to detect this
condition and compute the actual DRAM address of the error as documented
in the Revision Guide for AMD Family 15h Models 00h-0Fh Processors.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F15h and later use a portion of DRAM as a CC6 storage area. BIOS
programs D18F1x[17C:140,7C:40] DRAM Base/Limit accordingly by
subtracting the storage area from the DRAM limit setting. However, in
order for edac to consider that part of DRAM too, we need to include it
into the per-node range.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This warning was wrongfully added for a normal condition - intlvsel
actually selects the destination node when node interleaving is enabled
and it is not a mismatch. For a detailed example, see section 2.8.10.2
"Node Interleaving" in F10h BKDG.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This patch adds the TCO Watchdog DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is at least one BIOS with a DSDT containing a power resource
object with a _PR0 entry pointing back to that power resource. In
consequence, while registering that power resource
acpi_bus_get_power_flags() sees that it depends on itself and tries
to register it again, which leads to an infinitely deep recurrence.
This problem was introduced by commit bf325f9538d8c89312be305b9779e
(ACPI / PM: Register power resource devices as soon as they are
needed).
To fix this problem use the observation that power resources cannot
be power manageable and prevent acpi_bus_get_power_flags() from
being called for power resource objects.
References: https://bugzilla.kernel.org/show_bug.cgi?id=31872
Reported-and-tested-by: Pascal Dormeau <pdormeau@free.fr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <lenb@kernel.org>
Cc: stable@kernel.org
It turns out that some PCI devices are only found to be
wakeup-capable during registration, in which case, when
device_set_wakeup_capable() is called, device_is_registered() already
returns 'true' for the given device, but dpm_sysfs_add() hasn't been
called for it yet. This leads to situations in which the device's
power.can_wakeup flag is not set as requested because of failing
wakeup_sysfs_add() and its wakeup-related sysfs files are not
created, although they should be present. This is a post-2.6.38
regression introduced by commit cb8f51bdadb7969139c2e39c2defd4cde98c1
(PM: Do not create wakeup sysfs files for devices that cannot wake
up).
To work around this problem initialize the device's power.entry
field to an empty list head and make device_set_wakeup_capable()
check if it is still empty before attempting to add the devices
wakeup-related sysfs files with wakeup_sysfs_add(). Namely, if
power.entry is still empty at this point, device_pm_add() hasn't been
called yet for the device and its wakeup-related files will be
created later, so device_set_wakeup_capable() doesn't have to create
them.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
intel_sst drivers need to #include <linux/delay.h> so that
they build cleanly:
drivers/staging/intel_sst/intelmid_v1_control.c:188: error: implicit declaration of function 'msleep'
drivers/staging/intel_sst/intelmid_v2_control.c:172: error: implicit declaration of function 'msleep'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Harsha Priya <priya.harsha@intel.com>
Cc: KP Jeeja <jeeja.kp@intel.com>
Cc: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a build error when SND_PCM is not set
by adding a select statment.
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Acked-By: Ben Collins <bcollins@bluecherry.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vhci_rx/vhci_tx threads are created once but stopped each
time the vdev is shut down. On subsequent attach wake_up_process()
oopses trying to access the stopped threads.
This patch does as before the kthread conversion which is to
create the threads each time a device is attached and stop the
threads when the device is shut down.
Signed-off-by: Max Vozeler <max@hinterhof.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Arjan Mels <arjan.mels@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ft1000-pcmcia uses EXPORT_SYMBOL unnecessarily for sharing symbols
inside the same module. For some reason, this is causing section
conflicts on ia64 as well, even though neither are static.
error: __ksymtab_stop_ft1000_card causes a section type conflict
error: __ksymtab_init_ft1000_card causes a section type conflict
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a number of the following warnings:
warning: "CONFIG_RTS_PSTOR_DEBUG" is not defined
The code uses '#if CONFIG_RTS_PSTOR_DEBUG' when it should be using '#ifdef'
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a few files in the rts_pstor driver that use vmalloc/vfree without
including the header for it.
This patch adds <linux/vmalloc.h> to those files.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The gma500 driver calls set_pages_uc, which is an x86 pageattr call.
Since this driver is only used with Intel x86 motherboard chipsets,
make the driver depend on X86.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The olpc dcon xo1 driver uses udelay() without including <linux/delay.h>.
This patch adds it.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andres Salomon <dilinger@queued.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The default maximum transmit length for NCM USB frames should be so
that a short packet happens at the end if the device supports a length
greater than the defined maximum. This is achieved by adding 4 bytes
to the maximum length so that the existing logic can fit a short
packet there.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a code path in pmcraid that can be reached via device ioctl that
causes all sorts of ugliness, including heap corruption or triggering
the OOM killer due to consecutive allocation of large numbers of pages.
Not especially relevant from a security perspective, since users must
have CAP_SYS_ADMIN to open the character device.
First, the user can call pmcraid_chr_ioctl() with a type
PMCRAID_PASSTHROUGH_IOCTL. A pmcraid_passthrough_ioctl_buffer
is copied in, and the request_size variable is set to
buffer->ioarcb.data_transfer_length, which is an arbitrary 32-bit signed
value provided by the user.
If a negative value is provided here, bad things can happen. For
example, pmcraid_build_passthrough_ioadls() is called with this
request_size, which immediately calls pmcraid_alloc_sglist() with a
negative size. The resulting math on allocating a scatter list can
result in an overflow in the kzalloc() call (if num_elem is 0, the
sglist will be smaller than expected), or if num_elem is unexpectedly
large the subsequent loop will call alloc_pages() repeatedly, a high
number of pages will be allocated and the OOM killer might be invoked.
Prevent this value from being negative in pmcraid_ioctl_passthrough().
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable@kernel.org
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
SCSI uses request_queue->queuedata == NULL as a signal that the queue
is dying. We set this state in the sdev release function. However,
this allows a small window where we release the last reference but
haven't quite got to this stage yet and so something will try to take
a reference in scsi_request_fn and oops. It's very rare, but we had a
report here, so we're pushing this as a bug fix
The actual fix is to set request_queue->queuedata to NULL in
scsi_remove_device() before we drop the reference. This causes
correct automatic rejects from scsi_request_fn as people who hold
additional references try to submit work and prevents anything from
getting a new reference to the sdev that way.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit db422318cbca55168cf965f655471dbf8be82433 ([SCSI] scsi_dh:
propagate SCSI device deletion) introduced a regression where the device
reference is not dropped prior to scsi_dh_activate's early return from
the error path.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org # 2.6.38
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
At two points in handling device ioctls via /dev/mpt2ctl, user-supplied
length values are used to copy data from userspace into heap buffers
without bounds checking, allowing controllable heap corruption and
subsequently privilege escalation.
Additionally, user-supplied values are used to determine the size of a
copy_to_user() as well as the offset into the buffer to be read, with no
bounds checking, allowing users to read arbitrary kernel memory.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable@kernel.org
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The firmware is cached during the first successfull call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
So far the firmware is optional : a failure to load the firmware does
not prevent open() to success. It is thus necessary to 1) unregister
all 816x / 810[23] devices and 2) force a driver probe to issue a new
firmware load.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
At the end of section 10.1 of AHCI spec (rev 1.3), it states
Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h
Even though most AHCI host controller works without this check,
specific controller will fail under this condition.
Signed-off-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was
forgotten for "initial_timing" initialisation. This patch fixes such a problem.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The AT91SAM9 microcontrollers with master clock higher then 105 MHz
and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This
lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver
does not detect ATA device.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previously submitted patch was word-wrapped.
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previously submitted patch was word-wrapped.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther
Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 4a5610a04d415ed94af75bb1159d2621d62c8328 fixed an issue with
the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
reported a similar issue with his DVR-216D that the NOSETXFER horkage
worked around for him as well.
This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.
The issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=679143
Reported-by: Volodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.
Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM
is used. Implement ATA_FLAG_NO_DIPM and apply it.
This problem was reported by Stefan Bader in the following thread.
http://thread.gmane.org/gmane.linux.ide/48841
stable: applicable to 2.6.37 and 38.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed packets parameters for FW in UDP checksum offload flow.
Do not dereference TCP headers on non TCP frames.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/n_gsm: fix bug in CRC calculation for gsm1 mode
serial/imx: read cts state only after acking cts change irq
parport_pc.c: correctly release the requested region for the IT887x
A deadlock was reported to me recently that occured when netconsole was being
used in a virtual guest. If the virtio_net driver was removed while netconsole
was setup to use an interface that was driven by that driver, the guest
deadlocked. No backtrace was provided because netconsole was the only console
configured, but it became clear pretty quickly what the problem was. In
netconsole_netdev_event, if we get an unregister event, we call
__netpoll_cleanup with the target_list_lock held and irqs disabled.
__netpoll_cleanup can, if pending netpoll packets are waiting call
cancel_delayed_work_sync, which is a sleeping path. the might_sleep call in
that path gets triggered, causing a console warning to be issued. The
netconsole write handler of course tries to take the target_list_lock again,
which we already hold, causing deadlock.
The fix is pretty striaghtforward. Simply drop the target_list_lock and
re-enable irqs prior to calling __netpoll_cleanup, the re-acquire the lock, and
restart the loop. Confirmed by myself to fix the problem reported.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mechanism used to initiate work events from the interrupt
handler has a classic read/modify/write race between the interrupt
handler that sets the condition, and the worker task that reads and
clears the condition. Close these races by using atomic
bit fields.
Cc: stable@kernel.org
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 609ff3b ("be2net: add code to display temperature of ASIC")
adds support to display temperature of ASIC but there is missing
increment of work_counter in be_worker. Because of this 1) the
function be_cmd_get_die_temperature is called every 1 second instead
of every 32 seconds 2) be_cmd_get_die_temperature is called, although
it is not supported. This patch fixes this bug.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In-kernel disk event polling doesn't matter for legacy/fringe drivers
and may lead to infinite event loop if ->check_events() implementation
generates events on level condition instead of edge.
Now that block layer supports suppressing exporting unlisted events,
simply leaving disk->events cleared allows these drivers to keep the
internal revalidation behavior intact while avoiding weird
interactions with userland event handler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd and ide-cd
block: don't propagate unlisted DISK_EVENTs to userland
elevator: check for ELEVATOR_INSERT_SORT_MERGE in !elvpriv case too
check_events() implementations in both ide-gd and ide-cd are
inadequate for in-kernel event polling. Both generate media change
events continuously when certain conditions are met causing infinite
event loop between the driver and userland event handler.
As disk event now supports suppression of unlisted events, simply
de-listing DISK_EVENT_MEDIA_CHANGE from disk->events resolves the
problem. Internal handling around media revalidation will behave the
same while userland will fall back to userland event polling after
detecting the device doesn't support disk events.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jens Axboe <jaxboe@fusionio.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Change <sectors> from unsigned long long to sector_t.
This matches its source field.
ERROR: "__udivdi3" [drivers/md/raid456.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: console: Enable call to hvc_remove() on console port remove
virtio_pci: Prevent double-free of pci regions after device hot-unplug
virtio: Decrement avail idx on buffer detach
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
agp: fix arbitrary kernel memory writes
agp: fix OOM and buffer overflow
drm/radeon/kms: fix IH writeback on r6xx+ on big endian machines
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Initialise g4x watermarks for disabled pipes
drm/i915: Sanitize the output registers after resume
drm/i915/tv: Fix modeset flickering introduced in 7f58aabc3
drm/i915/tv: Only poll for TV connections
drm/i915/tv: Remember the detected TV type
* git://git.infradead.org/iommu-2.6:
intel_iommu: disable all VT-d PMRs when TXT launched
intel-iommu: Fix get_domain_for_dev() error path
intel-iommu: Unlink domain from iommu
intel-iommu: Fix use after release during device attach
This call was disabled as hot-unplugging one virtconsole port led to
another virtconsole port freezing.
Upon testing it again, this now works, so enable it.
In addition, a bug was found in qemu wherein removing a port of one type
caused the guest output from another port to stop working. I doubt it
was just this bug that caused it (since disabling the hvc_remove() call
did allow other ports to continue working), but since it's all solved
now, we're fine with hot-unplugging of virtconsole ports.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
