IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This provides some of the same info found in
the ath9k_htc debugfs through the standard ethtool stats API.
This logic is only supported when ath9k_htc debugfs kernel
feature is enabled, since that is the only time stats
are actually gathered.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 and CUS230 are similar cards, both
are AR9485 + xLNA solutions. But, the subsystem IDs
differ - identify CUS230 explicitly to make things
clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the REGULATORY debug level to print the target power
details. EEPROM can be used for other purposes and this
spams the log.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix ANI monitoring" reverted an earlier
commit that adjusted ANI to improve performance. But, this causes
adverse effects in AP mode (as reported by Felix based on an OpenWrt
report). Use the older INI/period configuration for now until more
testing is done.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Add custom parameters for CUS198" didn't
pass the correct gpio value to ath9k_hw_cfg_output(). Fix it.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.
Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201
Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since raising/lowering the limits based on INI has
been changed, the error limit for OFDM has to be 1000,
not 3500.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commits,
"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"
attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:
"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".
This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.
When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9485 boards with XLNA, the default gpio config
is not set correctly, fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All known ar7010+ar* device and current FW support STBC TX. This patch
make use of it and suggest to send STBC if peer support it.
I use wort "suggest" since currenly we have separate rate controller
in FW which will make decision based on rate and hardware.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CAB (Content after Beacon) queue is used for beacon-triggered
transmission of buffered multicast frames. If lots of multicast frames
were buffered and this queue fills up, it drowns out all regular
traffic. To limit the damage that buffered traffic can do, try to limit
the queued data to becaon_interval / 8.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for PS-Poll and U-APSD driver-buffered frames (part of
an aggregation session).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the UAPSD hardware queue to get PS-Poll responses out as fast as
possible and without backoff.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The phy error mask registers are programmed already
in ath9k_ani_restart(), so there is no need to set them
in ath9k_ani_reset().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
removed code setting various phy registers holding threshold values.
This is likely required for OFDM weak signal detection to function
correctly, so add them, but skip AR9462 and AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
modified the immunity level tables for both CCK and OFDM. Fix them
so that the tables are in sync with the internal driver/codebase.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed various ANI operational parameters to address a specific
card/environment. This is not really applicable for other cards
in general usage.
As per internal documentation, lowering the immunity level can be
done only after 5 periods have passed and the CCK/OFDM errors are
below the low watermak threshold - which have been fixed at 300 and
400 respectively by the sytems team.
Raising the immunity level can be done when CCK/OFDM errors exceed
600 and 1000 (per second).
Set these values once during attach.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed the OFDM weak signal detection logic to disable it
for AP mode, which is not allowed. Fix this and enable it always
for AP mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 68d9e1fa24d9c7c2e527f49df8d18fb8cf0ec943
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Cc: rmanohar@qca.qualcomm.com
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macros ATH9K_ANI_USE_OFDM_WEAK_SIG can be removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check "enable_ani" is not required since it is always
set to true and the logic for disabling/enabling ANI via
debugfs is done at a higher layer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process and update the internal RSSI average, which
is used by ANI, after verifying that the received
frame has valid rate information.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch make use of STBC flag in DMA RX descriptor.
Only devices after ar9280 can provide this information.
If card support it we will set HAVE_STBC flag, to show
clint programm thet STBC is supported but not received.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
some flags used only outside of ath9k - In this case we can use
"enum mac80211_rx_flags" and pass it upstream without extra
conversation.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If any bins from the training data are skipped (i != max_index), the
calculated compensation curve gets distorted, and the signal will be
wildly overamplified. This may be the cause of the reported hardware
damage that was caused by PA predistortion (because of which PAPRD was
disabled by default).
When calculating the x_est, Y, theta values, the use of max_index and i
was reversed. i points to the bin index whereas max_index refers to the
index of the calculated arrays.
Note that PA predistortion is still disabled, it will be re-enabled
after it has been properly validated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
