IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If an error occurs in the k3_j72xx_bandgap_probe() function the memory
allocated to the 'ref_table' will not be released.
Add a err_free_ref_table step to the error path to free 'ref_table'
Fixes: 72b3fc61c752 ("thermal: k3_j72xx_bandgap: Add the bandgap driver support")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20220525213617.30002-1-bb@ti.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The trends DROP_FULL and RAISE_FULL are not used and were never used
in the past AFAICT. Remove these conditions as they seems to not be
handled anywhere.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220629151012.3115773-2-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The code is actually clampling the next cooling device state using the
lowest and highest states of the thermal instance.
That code can be replaced by the clamp() macro which does exactly the
same. It results in a simpler routine to read.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220629151012.3115773-1-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The get_trend function relies on the interrupt to set the raising or
dropping trend. However the interpolated temperature is already giving
the temperature information to the thermal framework which is able to
deduce the trend.
Remove the trend code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220616202537.303655-3-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The get_trend function does already what the generic framework does.
Remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://lore.kernel.org/r/20220616202537.303655-2-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
There is a get_trend function which is a wrapper to call a private
get_trend function. However, this private get_trend function is not
assigned anywhere.
Remove this dead code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Amit Kucheria <amitk@kernel.org>
Link: https://lore.kernel.org/r/20220616202537.303655-1-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When setting up a new board, a plain "Can't register thermal zone"
didn't help me much because the thermal zones in DT were all fine. I
just had a sensor entry too much in the parent TSC node. Reword the
failure/success messages to contain the sensor number to make it easier
to understand which sensor is affected. Example output now:
rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20220610200500.6727-1-wsa+renesas@sang-engineering.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove unneeded global variable devfreq_cooling_ops which is used only
as a copy pattern. Instead, extend the struct devfreq_cooling_device with
the needed ops structure. This also simplifies the allocation/free code
during the setup/cleanup.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-5-lukasz.luba@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The code has moved and left some comments stale. Update them where
there is a need.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-4-lukasz.luba@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Simplify the thermal_power_cpu_get_power trace event by removing
complicated cpumask and variable length array. Now the tools parsing trace
output don't have to hassle to get this power data. The simplified format
version uses 'policy->cpu'. Remove also the 'load' information completely
since there is very little value of it in this trace event. To get the
CPUs' load (or utilization) there are other dedicated trace hooks in the
kernel. This patch also simplifies and speeds-up the main cooling code
when that trace event is enabled.
Rename the trace event to avoid confusion of tools which parse the trace
file.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20220613124327.30766-3-lukasz.luba@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It is very unlikely that one CPU cluster would have the EM and some other
won't have it (because EM registration failed or DT lacks needed entry).
Although, we should avoid modifying global variable with callbacks anyway.
Redesign this and add safety for such situation.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220613124327.30766-2-lukasz.luba@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Walleij)
- Fix grammar typo in the ARM global timer Kconfig option (Randy
Dunlap)
- Add the tegra186 timer and use it on the tegra234 board (Thierry
Reding)
- Add the 'CPUXGPT' CPU timer for Mediatek MT6795 and implement a
workaround to overcome an ATF bug where the timer is not correctly
initialized (AngeloGioacchino Del Regno)
- Rework the suspend/resume approach to enable the feature on the
timer even it is not an active clock and fix a compilation warning
(Claudiu Beznea)
- Add the Add R-Car Gen4 timer support along with the DT bindings
(Wolfram Sang)
- Add compatible for ti,am654-timer to support AM6 SoC (Tony Lindgren)
- Fix Kconfig option to put it back to 'bool' instead of 'tristate'
for the tegra186 (Daniel Lezcano)
- Sort 'family,type' DT bindings for the Renesas timers (Geert
Uytterhoeven)
- Add compatible 'allwinner,sun20i-d1-timer' for Allwinner D1 (Samuel
Holland)
- Remove unnecessary (void*) conversions for sun4i (XU pengfei)
- Remove unnecessary (void*) conversions for sun5i (Li zeming)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmLhWF0ACgkQqDIjiipP
6E+ziAgArY8BJ/09w4rt63LDO5nynorr0+Uuf0E9hCmc0KzRsSF3hO39EcuLj1zD
ubKKSXwaOucAcRYj7gCeqaSk/IOs9EmwESRVtLLIwEwYsg44iC1vmq4pJ8cX66qN
h5TqkOiq77fPIY3BR/nSFxddmlU2farO8oSUqdLNsVrqoIq2rttaQYADdYGa4LYn
dvQHEmh6jvJRoZM3aR6It0EWM7pyHKxAWFChWv+SbikheDCgIcugz+FUTy9lyhmf
39wLm2srmrCLbjaGdJnyc38/y/UPIJ0aqeSf7XSiHTWQ+dfNBfdbrmPTSJHiyIt+
iPrlx0ShvrMXeOxgbSxse53e+9Q88w==
=ApcN
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.20-rc1' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clockevent/source updates from Daniel Lezcano:
- Add the missing DT bindings for the MTU nomadik timer (Linus
Walleij)
- Fix grammar typo in the ARM global timer Kconfig option (Randy
Dunlap)
- Add the tegra186 timer and use it on the tegra234 board (Thierry
Reding)
- Add the 'CPUXGPT' CPU timer for Mediatek MT6795 and implement a
workaround to overcome an ATF bug where the timer is not correctly
initialized (AngeloGioacchino Del Regno)
- Rework the suspend/resume approach to enable the feature on the
timer even it is not an active clock and fix a compilation warning
(Claudiu Beznea)
- Add the Add R-Car Gen4 timer support along with the DT bindings
(Wolfram Sang)
- Add compatible for ti,am654-timer to support AM6 SoC (Tony Lindgren)
- Fix Kconfig option to put it back to 'bool' instead of 'tristate'
for the tegra186 (Daniel Lezcano)
- Sort 'family,type' DT bindings for the Renesas timers (Geert
Uytterhoeven)
- Add compatible 'allwinner,sun20i-d1-timer' for Allwinner D1 (Samuel
Holland)
- Remove unnecessary (void*) conversions for sun4i (XU pengfei)
- Remove unnecessary (void*) conversions for sun5i (Li zeming)
Link: https://lore.kernel.org/all/7472984e-f502-5f27-82bf-070127dd85a5@linaro.org
If ACPI_FADT_LOW_POWER_S0 is not set, this doesn't mean that low-power
S0 idle is not usable. It merely means that using S3 on the given
system is more beneficial from the energy saving perspective than using
low-power S0 idle, as long as S3 is supported.
Suspend-to-idle is still a valid suspend mode if ACPI_FADT_LOW_POWER_S0
is not set and the pm_suspend_via_firmware() check in pch_wpt_suspend()
is sufficient to distinguish suspend-to-idle from S3, so drop the
confusing ACPI_FADT_LOW_POWER_S0 check.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.
Update all EM users which access 'power' field and assume the value is
in milli-Watts.
Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.
Example calculation which shows the rounding error and impact:
power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz
power_a_uW = (100 * 600mW * 600mW * 500MHz) / 10^6 = 18000
power_a_mW = (100 * 600mW * 600mW * 500MHz) / 10^9 = 18
power_b_uW = (100 * 605mW * 605mW * 600MHz) / 10^6 = 21961
power_b_mW = (100 * 605mW * 605mW * 600MHz) / 10^9 = 21
max_freq = 2000MHz
cost_a_mW = 18 * 2000MHz/500MHz = 72
cost_a_uW = 18000 * 2000MHz/500MHz = 72000
cost_b_mW = 21 * 2000MHz/600MHz = 70 // <- artificially better
cost_b_uW = 21961 * 2000MHz/600MHz = 73203
The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is an unexpected word 'is' in a comments that need to be dropped
file: ./drivers/thermal/intel/x86_pkg_temp_thermal.c
line: 108
* tj-max is is interesting because threshold is set relative to this
changed to:
* tj-max is interesting because threshold is set relative to this
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a new CPU ID to the list of supported processors in the
intel_tcc_cooling driver (Sumeet Pawnikar).
-----BEGIN PGP SIGNATURE-----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=F4yU
-----END PGP SIGNATURE-----
Merge tag 'thermal-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Add a new CPU ID to the list of supported processors in the
intel_tcc_cooling driver (Sumeet Pawnikar)"
* tag 'thermal-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel_tcc_cooling: Add TCC cooling support for RaptorLake
Add RaptorLake to the list of processor models supported by the Intel
TCC cooling driver.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
[ rjw: Subject edits, new changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
effective_cpu_util() already has a `int cpu' parameter which allows to
retrieve the CPU capacity scale factor (or maximum CPU capacity) inside
this function via an arch_scale_cpu_capacity(cpu).
A lot of code calling effective_cpu_util() (or the shim
sched_cpu_util()) needs the maximum CPU capacity, i.e. it will call
arch_scale_cpu_capacity() already.
But not having to pass it into effective_cpu_util() will make the EAS
wake-up code easier, especially when the maximum CPU capacity reduced
by the thermal pressure is passed through the EAS wake-up functions.
Due to the asymmetric CPU capacity support of arm/arm64 architectures,
arch_scale_cpu_capacity(int cpu) is a per-CPU variable read access via
per_cpu(cpu_scale, cpu) on such a system.
On all other architectures it is a a compile-time constant
(SCHED_CAPACITY_SCALE).
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-4-vdonnefort@google.com
Use ida_alloc()/ida_free() instead of deprecated
ida_simple_get()/ida_simple_remove() as recommended.
Signed-off-by: keliu <liuke94@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Meteor Lake PCI device ID to the int340x thermal control
driver (Sumeet Pawnikar).
-----BEGIN PGP SIGNATURE-----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=lIzD
-----END PGP SIGNATURE-----
Merge tag 'thermal-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull additional thermal control update from Rafael Wysocki:
"Add Meteor Lake PCI device ID to the int340x thermal control driver
(Sumeet Pawnikar)"
* tag 'thermal-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: Add Meteor Lake PCI device ID
Add Meteor Lake PCI ID for processor thermal device.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add thermal library and thermal tools to encapsulate the netlink
into event based callbacks (Daniel Lezcano, Jiapeng Chong).
- Improve overheat condition handling during suspend-to-idle in the
Intel PCH thermal driver (Zhang Rui).
- Use local ops instead of global ops in devfreq_cooling (Kant Fan).
- Clean up _OSC handling in int340x (Davidlohr Bueso).
- Switch hisi_termal from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
(Hesham Almatary).
- Add new k3 j72xx bangdap driver and the corresponding bindings
(Keerthy).
- Fix missing of_node_put() in the SC iMX driver at probe time
(Miaoqian Lin).
- Fix memory leak in __thermal_cooling_device_register() when
device_register() fails by calling thermal_cooling_device_destroy_sysfs()
(Yang Yingliang).
- Add sc8180x and sc8280xp compatible string in the DT bindings and
lMH support for QCom tsens driver (Bjorn Andersson).
- Fix OTP Calibration Register values conforming to the documentation
on RZ/G2L and bindings documentation for RZ/G2UL (Biju Das).
- Fix type in kerneldoc description for __thermal_bind_params (Corentin
Labbe).
- Fix potential NULL dereference in sr_thermal_probe() on Broadcom
platform (Zheng Yongjun).
- Add change mode ops to the thermal-of sensor (Manaf Meethalavalappu
Pallikunhi).
- Fix non-negative value support by preventing the value to be clamp
to zero (Stefan Wahren).
- Add compatible string and DT bindings for MSM8960 tsens driver
(Dmitry Baryshkov).
- Add hwmon support for K3 driver (Massimiliano Minella).
- Refactor and add multiple generations support for QCom ADC driver
(Jishnu Prakash).
- Use platform_get_irq_optional() to get the interrupt on RCar driver and
document Document RZ/V2L bindings (Lad Prabhakar).
- Remove NULL check after container_of() call from the Intel HFI
thermal driver (Haowen Bai).
-----BEGIN PGP SIGNATURE-----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=3ltV
-----END PGP SIGNATURE-----
Merge tag 'thermal-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These add a thermal library and thermal tools to wrap the netlink
interface into event-based callbacks, improve overheat condition
handling during suspend-to-idle on Intel SoCs, add some new hardware
support, fix bugs and clean up code.
Specifics:
- Add thermal library and thermal tools to encapsulate the netlink
into event based callbacks (Daniel Lezcano, Jiapeng Chong).
- Improve overheat condition handling during suspend-to-idle in the
Intel PCH thermal driver (Zhang Rui).
- Use local ops instead of global ops in devfreq_cooling (Kant Fan).
- Clean up _OSC handling in int340x (Davidlohr Bueso).
- Switch hisi_termal from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
(Hesham Almatary).
- Add new k3 j72xx bangdap driver and the corresponding bindings
(Keerthy).
- Fix missing of_node_put() in the SC iMX driver at probe time
(Miaoqian Lin).
- Fix memory leak in __thermal_cooling_device_register()
when device_register() fails by calling
thermal_cooling_device_destroy_sysfs() (Yang Yingliang).
- Add sc8180x and sc8280xp compatible string in the DT bindings and
lMH support for QCom tsens driver (Bjorn Andersson).
- Fix OTP Calibration Register values conforming to the documentation
on RZ/G2L and bindings documentation for RZ/G2UL (Biju Das).
- Fix type in kerneldoc description for __thermal_bind_params
(Corentin Labbe).
- Fix potential NULL dereference in sr_thermal_probe() on Broadcom
platform (Zheng Yongjun).
- Add change mode ops to the thermal-of sensor (Manaf Meethalavalappu
Pallikunhi).
- Fix non-negative value support by preventing the value to be clamp
to zero (Stefan Wahren).
- Add compatible string and DT bindings for MSM8960 tsens driver
(Dmitry Baryshkov).
- Add hwmon support for K3 driver (Massimiliano Minella).
- Refactor and add multiple generations support for QCom ADC driver
(Jishnu Prakash).
- Use platform_get_irq_optional() to get the interrupt on RCar driver
and document Document RZ/V2L bindings (Lad Prabhakar).
- Remove NULL check after container_of() call from the Intel HFI
thermal driver (Haowen Bai)"
* tag 'thermal-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (38 commits)
thermal: intel: pch: improve the cooling delay log
thermal: intel: pch: enhance overheat handling
thermal: intel: pch: move cooling delay to suspend_noirq phase
PM: wakeup: expose pm_wakeup_pending to modules
thermal: k3_j72xx_bandgap: Add the bandgap driver support
dt-bindings: thermal: k3-j72xx: Add VTM bindings documentation
thermal/drivers/imx_sc_thermal: Fix refcount leak in imx_sc_thermal_probe
thermal/core: Fix memory leak in __thermal_cooling_device_register()
dt-bindings: thermal: tsens: Add sc8280xp compatible
dt-bindings: thermal: lmh: Add Qualcomm sc8180x compatible
thermal/drivers/qcom/lmh: Add sc8180x compatible
thermal/drivers/rz2gl: Fix OTP Calibration Register values
dt-bindings: thermal: rzg2l-thermal: Document RZ/G2UL bindings
thermal: thermal_of: fix typo on __thermal_bind_params
tools/thermal: remove unneeded semicolon
tools/lib/thermal: remove unneeded semicolon
thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe
tools/thermal: Add thermal daemon skeleton
tools/thermal: Add a temperature capture tool
tools/thermal: Add util library
...
- Update the Energy Model support code to allow the Energy Model to be
artificial, which means that the power values may not be on a uniform
scale with other devices providing power information, and update the
cpufreq_cooling and devfreq_cooling thermal drivers to support
artificial Energy Models (Lukasz Luba).
- Make DTPM check the Energy Model type (Lukasz Luba).
- Fix policy counter decrementation in cpufreq if Energy Model is in
use (Pierre Gondois).
- Add CPU-based scaling support to passive devfreq governor (Saravana
Kannan, Chanwoo Choi).
- Update the rk3399_dmc devfreq driver (Brian Norris).
- Export dev_pm_ops instead of suspend() and resume() in the IIO
chemical scd30 driver (Jonathan Cameron).
- Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
PM-runtime counterparts (Jonathan Cameron).
- Move symbol exports in the IIO chemical scd30 driver into the
IIO_SCD30 namespace (Jonathan Cameron).
- Avoid device PM-runtime usage count underflows (Rafael Wysocki).
- Allow dynamic debug to control printing of PM messages (David
Cohen).
- Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
Bai).
- Preserve ACPI-table override during hibernation (Amadeusz Sławiński).
- Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).
- Make Intel RAPL power capping driver support the RaptorLake and
AlderLake N processors (Zhang Rui, Sumeet Pawnikar).
- Remove redundant store to value after multiply in the RAPL power
capping driver (Colin Ian King).
- Add AlderLake processor support to the intel_idle driver (Zhang Rui).
- Fix regression leading to no genpd governor in the PSCI cpuidle
driver and fix the riscv-sbi cpuidle driver to allow a genpd
governor to be used (Ulf Hansson).
- Fix cpufreq governor clean up code to avoid using kfree() directly
to free kobject-based items (Kevin Hao).
- Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe Leroy).
- Make intel_pstate notify frequency invariance code when no_turbo is
turned on and off (Chen Yu).
- Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
Pandruvada).
- Make cpufreq avoid unnecessary frequency updates due to mismatch
between hardware and the frequency table (Viresh Kumar).
- Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
code (Viresh Kumar).
- Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
calling convention for some driver callbacks consistent (Rafael
Wysocki).
- Avoid accessing half-initialized cpufreq policies from the show()
and store() sysfs functions (Schspa Shi).
- Rearrange cpufreq_offline() to make the calling convention for some
driver callbacks consistent (Schspa Shi).
- Update CPPC handling in cpufreq (Pierre Gondois).
- Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).
- Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
Hansson).
- Improve the way genpd deals with its governors (Ulf Hansson).
- Update the turbostat utility to version 2022.04.16 (Len Brown,
Dan Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen
Yu).
-----BEGIN PGP SIGNATURE-----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=Hewm
-----END PGP SIGNATURE-----
Merge tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add support for 'artificial' Energy Models in which power
numbers for different entities may be in different scales, add support
for some new hardware, fix bugs and clean up code in multiple places.
Specifics:
- Update the Energy Model support code to allow the Energy Model to
be artificial, which means that the power values may not be on a
uniform scale with other devices providing power information, and
update the cpufreq_cooling and devfreq_cooling thermal drivers to
support artificial Energy Models (Lukasz Luba).
- Make DTPM check the Energy Model type (Lukasz Luba).
- Fix policy counter decrementation in cpufreq if Energy Model is in
use (Pierre Gondois).
- Add CPU-based scaling support to passive devfreq governor (Saravana
Kannan, Chanwoo Choi).
- Update the rk3399_dmc devfreq driver (Brian Norris).
- Export dev_pm_ops instead of suspend() and resume() in the IIO
chemical scd30 driver (Jonathan Cameron).
- Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
PM-runtime counterparts (Jonathan Cameron).
- Move symbol exports in the IIO chemical scd30 driver into the
IIO_SCD30 namespace (Jonathan Cameron).
- Avoid device PM-runtime usage count underflows (Rafael Wysocki).
- Allow dynamic debug to control printing of PM messages (David
Cohen).
- Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
Bai).
- Preserve ACPI-table override during hibernation (Amadeusz
Sławiński).
- Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).
- Make Intel RAPL power capping driver support the RaptorLake and
AlderLake N processors (Zhang Rui, Sumeet Pawnikar).
- Remove redundant store to value after multiply in the RAPL power
capping driver (Colin Ian King).
- Add AlderLake processor support to the intel_idle driver (Zhang
Rui).
- Fix regression leading to no genpd governor in the PSCI cpuidle
driver and fix the riscv-sbi cpuidle driver to allow a genpd
governor to be used (Ulf Hansson).
- Fix cpufreq governor clean up code to avoid using kfree() directly
to free kobject-based items (Kevin Hao).
- Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe
Leroy).
- Make intel_pstate notify frequency invariance code when no_turbo is
turned on and off (Chen Yu).
- Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
Pandruvada).
- Make cpufreq avoid unnecessary frequency updates due to mismatch
between hardware and the frequency table (Viresh Kumar).
- Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
code (Viresh Kumar).
- Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
calling convention for some driver callbacks consistent (Rafael
Wysocki).
- Avoid accessing half-initialized cpufreq policies from the show()
and store() sysfs functions (Schspa Shi).
- Rearrange cpufreq_offline() to make the calling convention for some
driver callbacks consistent (Schspa Shi).
- Update CPPC handling in cpufreq (Pierre Gondois).
- Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).
- Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
Hansson).
- Improve the way genpd deals with its governors (Ulf Hansson).
- Update the turbostat utility to version 2022.04.16 (Len Brown, Dan
Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen Yu)"
* tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (94 commits)
PM: domains: Trust domain-idle-states from DT to be correct by genpd
PM: domains: Measure power-on/off latencies in genpd based on a governor
PM: domains: Allocate governor data dynamically based on a genpd governor
PM: domains: Clean up some code in pm_genpd_init() and genpd_remove()
PM: domains: Fix initialization of genpd's next_wakeup
PM: domains: Fixup QoS latency measurements for IRQ safe devices in genpd
PM: domains: Measure suspend/resume latencies in genpd based on governor
PM: domains: Move the next_wakeup variable into the struct gpd_timing_data
PM: domains: Allocate gpd_timing_data dynamically based on governor
PM: domains: Skip another warning in irq_safe_dev_in_sleep_domain()
PM: domains: Rename irq_safe_dev_in_no_sleep_domain() in genpd
PM: domains: Don't check PM_QOS_FLAG_NO_POWER_OFF in genpd
PM: domains: Drop redundant code for genpd always-on governor
PM: domains: Add GENPD_FLAG_RPM_ALWAYS_ON for the always-on governor
powercap: intel_rapl: remove redundant store to value after multiply
cpufreq: CPPC: Enable dvfs_possible_from_any_cpu
cpufreq: CPPC: Enable fast_switch
ACPI: CPPC: Assume no transition latency if no PCCT
ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
ACPI: CPPC: Check _OSC for flexible address space
...
- New drivers
- Driver for the Microchip LAN966x SoC
- PMBus driver for Infineon Digital Multi-phase xdp152 family controllers
- Chip support added to existing drivers
- asus-ec-sensors
- Support for ROG STRIX X570-E GAMING WIFI II, PRIME X470-PRO,
and ProArt X570 Creator WIFI
- External temperature sensor support for ASUS WS X570-ACE
- nct6775
- Support for I2C driver
- Support for ASUS PRO H410T / PRIME H410M-R / ROG X570-E GAMING WIFI II
- lm75
- Support for - Atmel AT30TS74
- pmbus/max16601
- Support for MAX16602
- aquacomputer_d5next
- Support for Aquacomputer Farbwerk
- Support for Aquacomputer Octo
- jc42
- Support for S-34TS04A
- Kernel API changes / clarifications
- The chip parameter of with_info API is now mandatory
- New hwmon_device_register_for_thermal API call for use by the thermal
subsystem
- Improvements
- PMBus and JC42 drivers now register with thermal subsystem
- PMBus drivers now support get_voltage/set_voltage power operations
- The adt7475 driver now supports pin configuration
- The lm90 driver now supports setting extended range temperatures
configuration with a devicetree property
- The dell-smm driver now registers as cooling device
- The OCC driver delays hwmon registration until requested by userspace
- Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----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=LA2x
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for the Microchip LAN966x SoC
- PMBus driver for Infineon Digital Multi-phase xdp152 family
controllers
Chip support added to existing drivers:
- asus-ec-sensors:
- Support for ROG STRIX X570-E GAMING WIFI II, PRIME X470-PRO, and
ProArt X570 Creator WIFI
- External temperature sensor support for ASUS WS X570-ACE
- nct6775:
- Support for I2C driver
- Support for ASUS PRO H410T / PRIME H410M-R /
ROG X570-E GAMING WIFI II
- lm75:
- Support for - Atmel AT30TS74
- pmbus/max16601:
- Support for MAX16602
- aquacomputer_d5next:
- Support for Aquacomputer Farbwerk
- Support for Aquacomputer Octo
- jc42:
- Support for S-34TS04A
Kernel API changes / clarifications:
- The chip parameter of with_info API is now mandatory
- New hwmon_device_register_for_thermal API call for use by the
thermal subsystem
Improvements:
- PMBus and JC42 drivers now register with thermal subsystem
- PMBus drivers now support get_voltage/set_voltage power operations
- The adt7475 driver now supports pin configuration
- The lm90 driver now supports setting extended range temperatures
configuration with a devicetree property
- The dell-smm driver now registers as cooling device
- The OCC driver delays hwmon registration until requested by
userspace
... and various other minor fixes and improvements"
* tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (71 commits)
hwmon: (aquacomputer_d5next) Fix an error handling path in aqc_probe()
hwmon: (sl28cpld) Fix typo in comment
hwmon: (pmbus) Check PEC support before reading other registers
hwmon: (dimmtemp) Fix bitmap handling
hwmon: (lm90) enable extended range according to DTS node
dt-bindings: hwmon: lm90: add ti,extended-range-enable property
dt-bindings: hwmon: lm90: add missing ti,tmp461
hwmon: (ibmaem) Directly use ida_alloc()/free()
hwmon: Directly use ida_alloc()/free()
hwmon: (asus-ec-sensors) fix Formula VIII definition
dt-bindings: trivial-devices: Add xdp152
hwmon: (sl28cpld-hwmon) Use HWMON_CHANNEL_INFO macro
hwmon: (pwm-fan) Use HWMON_CHANNEL_INFO macro
hwmon: (peci/dimmtemp) Use HWMON_CHANNEL_INFO macro
hwmon: (peci/cputemp) Use HWMON_CHANNEL_INFO macro
hwmon: (mr75203) Use HWMON_CHANNEL_INFO macro
hwmon: (ltc2992) Use HWMON_CHANNEL_INFO macro
hwmon: (as370-hwmon) Use HWMON_CHANNEL_INFO macro
hwmon: Make chip parameter for with_info API mandatory
thermal/drivers/thermal_hwmon: Use hwmon_device_register_for_thermal()
...
Marge Energy Model support updates and cpuidle updates for 5.19-rc1:
- Update the Energy Model support code to allow the Energy Model to be
artificial, which means that the power values may not be on a uniform
scale with other devices providing power information, and update the
cpufreq_cooling and devfreq_cooling thermal drivers to support
artificial Energy Models (Lukasz Luba).
- Make DTPM check the Energy Model type (Lukasz Luba).
- Fix policy counter decrementation in cpufreq if Energy Model is in
use (Pierre Gondois).
- Add AlderLake processor support to the intel_idle driver (Zhang Rui).
- Fix regression leading to no genpd governor in the PSCI cpuidle
driver and fix the riscv-sbi cpuidle driver to allow a genpd
governor to be used (Ulf Hansson).
* pm-em:
PM: EM: Decrement policy counter
powercap: DTPM: Check for Energy Model type
thermal: cooling: Check Energy Model type in cpufreq_cooling and devfreq_cooling
Documentation: EM: Add artificial EM registration description
PM: EM: Remove old debugfs files and print all 'flags'
PM: EM: Change the order of arguments in the .active_power() callback
PM: EM: Use the new .get_cost() callback while registering EM
PM: EM: Add artificial EM flag
PM: EM: Add .get_cost() callback
* pm-cpuidle:
cpuidle: riscv-sbi: Fix code to allow a genpd governor to be used
cpuidle: psci: Fix regression leading to no genpd governor
intel_idle: Add AlderLake support
The thermal subsystem registers a hwmon device without providing chip
information or sysfs attribute groups. While undesirable, it would be
difficult to change. On the other side, it abuses the
hwmon_device_register_with_info API by not providing that information.
Use new API specifically created for the thermal subsystem instead to
let us enforce the 'chip' parameter for other callers of
hwmon_device_register_with_info().
Acked-by: Rafael J . Wysocki <rafael@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Previously, during suspend, intel_pch_thermal driver logs for every
cooling iteration, about the current PCH temperature and number of cooling
iterations that have been tried, like below
[ 100.955526] intel_pch_thermal 0000:00:14.2: CPU-PCH current temp [53C] higher than the threshold temp [50C], sleep 1 times for 100 ms duration
[ 101.064156] intel_pch_thermal 0000:00:14.2: CPU-PCH current temp [53C] higher than the threshold temp [50C], sleep 2 times for 100 ms duration
After changing the default delay_cnt to 600, in practice, it is common to
see tens of the above messages if the system is suspended when PCH
overheats. Thus, change this log message from dev_warn to dev_dbg because
it is only useful when we want to check the temperature trend.
At the same time, there is always a one-line message given by the driver
with the patch applied, with below four possibilities.
1. PCH is cool, no cooling delay needed
[ 1791.902853] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [48C]
2. PCH overheats and becomes cool after the cooling delays
[ 1475.511617] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C] after 30700 ms delay
3. PCH still overheats after the overall cooling timeout
[ 2250.157487] intel_pch_thermal 0000:00:12.0: CPU-PCH is hot [60C] after 60000 ms delay. S0ix might fail
4. PCH aborts cooling because of wakeup event detected during the delay
[ 1933.639509] intel_pch_thermal 0000:00:12.0: Wakeup event detected, abort cooling
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit ef63b043ac ("thermal: intel: pch: fix S0ix failure due to PCH
temperature above threshold") introduces delay loop mechanism that allows
PCH temperature to go down below threshold during suspend so it won't
block S0ix. And the default overall delay timeout is 1 second.
However, in practice, we found that the time it takes to cool the PCH down
below threshold highly depends on the initial PCH temperature when the
delay starts, as well as the ambient temperature.
And in some cases, the 1 second delay is not sufficient. As a result, the
system stays in a shallower power state like PCx instead of S0ix, and
drains the battery power, without user' notice.
To make sure S0ix is not blocked by the PCH overheating, we
1. expand the default overall timeout to 60 seconds.
2. make sure the temperature is below threshold rather than equal to it.
At the same time, as the cooling delay can be much longer and many wakeup
events (ACPI Power Button press, USB mouse move, etc) becomes valid in the
suspend_noirq phase, add detection of wakeup event so that the driver
does not delay blindly when the system suspend is likely to abort soon.
This patch may introduce longer suspend time, but only in the cases when
the system overheats and Linux used to enter a shallower S2idle state,
say, PCx instead of S0ix.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move the PCH Thermal driver suspend callback to suspend_noirq to do
cooling while the system is more quiescent.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add VTM thermal support. In the Voltage Thermal Management
Module(VTM), K3 J72XX supplies a voltage reference and a temperature
sensor feature that are gathered in the band gap voltage and
temperature sensor (VBGAPTS) module. The band gap provides current and
voltage reference for its internal circuits and other analog IP
blocks. The analog-to-digital converter (ADC) produces an output value
that is proportional to the silicon temperature.
Currently reading temperatures only is supported. There are no
active/passive cooling agent supported.
J721e SoCs have errata i2128: https://www.ti.com/lit/pdf/sprz455
The VTM Temperature Monitors (TEMPSENSORs) are trimmed during production,
with the resulting values stored in software-readable registers. Software
should use these register values when translating the Temperature
Monitor output codes to temperature values.
It has an involved workaround. Software needs to read the error codes for
-40C, 30C, 125C from the efuse for each device & derive a new look up table
for adc to temperature conversion. Involved calculating slopes & constants
using 3 different straight line equations with adc refernce codes as the
y-axis & error codes in the x-axis.
-40C to 30C
30C to 125C
125C to 150C
With the above 2 line equations we derive the full look-up table to
workaround the errata i2128 for j721e SoC.
Tested temperature reading on J721e SoC & J7200 SoC.
[daniel.lezcano@linaro.org: Generate look-up tables run-time]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20220517172920.10857-3-j-keerthy@ti.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
of_find_node_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: e20db70dba ("thermal: imx_sc: add i.MX system controller thermal support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220517055121.18092-1-linmq006@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The LMh instances in the Qualcomm SC8180X platform looks to behave
similar to those in SM8150, add additional compatibles to allow
platform specific behavior to be added if needed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220502164504.3972938-1-bjorn.andersson@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
As per the latest RZ/G2L Hardware User's Manual (Rev.1.10 Apr, 2022),
the bit 31 of TSU OTP Calibration Register(OTPTSUTRIM) indicates
whether bit [11:0] of OTPTSUTRIM is valid or invalid.
This patch updates the code to reflect this change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220428093346.7552-1-biju.das.jz@bp.renesas.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add a missing s to __thermal_bind_param kernel doc comment.
This fixes the following sparse warnings:
drivers/thermal/thermal_of.c:50: warning: expecting prototype for struct __thermal_bind_param. Prototype was for struct __thermal_bind_params instead
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/20220426064113.3787826-1-clabbe@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The sensor driver which register through thermal_of interface doesn't
have an option to get thermal zone mode change notification from
thermal core.
Add support for change_mode ops in thermal_of interface so that sensor
driver can use this ops for mode change notification.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
Link: https://lore.kernel.org/r/1646767586-31908-1-git-send-email-quic_manafm@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The thermal sensor on BCM2711 is capable of negative temperatures, so don't
clamp the measurements at zero. Since this was the only use for variable t,
drop it.
This change based on a patch by Dom Cobley, who also tested the fix.
Fixes: 59b781352d ("thermal: Add BCM2711 thermal driver")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220412195423.104511-1-stefan.wahren@i2se.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
On apq8064 (msm8960) platforms the tsens device is created manually by
the gcc driver. Prepare the tsens driver for the qcom,msm8960-tsens
device instantiated from the device tree.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220406002648.393486-3-dmitry.baryshkov@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Expose the thermal sensors on K3 AM654 as hwmon devices, so that
temperatures could be read using lm-sensors.
Signed-off-by: Massimiliano Minella <massimiliano.minella@gmail.com>
Link: https://lore.kernel.org/r/20220401151656.913166-1-massimiliano.minella@se.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add support for PMIC5 Gen2 ADC_TM, used on PMIC7 chips. It is a
close counterpart of PMIC7 ADC and has the same functionality as
PMIC5 ADC_TM, for threshold monitoring and interrupt generation.
It is present on PMK8350 alone, like PMIC7 ADC and can be used
to monitor up to 8 ADC channels, from any of the PMIC7 PMICs
having ADC on a target, through PBS(Programmable Boot Sequence).
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/1648991869-20899-5-git-send-email-quic_jprakash@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Refactor code to support multiple generations of ADC_TM devices
by defining gen number, irq name and disable, configure, isr and
init APIs in the individual data structs.
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1648991869-20899-4-git-send-email-quic_jprakash@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220110144039.5810-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
container_of() will never return NULL, so remove useless code.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the new OS handshake introduced by commit: "c7ff29763989 ("thermal:
int340x: Update OS policy capability handshake")", the "enabled" thermal
zone mode doesn't work in the same way as previously.
The "enabled" mode fails with -EINVAL when the new handshake is used.
To address this issue, when the new OS UUID mask is set:
- When the mode is "enabled", return 0 as the firmware already has the
latest policy mask.
- When the mode is "disabled", update the firmware with the UUID mask
of zero.
This way, the firmware can take over the thermal control.
Also reset the OS UUID mask, which allows user space to update with new
set of policies.
Fixes: c7ff297639 ("thermal: int340x: Update OS policy capability handshake")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits, removed unneeded parens ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge a fix for the attr.show callback prototype in the int340x thermal
driver (Kees Cook).
* thermal-int340x:
thermal: int340x: Fix attr.show callback prototype
The userspace governor is still in use on production systems and the
deprecating warning is scary.
Even if we want to get rid of the userspace governor, it is too soon
yet as the alternatives are not yet adopted.
Change the deprecated warning by an information message suggesting to
switch to the netlink thermal events.
Fixes: 0275c9fb0e ("thermal/core: Make the userspace governor deprecated")
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit a67a46af4a.
It has been reported the warning is annoying as the cooling device
state is still needed on some production system.
Meanwhile we provide a way to consolidate the thermal framework to
prevent multiple actors acting on the cooling devices with conflicting
decisions, let's revert this warning.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Control Flow Integrity (CFI) instrumentation of the kernel noticed that
the caller, dev_attr_show(), and the callback, odvp_show(), did not have
matching function prototypes, which would cause a CFI exception to be
raised. Correct the prototype by using struct device_attribute instead
of struct kobj_attribute.
Reported-and-tested-by: Joao Moreira <joao@overdrivepizza.com>
Link: https://lore.kernel.org/lkml/067ce8bd4c3968054509831fa2347f4f@overdrivepizza.com/
Fixes: 006f006f1e ("thermal/int340x_thermal: Export OEM vendor variables")
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix access illegal address problem in following condition:
There are multiple devfreq cooling devices in system, some of them has
EM model but others do not. Energy model ops such as state2power will
append to global devfreq_cooling_ops when the cooling device with
EM model is registered. It makes the cooling device without EM model
also use devfreq_cooling_ops after appending when registered later by
of_devfreq_cooling_register_power() or of_devfreq_cooling_register().
The IPA governor regards the cooling devices without EM model as a power
actor, because they also have energy model ops, and will access illegal
address at dfc->em_pd when execute cdev->ops->get_requested_power,
cdev->ops->state2power or cdev->ops->power2state.
Fixes: 615510fe13 ("thermal: devfreq_cooling: remove old power model and use EM")
Cc: 5.13+ <stable@vger.kernel.org> # 5.13+
Signed-off-by: Kant Fan <kant@allwinnertech.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cleaning up the driver to use pm_sleep_ptr() macro instead of #ifdef
guards is simpler and allows the compiler to remove those functions
if built without CONFIG_PM_SLEEP support.
Signed-off-by: Hesham Almatary <hesham.almatary@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Energy Model can now be artificial, which means the power values
are mathematically generated to leverage EAS while not expected to be on
an uniform scale with other devices providing power information. If this
EM type is in use, the thermal governor IPA should not be allowed to
operate, since the relation between cooling devices is not properly
defined. Thus, it might be possible that big GPU has lower power values
than a Little CPU. To mitigate a misbehaviour of the thermal control
algorithm, simply do not register the cooling device as IPA's power
actor.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that the UUID is already sanitized by the caller,
lets trivially clean up some of the context arming.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a single point of freeing/exit after ensuring no error in
int3400_setup_gddv().
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is the caller's responsibility to free only upon ACPI_SUCCESS.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge Intel Hardware Feedback Interface (HFI) thermal driver for
5.18-rc1 and update the intel-speed-select utility to support that
driver.
* thermal-hfi:
tools/power/x86/intel-speed-select: v1.12 release
tools/power/x86/intel-speed-select: HFI support
tools/power/x86/intel-speed-select: OOB daemon mode
thermal: intel: hfi: INTEL_HFI_THERMAL depends on NET
thermal: netlink: Fix parameter type of thermal_genl_cpu_capability_event() stub
thermal: intel: hfi: Notify user space for HFI events
thermal: netlink: Add a new event to notify CPU capabilities change
thermal: intel: hfi: Enable notification interrupt
thermal: intel: hfi: Handle CPU hotplug events
thermal: intel: hfi: Minimally initialize the Hardware Feedback Interface
x86/cpu: Add definitions for the Intel Hardware Feedback Interface
x86/Documentation: Describe the Intel Hardware Feedback Interface
Merge powerclamp thermal driver changes, int340x thermal driver changes
and thermal documentation changes for 5.18-rc1:
- Don't use bitmap_weight() in end_power_clamp() in the powerclamp
driver (Yury Norov).
- Update the OS policy capabilities handshake in the int340x thermal
driver (Srinivas Pandruvada).
- Increase the policies bitmap size in int340x (Srinivas Pandruvada).
- Replace acpi_bus_get_device() with acpi_fetch_acpi_dev() in the
int340x thermal driver (Rafael Wysocki).
- Check for NULL after calling kmemdup() in int340x (Jiasheng Jiang).
- Add Intel Dynamic Power and Thermal Framework (DPTF) kernel interface
documentation (Srinivas Pandruvada).
- Fix bullet list warning in the thermal documentation (Randy Dunlap).
* thermal-powerclamp:
thermal: intel_powerclamp: don't use bitmap_weight() in end_power_clamp()
* thermal-int340x:
thermal: int340x: Update OS policy capability handshake
thermal: int340x: Increase bitmap size
thermal: Replace acpi_bus_get_device()
thermal: int340x: Check for NULL after calling kmemdup()
* thermal-docs:
Documentation: thermal: DPTF Documentation
thermal: fix Documentation bullet list warning
Update the firmware with OS supported policies mask, so that firmware can
relinquish its internal controls. Without this update several Tiger Lake
laptops gets performance limited with in few seconds of executing in
turbo region.
The existing way of enumerating firmware policies via IDSP method and
selecting policy by directly writing those policy UUIDS via _OSC method
is not supported in newer generation of hardware.
There is a new UUID "B23BA85D-C8B7-3542-88DE-8DE2FFCFD698" is defined for
updating policy capabilities. As part of ACPI _OSC method:
Arg0 - UUID: B23BA85D-C8B7-3542-88DE-8DE2FFCFD698
Arg1 - Rev ID: 1
Arg2 - Count: 2
Arg3 - Capability buffers: Array of Arg2 DWORDS
DWORD1: As defined in the ACPI 5.0 Specification
- Bit 0: Query Flag
- Bits 1-3: Always 0
- Bits 4-31: Reserved
DWORD2 and beyond:
- Bit0: set to 1 to indicate Intel(R) Dynamic Tuning is active, 0 to
indicate it is disabled and legacy thermal mechanism should
be enabled.
- Bit1: set to 1 to indicate Intel(R) Dynamic Tuning is controlling
active cooling, 0 to indicate bios shall enable legacy thermal
zone with active trip point.
- Bit2: set to 1 to indicate Intel(R) Dynamic Tuning is controlling
passive cooling, 0 to indicate bios shall enable legacy thermal
zone with passive trip point.
- Bit3: set to 1 to indicate Intel(R) Dynamic Tuning is handling
critical trip point, 0 to indicate bios shall enable legacy
thermal zone with critical trip point.
- Bits 4:31: Reserved
From sysfs interface, there is an existing interface to update policy
UUID using attribute "current_uuid". User space can write the same UUID
for ACTIVE, PASSIVE and CRITICAL policy. Driver converts these UUIDs to
DWORD2 Bit 1 to Bit 3. When any of the policy is activated by user
space it is assumed that dynamic tuning is active.
For example
$cd /sys/bus/platform/devices/INTC1040:00/uuids
To support active policy
$echo "3A95C389-E4B8-4629-A526-C52C88626BAE" > current_uuid
To support passive policy
$echo "42A441D6-AE6A-462b-A84B-4A8CE79027D3" > current_uuid
To support critical policy
$echo "97C68AE7-15FA-499c-B8C9-5DA81D606E0A" > current_uuid
To check all the supported policies
$cat current_uuid
3A95C389-E4B8-4629-A526-C52C88626BAE
42A441D6-AE6A-462b-A84B-4A8CE79027D3
97C68AE7-15FA-499c-B8C9-5DA81D606E0A
To match the bit format for DWORD2, rearranged enum int3400_thermal_uuid
and int3400_thermal_uuids[] by swapping current INT3400_THERMAL_ACTIVE
and INT3400_THERMAL_PASSIVE_1.
If the policies are enumerated via IDSP method then legacy method is
used, if not the new method is used to update policy support.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The number of policies are 10, so can't be supported by the bitmap size
of u8.
Even though there are no platfoms with these many policies, but
for correctness increase to u32.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 16fc8eca19 ("thermal/int340x_thermal: Add additional UUIDs")
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Utilize platform_get_irq_optional() to silence these messages:
brcmstb_thermal a581500.thermal: IRQ index 0 not found
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220301181412.2008044-1-f.fainelli@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The return value from tegra_bpmp_transfer indicates the success or
failure of the IPC transaction with BPMP. If the transaction
succeeded, we also need to check the actual command's result code.
Add code to do this.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210915085517.1669675-1-mperttunen@nvidia.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Expose ti-soc-thermal thermal sensors as HWMON devices.
# sensors
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +54.2 C (crit = +105.0 C)
dspeve_thermal-virtual-0
Adapter: Virtual device
temp1: +51.4 C (crit = +105.0 C)
gpu_thermal-virtual-0
Adapter: Virtual device
temp1: +54.2 C (crit = +105.0 C)
iva_thermal-virtual-0
Adapter: Virtual device
temp1: +54.6 C (crit = +105.0 C)
core_thermal-virtual-0
Adapter: Virtual device
temp1: +52.6 C (crit = +105.0 C)
Similar to imx_sc_thermal d2bc4dd91d.
No need to take care of thermal_remove_hwmon_sysfs() since
devm_thermal_add_hwmon_sysfs() (a wrapper around devres) is
used. See c7fc403e40.
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Link: https://lore.kernel.org/r/20220218104725.2718904-1-romain.naour@smile.fr
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add compatible to support LMh for sm8150 SoC.
sm8150 does not require explicit enabling for various LMh subsystems.
Add a variable indicating the same as match data which is set for sdm845.
Execute the piece of code enabling various LMh subsystems only if
enable algorithm match data is present.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220106173138.411097-2-thara.gopinath@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Register thermal zones as hwmon sensors to let userspace read
CPU temperatures using standard hwmon interface.
Acked-by: Amit Kucheria <amitk@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220129180750.1882310-1-dmitry.baryshkov@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Do not call get_trip_hyst() from thermal_genl_cmd_tz_get_trip() if
the thermal zone does not define one.
Fixes: 1ce50e7d40 ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
THERMAL_NETLINK depends on NET and since 'select' does not follow
any dependency chain, INTEL_HFI_THERMAL also should depend on NET.
Fix one Kconfig warning and 48 subsequent build errors:
WARNING: unmet direct dependencies detected for THERMAL_NETLINK
Depends on [n]: THERMAL [=y] && NET [=n]
Selected by [y]:
- INTEL_HFI_THERMAL [=y] && THERMAL [=y] && (X86 [=y] || X86_INTEL_QUARK [=n] || COMPILE_TEST [=y]) && CPU_SUP_INTEL [=y] && X86_THERMAL_VECTOR [=y]
Fixes: bd30cdfd9b ("thermal: intel: hfi: Notify user space for HFI events")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When building with CONFIG_THERMAL_NETLINK=n, there is a spew of warnings
along the lines of:
In file included from drivers/thermal/thermal_core.c:27:
In file included from drivers/thermal/thermal_core.h:15:
drivers/thermal/thermal_netlink.h:113:71: warning: declaration of 'struct cpu_capability' will not be visible outside of this function [-Wvisibility]
static inline int thermal_genl_cpu_capability_event(int count, struct cpu_capability *caps)
^
1 warning generated.
'struct cpu_capability' is not forward declared anywhere in the header.
As it turns out, this should really be 'struct thermal_genl_cpu_caps',
which silences the warning and makes the parameter types of the stub
match the full function.
Fixes: e4b1eb24ce ("thermal: netlink: Add a new event to notify CPU capabilities change")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Don't call bitmap_weight() if the following code can get by
without it.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the potential failure of the allocation, kmemdup() may return NULL.
Then, 'bin_attr_data_vault.private' will be NULL, but
'bin_attr_data_vault.size' is not 0, which is not consistent.
Therefore, it is better to check the return value of kmemdup() to
avoid the confusion.
Fixes: 0ba13c763a ("thermal/int340x_thermal: Export GDDV")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the hardware issues an HFI event, relay a notification to user space.
This allows user space to respond by reading performance and efficiency of
each CPU and take appropriate action.
For example, when the performance and efficiency of a CPU is 0, user space
can either offline the CPU or inject idle. Also, if user space notices a
downward trend in performance, it may proactively adjust power limits to
avoid future situations in which performance drops to 0.
To avoid excessive notifications, the rate is limited by one HZ per event.
To limit the netlink message size, send parameters for up to 16 CPUs in a
single message. If there are more than 16 CPUs, issue as many messages as
needed to notify the status of all CPUs.
In the HFI specification, both performance and efficiency capabilities are
defined in the [0, 255] range. The existing implementations of HFI hardware
do not scale the maximum values to 255. Since userspace cares about
capability values that are either 0 or show a downward/upward trend, this
fact does not matter much. Relative changes in capabilities are enough. To
comply with the thermal netlink ABI, scale both performance and efficiency
capabilities to the [0, 1023] interval.
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a new netlink event to notify change in CPU capabilities in terms of
performance and efficiency.
Firmware may change CPU capabilities as a result of thermal events in the
system or to account for changes in the TDP (thermal design power) level.
This notification type will allow user space to avoid running workloads
on certain CPUs or proactively adjust power limits to avoid future events.
The netlink message consists of a nested attribute
(THERMAL_GENL_ATTR_CPU_CAPABILITY) with three attributes:
* THERMAL_GENL_ATTR_CPU_CAPABILITY_ID (type u32):
-- logical CPU number
* THERMAL_GENL_ATTR_CPU_CAPABILITY_PERFORMANCE (type u32):
-- Scaled performance from 0-1023
* THERMAL_GENL_ATTR_CPU_CAPABILITY_EFFICIENCY (type u32):
-- Scaled efficiency from 0-1023
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When hardware wants to inform the operating system about updates in the HFI
table, it issues a package-level thermal event interrupt. For this,
hardware has new interrupt and status bits in the IA32_PACKAGE_THERM_
INTERRUPT and IA32_PACKAGE_THERM_STATUS registers. The existing thermal
throttle driver already handles thermal event interrupts: it initializes
the thermal vector of the local APIC as well as per-CPU and package-level
interrupt reporting. It also provides routines to service such interrupts.
Extend its functionality to also handle HFI interrupts.
The frequency of the thermal HFI interrupt is specific to each processor
model. On some processors, a single interrupt happens as soon as the HFI is
enabled and hardware will never update HFI capabilities afterwards. On
other processors, thermal and power constraints may cause thermal HFI
interrupts every tens of milliseconds.
To not overwhelm consumers of the HFI data, use delayed work to throttle
the rate at which HFI updates are processed. Use a dedicated workqueue to
not overload system_wq if hardware issues many HFI updates.
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All CPUs in a package are represented in an HFI table. There exists an
HFI table per package. Thus, CPUs in a package need to coordinate to
initialize and access the table. Do such coordination during CPU hotplug.
Use the first CPU to come online in a package to initialize the HFI
instance and the data structure representing it. Other CPUs in the same
package need only to register or unregister themselves in that data
structure.
The HFI depends on both the package-level thermal management and the local
APIC thermal local vector. Thus, to ensure that a CPU coming online has an
associated HFI instance when the hardware issues an HFI event, enable the
HFI only after having enabled the local APIC thermal vector. The thermal
throttle driver takes care of the needed package-level initialization.
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Intel Hardware Feedback Interface provides guidance to the operating
system about the performance and energy efficiency capabilities of each
CPU in the system. Capabilities are numbers between 0 and 255 where a
higher number represents a higher capability. For each CPU, energy
efficiency and performance are reported as separate capabilities.
Hardware computes these capabilities based on the operating conditions of
the system such as power and thermal limits. These capabilities are shared
with the operating system in a table resident in memory. Each package in
the system has its own HFI instance. Every logical CPU in the package is
represented in the table. More than one logical CPUs may be represented in
a single table entry. When the hardware updates the table, it generates a
package-level thermal interrupt.
The size and format of the HFI table depend on the supported features and
can only be determined at runtime. To minimally initialize the HFI, parse
its features and allocate one instance per package of a data structure with
the necessary parameters to read and navigate a local copy (i.e., owned by
the driver) of individual HFI tables.
A subsequent changeset will provide per-CPU initialization and interrupt
handling.
Reviewed-by: Len Brown <len.brown@intel.com>
Co-developed by: Aubrey Li <aubrey.li@linux.intel.com>
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Raptor Lake PCI ID for processor thermal device.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Raptor Lake ACPI IDs for DPTF devices.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add new TSU driver and DT bindings for the Renesas RZ/G2L platform
(Biju Das).
- Fix missing check when calling reset_control_deassert() in the
rz2gl thermal driver (Biju Das).
- In preparation for FORTIFY_SOURCE performing compile-time and
run-time field bounds checking for memcpy(), avoid intentionally
writing across neighboring fields in the int340x thermal control
driver (Kees Cook).
- Fix RFIM mailbox write commands handling in the int340x thermal
control driver (Sumeet Pawnikar).
- Fix PM issue occurring in the iMX thermal control driver during
suspend/resume by implementing PM runtime support in it (Oleksij
Rempel).
- Add 'const' annotation to thermal_cooling_ops in the Intel
powerclamp driver (Rikard Falkeborn).
- Fix missing ADC bit set in the iMX8MP thermal driver to enable the
sensor (Paul Gerber).
- Drop unused local variable definition from tmon (ran jianping).
-----BEGIN PGP SIGNATURE-----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=Crok
-----END PGP SIGNATURE-----
Merge tag 'thermal-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These add a new driver for Renesas RZ/G2L TSU, update a few existing
thermal control drivers and clean up the tmon utility.
Specifics:
- Add new TSU driver and DT bindings for the Renesas RZ/G2L platform
(Biju Das).
- Fix missing check when calling reset_control_deassert() in the
rz2gl thermal driver (Biju Das).
- In preparation for FORTIFY_SOURCE performing compile-time and
run-time field bounds checking for memcpy(), avoid intentionally
writing across neighboring fields in the int340x thermal control
driver (Kees Cook).
- Fix RFIM mailbox write commands handling in the int340x thermal
control driver (Sumeet Pawnikar).
- Fix PM issue occurring in the iMX thermal control driver during
suspend/resume by implementing PM runtime support in it (Oleksij
Rempel).
- Add 'const' annotation to thermal_cooling_ops in the Intel
powerclamp driver (Rikard Falkeborn).
- Fix missing ADC bit set in the iMX8MP thermal driver to enable the
sensor (Paul Gerber).
- Drop unused local variable definition from tmon (ran jianping)"
* tag 'thermal-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/drivers/int340x: Fix RFIM mailbox write commands
thermal/drivers/rz2gl: Add error check for reset_control_deassert()
thermal/drivers/imx8mm: Enable ADC when enabling monitor
thermal/drivers: Add TSU driver for RZ/G2L
dt-bindings: thermal: Document Renesas RZ/G2L TSU
thermal/drivers/intel_powerclamp: Constify static thermal_cooling_device_ops
thermal/drivers/imx: Implement runtime PM support
thermal: tools: tmon: remove unneeded local variable
thermal: int340x: Use struct_group() for memcpy() region
The existing mail mechanism only supports writing of workload types.
However, mailbox command for RFIM (cmd = 0x08) also requires write
operation which is ignored. This results in failing to store RFI
restriction.
Fixint this requires enhancing mailbox writes for non workload
commands too, so remove the check for MBOX_CMD_WORKLOAD_TYPE_WRITE
in mailbox write to allow this other write commands to be supoorted.
At the same time, however, we have to make sure that there is no
impact on read commands, by avoiding to write anything into the
mailbox data register.
To properly implement that, add two separate functions for mbox read
and write commands for the processor thermal workload command type.
This helps to distinguish the read and write workload command types
from each other while sending mbox commands.
Fixes: 5d6fbc96bd ("thermal/drivers/int340x: processor_thermal: Export additional attributes")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: 5.14+ <stable@vger.kernel.org> # 5.14+
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull ARM cpufreq updates for 5.17-rc1 from Viresh Kumar:
"- Qcom cpufreq driver updates improve irq support (Ard Biesheuvel, Stephen Boyd,
and Vladimir Zapolskiy).
- Fixes double devm_remap for mediatek driver (Hector Yuan).
- Introduces thermal pressure helpers (Lukasz Luba)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: mediatek-hw: Fix double devm_remap in hotplug case
cpufreq: qcom-hw: Use optional irq API
cpufreq: qcom-hw: Set CPU affinity of dcvsh interrupts
cpufreq: qcom-hw: Fix probable nested interrupt handling
cpufreq: qcom-cpufreq-hw: Avoid stack buffer for IRQ name
arch_topology: Remove unused topology_set_thermal_pressure() and related
cpufreq: qcom-cpufreq-hw: Use new thermal pressure update function
cpufreq: qcom-cpufreq-hw: Update offline CPUs per-cpu thermal pressure
thermal: cpufreq_cooling: Use new thermal pressure update function
arch_topology: Introduce thermal pressure update function
implementing PM runtime support (Oleksij Rempel)
- Add 'const' annotation to the thermal_cooling_ops in the Intel
powerclamp driver (Rikard Falkeborn)
- Add TSU driver and bindings for the RZ/G2L platform (Biju Das)
- Fix the missing ADC bit set on iMX8MP to enable the sensor (Paul
Gerber)
- Fix missing check when calling reset_control_deassert() (Biju Das)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmHEmTsACgkQqDIjiipP
6E/KMgf+MdzK/OTuxP+pf0yVqpC3WpH6lrNhBRC+mO4S0yAe8ZlYCFVVtvMftSrn
M2H8uxw74XlVkD8yi1kSYa1iVeD9jF+5ZViOybc83SKwryYEFI7tjxsjpaPFotxe
ZnL8y55hDC63YpwNeafGgW9M/JFehBP09zafakdVsvzzNGP8XKoYQcgyeofwNIrX
CRwU95K85k0eS2h9gPFPRWaNwZS4ubVEYr857oiGArX4/hEycvJ2UO+cH+zEmGjQ
QKJIEh5gQEBs2lKgcqUwzNbitm5lUG+rYRWD9omQ4QLtHK/fxZw2CMMVnNso/G5z
lslc8pLLwLh5QdR3v9tX4+OAxsV38A==
=uIVF
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.17-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal control material for 5.17-rc1 from Daniel Lezcano:
- Fix PM issue on the iMX driver when suspend/resume is happening by
implementing PM runtime support (Oleksij Rempel)
- Add 'const' annotation to the thermal_cooling_ops in the Intel
powerclamp driver (Rikard Falkeborn)
- Add TSU driver and bindings for the RZ/G2L platform (Biju Das)
- Fix missing ADC bit set on iMX8MP to enable the sensor (Paul Gerber)
- Fix missing check when calling reset_control_deassert() (Biju Das)
* tag 'thermal-v5.17-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal/drivers/rz2gl: Add error check for reset_control_deassert()
thermal/drivers/imx8mm: Enable ADC when enabling monitor
thermal/drivers: Add TSU driver for RZ/G2L
dt-bindings: thermal: Document Renesas RZ/G2L TSU
thermal/drivers/intel_powerclamp: Constify static thermal_cooling_device_ops
thermal/drivers/imx: Implement runtime PM support
If reset_control_deassert() fails, then we won't be able to access
the device registers. Therefore check the return code of
reset_control_deassert() and bail out in case of error.
While at it replace the parameter "&pdev->dev" -> "dev" in
devm_reset_control_get_exclusive().
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20211208164010.4130-1-biju.das.jz@bp.renesas.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The VCoRefLow CPU FIVR register definition for Tiger Lake is incorrect.
Current implementation reads it from MMIO offset 0x5A18 and bit
offset [12:14], but the actual correct register definition is from
bit offset [11:13].
Update to fix the bit offset.
Fixes: 473be51142 ("thermal: int340x: processor_thermal: Add RFIM driver")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: 5.14+ <stable@vger.kernel.org> # 5.14+
[ rjw: New subject, changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The i.MX 8MP has a ADC_PD bit in the TMU_TER register that controls the
operating mode of the ADC:
* 0 means normal operating mode
* 1 means power down mode
When enabling/disabling the TMU, the ADC operating mode must be set
accordingly.
i.MX 8M Mini & Nano are lacking this bit.
Signed-off-by: Paul Gerber <Paul.Gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 2b8f1f0337 ("thermal: imx8mm: Add i.MX8MP support")
Link: https://lore.kernel.org/r/20211122114225.196280-1-alexander.stein@ew.tq-group.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The RZ/G2L SoC incorporates a thermal sensor unit (TSU) that measures the
temperature inside the LSI.
The thermal sensor in this unit measures temperatures in the range from
−40 degree Celsius to 125 degree Celsius with an accuracy of ±3°C. The
TSU repeats measurement at 20 microseconds intervals and automatically
updates the results of measurement.
The TSU has no interrupts as well as no external pins.
This patch adds Thermal Sensor Unit(TSU) driver for RZ/G2L SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211130155757.17837-3-biju.das.jz@bp.renesas.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The only usage of powerclamp_cooling_ops is to pass its address to
thermal_cooling_device_register(), which takes a pointer to const struct
thermal_cooling_device_ops. Make it const to allow the compiler to put
it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211128214641.30953-1-rikard.falkeborn@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Starting with commit d92ed2c9d3 ("thermal: imx: Use driver's local
data to decide whether to run a measurement") this driver stared using
irq_enabled flag to make decision to power on/off the thermal
core. This triggered a regression, where after reaching critical
temperature, alarm IRQ handler set irq_enabled to false, disabled
thermal core and was not able read temperature and disable cooling
sequence.
In case the cooling device is "CPU/GPU freq", the system will run with
reduce performance until next reboot.
To solve this issue, we need to move all parts implementing hand made
runtime power management and let it handle actual runtime PM framework.
Fixes: d92ed2c9d3 ("thermal: imx: Use driver's local data to decide whether to run a measurement")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Petr Beneš <petr.benes@ysoft.com>
Link: https://lore.kernel.org/r/20211117103426.81813-1-o.rempel@pengutronix.de
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In preparation for FORTIFY_SOURCE performing compile-time and
run-time field bounds checking for memcpy(), avoid intentionally
writing across neighboring fields.
Use struct_group() in struct art around members weight, and
ac[0-9]_max, so they can be referenced together. This will allow
memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the
end of weight.
"pahole" shows no size nor member offset changes to struct art.
"objdump -d" shows no meaningful object code changes (i.e. only
source line number induced differences).
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Thermal pressure provides a new API, which allows to use CPU frequency
as an argument. That removes the need of local conversion to capacity.
Use this new function and remove old conversion code.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
32-bit processors cannot generally access 64-bit MMIO registers
atomically, and it is unknown in which order the two halves of
this registers would need to be read:
drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c: In function 'send_mbox_cmd':
drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c:79:37: error: implicit declaration of function 'readq'; did you mean 'readl'? [-Werror=implicit-function-declaration]
79 | *cmd_resp = readq((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA));
| ^~~~~
| readl
The driver already does not build for anything other than x86,
so limit it further to x86-64.
Fixes: aeb58c860d ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit aeb58c860d ("thermal/drivers/int340x: processor_thermal: Suppot
64 bit RFIM responses") started using 'readq()' to read 64-bit status
responses from the int340x hardware.
That's all fine and good, but on 32-bit targets a 64-bit 'readq()' is
ambiguous, since it's no longer an atomic access. Some hardware might
require 64-bit accesses, and other hardware might want low word first or
high word first.
It's quite likely that the driver isn't relevant in a 32-bit environment
any more, and there's a patch floating around to just make it depend on
X86_64, but let's make it buildable on x86-32 anyway.
The driver previously just read the low 32 bits, so the hardware
certainly is ok with 32-bit reads, and in a little-endian environment
the low word first model is the natural one.
So just add the include for the 'io-64-nonatomic-lo-hi.h' version.
Fixes: aeb58c860d ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use pr_warn_once() instead of pr_warn() to print the user space
governor deprecation message in user_space_bind() to reduce the
kernel log noise.
Fixes: 0275c9fb0e ("thermal/core: Make the userspace governor deprecated")
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
of_parse_thermal_zones() parses the thermal-zones node and registers a
thermal_zone device for each subnode. However, if a thermal zone is
consuming a thermal sensor and that thermal sensor device hasn't probed
yet, an attempt to set trip_point_*_temp for that thermal zone device
can cause a NULL pointer dereference. Fix it.
console:/sys/class/thermal/thermal_zone87 # echo 120000 > trip_point_0_temp
...
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
Call trace:
of_thermal_set_trip_temp+0x40/0xc4
trip_point_temp_store+0xc0/0x1dc
dev_attr_store+0x38/0x88
sysfs_kf_write+0x64/0xc0
kernfs_fop_write_iter+0x108/0x1d0
vfs_write+0x2f4/0x368
ksys_write+0x7c/0xec
__arm64_sys_write+0x20/0x30
el0_svc_common.llvm.7279915941325364641+0xbc/0x1bc
do_el0_svc+0x28/0xa0
el0_svc+0x14/0x24
el0_sync_handler+0x88/0xec
el0_sync+0x1c0/0x200
While at it, fix the possible NULL pointer dereference in other
functions as well: of_thermal_get_temp(), of_thermal_set_emul_temp(),
of_thermal_get_trend().
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Subbaraman Narayanamurthy <quic_subbaram@quicinc.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some of the RFIM mail box command returns 64 bit values. So enhance
mailbox interface to return 64 bit values and use them for RFIM
commands.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 5d6fbc96bd ("thermal/drivers/int340x: processor_thermal: Export additional attributes")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cooling devices have their cooling device set_cur_state
read-writable all the time in the sysfs directory, thus allowing the
userspace to act on it.
The thermal framework is wrongly used by userspace as a power capping
framework by acting on the cooling device opaque state. This one then
competes with the in-kernel governor decision.
We have seen in out-of-tree kernels, a big number of devices which are
abusely declaring themselves as cooling device just to act on their
power.
The role of the thermal framework is to protect the junction
temperature of the silicon. Letting the userspace to play with a
cooling device is invalid and potentially dangerous.
The powercap framework is the right framework to do power capping and
moreover it deals with the aggregation via the dev pm qos.
As the userspace governor is marked deprecated and about to be
removed, there is no point to keep this file writable also in the
future.
Emit a warning and deprecate the interface.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20211019163506.2831454-2-daniel.lezcano@linaro.org
The userspace governor is sending temperature when polling is active
and trip point crossed events. Nothing else.
AFAICT, this governor is used with custom kernels making the userspace
governor co-existing with another governor on the same thermal zone
because there was no notification mechanism, implying a hack in the
framework to support this configuration.
The new netlink thermal notification is able to provide more
information than the userspace governor and give the opportunity to
the users of this governor to replace it by a dedicated notification
framework.
The userspace governor will be removed as its usage is no longer
needed.
Add a warning message to tell the userspace governor is deprecated.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20211019163506.2831454-1-daniel.lezcano@linaro.org
When the driver resumes, the tcc offset is set back to its previous
value. But this only works if the value was user defined as otherwise
the offset isn't saved. This asymmetric logic is harder to maintain and
introduced some issues.
Improve the logic by saving the tcc offset in a suspend op, so the right
value is always restored after a resume.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-3-atenart@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The tsadc node in rk356x.dtsi has more resets then currently supported
by the rockchip_thermal.c driver, so use
devm_reset_control_array_get() to reset them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210930110517.14323-3-jbx6244@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The function can loop and lock the system if for whatever reason the bit
for the target sensor is NEVER valid. This is the case if a sensor is
disabled by the factory and the valid bit is never reported as actually
valid. Add a timeout check and exit if a timeout occurs. As this is
a very rare condition, handle the timeout only if the first read fails.
While at it also rework the function to improve readability and convert
to poll_timeout generic macro.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211007172859.583-1-ansuelsmth@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When device_register() return failed, program will goto out_kfree_type
to release 'cdev->device' by put_device(). That will call thermal_release()
to free 'cdev'. But the follow-up processes access 'cdev' continually.
That trggers the UAF bug.
====================================================================
BUG: KASAN: use-after-free in __thermal_cooling_device_register+0x75b/0xa90
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? __thermal_cooling_device_register+0x75b/0xa90
kasan_report.cold+0x7f/0x11b
? __thermal_cooling_device_register+0x75b/0xa90
__thermal_cooling_device_register+0x75b/0xa90
? memset+0x20/0x40
? __sanitizer_cov_trace_pc+0x1d/0x50
? __devres_alloc_node+0x130/0x180
devm_thermal_of_cooling_device_register+0x67/0xf0
max6650_probe.cold+0x557/0x6aa
......
Freed by task 258:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
thermal_release+0xa0/0x110
device_release+0xa7/0x240
kobject_put+0x1ce/0x540
put_device+0x20/0x30
__thermal_cooling_device_register+0x731/0xa90
devm_thermal_of_cooling_device_register+0x67/0xf0
max6650_probe.cold+0x557/0x6aa [max6650]
Do not use 'cdev' again after put_device() to fix the problem like doing
in thermal_zone_device_register().
[dlezcano]: as requested by Rafael, change the affectation into two statements.
Fixes: 5848376181 ("thermal/drivers/core: Use a char pointer for the cooling device name")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211015024504.947520-1-william.xuanziyang@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
If both dev_set_name() and device_register() failed, then null pointer
dereference occurs in thermal_release() which will use strncmp() to
compare the name.
So fix it by adding dev_set_name() return value check.
Signed-off-by: Yuanzheng Song <songyuanzheng@huawei.com>
Link: https://lore.kernel.org/r/20211015083230.67658-1-songyuanzheng@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In production hardware the calibration values used to convert register
values to temperatures can be read from hardware. While pre-production
hardware still depends on pseudo values hard-coded in the driver.
Add support for reading out calibration values from hardware if it's
fused. The presence of fused calibration is indicated in the THSCP
register.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211014103816.1939782-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Prepare for reading the THCODE and PTAT values from hardware fuses by
storing the values used during calculations in the drivers private
data structures.
As the values are now stored directly in the private data structures
there is no need to keep track of the TSC channel id as its only usage
was to lookup the THCODE row, drop it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211014103816.1939782-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The variant of the ADC Thermal Monitor block found in e.g. PM8998 is
"HC", add support for this variant to the ADC TM5 driver in order to
support using VADC channels as thermal_zones on SDM845 et al.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211005032531.2251928-3-bjorn.andersson@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The slope of the temperature increase or decrease can be high and when
the temperature crosses the trip point, there could be a significant
difference between the trip temperature and the measured temperatures.
That forces the userspace to read the temperature back right after
receiving a trip violation notification.
In order to be efficient, give the temperature which resulted in the
trip violation.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20211001223323.1836640-1-daniel.lezcano@linaro.org
The only usage of thermal_mmio_ops is to pass its address to
devm_thermal_zone_of_sensor_register(), which has a pointer to const
struct thermal_zone_of_device_ops as argument. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210920203849.32136-1-rikard.falkeborn@gmail.com
This check has a signedness bug and does not work. If "length" is
larger than "PAGE_SIZE" then "PAGE_SIZE - length" is not negative
but instead it is a large unsigned value. Fortunately, Takashi Iwai
changed this code to use scnprint() instead of snprintf() so now
"length" is never larger than "PAGE_SIZE - 1" and the check can be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'cpu_clamping_mask' is a bitmap. So use 'bitmap_zalloc()' and
'bitmap_free()' to simplify code, improve the semantic of the code and
avoid some open-coded arithmetic in allocator arguments.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices can have some thermal sensors disabled from the
factory. The current two irq handler functions check all the sensor by
default and the check if the sensor was actually registered is
wrong. The tzd is actually never set if the registration fails hence
the IS_ERR check is wrong.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210907212543.20220-1-ansuelsmth@gmail.com
After printing the list of thermal governors, then this function prints
a newline character. The problem is that "size" has not been updated
after printing the last governor. This means that it can write one
character (the NUL terminator) beyond the end of the buffer.
Get rid of the "size" variable and just use "PAGE_SIZE - count" directly.
Fixes: 1b4f48494e ("thermal: core: group functions related to governor handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210916131342.GB25094@kili
After upgrading to Linux 5.13.3 I noticed my laptop would shutdown due
to overheat (when it should not). It turned out this was due to commit
fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting").
What happens is this drivers uses a global variable to keep track of the
tcc offset (tcc_offset_save) and uses it on resume. The issue is this
variable is initialized to 0, but is only set in
tcc_offset_degree_celsius_store, i.e. when the tcc offset is explicitly
set by userspace. If that does not happen, the resume path will set the
offset to 0 (in my case the h/w default being 3, the offset would become
too low after a suspend/resume cycle).
The issue did not arise before commit fe6a6de669, as the function
setting the offset would return if the offset was 0. This is no longer
the case (rightfully).
Fix this by not applying the offset if it wasn't saved before, reverting
back to the old logic. A better approach will come later, but this will
be easier to apply to stable kernels.
The logic to restore the offset after a resume was there long before
commit fe6a6de669, but as a value of 0 was considered invalid I'm
referencing the commit that made the issue possible in the Fixes tag
instead.
Fixes: fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting")
Cc: stable@vger.kernel.org
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-2-atenart@kernel.org
tegra by adding a dependency on ARCH_TEGRA along with COMPILE_TEST
(Dmitry Osipenko)
- Fix the error code for the exynos when devm_get_clk() fails (Dan
Carpenter)
- Add the TCC cooling support for AlderLake platform (Sumeet Pawnikar)
- Add support for hardware trip points for the rcar gen3 thermal
driver and store TSC id as unsigned int (Niklas Söderlund)
- Replace the deprecated CPU-hotplug functions get_online_cpus() and
put_online_cpus (Sebastian Andrzej Siewior)
- Add the thermal tools directory in the MAINTAINERS file (Daniel
Lezcano)
- Fix the Makefile and the cross compilation flags for the userspace
'tmon' tool (Rolf Eike Beer)
- Allow to use the IMOK independently from the GDDV on Int340x (Sumeet
Pawnikar)
- Fix the stub thermal_cooling_device_register() function prototype
which does not match the real function (Arnd Bergmann)
- Make the thermal trip point optional in the DT bindings (Maxime
Ripard)
- Fix a typo in a comment in the core code (Geert Uytterhoeven)
- Reduce the verbosity of the trace in the SoC thermal tegra driver
(Dmitry Osipenko)
- Add the support for the LMh (Limit Management hardware) driver on
the QCom platforms (Thara Gopinath)
- Allow processing of HWP interrupt by adding a weak function in the
Intel driver (Srinivas Pandruvada)
- Prevent an abort of the sensor probe is a channel is not used
(Matthias Kaehlcke)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmE7yAcACgkQqDIjiipP
6E8WKwgAmI+kdOURCz1CtCIv6FnQFx20suxZidfATPULBPZ8zcHqdjxJECXJpvDz
y8T8dGAPRqXmMBJm2vF/qVraHaDJvscHXaflhsurhyEp0tiGptNeugBosso0jDEQ
JFrQ6Rny/NCmNMOkWW4YlSfkik0zQ43xlHocy3UfOKfcshhYWGsPTbIXdA6wH/zh
3tFW8j327tkyenrKZiaioJOSX88Oyy7Ft8l5k0HP+hPYkrvihWDJuEfEEmpfkdA7
Q70Lacf2QtFP8mUfGKpQxURSgndjphDPU7tzP5NqqWvLuT94aTspvJx4ywVwK8Iv
o+jNvR33yBIs5FXXB7B1ymkNE1h8uQ==
=blIQ
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add the tegra3 thermal sensor and fix the compilation testing on
tegra by adding a dependency on ARCH_TEGRA along with COMPILE_TEST
(Dmitry Osipenko)
- Fix the error code for the exynos when devm_get_clk() fails (Dan
Carpenter)
- Add the TCC cooling support for AlderLake platform (Sumeet Pawnikar)
- Add support for hardware trip points for the rcar gen3 thermal driver
and store TSC id as unsigned int (Niklas Söderlund)
- Replace the deprecated CPU-hotplug functions get_online_cpus() and
put_online_cpus (Sebastian Andrzej Siewior)
- Add the thermal tools directory in the MAINTAINERS file (Daniel
Lezcano)
- Fix the Makefile and the cross compilation flags for the userspace
'tmon' tool (Rolf Eike Beer)
- Allow to use the IMOK independently from the GDDV on Int340x (Sumeet
Pawnikar)
- Fix the stub thermal_cooling_device_register() function prototype
which does not match the real function (Arnd Bergmann)
- Make the thermal trip point optional in the DT bindings (Maxime
Ripard)
- Fix a typo in a comment in the core code (Geert Uytterhoeven)
- Reduce the verbosity of the trace in the SoC thermal tegra driver
(Dmitry Osipenko)
- Add the support for the LMh (Limit Management hardware) driver on the
QCom platforms (Thara Gopinath)
- Allow processing of HWP interrupt by adding a weak function in the
Intel driver (Srinivas Pandruvada)
- Prevent an abort of the sensor probe is a channel is not used
(Matthias Kaehlcke)
* tag 'thermal-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal/drivers/qcom/spmi-adc-tm5: Don't abort probing if a sensor is not used
thermal/drivers/intel: Allow processing of HWP interrupt
dt-bindings: thermal: Add dt binding for QCOM LMh
thermal/drivers/qcom: Add support for LMh driver
firmware: qcom_scm: Introduce SCM calls to access LMh
thermal/drivers/tegra-soctherm: Silence message about clamped temperature
thermal: Spelling s/scallbacks/callbacks/
dt-bindings: thermal: Make trips node optional
thermal/core: Fix thermal_cooling_device_register() prototype
thermal/drivers/int340x: Use IMOK independently
tools/thermal/tmon: Add cross compiling support
thermal/tools/tmon: Improve the Makefile
MAINTAINERS: Add missing userspace thermal tools to the thermal section
thermal/drivers/intel_powerclamp: Replace deprecated CPU-hotplug functions.
thermal/drivers/rcar_gen3_thermal: Store TSC id as unsigned int
thermal/drivers/rcar_gen3_thermal: Add support for hardware trip points
drivers/thermal/intel: Add TCC cooling support for AlderLake platform
thermal/drivers/exynos: Fix an error code in exynos_tmu_probe()
thermal/drivers/tegra: Correct compile-testing of drivers
thermal/drivers/tegra: Add driver for Tegra30 thermal sensor
adc_tm5_register_tzd() registers the thermal zone sensors for all
channels of the thermal monitor. If the registration of one channel
fails the function skips the processing of the remaining channels
and returns an error, which results in _probe() being aborted.
One of the reasons the registration could fail is that none of the
thermal zones is using the channel/sensor, which hardly is a critical
error (if it is an error at all). If this case is detected emit a
warning and continue with processing the remaining channels.
Fixes: ca66dca5ed ("thermal: qcom: add support for adc-tm5 PMIC thermal monitor")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reported-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210823134726.1.I1dd23ddf77e5b3568625d80d6827653af071ce19@changeid
Add a weak function to process HWP (Hardware P-states) notifications and
move updating HWP_STATUS MSR to this function.
This allows HWP interrupts to be processed by the intel_pstate driver in
HWP mode by overriding the implementation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210820024006.2347720-1-srinivas.pandruvada@linux.intel.com
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
The new macro uses a unsigned long type which is already the type in the
current code via the 'freq' variable.
Link: https://lkml.kernel.org/r/20210816114732.1834145-4-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights:
- Move all the Intel drivers into their own subdir(s) (mostly Kate's work)
- New meraki-mx100 platform driver
- Asus WMI driver enhancements, including
/sys/firmware/acpi/platform_profile support
- New BIOS SAR driver for Intel M.2 WWAM modems
- Alder Lake support for the Intel PMC driver
- A whole bunch of cleanups + fixes all over the place
The following is an automated git shortlog grouped by driver:
BIOS SAR driver for Intel M.2 Modem:
- BIOS SAR driver for Intel M.2 Modem
ISST:
- use semi-colons instead of commas
- Fix optimization with use of numa
Replace deprecated CPU-hotplug functions.:
- Replace deprecated CPU-hotplug functions.
Update Mario Limonciello's email address in the docs:
- Update Mario Limonciello's email address in the docs
acer-wmi:
- Add Turbo Mode support for Acer PH315-53
add meraki-mx100 platform driver:
- add meraki-mx100 platform driver
asus-nb-wmi:
- Add tablet_mode_sw=lid-flip quirk for the TP200s
- Allow configuring SW_TABLET_MODE method with a module option
asus-wmi:
- Fix "unsigned 'retval' is never less than zero" smatch warning
- Delete impossible condition
- Add support for platform_profile
- Add egpu enable method
- Add dgpu disable method
- Add panel overdrive functionality
dell-smbios:
- Remove unused dmi_system_id table
dell-smbios-wmi:
- Add missing kfree in error-exit from run_smbios_call
- Avoid false-positive memcpy() warning
dell-smo8800:
- Convert to be a platform driver
dual_accel_detect:
- Use the new i2c_acpi_client_count() helper
gigabyte-wmi:
- add support for B450M S2H V2
- add support for X570 GAMING X
hp_accel:
- Convert to be a platform driver
- Remove _INI method call
i2c:
- acpi: Add an i2c_acpi_client_count() helper function
i2c-multi-instantiate:
- Use the new i2c_acpi_client_count() helper
ideapad-laptop:
- Fix Legion 5 Fn lock LED
intel-hid:
- Move to intel sub-directory
intel-rst:
- Move to intel sub-directory
intel-smartconnect:
- Move to intel sub-directory
intel-uncore-frequency:
- Move to intel sub-directory
intel-vbtn:
- Move to intel sub-directory
intel-wmi-sbl-fw-update:
- Move to intel sub-directory
intel-wmi-thunderbolt:
- Move to intel sub-directory
intel_atomisp2:
- Move to intel sub-directory
intel_bxtwc_tmu:
- Move to intel sub-directory
intel_cht_int33fe:
- Use the new i2c_acpi_client_count() helper
intel_chtdc_ti_pwrbtn:
- Move to intel sub-directory
intel_int0002_vgpio:
- Move to intel sub-directory
intel_mrfld_pwrbtn:
- Move to intel sub-directory
intel_oaktrail:
- Move to intel sub-directory
intel_pmc_core:
- Move to intel sub-directory
- Prevent possibile overflow
intel_pmt_telemetry:
- Ignore zero sized entries
intel_punit_ipc:
- Move to intel sub-directory
intel_scu_ipc:
- Fix doc of intel_scu_ipc_dev_command_with_size()
intel_speed_select_if:
- Move to intel sub-directory
intel_telemetry:
- Move to intel sub-directory
intel_turbo_max_3:
- Move to intel sub-directory
lg-laptop:
- Use correct event for keyboard backlight FN-key
- Use correct event for touchpad toggle FN-key
- Support for battery charge limit on newer models
platform/mellanox:
- mlxbf-pmc: fix kernel-doc notation
platform/surface:
- aggregator: Use y instead of objs in Makefile
- surface3_power: Use i2c_acpi_get_i2c_resource() helper
platform/x86/intel:
- pmc/core: Add GBE Package C10 fix for Alder Lake PCH
- pmc/core: Add Alder Lake low power mode support for pmc core
- pmc/core: Add Latency Tolerance Reporting (LTR) support to Alder Lake
- pmc/core: Add Alderlake support to pmc core driver
- int3472: Use y instead of objs in Makefile
- pmt: Use y instead of objs in Makefile
- int33fe: Use y instead of objs in Makefile
- Move Intel PMT drivers to new subfolder
thermal/drivers/intel:
- Move intel_menlow to thermal drivers
think-lmi:
- add debug_cmd
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmEw1KAUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wk7Qf/dsaaDgx7aC6DfKzdcMgfeLIdTaGm
a6svNXM2t/JFdvhjYzxA+4QlQgco7zkN06iRlWbObEonSUsHlGlwEOHX60VgcopO
qJaqnznmfdXUocFTnA+5acJXabNaw7xkKHS0K61UWgk+mm6aMuygpKxULnNTa4X+
p3HoU6uXFckpoA/Jstzo5UfegNYhg11bflNd7XN4F3rMCbbNHAsWlf4oVr2YsEHa
wECW+1e8wZl4BInUzoXQhilRoybJWXWJ8sLsvQfDXLs9aNoLdDqu9p0MuXEW5QqE
wNt26SNNAP2L49BD6kaJszV5Ry/jNSEtVkWwkrzHbGTZoOEyMYas8pm6Uw==
=iK1W
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- Move all the Intel drivers into their own subdir(s) (mostly Kate's
work)
- New meraki-mx100 platform driver
- Asus WMI driver enhancements, including support for
/sys/firmware/acpi/platform_profile
- New BIOS SAR driver for Intel M.2 WWAM modems
- Alder Lake support for the Intel PMC driver
- A whole bunch of cleanups + fixes all over the place"
* tag 'platform-drivers-x86-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
platform/x86: dell-smbios-wmi: Add missing kfree in error-exit from run_smbios_call
platform/x86: dell-smbios-wmi: Avoid false-positive memcpy() warning
platform/x86: ISST: use semi-colons instead of commas
platform/x86: asus-wmi: Fix "unsigned 'retval' is never less than zero" smatch warning
platform/x86: asus-wmi: Delete impossible condition
platform/x86: hp_accel: Convert to be a platform driver
platform/x86: hp_accel: Remove _INI method call
platform/mellanox: mlxbf-pmc: fix kernel-doc notation
platform/x86/intel: pmc/core: Add GBE Package C10 fix for Alder Lake PCH
platform/x86/intel: pmc/core: Add Alder Lake low power mode support for pmc core
platform/x86/intel: pmc/core: Add Latency Tolerance Reporting (LTR) support to Alder Lake
platform/x86/intel: pmc/core: Add Alderlake support to pmc core driver
platform/x86: intel-wmi-thunderbolt: Move to intel sub-directory
platform/x86: intel-wmi-sbl-fw-update: Move to intel sub-directory
platform/x86: intel-vbtn: Move to intel sub-directory
platform/x86: intel_oaktrail: Move to intel sub-directory
platform/x86: intel_int0002_vgpio: Move to intel sub-directory
platform/x86: intel-hid: Move to intel sub-directory
platform/x86: intel_atomisp2: Move to intel sub-directory
platform/x86: intel_speed_select_if: Move to intel sub-directory
...
Add a weak function to process HWP (Hardware P-states) notifications and
move updating HWP_STATUS MSR to this function.
This allows HWP interrupts to be processed by the intel_pstate driver in
HWP mode by overriding the implementation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Driver enabling various pieces of Limits Management Hardware(LMh) for cpu
cluster0 and cpu cluster1 namely kick starting monitoring of temperature,
current, battery current violations, enabling reliability algorithm and
setting up various temperature limits.
The following has been explained in the cover letter. I am including this
here so that this remains in the commit message as well.
LMh is a hardware infrastructure on some Qualcomm SoCs that can enforce
temperature and current limits as programmed by software for certain IPs
like CPU. On many newer LMh is configured by firmware/TZ and no programming
is needed from the kernel side. But on certain SoCs like sdm845 the
firmware does not do a complete programming of the h/w. On such soc's
kernel software has to explicitly set up the temperature limits and turn on
various monitoring and enforcing algorithms on the hardware.
Tested-by: Steev Klimaszewski <steev@kali.org> # Lenovo Yoga C630
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210809191605.3742979-3-thara.gopinath@linaro.org
Moved drivers/platform/x86/intel_menlow.c to drivers/thermal/intel.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20210816035356.1955982-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Tegra soctherm driver prints message about the clamped temperature
trip each time when thermal core disables the low/high trip. The message
is confusing and creates illusion that driver is malfunctioning. Turn that
noisy info message into a debug message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210712002353.17276-1-digetx@gmail.com
Some chrome platform requires IMOK method in coreboot. But these platforms
don't use GDDV data vault in coreboot. As per current code flow, to enable
and use IMOK only, we need to have GDDV support as well in coreboot. This
patch removes the dependency for IMOK from GDDV to enable and use IMOK
independently.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210716163946.3142-1-sumeet.r.pawnikar@intel.com
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210803141621.780504-20-bigeasy@linutronix.de
The TSC id and number of TSC ids should be stored as unsigned int as
they can't be negative. Fix the datatype of the loop counter 'i' and
rcar_gen3_thermal_tsc.id to reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210804091818.2196806-3-niklas.soderlund+renesas@ragnatech.se
All supported hardware except V3U is capable of generating interrupts
to the CPU when the temperature go below or above a set value. Use this
to implement support for the set_trip() feature of the thermal core on
supported hardware.
The V3U have its interrupts routed to the ECM module and therefore can
not be used to implement set_trip() as the driver can't be made aware of
when the interrupt triggers.
Each TSC is capable of tracking up-to three different temperatures while
only two are needed to implement the tracking of the thermal window.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210804091818.2196806-2-niklas.soderlund+renesas@ragnatech.se
This error path return success but it should propagate the negative
error code from devm_clk_get().
Fixes: 6c247393cf ("thermal: exynos: Add TMU support for Exynos7 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210810084413.GA23810@kili
All Tegra thermal drivers support compile-testing, but the drivers are
not available for compile-testing because the whole Kconfig meny entry
depends on ARCH_TEGRA, missing the alternative COMPILE_TEST dependency
option. Correct the Kconfig entry.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210617072403.3487-1-digetx@gmail.com
All NVIDIA Tegra30 SoCs have a two-channel on-chip sensor unit which
monitors temperature and voltage of the SoC. Sensors control CPU frequency
throttling, which is activated by hardware once preprogrammed temperature
level is breached, they also send signal to Power Management controller to
perform emergency shutdown on a critical overheat of the SoC die. Add
driver for the Tegra30 TSENSOR module, exposing it as a thermal sensor.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201T
Tested-by: Ihor Didenko <tailormoon@rambler.ru> # Asus TF300T
Tested-by: Ion Agorria <ion@agorria.com> # Asus TF201T
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210616190417.32214-4-digetx@gmail.com
- Add missing MODULE_DEVICE_TABLE for the Spreadtrum sensor (Chunyan
Zhang)
- Export additionnal attributes for the int340x thermal processor
(Srinivas Pandruvada)
- Add SC7280 compatible for the tsens driver (Rajeshwari Ravindra
Kamble)
- Fix kernel documentation for thermal_zone_device_unregister() and
use devm_platform_get_and_ioremap_resource() (Yang Yingliang)
- Fix coefficient calculations for the rcar_gen3 sensor driver (Niklas
Söderlund)
- Fix shadowing variable rcar_gen3_ths_tj_1 (Geert Uytterhoeven)
- Add missing of_node_put() for the iMX and Spreadtrum sensors
(Krzysztof Kozlowski)
- Add tegra3 thermal sensor DT bindings (Dmitry Osipenko)
- Stop the thermal zone monitoring when unregistering it to prevent a
temperature update without the 'get_temp' callback (Dmitry Osipenko)
- Add rk3568 DT bindings, convert bindings to yaml schemas and add the
corresponding compatible in the Rockchip sensor (Ezequiel Garcia)
- Add the sc8180x compatible for the Qualcomm tsensor (Bjorn Andersson)
- Use the find_first_zero_bit() function instead of custom code (Andy
Shevchenko)
- Fix the kernel doc for the device cooling device (Yang Li)
- Reorg the processor thermal int340x to set the scene for the PCI
mmio driver (Srinivas Pandruvada)
- Add PCI MMIO driver for the int340x processor thermal driver
(Srinivas Pandruvada)
- Add hwmon sensors for the mediatek sensor (Frank Wunderlich)
- Fix warning for return value reported by Smatch for the int340x
thermal processor (Srinivas Pandruvada)
- Fix wrong register access and decoding for the int340x thermal
processor (Srinivas Pandruvada)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmDkbdAACgkQqDIjiipP
6E8pTwgAgc4RMdSBdNMVWP1Lc3Gprmg8uXMhma9ZlmJD+l3h4b4P+Zm7HjU+SPHI
emvvqHgiWGw/ta/Fuhx9XnqTUjZznG3gMYohnfKe7jPgVTxmud+Yf0/E3dRrDNWl
WNolS8rv4dLf1mjR+vGZ63KasK0Rz5Z4YxDV4kOvh+/VUhqg3XpZ1OTKOh/B9IWX
pUTedq7hIZ44ZMINcwObvLNTeaoEhPNpgA4Rs07vQPYugY0V61HszqR/Mu+l8Rgp
LiE8NUBANJ+8+wydHe/vP6lvOthh7YGSx4091rUe+X17qgfBDKCTsOyECnZ/UX+r
aB1MaTAnr1H0dfM49yeoFcMSPc1rGA==
=q0nG
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add rk3568 sensor support (Finley Xiao)
- Add missing MODULE_DEVICE_TABLE for the Spreadtrum sensor (Chunyan
Zhang)
- Export additionnal attributes for the int340x thermal processor
(Srinivas Pandruvada)
- Add SC7280 compatible for the tsens driver (Rajeshwari Ravindra
Kamble)
- Fix kernel documentation for thermal_zone_device_unregister() and use
devm_platform_get_and_ioremap_resource() (Yang Yingliang)
- Fix coefficient calculations for the rcar_gen3 sensor driver (Niklas
Söderlund)
- Fix shadowing variable rcar_gen3_ths_tj_1 (Geert Uytterhoeven)
- Add missing of_node_put() for the iMX and Spreadtrum sensors
(Krzysztof Kozlowski)
- Add tegra3 thermal sensor DT bindings (Dmitry Osipenko)
- Stop the thermal zone monitoring when unregistering it to prevent a
temperature update without the 'get_temp' callback (Dmitry Osipenko)
- Add rk3568 DT bindings, convert bindings to yaml schemas and add the
corresponding compatible in the Rockchip sensor (Ezequiel Garcia)
- Add the sc8180x compatible for the Qualcomm tsensor (Bjorn Andersson)
- Use the find_first_zero_bit() function instead of custom code (Andy
Shevchenko)
- Fix the kernel doc for the device cooling device (Yang Li)
- Reorg the processor thermal int340x to set the scene for the PCI mmio
driver (Srinivas Pandruvada)
- Add PCI MMIO driver for the int340x processor thermal driver
(Srinivas Pandruvada)
- Add hwmon sensors for the mediatek sensor (Frank Wunderlich)
- Fix warning for return value reported by Smatch for the int340x
thermal processor (Srinivas Pandruvada)
- Fix wrong register access and decoding for the int340x thermal
processor (Srinivas Pandruvada)
* tag 'thermal-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (23 commits)
thermal/drivers/int340x/processor_thermal: Fix tcc setting
thermal/drivers/int340x/processor_thermal: Fix warning for return value
thermal/drivers/mediatek: Add sensors-support
thermal/drivers/int340x/processor_thermal: Add PCI MMIO based thermal driver
thermal/drivers/int340x/processor_thermal: Split enumeration and processing part
thermal: devfreq_cooling: Fix kernel-doc
thermal/drivers/intel/intel_soc_dts_iosf: Switch to use find_first_zero_bit()
dt-bindings: thermal: tsens: Add sc8180x compatible
dt-bindings: rockchip-thermal: Support the RK3568 SoC compatible
dt-bindings: thermal: convert rockchip-thermal to json-schema
thermal/core/thermal_of: Stop zone device before unregistering it
dt-bindings: thermal: Add binding for Tegra30 thermal sensor
thermal/drivers/sprd: Add missing of_node_put for loop iteration
thermal/drivers/imx_sc: Add missing of_node_put for loop iteration
thermal/drivers/rcar_gen3_thermal: Do not shadow rcar_gen3_ths_tj_1
thermal/drivers/rcar_gen3_thermal: Fix coefficient calculations
thermal/drivers/st: Use devm_platform_get_and_ioremap_resource()
thermal/core: Correct function name thermal_zone_device_unregister()
dt-bindings: thermal: tsens: Add compatible string to TSENS binding for SC7280
thermal/drivers/int340x: processor_thermal: Export additional attributes
...
The following fixes are done for tcc sysfs interface:
- TCC is 6 bits only from bit 29-24
- TCC of 0 is valid
- When BIT(31) is set, this register is read only
- Check for invalid tcc value
- Error for negative values
Fixes: fdf4f2fb8e ("drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210628215803.75038-1-srinivas.pandruvada@linux.intel.com
