IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Intel-SoC enhancements (Andy Shevchenko)
- Intel CPU symbolic model definition rework (Dave Hansen)
- ... other misc changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/sfi: Enable enumeration of SD devices
x86/pci: Use MRFLD abbreviation for Merrifield
x86/platform/intel-mid: Make vertical indentation consistent
x86/platform/intel-mid: Mark regulators explicitly defined
x86/platform/intel-mid: Rename mrfl.c to mrfld.c
x86/platform/intel-mid: Enable spidev on Intel Edison boards
x86/platform/intel-mid: Extend PWRMU to support Penwell
x86/pci, x86/platform/intel_mid_pci: Remove duplicate power off code
x86/platform/intel-mid: Add pinctrl for Intel Merrifield
x86/platform/intel-mid: Enable GPIO expanders on Edison
x86/platform/intel-mid: Add Power Management Unit driver
x86/platform/atom/punit: Enable support for Merrifield
x86/platform/intel_mid_pci: Rework IRQ0 workaround
x86, thermal: Clean up and fix CPU model detection for intel_soc_dts_thermal
x86, mmc: Use Intel family name macros for mmc driver
x86/intel_telemetry: Use Intel family name macros for telemetry driver
x86/acpi/lss: Use Intel family name macros for the acpi_lpss driver
x86/cpufreq: Use Intel family name macros for the intel_pstate cpufreq driver
x86/platform: Use new Intel model number macros
x86/intel_idle: Use Intel family macros for intel_idle
...
Pull libnvdimm fix from Dan Williams:
"This contains a regression fix for a problem that was introduced in
v4.7-rc6.
In 4.7-rc1 we introduced auto-probing for the ACPI DSM (device-
specific-method) format that the platform firmware implements for
nvdimm devices. We initially fixed a regression in probing the QEMU
DSM implementation by making acpi_check_dsm() tolerant of the way QEMU
reports the "0 DSMs supported" condition.
However, that broke HPE platforms since that tolerance caused the
driver to mistakenly match the 1-zero-byte response those platforms
give to "unknown" commands. Instead, we simply make the driver
tolerant of not finding any supported DSMs. This has been tested to
work with both QEMU and HPE platforms.
This commit has appeared in a -next release with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: make DIMM DSMs optional
Commit 4995734e97 "acpi, nfit: fix acpi_check_dsm() vs zero functions
implemented" attempted to fix a QEMU regression by supporting its usage
of a zero-mask as a valid response to a DSM-family probe request.
However, this behavior breaks HP platforms that return a zero-mask by
default causing the probe to misidentify the DSM-family.
Instead, the QEMU regression can be fixed by simply not requiring the DSM
family to be identified.
This effectively reverts commit 4995734e97, and removes the DSM
requirement from the init path.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Fixes: 4995734e97 ("acpi, nfit: fix acpi_check_dsm() vs zero functions implemented")
Reported-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Revert commit 2f38b1b16d (ACPICA: Namespace: Fix deadlock triggered by
MLC support in dynamic table loading) that attempted to fix a deadlock
issue introduced by a previous commit, but it led to a lock ordering
inconsistency that caused further problems to appear.
Fixes: 2f38b1b16d (ACPICA: Namespace: Fix deadlock triggered by MLC support in dynamic table loading)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is an order issue in ec_remove_handlers() that acpi_ec_stop()
is called before removing the operation region handler. That is
incorrect, because the operation region handler removal triggers
_REG(DISCONNECT) which may result in new EC transactions to carry
out.
That existing issue has been triggered by the following commit:
Commit: dcf15cbded
Subject: ACPI / EC: Fix a boot EC regresion by restoring boot EC
which changed the driver to call ec_remove_handlers() after invoking
_REG(CONNECT), so the issue has become visible.
Fixes: dcf15cbded (ACPI / EC: Fix a boot EC regresion by restoring boot EC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=102421
Reported-and-tested-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Nicholas <nkudriavtsev@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The FIFO unlocking mechanism in acpi_dbg has been broken by the
following commit:
Commit: 287980e49f
Subject: remove lots of IS_ERR_VALUE abuses
It converted !IS_ERR_VALUE(ret) into !ret which was not entirely
correct. Fix the regression by taking ret > 0 into account too as
appropriate.
Fixes: 287980e49f (remove lots of IS_ERR_VALUE abuses)
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Simplifications, changelog & subject massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a lock order issue in acpi_load_tables(). The namespace lock
is held before holding the interpreter lock.
With ACPI_MUTEX_DEBUG enabled in the kernel, this is printed to the
log during boot:
[ 0.885699] ACPI Error: Invalid acquire order: Thread 405884224 owns [ACPI_MTX_Namespace], wants [ACPI_MTX_Interpreter] (20160422/utmutex-263)
[ 0.885881] ACPI Error: Could not acquire AML Interpreter mutex (20160422/exutils-95)
[ 0.893846] ACPI Error: Mutex [0x0] is not acquired, cannot release (20160422/utmutex-326)
[ 0.894019] ACPI Error: Could not release AML Interpreter mutex (20160422/exutils-133)
The issue has been introduced by the following commit:
Commit: 2f38b1b16d
ACPICA Commit: bfe03ffcde8ed56a7eae38ea0b188aeb12f9c52e
Subject: ACPICA: Namespace: Fix a regression that MLC support triggers
dead lock in dynamic table loading
Which fixed a deadlock issue for acpi_ns_load_table() in
acpi_ex_add_table() but didn't take care of the lock order in
acpi_ns_load_table() correctly.
Originally (before the above commit), ACPICA used the
namespace/interpreter locks in the following 2 key code
paths:
1. Table loading:
acpi_ns_load_table
L(Namespace)
acpi_ns_parse_table
acpi_ns_one_complete_parse
U(Namespace)
2. Object evaluation:
acpi_ns_evaluate
L(Interpreter)
acpi_ps_execute_method
U(Interpreter)
acpi_ns_load_table
L(Namespace)
U(Namespace)
acpi_ev_initialize_region
L(Namespace)
U(Namespace)
address_space.setup
L(Namespace)
U(Namespace)
address_space.handler
L(Namespace)
U(Namespace)
acpi_os_wait_semaphore
acpi_os_acquire_mutex
acpi_os_sleep
L(Interpreter)
U(Interpreter)
During runtime, while acpi_ns_evaluate is called, the lock order is
always Interpreter -> Namespace.
In turn, the problematic commit acquires the locks in the following
order:
3. Table loading:
acpi_ns_load_table
L(Namespace)
acpi_ns_parse_table
L(Interpreter)
acpi_ns_one_complete_parse
U(Interpreter)
U(Namespace)
To fix the lock order issue, move the interpreter lock to
acpi_ns_load_table() to ensure the lock order correctness:
4. Table loading:
acpi_ns_load_table
L(Interpreter)
L(Namespace)
acpi_ns_parse_table
acpi_ns_one_complete_parse
U(Namespace)
U(Interpreter)
However, this doesn't fix the current design issues related to the
namespace lock. For example, we can notice that in acpi_ns_evaluate(),
outside of acpi_ns_load_table(), the namespace objects may be created
by the named object creation control methods. And the creation of
the method-owned namespace objects are not locked by the namespace
lock. This patch doesn't try to fix such kind of existing issues.
Fixes: 2f38b1b16d (ACPICA: Namespace: Fix a regression that MLC support triggers dead lock in dynamic table loading)
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit 103544d869 (ACPI,PCI,IRQ: reduce resource requirements)
the penalty values are calculated on the fly rather than at boot time.
This works fine for PCI interrupts but not so well for ISA interrupts.
The information on whether or not an ISA interrupt is in use is not
available to the pci_link.c code directly. That information is
obtained from the outside via acpi_penalize_isa_irq(). [If its
"active" argument is true, then the IRQ is in use by ISA.]
Since the current code relies on PCI Link objects for determination
of penalties, we are factoring in the PCI penalty twice after
acpi_penalize_isa_irq() function is called.
To avoid that, limit the newly added functionality to just PCI
interrupts so that old behavior is still maintained.
Fixes: 103544d869 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The change introduced in commit 103544d869 (ACPI,PCI,IRQ: reduce
resource requirements) omitted the initially applied PCI_POSSIBLE
penalty when the IRQ is active.
Incorrect calculation of the penalty leads the ACPI code to assigning
a wrong interrupt number to a PCI INTx interrupt.
This would not be as bad as it sounds in theory. It would just cause
the interrupts to be shared and result in performance penalty.
However, some drivers (like the parallel port driver) don't like
interrupt sharing and in the above case they will causes all of
the PCI drivers wanting to share the interrupt to be unable to
request it.
The issue has not been caught in testing because the behavior is
platform-specific and depends on the peripherals ending up sharing
the IRQ and their drivers.
Before the above commit the code would add the PCI_POSSIBLE value
divided by the number of possible IRQ users to the IRQ penalty
during initialization.
Later in that code path, if the IRQ is chosen as the active IRQ or
if it is used by ISA; additional penalties are added.
Fixes: 103544d869 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix an expression in the ACPI PCI IRQ management code added by a
recent commit that overlooked missing parens in it, so the result
of the computation is incorrect in some cases (Sinan Kaya).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=r8BR
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix an expression in the ACPI PCI IRQ management code added by a
recent commit that overlooked missing parens in it, so the result of
the computation is incorrect in some cases (Sinan Kaya)"
* tag 'acpi-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI,PCI,IRQ: correct operator precedence
Pull libnvdimm fixes from Dan Williams:
"1/ Two regression fixes since v4.6: one for the byte order of a sysfs
attribute (bz121161) and another for QEMU 2.6's NVDIMM _DSM (ACPI
Device Specific Method) implementation that gets tripped up by new
auto-probing behavior in the NFIT driver.
2/ A fix tagged for -stable that stops the kernel from
clobbering/ignoring changes to the configuration of a 'pfn'
instance ("struct page" driver). For example changing the
alignment from 2M to 1G may silently revert to 2M if that value is
currently stored on media.
3/ A fix from Eric for an xfstests failure in dax. It is not
currently tagged for -stable since it requires an 8-exabyte file
system to trigger, and there appear to be no user visible side
effects"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix format interface code byte order
dax: fix offset overflow in dax_io
acpi, nfit: fix acpi_check_dsm() vs zero functions implemented
libnvdimm, pfn, dax: fix initialization vs autodetect for mode + alignment
The omitted parenthesis prevents the addition operation when
acpi_penalize_isa_irq function is called.
Fixes: 103544d869 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Per JEDEC Annex L Release 3 the SPD data is:
Bits 9~5 00 000 = Function Undefined
00 001 = Byte addressable energy backed
00 010 = Block addressed
00 011 = Byte addressable, no energy backed
All other codes reserved
Bits 4~0 0 0000 = Proprietary interface
0 0001 = Standard interface 1
All other codes reserved; see Definitions of Functions
...and per the ACPI 6.1 spec:
byte0: Bits 4~0 (0 or 1)
byte1: Bits 9~5 (1, 2, or 3)
...so a format interface code displayed as 0x301 should be stored in the
nfit as (0x1, 0x3), little-endian.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Robert Elliott <elliott@hpe.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121161
Fixes: 30ec5fd464 ("nfit: fix format interface code byte order per ACPI6.1")
Fixes: 5ad9a7fde0 ("acpi/nfit: Update nfit driver to comply with ACPI 6.1")
Reported-by: Kristin Jacque <kristin.jacque@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
QEMU 2.6 implements nascent support for nvdimm DSMs. Depending on
configuration it may only implement the function0 dsm to indicate that
no other DSMs are available. Commit 31eca76ba2 "nfit, libnvdimm:
limited/whitelisted dimm command marshaling mechanism" breaks QEMU, but
QEMU is spec compliant. Per the spec the way to indicate that no
functions are supported is:
If Function Index is zero, the return is a buffer containing one bit
for each function index, starting with zero. Bit 0 indicates whether
there is support for any functions other than function 0 for the
specified UUID and Revision ID. If set to zero, no functions are
supported (other than function zero) for the specified UUID and
Revision ID.
Update the nfit driver to determine the family (interface UUID) without
requiring the implementation to define any other functions, i.e.
short-circuit acpi_check_dsm() to succeed per the spec. The nfit driver
appears to be the only user passing funcs==0 to acpi_check_dsm(), so
this behavior change of the common routine should be limited to the
probing done by the nfit driver.
Cc: Len Brown <lenb@kernel.org>
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Fixes: 31eca76ba2 ("nfit, libnvdimm: limited/whitelisted dimm command marshaling mechanism")
Reported-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Tested-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The new module-level code (MLC) approach invokes MLC on the per-table
basis, but the dynamic loading support of this is incorrect because
of the lock order:
acpi_ns_evaluate
acpi_ex_enter_intperter
acpi_ns_load_table (triggered by Load opcode)
acpi_ns_exec_module_code_list
acpi_ex_enter_intperter
The regression is introduced by the following commit:
Commit: 2785ce8d0d
ACPICA Commit: 071eff738c59eda1792ac24b3b688b61691d7e7c
Subject: ACPICA: Add per-table execution of module-level code
This patch fixes this regression by unlocking the interpreter lock
before invoking MLC. However, the unlocking is done to the
acpi_ns_load_table(), in which the interpreter lock should be locked
by acpi_ns_parse_table() but it wasn't.
Fixes: 2785ce8d0d (ACPICA: Add per-table execution of module-level code)
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 4.5+ <stable@vger.kernel.org> # 4.5+
[ rjw : Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 66b1ed5aa8 "ACPICA: ACPI 2.0, Hardware: Add
access_width/bit_offset support for acpi_hw_write()" that is reported
to break suspend-to-RAM (ACPI S3) on one system.
The root cause of the failure is a wrong access width value for one of
the involved registers provided by the ACPI tables, but before commit
66b1ed5aa8 that value was not taken into account at all and things
worked.
Fixes: 66b1ed5aa8 "ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()"
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Another straightforward replacement of magic numbers.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jacob.jun.pan@intel.com
Cc: linux-acpi@vger.kernel.org
Link: http://lkml.kernel.org/r/20160603001946.264CE704@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
According to the Windows probing result, during the table loading, the EC
device described in the ECDT should be used. And the ECDT EC is also
effective during the period the namespace objects are initialized (we can
see a separate process executing _STA/_INI on Windows before executing
other device specific control methods, for example, EC._REG). During the
device enumration, the EC device described in the DSDT should be used. But
there are differences between Linux and Windows around the device probing
order. Thus in Linux, we should enable the DSDT EC as early as possible
before enumerating devices in order not to trigger issues related to the
device enumeration order differences.
This patch thus converts acpi_boot_ec_enable() into acpi_ec_dsdt_probe() to
fix the gap. This also fixes a user reported regression triggered after we
switched the "table loading"/"ECDT support" to be ACPI spec 2.0 compliant.
Fixes: 59f0aa9480 (ACPI 2.0 / ECDT: Remove early namespace reference from EC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=119261
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Roland Dreier reports that one of his systems cannot boot because of
the changes made by commit ac212b6980 (ACPI / processor: Use common
hotplug infrastructure).
The problematic part of it is the request_region() call in
acpi_processor_get_info() that used to run at module init time before
the above commit and now it runs much earlier. Unfortunately, the
region(s) reserved by it fall into a range the PCI subsystem attempts
to reserve for AHCI IO BARs. As a result, the PCI reservation fails
and AHCI doesn't work, while previously the PCI reservation would
be made before acpi_processor_get_info() and it would succeed.
That request_region() call, however, was overlooked by commit
ac212b6980, as it is not necessary for the enumeration of the
processors. It only is needed when the ACPI processor driver
actually attempts to handle them which doesn't happen before
loading the ACPI processor driver module. Therefore that call
should have been moved from acpi_processor_get_info() into that
module.
Address the problem by moving the request_region() call in question
out of acpi_processor_get_info() and use the observation that the
region reserved by it is only needed if the FADT-based CPU
throttling method is going to be used, which means that it should
be sufficient to invoke it from acpi_processor_get_throttling_fadt().
Fixes: ac212b6980 (ACPI / processor: Use common hotplug infrastructure)
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The address check in acpi_hw_get_access_bit_width() should be byte width
based, not bit width based. This patch fixes this mistake.
For those who want to review acpi_hw_access_bit_width(), here is the
concerns and the design details of the function:
It is supposed that the GAS Address field should be aligned to the byte
width indicated by the GAS AccessSize field. Similarly, for the old non
GAS register, it is supposed that its Address should be aligned to its
Length.
For the "AccessSize = 0 (meaning ANY)" case, we try to return the maximum
instruction width (64 for MMIO or 32 for PIO) or the user expected access
bit width (64 for acpi_read()/acpi_write() or 32 for acpi_hw_read()/
acpi_hw_write()) and it is supposed that the GAS Address field should
always be aligned to the maximum expected access bit width (otherwise it
can't be accessed using ANY access bit width).
The problem is in acpi_tb_init_generic_address(), where the non GAS
register's Length is converted into the GAS BitWidth field, its Address is
converted into the GAS Address field, and the GAS AccessSize field is left
0 but most of the registers actually cannot be accessed using "ANY"
accesses.
As a conclusion, when AccessSize = 0 (ANY), the Address should either be
aligned to the BitWidth (wrong conversion) or aligned to 32 for PIO or 64
for MMIO (real GAS). Since currently, max_bit_width is 32, then:
1. BitWidth for the wrong conversion is 8,16,32; and
2. The Address of the real GAS should always be aligned to 8,16,32.
The address alignment check to exclude false matched real GAS is not
necessary. Thus this patch fixes the issue by removing the address
alignment check.
On the other hand, we in fact could use a simpler check of
"reg->bit_width < max_bit_width" to exclude the "BitWidth=64 PIO" case that
may be issued from acpi_read()/acpi_write() in the future.
Fixes: b314a172ee (ACPICA: Hardware: Add optimized access bit width support)
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit 059500940d (ACPI/video: export acpi_video_get_levels)
mistakenly dropped the correct value of max_level and that caused the
set_level function following failed and the acpi_video backlight interface
didn't get created. Fix this by passing back the correct max_level value.
While at it, also fix the param used in acpi_video_device_lcd_query_levels
where acpi_handle is expected but acpi_video_device is passed.
Fixes: 059500940d (ACPI/video: export acpi_video_get_levels)
Reported-and-tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zHa6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.7 rc1. They are based on a
commit earlier in the merge window and have been tested in linux-next
for a while.
MMC core:
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly"
* tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-acpi: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: sdhci-pci: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: longer timeout for long read time quirk
mmc: dw_mmc: rockchip: Set the drive phase properly
mmc: dw_mmc: fix the wrong max_blk_size
mmc: dw_mmc-rockchip: add MMC_CAP_CMD23 capabilities
mmc: sdhci-acpi: Ensure connected devices are powered when probing
ACPI / PM: Export acpi_device_fix_up_power()
mmc: block: Pause re-tuning while switched to the RPMB partition
mmc: block: Always switch back to main area after RPMB access
mmc: core: Add a facility to "pause" re-tuning
Just one fix for incorrect async_synchronize_cookie() usage in the
ACPI battery driver (Chris Wilson).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=rO5z
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.7-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Additional ACPI update for v4.7-rc1
Just one fix for incorrect async_synchronize_cookie() usage in the
ACPI battery driver (Chris Wilson)"
* tag 'acpi-4.7-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / battery: Correctly serialise with the pending async probe
1/ Device DAX for persistent memory:
Device DAX is the device-centric analogue of Filesystem DAX
(CONFIG_FS_DAX). It allows memory ranges to be allocated and mapped
without need of an intervening file system. Device DAX is strict,
precise and predictable. Specifically this interface:
a) Guarantees fault granularity with respect to a given page size
(pte, pmd, or pud) set at configuration time.
b) Enforces deterministic behavior by being strict about what fault
scenarios are supported.
Persistent memory is the first target, but the mechanism is also
targeted for exclusive allocations of performance/feature differentiated
memory ranges.
2/ Support for the HPE DSM (device specific method) command formats.
This enables management of these first generation devices until a
unified DSM specification materializes.
3/ Further ACPI 6.1 compliance with support for the common dimm
identifier format.
4/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Y3Xv
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this update was stabilized before the merge window and
appeared in -next. The "device dax" implementation was revised this
week in response to review feedback, and to address failures detected
by the recently expanded ndctl unit test suite.
Not included in this pull request are two dax topic branches (dax
error handling, and dax radix-tree locking). These topics were
deferred to get a few more days of -next integration testing, and to
coordinate a branch baseline with Ted and the ext4 tree. Vishal and
Ross will send the error handling and locking topics respectively in
the next few days.
This branch has received a positive build result from the kbuild robot
across 226 configs.
Summary:
- Device DAX for persistent memory: Device DAX is the device-centric
analogue of Filesystem DAX (CONFIG_FS_DAX). It allows memory
ranges to be allocated and mapped without need of an intervening
file system. Device DAX is strict, precise and predictable.
Specifically this interface:
a) Guarantees fault granularity with respect to a given page size
(pte, pmd, or pud) set at configuration time.
b) Enforces deterministic behavior by being strict about what
fault scenarios are supported.
Persistent memory is the first target, but the mechanism is also
targeted for exclusive allocations of performance/feature
differentiated memory ranges.
- Support for the HPE DSM (device specific method) command formats.
This enables management of these first generation devices until a
unified DSM specification materializes.
- Further ACPI 6.1 compliance with support for the common dimm
identifier format.
- Various fixes and cleanups across the subsystem"
* tag 'libnvdimm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (40 commits)
libnvdimm, dax: fix deletion
libnvdimm, dax: fix alignment validation
libnvdimm, dax: autodetect support
libnvdimm: release ida resources
Revert "block: enable dax for raw block devices"
/dev/dax, core: file operations and dax-mmap
/dev/dax, pmem: direct access to persistent memory
libnvdimm: stop requiring a driver ->remove() method
libnvdimm, dax: record the specified alignment of a dax-device instance
libnvdimm, dax: reserve space to store labels for device-dax
libnvdimm, dax: introduce device-dax infrastructure
nfit: add sysfs dimm 'family' and 'dsm_mask' attributes
tools/testing/nvdimm: ND_CMD_CALL support
nfit: disable vendor specific commands
nfit: export subsystem ids as attributes
nfit: fix format interface code byte order per ACPI6.1
nfit, libnvdimm: limited/whitelisted dimm command marshaling mechanism
nfit, libnvdimm: clarify "commands" vs "_DSMs"
libnvdimm: increase max envelope size for ioctl
acpi/nfit: Add sysfs "id" for NVDIMM ID
...
async_synchronize_cookie() only serialises all tasks up to the specified
cookie, and importantly does not wait for the task corresponding with
the cookie. [This is so that it can be trivially used from inside the
async_func_t in order to serialise with all preceding tasks.] In order
to serialise with acpi_battery_init_async() we need to compensate and
pass in the next cookie instead.
The impact today is zero since performing an async_schedule() from inside
a module init function will trigger an async_synchronize_full() prior to
the module loader's completion. However, if the probe was moved to its
own unregistered async_domain, then the async_synchronize_cookie would
be replaced with an async_synchronize_full_domain.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers that needs acpi_device_fix_up_power(), allow them to be built as
modules by exporting this function.
Cc: <stable@vger.kernel.org> # 4.5+
Tested-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
* acpica: (41 commits)
ACPICA: Update version to 20160422
ACPICA: Move all ASCII utilities to a common file
ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()
ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support in acpi_hw_read()
ACPICA: Executer: Introduce a set of macros to handle bit width mask generation
ACPICA: Hardware: Add optimized access bit width support
ACPICA: Utilities: Add ACPI_IS_ALIGNED() macro
ACPICA: Renamed some #defined flag constants for clarity
ACPICA: ACPI 6.0, tools/iasl: Add support for new resource descriptors
ACPICA: ACPI 6.0: Update _BIX support for new package element
ACPICA: ACPI 6.1: Support for new PCCT subtable
ACPICA: Refactor evaluate_object to reduce nesting
ACPICA: Divergence: remove unwanted spaces for typedef
ACPICA: Update version to 20160318
ACPICA: Namespace: Reorder \_SB._INI to make sure it is evaluated before _REG evaluations
ACPICA: Events: Fix an issue that _REG association can happen before namespace is initialized
ACPICA: Tables: Fix wrong MLC condition for dynamic table loading
ACPICA: Interpreter: Fix wrong conditions for acpi_ev_install_region_handlers() invocation
ACPICA: Hardware: Enhance acpi_hw_validate_register() with access_width/bit_offset awareness
Utilities: Fix missing parentheses in ACPI_GET_BITS()/ACPI_SET_BITS()
...
The Makefile/Kconfig currently controlling compilation of this code is:
Makefile:acpi-$(CONFIG_ACPI_REDUCED_HARDWARE_ONLY) += evged.o
drivers/acpi/Kconfig:config ACPI_REDUCED_HARDWARE_ONLY
drivers/acpi/Kconfig: bool "Hardware-reduced ACPI support only" if EXPERT
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
code there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
The file wasn't explicitly including the module.h file but it did
already have init.h so, unlike similar changes, this one has no
header changes at all.
We also delete the MODULE_LICENSE tag since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix for a recent regression in the intel_pstate driver causing
it to fail to restore the HWP (HW-managed P-states) configuration
of the boot CPU after suspend-to-RAM (Rafael Wysocki).
- Fix for two recent regressions in the intel_pstate driver, one
that can trigger a divide by zero if the driver is accessed via
sysfs before it manages to take the first sample and one causing
it to fail to update a structure field used in a trace point, so
the information coming from it is less useful (Rafael Wysocki).
- Fix for a problem in the sti-cpufreq driver introduced during
the 4.5 cycle that causes it to break CPU PM in multi-platform
kernels by registering cpufreq-dt (which subsequently doesn't
work) unconditionally and preventing the driver that would
actually work from registering (Sudeep Holla).
- Stable-candidate fix for an ARM64 cpuidle issue causing idle
state usage counters to be incorrectly updated for idle states
that were not entered due to errors (James Morse).
- Fix for a recently introduced issue in the OPP (Operating
Performance Points) framework causing it to print bogus error
messages for missing optional regulators (Viresh Kumar).
- Fix for a recently introduced issue in the generic device
properties framework that may cause it to attempt to dereferece
and invalid pointer in some cases (Heikki Krogerus).
- Fix for a deadlock in the ACPICA core that may be triggered
by device (eg. Thunderbolt) hotplug (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=pU+A
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for problems introduced or discovered recently (intel_pstate,
sti-cpufreq, ARM64 cpuidle, Operating Performance Points framework,
generic device properties framework) and one fix for a hotplug-related
deadlock in ACPICA that's been there forever, but is nasty enough.
Specifics:
- Fix for a recent regression in the intel_pstate driver causing it
to fail to restore the HWP (HW-managed P-states) configuration of
the boot CPU after suspend-to-RAM (Rafael Wysocki).
- Fix for two recent regressions in the intel_pstate driver, one that
can trigger a divide by zero if the driver is accessed via sysfs
before it manages to take the first sample and one causing it to
fail to update a structure field used in a trace point, so the
information coming from it is less useful (Rafael Wysocki).
- Fix for a problem in the sti-cpufreq driver introduced during the
4.5 cycle that causes it to break CPU PM in multi-platform kernels
by registering cpufreq-dt (which subsequently doesn't work)
unconditionally and preventing the driver that would actually work
from registering (Sudeep Holla).
- Stable-candidate fix for an ARM64 cpuidle issue causing idle state
usage counters to be incorrectly updated for idle states that were
not entered due to errors (James Morse).
- Fix for a recently introduced issue in the OPP (Operating
Performance Points) framework causing it to print bogus error
messages for missing optional regulators (Viresh Kumar).
- Fix for a recently introduced issue in the generic device
properties framework that may cause it to attempt to dereferece and
invalid pointer in some cases (Heikki Krogerus).
- Fix for a deadlock in the ACPICA core that may be triggered by
device (eg Thunderbolt) hotplug (Prarit Bhargava)"
* tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Remove useless check
ACPICA: Dispatcher: Update thread ID for recursive method calls
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
device property: Avoid potential dereferences of invalid pointers
Module option to limit userspace to the publicly defined command set.
For cases where private DIMM commands may be interfering with the
kernel's handling of DIMM state this option can be set to block vendor
specific commands.
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
