IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The BL32/TEE reserved-memory region is now inherited from the common
family dtsi (meson-g12-common) so we can drop it from board files.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220126044954.19069-4-christianshewitt@gmail.com
The Khadas VIM3 shares the eMMC pins 4 to 7 with the SPI NOR, in order
to enable the eMMC and the SPI NOR interface, we need to omit the
4 last pins from the eMMC pinctrl.
As it was done for the Khadas VIM2, split the eMMC pinctrls in ctrl, data
and ds pins with either 4bits data or 8bits data, and update the current
board accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200313090713.15147-2-narmstrong@baylibre.com
A codec node of the sei510 sound card is numbered with the pattern
codec@XX. This pattern should be used only if there is a reg property in
the node which is not case here. Change this to something acceptable.
This change is only to better comply with the DT spec. No functional
changes expected.
Fixes: 64c10554bf9c ("arm64: dts: meson: sei510: add sound card")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200224150812.263980-4-jbrunet@baylibre.com
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board
by setting the clock, OPP and supply for each CPU cores.
The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM
output clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations and checking the final
frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the IR receiver controller on the SEI510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the sei510:
* TDM interface A is connected to an external DAC and a speaker installed
on the device.
* HDMI is expected to use TDM B. It can also use TDM A but will be
limited to 2 channels, as accepted by the external DAC.
* 2 Built in PDM mics through the PDM interface.
* Both TDM outputs may use HW loopback.
The internal DAC connected to audio jack will be added later on, when
driver support is added.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SEI510 board features a max98357a audio codec for built-in
speaker
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Setting to 2Mbaud/s is the nominal bus speed for common usages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 32k low power clock is necessary for the bluetooth part of the
combo module to initialize correctly, simply add the same clock we
use for the sdio pwrseq.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SEI510 embeds an AP6398S SDIO module, let's add the
corresponding SDIO, PWM clock and mmc-pwrseq nodes.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the network interface of the SEI510 which use the internal PHY.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable eMMC and SDCard on the g12a sei510 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Like order boards, order nodes by address then node names then aliases.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the SEI510 STB.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the USB2 and USB3 Host ports on the SEI520 Set-Top-Box.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the :
- ADC Touch key
- Bluetooth Module on UART A
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SEI Robotics SEI510 Board is based on the Amlogic G12A S905X2
and has the following features :
- Amlogic G12A S905X2 SoC
- 10/100 Ethernet
- USB2 + USB3 ports
- Micro SDCard Port
- Audio + CVBS AV Jack port
- HDMI 2.1 + CEC Port
- ADC Touch Button
- Far-Field Microphone Array + Mono HP
- IR Sensor
- IR Emmiter LED Array
- RGB Led
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: sorted Makefile entry alphabetcially]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
