IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Previously using dma_alloc_wc() API we created cache coherent
(mapped as write-back) mappings.
Because we disable MMU600 snooping it was required to do costly
page walk and cache flushes after each page table modification.
With write-combined buffers it's possible to do a single write memory
barrier to flush write-combined buffer to memory which simplifies the
driver and significantly reduce time of map/unmap operations.
Mapping time of 255 MB is reduced from 2.5 ms to 500 us.
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-7-stanislaw.gruszka@linux.intel.com
Waking up process, which wait for particular condition, will go to
sleep again on wake_up() if the condition is not met. Add abort flag
to wake up IPC receivers, which will finish with -ECANCELED error.
This is only needed for reset, run time power management prevent to
suspend VPU when there is pending IPC processing or pending job.
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-5-stanislaw.gruszka@linux.intel.com
Stop job_done thread when going to suspend. Use kthread_park() instead
of kthread_stop() to avoid memory allocation and potential failure
on resume.
Use separate function as thread wake up condition. Use spin lock to assure
rx_msg_list is properly protected against concurrent access. This avoid
race condition when the rx_msg_list list is modified and read in
ivpu_ipc_recive() at the same time.
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-4-stanislaw.gruszka@linux.intel.com
We should not leave device half enabled if there is failure somewhere
it power up sequence. Fix device init and resume paths.
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-3-stanislaw.gruszka@linux.intel.com
Profiling freq is a debug firmware feature. It switches default clock
to higher resolution for fine-grained and more accurate firmware task
profiling. We already configure it during boot up of VPU4.
Add debugfs knob and helpers per HW generation that allow to change it.
For vpu37xx the implementation is empty as profiling frequency can only
be changed on VPU4 or newer.
Signed-off-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-2-stanislaw.gruszka@linux.intel.com
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R. Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)
-----BEGIN PGP SIGNATURE-----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=0iVF
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
drm-misc-next for v6.7-rc1:
drm-misc-next-2023-10-19 + following:
UAPI Changes:
Cross-subsystem Changes:
- Convert fbdev drivers to use fbdev i/o mem helpers.
Core Changes:
- Use cross-references for macros in docs.
- Make drm_client_buffer_addb use addfb2.
- Add NV20 and NV30 YUV formats.
- Documentation updates for create_dumb ioctl.
- CI fixes.
- Allow variable number of run-queues in scheduler.
Driver Changes:
- Rename drm/ast constants.
- Make ili9882t its own driver.
- Assorted fixes in ivpu, vc4, bridge/synopsis, amdgpu.
- Add planar formats to rockchip.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3d92fae8-9b1b-4165-9ca8-5fda11ee146b@linux.intel.com
Currently the VPU firmware prepares for D0i3 every time the VPU
is entering D0i2 Idle state. This is not optimal as we might not
enter D0i3 every time we enter D0i2 Idle and this preparation
is quite costly.
This optimization moves D0i3 preparation to a dedicated
message sent from the host driver only when the driver is about
to enter D0i3 - this reduces power consumption and latency for
certain workloads, for example audio workloads that submit
inference every 10 ms.
The VPU needs non zero time to enter IDLE state after responding to
D0i3 entry message. If the driver does not wait for the VPU to enter
IDLE state it could cause warm boot failures.
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-12-stanislaw.gruszka@linux.intel.com
Split ivpu_ipc_send_receive() implementation to have a version
that does not call pm_runtime_resume_and_get(). That implementation
can be invoked when device is up and runtime resume is prohibited
(for example at the end of boot sequence).
The new function will be used for D0i3 entry IPC message addition
in the separate change.
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-10-stanislaw.gruszka@linux.intel.com
The firmware needs to know the time spent in D0i3/D3 to
calculate telemetry data. The D0i3/D3 residency time is
calculated by the driver and passed to the firmware
in the boot parameters.
The driver also passes VPU perf counter value captured
right before entering D0i3 - this allows the VPU firmware
to generate monotonic timestamps for the logs.
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-9-stanislaw.gruszka@linux.intel.com
The driver needs to capture the D0i3 entry timestamp to
calculate D0i3 residency time.
The D0i3 residency time and the VPU timestamp are passed
to the firmware at D0i3 exit (warm boot).
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-8-stanislaw.gruszka@linux.intel.com
Change meaning of test_mode module parameter from integer value
to bitmask allowing setting different test features with corresponding
bits.
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-7-stanislaw.gruszka@linux.intel.com
Add test_mode = 3 that add VPU_JOB_FLAGS_NULL_SUBMISSION_MASK
flag to the job send to the VPU device. Then the VPU will process
the job but won't execute commands (except the command to signal
the fence).
This can be used to estimate job processing overhead in the host
software and VPU firmware.
Unlike the null hardware mode, the null submission mode will
still work even if UMD uses VPU fences to track job completion.
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-6-stanislaw.gruszka@linux.intel.com
Setting a non-zero work point resets the IP hence IP_RESET
trigger is redundant.
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-5-stanislaw.gruszka@linux.intel.com
Add new debugfs file to set dvfs_mode FW boot parameter and restart
the FW to allow experimenting with DVFS (dynamic voltage & frequency
scaling).
Signed-off-by: Tomasz Rusinowicz <tomasz.rusinowicz@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-4-stanislaw.gruszka@linux.intel.com
The usage count of struct dev_pm_info is an implementation detail that
is only available if CONFIG_PM is enabled, so printing it in a debug message
causes a build failure in configurations without PM:
In file included from include/linux/device.h:15,
from include/linux/pci.h:37,
from drivers/accel/ivpu/ivpu_pm.c:8:
drivers/accel/ivpu/ivpu_pm.c: In function 'ivpu_rpm_get_if_active':
drivers/accel/ivpu/ivpu_pm.c:254:51: error: 'struct dev_pm_info' has no member named 'usage_count'
254 | atomic_read(&vdev->drm.dev->power.usage_count));
| ^
include/linux/dev_printk.h:129:48: note: in definition of macro 'dev_printk'
129 | _dev_printk(level, dev, fmt, ##__VA_ARGS__); \
| ^~~~~~~~~~~
drivers/accel/ivpu/ivpu_drv.h:75:17: note: in expansion of macro 'dev_dbg'
75 | dev_dbg((vdev)->drm.dev, "[%s] " fmt, #type, ##args); \
| ^~~~~~~
drivers/accel/ivpu/ivpu_pm.c:253:9: note: in expansion of macro 'ivpu_dbg'
253 | ivpu_dbg(vdev, RPM, "rpm_get_if_active count %d\n",
| ^~~~~~~~
The print message does not seem essential, so the easiest workaround is
to just remove it.
Fixes: c39dc15191c4 ("accel/ivpu: Read clock rate only if device is up")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231027152633.528490-1-arnd@kernel.org
Use QAIC_TIMESYNC MHI channel to send UTC time to device in SBL
environment. Remove support for QAIC_TIMESYNC MHI channel in AMSS
environment as it is not used in that environment.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016170114.5446-3-quic_jhugo@quicinc.com
Device and Host have a time synchronization mechanism that happens once
during boot when device is in SBL mode. After that, in mission-mode there
is no timesync. In an experiment after continuous operation, device time
drifted w.r.t. host by approximately 3 seconds per day. This drift leads
to mismatch in timestamp of device and Host logs. To correct this
implement periodic timesync in driver. This timesync is carried out via
QAIC_TIMESYNC_PERIODIC MHI channel.
Signed-off-by: Ajit Pal Singh <quic_ajitpals@quicinc.com>
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016170114.5446-2-quic_jhugo@quicinc.com
Several virtualization use-cases either don't support 32 MultiMSIs
(Xen/VMware) or have significant drawbacks to their use (KVM's vIOMMU,
which is required to support 32 MSI, needs to allocate an alternate
system memory space for each device using vIOMMU (e.g. 8GB VM mem and
2 cards => 8 + 2 * 8 = 24GB host memory required)). Support these
cases by enabling a 1 MSI fallback mode.
Whenever all 32 MSIs requested are not available, a second request for
a single MSI is made. Its success is the initiator of single MSI mode.
This mode causes all interrupts generated by the device to be directed
to the 0th MSI (firmware >=v1.10 will do this as a response to the PCIe
MSI capability configuration). Likewise, all interrupt handlers for the
device are registered to the 0th MSI.
Since the DBC interrupt handler checks if the DBC is in use or if
there is any pending changes, the 'spurious' interrupts are
disregarded. If there is work to be done, the standard threaded IRQ
handler is dispatched.
On every interrupt, the MHI handler wakes up its threaded interrupt
handler, and attempts to wake any waiters for MHI state events.
Performance is within +-0.6% for test cases that typify real world
use. Larger differences ([-4,+132]%, avg +47%) exist for very simple
tasks (e.g. addition) compiled for single NSPs. It is assumed that the
small work and many interrupts typically cause contention (e.g. 16 NSPs
vs 4 CPUs), as evidenced by the standard deviation between runs also
decreasing (r=-0.48 between delta(Performace_test) and
delta(StdDev_test/Avg_test))
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016170036.5409-1-quic_jhugo@quicinc.com
Move sequence of masking and unmasking global interrupts from buttress
interrupt handler to generic one that handles both VPUIP and BTRS
interrupts. Unmasking global interrupts will re-trigger MSI for any
pending interrupts.
Lack of this sequence will cause the driver to miss any
VPUIP interrupt that comes after reading VPU_37XX_HOST_SS_ICB_STATUS_0
and before clearing all active interrupt sources.
Fixes: 35b137630f08 ("accel/ivpu: Introduce a new DRM driver for Intel VPU")
Cc: stable@vger.kernel.org
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024161952.759914-1-stanislaw.gruszka@linux.intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The work items listed in the TODO file of this driver file are either
completed or dropped. The file is no more significant according
to the maintainers. Hence removing it from the sources.
Suggested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Deepak R Varma <drv@mailo.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZTAucrOT69/tQK2o@runicha.com
Introduce ivpu_jsm_msg_type_to_str() helper to print type of IPC
message. This will make reading logs and debugging IPC issues easier.
Co-developed-by: Maciej Falkowski <maciej.falkowski@intel.com>
Signed-off-by: Maciej Falkowski <maciej.falkowski@intel.com>
Signed-off-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020104501.697763-5-stanislaw.gruszka@linux.intel.com
Do not unnecessarily wake up device to read clock rate.
Return 0 as clk_rate if device is suspended.
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020104501.697763-4-stanislaw.gruszka@linux.intel.com
Remove two out of four _POLL macros. For two remaining _POLL
macros add message about polling register start and finish.
Additionally avoid inconsequence when using REGV_WR/RD macros in
MMU code - passing raw register offset instead of register name.
Signed-off-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020104501.697763-3-stanislaw.gruszka@linux.intel.com
Quite often during test corner cases IPC, JSM functions can flood
dmesg with warn or err messages. With that lost dmesg history.
Change warn, err to ratelimited versions in IPC, JSM to suppress
dmesg spam occurrence during fail test scenarios.
Signed-off-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020104501.697763-2-stanislaw.gruszka@linux.intel.com
Allow to use whole address range in MMU context mmap which is up to 48
bits. Return invalid argument from MMU context mmap in case address is
not aligned to MMU page size, address is below MMU page size or address
is greater then 47 bits.
This fixes problem disallowing to run large models on VPU4
Signed-off-by: Wludzik, Jozef <jozef.wludzik@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018110113.547208-1-stanislaw.gruszka@linux.intel.com
This reverts commit 645d694559cab36fe6a57c717efcfa27d9321396.
The commit cause issues with memory access from the device side.
Switch back to write-combined memory mappings until the issues
will be properly addressed.
Add extra wmb() needed when boot_params->save_restore_ret_address() is
modified.
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017121353.532466-1-stanislaw.gruszka@linux.intel.com
The notable changes are:
- uAPI changes:
- Expose tsc clock sampling to better sync clock information in profiler.
- Enhance engine error reporting in the info ioctl.
- Block access to the eventfd operations through the control device.
- Disable the option of the user to register multiple times with the same
offset for timestamp dump by the driver. If a user wants to use the same
offset in the timestamp buffer for different interrupt, it needs to first
de-register the offset.
- When exporting dma-buf (for p2p), force the user to specify size/offset
in multiples of PAGE_SIZE. This is instead of the driver doing the
rounding to PAGE_SIZE, which has caused the driver to map more memory
than was intended by the user.
- New features and improvements:
- Complete the move of the driver to the accel subsystem by removing the
custom habanalabs class and major and registering to accel subsystem.
- Move the firmware interface files to include/linux/habanalabs. This is
a pre-requisite for upstreaming the NIC drivers of Gaudi (as they need to
include those files).
- Perform device hard-reset upon PCIe AXI drain event to prevent the failure
from cascading to different IP blocks in the SoC. In secured environments,
this is done automatically by the firmware.
- Print device name when it is removed for better debuggability.
- Add support for trace of dma map sgtable operations.
- Optimize handling of user interrupts by splitting the interrupts to two
lists. One list for fast handling and second list for handling with
timestamp recording, which is slower.
- Prevent double device hard-reset due to 2 adjacent H/W events.
- Set device status 'malfunction' while in rmmod.
- Firmware related fixes:
- Extend preboot timeout because preboot loading might take longer than
expected in certain cases.
- Add a protection mechanism for the Event Queue. In case it is full, the
firmware will be able to notify about it through a dedicated interrupt.
- Perform device hard-reset in case scrubbing of memory has failed.
- Bug fixes and code cleanups:
- Small fixes of dma-buf handling in Gaudi2, such as handling an offset != 0,
using the correct exported size, creation of sg table.
- Fix spmu mask creation.
- Fix bug in wait for cs completion for decoder workloads.
- Cleanup Greco name from documentation.
- Fix bug in recording timestamp during cs completion interrupt handling.
- Fix CoreSight ETF configuration and flush logic.
- Fix small bug in hpriv_list handling (the list that contains the private
data per process that opens our device).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmUlHoQACgkQZR1NuKta
54DsXQf8CW+W4iWJf5UDTj/E/giu9rVRrsUsU0hhCcXbecIxRsLObYXtulENu5/u
VuEAo/tAvo0LUKi8pdIv6ernDKaxZ1+fimlfXMCzllAA/ts3yp1NgunprsIsx3tv
YgcJ2GNR8UlVZ1qYuZl+4dOTyD0yfRMROUXBe7wqKnUXOEepOiLBxq6W15tZiJnx
L+V0yGkNk6pAoADIXLW9EgEXiN/bJZCXGPWp06i/Nz7cHIHJGoV59wAqftqllCtk
8ZMkLByjlQKPhc5AgWBtKE8EGVip3sm7b/Q2Gq0ZXdZiebyVJ+AjuuDOdtq1UCIw
Rcp2576E7rByIBu3RAFlrioWhuR5Zw==
=2ien
-----END PGP SIGNATURE-----
Merge tag 'drm-habanalabs-next-2023-10-10' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into drm-next
This tag contains habanalabs driver changes for v6.7.
The notable changes are:
- uAPI changes:
- Expose tsc clock sampling to better sync clock information in profiler.
- Enhance engine error reporting in the info ioctl.
- Block access to the eventfd operations through the control device.
- Disable the option of the user to register multiple times with the same
offset for timestamp dump by the driver. If a user wants to use the same
offset in the timestamp buffer for different interrupt, it needs to first
de-register the offset.
- When exporting dma-buf (for p2p), force the user to specify size/offset
in multiples of PAGE_SIZE. This is instead of the driver doing the
rounding to PAGE_SIZE, which has caused the driver to map more memory
than was intended by the user.
- New features and improvements:
- Complete the move of the driver to the accel subsystem by removing the
custom habanalabs class and major and registering to accel subsystem.
- Move the firmware interface files to include/linux/habanalabs. This is
a pre-requisite for upstreaming the NIC drivers of Gaudi (as they need to
include those files).
- Perform device hard-reset upon PCIe AXI drain event to prevent the failure
from cascading to different IP blocks in the SoC. In secured environments,
this is done automatically by the firmware.
- Print device name when it is removed for better debuggability.
- Add support for trace of dma map sgtable operations.
- Optimize handling of user interrupts by splitting the interrupts to two
lists. One list for fast handling and second list for handling with
timestamp recording, which is slower.
- Prevent double device hard-reset due to 2 adjacent H/W events.
- Set device status 'malfunction' while in rmmod.
- Firmware related fixes:
- Extend preboot timeout because preboot loading might take longer than
expected in certain cases.
- Add a protection mechanism for the Event Queue. In case it is full, the
firmware will be able to notify about it through a dedicated interrupt.
- Perform device hard-reset in case scrubbing of memory has failed.
- Bug fixes and code cleanups:
- Small fixes of dma-buf handling in Gaudi2, such as handling an offset != 0,
using the correct exported size, creation of sg table.
- Fix spmu mask creation.
- Fix bug in wait for cs completion for decoder workloads.
- Cleanup Greco name from documentation.
- Fix bug in recording timestamp during cs completion interrupt handling.
- Fix CoreSight ETF configuration and flush logic.
- Fix small bug in hpriv_list handling (the list that contains the private
data per process that opens our device).
Signed-off-by: Dave Airlie <airlied@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmUlHoQACgkQZR1NuKta
# 54DsXQf8CW+W4iWJf5UDTj/E/giu9rVRrsUsU0hhCcXbecIxRsLObYXtulENu5/u
# VuEAo/tAvo0LUKi8pdIv6ernDKaxZ1+fimlfXMCzllAA/ts3yp1NgunprsIsx3tv
# YgcJ2GNR8UlVZ1qYuZl+4dOTyD0yfRMROUXBe7wqKnUXOEepOiLBxq6W15tZiJnx
# L+V0yGkNk6pAoADIXLW9EgEXiN/bJZCXGPWp06i/Nz7cHIHJGoV59wAqftqllCtk
# 8ZMkLByjlQKPhc5AgWBtKE8EGVip3sm7b/Q2Gq0ZXdZiebyVJ+AjuuDOdtq1UCIw
# Rcp2576E7rByIBu3RAFlrioWhuR5Zw==
# =2ien
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 10 Oct 2023 19:51:00 AEST
# gpg: using RSA key ED311BA00042EF52DCB412C5651D4DB8AB5AE780
# gpg: Can't check signature: No public key
From: Oded Gabbay <ogabbay@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZSUfiX4J7v4Wn0cU@ogabbay-vm-u22.habana-labs.com
Use:
- ivpu_bo_vaddr(bo) instead of bo->kvaddr
- ivpu_bo_size(bo) instead of bo->base.size
This is a preparation for switch to a drm_gem_shmem_object as a base for
ivpu_bo, where:
- bo->kvaddr becomes bo->base.vaddr
- bo->base.size becomes bo->base.base.size
Using ivpu_bo_vaddr() and ivpu_bo_size() increases the readability of
the code.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901094957.168898-9-stanislaw.gruszka@linux.intel.com
event_types_num received from the user can be 0. In that case, the
event_mask should be 0.
In addition, to create a correct mask we need to match the number
of event types to the bit location such that bit 0 represents a single
event type, bit 1 represents 2 types and so on.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Ofir Bitton <obitton@habana.ai>
Non-completed transactions from PCIe towards the device are handled by
the AXI drain mechanism. This handling is in the PCIe level, but the
transactions are still there in the device consuming some queues
entries, and therefore the device must be reset.
Modify to perform hard-reset upon PCIe AXI drain events.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The decoder interrupts are handled in the interrupt context
same as all user interrupts.
In such case, the wait list should be protected by
spin_lock_irqsave in order to avoid deadlock that might happen
with the user submission flow.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The function does not pin the pages so remove that from the inline doc.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Two function stubs were removed in an earlier commit but are now needed
again:
drivers/accel/habanalabs/common/device.c: In function 'hl_device_init':
drivers/accel/habanalabs/common/device.c:2231:14: error: implicit declaration of function 'hl_debugfs_device_init'; did you mean 'drm_debugfs_dev_init'? [-Werror=implicit-function-declaration]
2231 | rc = hl_debugfs_device_init(hdev);
drivers/accel/habanalabs/common/device.c:2367:9: error: implicit declaration of function 'hl_debugfs_device_fini'; did you mean 'hl_debugfs_remove_file'? [-Werror=implicit-function-declaration]
2367 | hl_debugfs_device_fini(hdev);
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This code was added as part of a bigger feature which was never
upstreamed, so remove this code.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Ofir Bitton <obitton@habana.ai>
Notifies the user which device was removed. It is important in
a server with multiple devices.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Ofir Bitton <obitton@habana.ai>
flags in struct wait_interrupt_data is not used anywhere so remove it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Ofir Bitton <obitton@habana.ai>
Traces the DMA [un]map_sgtable using the new traces we added.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
