IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Use ACCESS_ONCE to reduce the number of redundant loads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of variable reloads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is no longer necessary for preparing mac80211 tx status
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local variables to reduce the number of load/store operations on uncached
memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the slot time based on the mac80211 short slot vs long slot setting
instead of just forcing long slot for all CCK-enabled channels.
This slightly improves 802.11g mode performance in in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k uses 8 usec as a sifs time, extracted from the initvals, whereas the
standard requires a sifs time of 10. The difference originates from the fact
that the SIFS register has an offset of 2 usec.
Fix the SIFS time definition to use the standard value of 10 usec and subtract
2 usecs when writing the SIFS register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Subtract the difference in preamble duration (in usec) from the value
returned by ieee80211_generic_frame_duration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During normal operation, minstrel was showing suspicious EWMA probabilities
exceeding 100%. It looks like the tx status reporting in ath5k was not
properly clearing the rate index for rates which were never attempted.
This is caused by uninitialized stale data in the on-stack tx status
information, which is reused when more frames are received.
To fix this, rely on ts->ts_final_idx to select the last attempted rate,
instead of checking whether ts->ts_rate is set.
Additionally, the conversion from the driver rate index back to the
mac80211 rate index can be dropped, as the mac80211 tx status will still
have the original rate index which was used to set up the descriptor.
Additionally, one more inaccuracy was fixed - the final rate attempt
count only needs to be increased by one if the transmission attempt was
successful.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k driver does kmalloc allocations for pcal info in a loop.
But, if one fails it was simply returning -ENOMEM without freeing
already allocated memory. This patch corrects that oversight.
Reported-by: Eugene A. Shatokhin <dame_eugene@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update Tx gain 23 for all tx gain table.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org>
Reported-by: Joe Culler <joe.culler@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is nowhere used.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This does not seems to be used anywhere so remove it.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's easier to read and it slightly decreases code size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
