IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Using this logic breaks driver unload, this is a temporary fix
a followup patch will properly fix this
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD not going to be high if Panel VDD is off
And all AUX transaction will fail :(
[How]
1. Power on VDD before attempting detection if it isn't already on
2. Improve the robustness by having a retry mechanism on the
first DPCD read after VDD on. If a particular board always holds
HPD high incorrectly, the AUX access may fail, so we can retry
in those scenarios. This change would only improve logic
since it prevents AUX failure leading to bad resolution on internal
panel.
3. We should never need to re-detect internal panel, so logic
is re-arranged a bit to skip earlier.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Add i2c_hw_Status check to make sure when HW i2c is in use.
2. Don't reset HW engine in is_hw_busy() and instead do this in
process_transaction() because SW i2c does not check if hw i2c is in use
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to assert just return
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some panels return a link rate of 0 (unknown) in DPCD 0. In this case,
an appropriate mode cannot be set, and certain panels will show
corruption as they are forced to use a mode they do not support.
[HOW]
Read DPCD 10 in the case where supported link rate from DPCD 0 is
unknown, and pass that value on to the reported link rate.
This re-introduces behaviour present in previous versions that appears
to have been accidentally removed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tao.Huang <Tao.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The module parameter to specify the default ABM level is now defined,
so hook it up in DM.
[How]
On connector reset specify the default level. DC will program this as
part of the modeset since it gets passed onto the stream in
dm_update_crtc_state.
It's only set for eDP connectors, but it doesn't matter if this is
specified for connectors or hardware that doesn't support ABM.
It's DC's responsibility to check that ABM can be set or adjusted, and
DC does check that the DMCU firmware is running and if there's backlight
control available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's non trivial to configure or specify an ABM reduction level for
userspace outside of X. There is also no method to specify the default
ABM value at boot time.
A parameter should be added to configure this.
[How]
Expose a module parameter that can specify the default ABM level to
use for eDP connectors on DC enabled hardware that loads the DMCU
firmware.
The default is still disabled (0), but levels can range from 1-4. Levels
control how much the backlight can be reduced, with being the least
amount of reduction and four being the most reduction.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's incorrect to do soft reset for SRIOV, when GFX
hang the WREG would stuck there becuase it goes KIQ way.
the GPU reset counter is incorrect: always increase twice
for each timedout
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since Hardware bug, GDS exist ECC error after cold boot up,
adding GDS clearing workaround in later init for gfx9.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.
Poor performance and stuttering can occur when many of these commits
are frequently issued.
This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.
[How]
Drop the check for state->allow_modeset in should_reset_plane.
All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC
These conditions are all covered in should_reset_plane.
We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.
But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.
[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.
Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This option is no longer needed. The default code paths
are now the only option.
v2: Add HPAGE support and a default for non contiguous maps
v3: Misread 512 pages as MiB ...
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.
[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.
Example:
cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10
v2: Drop unneeded connector status check
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use SMU firmware version to indentify the raven1 refresh device and
then load homologous RLC FW.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Suggested-by: Huang Rui<Ray.Huang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add gfxoff_state_changed_by_workload to control gfxoff
when set power_profile_mode
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under Vega10 SR-IOV VF, L1 register access mode should be enabled by
default as the non-security VF will no longer be supported.
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ported from gfx8, no changes in register setup.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Translate queue priority into pipe priority and write to MQDs.
The priority values are used to perform queue and pipe arbitration.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Always mark evicted queues with q->properties.is_evicted = true, even
queues that are inactive for other reason. This simplifies maintaining
the eviction state as it doesn't require updating is_evicted when other
queue activation conditions change.
On the other hand, we now need to check those other queue activation
conditions whenever an evicted queues is restored. To minimize code
duplication, move the queue activation check into a macro so it can be
maintained in one central place.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Cox <Philip.Cox@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
EDC counts are related to instance and se. They are not the same
for different type of EDC. EDC clearing are changed to base on
individual EDC's instance and SE number.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.
This caused numerous regressions on DCN1_01 when loading the driver.
[How]
Add it back.
Fixes: 97df424fe7a7 ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.
During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.
During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.
Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:
BUG_ON(dm_new_crtc_state->stream == NULL);
...since the old stream is gone from the context and the new stream is
also still NULL.
[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This avoids OOM situations when we have lots of threads
submitting at the same time.
v3: apply this to the whole driver, not just CS
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And only move them in on validation. This allows for better control
when multiple processes are fighting over those resources.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The messages about amdgpu_cs_list_validate are duplicated because the
caller will complain into the logs as well and we can also get
interrupted by a signal here.
Also fix the the caller to not report -EAGAIN from validation.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ras ta interface header need to be updated to match with latest ta fw updates
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu:
- Revert timeline support until KHR is ready
- Various driver reload fixes
- Refactor clock handling in DC
- Aux fixes for DC
- Bandwidth calculation updates for DC
- Fix documentation due to file rename
- RAS fix
- Fix race in late_init
ttm:
- Allow for better forward progress when there is heavy memory contention
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606032537.6939-1-alexander.deucher@amd.com
This reverts commit 8d8a5a64a8904ea32bbf7292b89c11156d64f9a1.
Wait until KHR exposes the VLK support.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These got added back by subsequent merges accidently.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split late_init into two functions, one (do_late_init) which
just does the hw init, and late_init which calls do_late_init
and schedules the IB test work. Call do_late_init in
the GPU reset code to run the init code, but not schedule
the IB test code. The IB test code is called directly
in the gpu reset code so no need to run the IB tests
in a separate work thread. If we do, we end up racing.
v2: Rework late_init. Pull out the mgpu fan boost and xgmi
pstate code into late_init so they get called in all cases.
rename the late_init worker thread to delayed work since it's
just the IB tests now which can happen later. Schedule the
work at init and resume time. It's not needed at reset time
because the IB tests are called directly.
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Xinhui Pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gpu reset will run late_init and schedule the late_init_work. if we
keep triggering gpu reset in a short time, there are potenial races.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
-----BEGIN PGP SIGNATURE-----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=GrAP
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c43ffa9-11ff-5354-d772-c20fd4d1e3d9@linux.intel.com
[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.
This avoids unnecessary blanking for simple metadata updates.
[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com
[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.
[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.
When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.
The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com
add ticket for display bo, so that it can preempt busy bo.
v2: fix stupid rebase error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are already doing this for DMA-buf imports and also for
amdgpu VM BOs for quite a while now.
If this doesn't run into any problems we are probably going
to stop removing BOs from the LRU altogether.
v2: drop BUG_ON from ttm_bo_add_to_lru
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G OE 5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808] drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.
Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu
Root cause:
When unload driver, it doesn't unregister aux.
v2: Don't use has_aux
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the VF, some registers only could be programmed with RLC.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Trigger Huang <Trigger.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
