IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:
... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two type of i.MX8MM EVK board, one is populated with
LPDDR4(default dts), and one is populated with DDR4. these two
boards share most of the board design, but still have some difference.
imx8mm-evk has emmc support, imx8mm-ddr4-evk has gpmi nand support.
And also, the BT/WIFI module is different. So move the common dts
part into imx8mm-evk.dtsi for reuse.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Device tree schema expects regulator names to be lowercase. This fixes
dtbs_check warnings like:
pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-6]$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use preferred properties of phy node instead of deprecated
phy-reset-gpios (and others). This avoids copying deprecated code into
future DTSes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "pinctrl-names" property in iomux node does not make sense on its
own (without "pinctrl-X").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-evk has a quad SPI-NOR flash on the flexspi bus.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With these two parameters tuning, it can pass USB eye diagram at evk board.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group
(1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups
have been supported at bd718x7-regulator driver, hence, just corrrect the
voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too.
Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mm
datasheet as the below warning log in kernel:
[ 0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV
[ 0.999196] LDO2: Bringing 800000uV into 900000-900000uV
Fixes: 78cc25fa265d ("arm64: dts: imx8mm-evk: Add BD71847 PMIC")
Cc: stable@vger.kernel.org
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu-core is supposed to list its supply separately, add
supply for secondary cpus.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-evk has a GPIO connected to AR8031 Ethernet PHY's reset pin.
Describe it in the device tree, following phy's datasheet reset duration of 10ms.
Tested booting via NFS.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Memory address/size depends on board design, so memory node should
be in board DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is used by the imx-ddrc devfreq driver to implement dynamic
frequency scaling of DRAM.
Support for proactive scaling via interconnect will come later. The
high-performance bus masters which need that (display, vpu, gpu) are
mostly not yet enabled in upstream anyway.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign clocks and clock-rates for audio plls, that audio
drivers can utilize them.
Add dai-tdm-slot-num and dai-tdm-slot-width for sound-wm8524,
that sai driver can generate correct bit clock.
Fixes: 13f3b9fdef6c ("arm64: dts: imx8mm-evk: Enable audio codec wm8524")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All these at803x properties are not documented anywhere, so
just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB1 port has typec connector with power delivery support:
- Dual data role: host and device.
- Dual power role: source and sink, prefer power sink.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has one wm8524 audio codec connected with
SAI3 digital audio interface.
This patch uses simple-card machine driver in order
to enable wm8524 codec.
We need to set:
* SAI3 pinctrl configuration
* codec reset gpio pinctrl configuration
* clock hierarchy
* codec node
* simple-card configuration
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The BUCK2 regulator is used for cpufreq voltage control, otherwise
configuration is mostly static.
This uses the newly-implemented rohm,reset-snvs-powered property to
properly handle the SNVS state of imx8mm.
Between BD71837 and BD71847 the BUCK3/4 regulators were removed but
datasheet and board schematics kept the names for BUCK5/6/7/8. The
driver however renumbered 5/6/7/8 to 3/4/5/6. Use the names from DT
bindings and add comments to signal this.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
