IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch adds support for the Azoteq IQS550/572/525 family of
trackpad/touchscreen controllers.
The driver has been tested with an IQS550EV02 evaluation board. A
demonstration of the driver's capabilities is available here:
https://youtu.be/sRNNx4XZBts
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GT5663 is capacitive touch controller with customized smart
wakeup gestures.
Add support for it by adding compatible and supported chip data.
The chip data on GT5663 is similar to GT1151, like
- config data register has 0x8050 address
- config data register max len is 240
- config data checksum has 16-bit
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix CTP controllers require AVDD28, VDDIO regulators for power-on
sequence.
The delay between these regualtor operations as per Power-on Timing
from datasheet[1] is 0 (T1 >= 0 usec).
So, enable and disable these regulators in proper order using normal
regulator functions without any delay in between.
[1] GT5663 Datasheet_English_20151106_Rev.01
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
When CONFIG_INPUT_POLLDEV is disabled, we get a link error:
drivers/input/touchscreen/raspberrypi-ts.o: In function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0xec): undefined reference to `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0xec): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0x19c): undefined reference to `input_register_polled_device'
raspberrypi-ts.c:(.text+0x19c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `input_register_polled_device'
Select that symbol like we do from the other similar drivers.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
While here, correct MODULE_LICENSE() string to be aligned with license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPI allows to enumerate specific devices by using compatible strings.
Enable that enumeration for EDT touchscreen devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_suspend':
drivers/input/touchscreen/ti_am335x_tsc.c:510:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_resume':
drivers/input/touchscreen/ti_am335x_tsc.c:527:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
It's not used any more after 333e07ec4b ("Input: ti_am335x_tsc: Mark TSC
device as wakeup source")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"Invalid config" gives little idea what's wrong. Print the values that
must not be 0 so we know which ones are off.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is required to specify generic touchscreen properties via DT.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_gpiod_get_optional() and gpiod_set_value_cansleep() instead
of the old API. The st1232_ts_power() now passes on the inverted "poweron"
value to reflect the correct logical value.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
work although the touch data contain such information.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is not a single user of the ili210x platform data in the kernel,
just drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should rely on the interrupt trigger (level vs edge) set up by the
firmware or board code instead of forcing what we consider appropriate.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some of the #defined register values are one-bit flags. Convert them to
use the BIT(x) macro instead of 1 byte hexadecimal values. This improves
readability and clarifies the intent.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
of_touchscreen.c provides a common interface for a axis inversion and
swapping of touchscreens. Therefore use it in the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 and sx8650 are quite similar, therefore add support for the
sx8650 within the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: use __be16 in sx8650_irq, add missing del_timer_sync]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the sx865[456] share the same datasheet and differ only in the
presence of a "capacitive proximity detection circuit" and a "haptics
motor driver for LRA/ERM" add them to the compatbiles. As the driver
doesn't implement these features it should be no problem.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 features a NRST input which may be connected to a GPIO.
Therefore add support for hard-resetting the sx8654 via this NRST.
If the reset-gpio property is provided the sx8654 is resetted via NRST
instead of the soft-reset via I2C.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds myself as an author of the st1232 driver module as Tony's
email address doesn't seem to work anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the Sitronix ST1633 touchscreen controller to the st1232
driver. A protocol spec can be found here:
www.ampdisplay.com/documents/pdf/AM-320480B6TZQW-TC0H.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
This patch removes common ADC settings in favor to use
stmpe811_adc_common_init that is present in MFD. This is necessary in
preparation for the stmpe-adc driver, because those two drivers have
common settings for the ADC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move defines that are ADC related to the header of the overlying MFD,
so they can be used from multiple sub-devices.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into for-linus
Sync with mainline to get linux/overflow.h among other things.
Fix link error when TOUCHSCREEN_RASPBERRYPI_FW is enabled as a module and
the dependent module is built-in. The 'depends on RASPBERRYPI_FIRMWARE' by
itself prevents the touchscreen driver from being built-in when the
firmware is configured as a module. However, the '|| COMPILE_TEST' still
allows it unless we explicitly prevent that configuration with
'|| (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)'.
ld: drivers/input/touchscreen/raspberrypi-ts.o: in function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0x3a8): undefined reference to `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x3a8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x4c8): undefined reference to `rpi_firmware_property'
ld: raspberrypi-ts.c:(.text+0x4c8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_property'
Rework so that TOUCHSCREEN_RASPBERRYPI_FW depends on
RASPBERRYPI_FIRMWARE=n if COMPILE_TEST is enabled.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately the evervision focaltech implementation uses two offset
registers, one for the x coordinate and one for y.
This patch extends the driver to handle those offset registers only for
devices that support these.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently only the threshold and gain parameters can be read.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Evervision displays are using different Focaltech touchscreen
controllers. This commit adds the initial support for the ones using the
FT5726 controller. Receiving the touch data is the same as for the
GENERIC_FT but the x and y cooridnates are swapped. The main differences
are the register addresses where the GAIN and THRESHOLD parameters are
stored.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into next
Merge with mainline to bring in the new APIs.
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
regmap_bulk_read() can return a non zero value on failure. The fix checks
if the function call succeeded before calling mod_timer. The issue was
identified by a static analysis tool.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A tiny pull request this merge window unfortunately, should get more
material in for the next release:
- new driver for Raspberry Pi's touchscreen (firmware interface)
- miscellaneous input driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G
Input: atmel_mxt_ts - don't try to free unallocated kernel memory
Input: drv2667 - fix indentation issues
Input: touchscreen - fix coding style issue
Input: add official Raspberry Pi's touchscreen driver
Input: nomadik-ske-keypad - fix a loop timeout test
Input: rotary-encoder - don't log EPROBE_DEFER to kernel log
Input: olpc_apsp - remove set but not used variable 'np'
Input: olpc_apsp - enable the SP clock
Input: olpc_apsp - check FIFO status on open(), not probe()
Input: olpc_apsp - drop CONFIG_OLPC dependency
clk: mmp2: add SP clock
dt-bindings: marvell,mmp2: Add clock id for the SP clock
Input: ad7879 - drop platform data support
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes the coding style problem reported
by checkpatch.pl as below:
ERROR: foo* bar should be "foo *bar"
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add's support to Raspberry Pi's 7" Touch device. Instead of using a
conventional bus all information is copied into a memory mapped area by
RPi's firmware.
Based on the driver found in RPi's kernel repository.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
This driver supports configuration via platform data but
absolutely nothing in the upstream kernel uses it. Since this
configuration allows harmful practices such as encoding the
GPIO base for the chip, delete platform data support so that
no new platform using it gets introduced.
Also: include the right driver header, not <linux/gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Loading then unloading wm97xx-ts.ko when CONFIG_AC97_BUS=m
causes a WARNING: from drivers/base/driver.c:
Unexpected driver unregister!
WARNING: CPU: 0 PID: 1709 at ../drivers/base/driver.c:193 driver_unregister+0x30/0x40
Fix this by only calling driver_unregister() with the same
condition that driver_register() is called.
Fixes: ae9d1b5fbd ("Input: wm97xx: add new AC97 bus support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchscreens, depending on the firmware and/or the digitizer, report
coordinates which never reach 0 along one or both of their axis.
This has been seen for example on the Silead touchscreens on a Onda V891w
and a Point of View mobii TAB-P800w(v2.0).
This commit adds support for touchscreen-min-x and touchscreen-min-y
device-properties which can be set to communicate the actual start
coordinates (rather then 0,0) to userspace.
This commit also drop the "(in pixels)" comment from the documentation
of the touchscreen-size-x and touchscreen-size-y properties. The comment
suggested that there is a relation between the range of reported
coordinates and the display resolution, which is only true for some
devices. The "(in pixels)" comment is replaced with "(maximum x coordinate
reported + 1)" to mirror the language describing the new touchscreen-min-x
and -min-y properties.
When set this fixes e.g. not being able to click things in the GNOME3
top-bar on the 2 example tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To avoid bounce buffer when an i2c controller decides to use DMA for a
transaction, let's make out buffer that we use for reads DMA-safe and let
the master know that DMAing into it is safe.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On AM335x, ti_am335x_tsc can wake up the system from suspend, mark the
IRQ as wakeup capable, so that device irq is not disabled during system
suspend.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of TSCADC MFD device, mark TSC as wakeup source and change all
wakeup related PM calls to operate on TSC device.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is how userspace checks for touchscreen devices most reliably.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry writes:
"Input updates for v4.19-rc5
Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - allow for max == min during input_absinfo validation
Input: elantech - enable middle button of touchpad on ThinkPad P72
Input: atakbd - fix Atari CapsLock behaviour
Input: atakbd - fix Atari keymap
Input: egalax_ts - add system wakeup support
Input: gpio-keys - fix a documentation index issue
Both v4.16-rc7 commit 93afb1d6e7 ("Input: atmel_mxt_ts - switch from
OF to generic device properties") and v4.16-rc7 commit 96a938aa21
("Input: atmel_mxt_ts - remove platform data support") added includes of
"<linux/property.h>". Remove one of the duplicate includes to fix this.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds wakeup function support for egalax touch
screen, if "wakeup-source" is added to device tree's egalax
touch screen node, the wakeup function will be enabled, and
egalax touch screen will be able to wakeup system from suspend.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If T9.CTRL DISAMP is set, then pressure is reported as zero. This means
some app layers (eg tslib) will ignore the contact.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use sscanf to parse the configuration file, so it's necessary to zero
terminate the configuration otherwise a truncated file can cause the
parser to run off into uninitialised memory.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On devices with the T71 object, the config CRC will start there, rather
than at T7.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wdt87xx_resume() is never called in atomic context. It calls mdelay() to
busily wait, which is not necessary. mdelay() can be replaced with
msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I do not think Vojtech wants snail mail these days (and he mentioned that
nobody has ever sent him snail mail), and the address is not even valid
anymore, so let's remove snail-mail instructions from the sources.
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Keep the documentation link up-to-date in case anybody need to dive into it
again, and update email address while at it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The only user of this driver in mainline does not make use of the module
parameters, so let's remove them. All properties for this driver should be
set through DT or pdata.
Use touchscreen_parse_properties() to automatically set some of the common
touchscreen properties and derive the axis inversion through that.
And finally, use touchscreen_report_pos() to handle the DT properties
automatically instead of doing the inversion ourselves.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide a match table so that the driver can be used in devicetree setups.
More properties are added in a later patch.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- the main change is a fix for my brain-dead patch to PS/2 button
reporting for some protocols that made it in 4.17
- there is a new driver for Spreadtum vibrator that I intended to send
during merge window but ended up not sending the 2nd pull request.
Given that this is a brand new driver we should not see regressions
here
- a fixup to Elantech PS/2 driver to avoid decoding errors on Thinkpad
P52
- addition of few more ACPI IDs for Silead and Elan drivers
- RMI4 is switched to using IRQ domain code instead of rolling its own
implementation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - fix button reporting for basic protocols
Input: xpad - fix GPD Win 2 controller name
Input: elan_i2c_smbus - fix more potential stack buffer overflows
Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID
Input: elantech - fix V4 report decoding for module with middle key
Input: elantech - enable middle button of touchpads on ThinkPad P52
Input: do not assign new tracking ID when changing tool type
Input: make input_report_slot_state() return boolean
Input: synaptics-rmi4 - fix axis-swap behavior
Input: synaptics-rmi4 - fix the error return code in rmi_probe_interrupts()
Input: synaptics-rmi4 - convert irq distribution to irq_domain
Input: silead - add MSSL0002 ACPI HID
Input: goldfish_events - fix checkpatch warnings
Input: add Spreadtrum vibrator driver
The usual mixed bunch. Particular good to see is the generic
touch screen driver. Will be interesting to see if this works
for other ADCs without major changes.
Core features
* Channel types
- New position relative channel type primarily for touch screen
sensors to feed the generic touchscreen driver.
New device support
* ad5586
- Add support for the AD5311R DAC.
* Generic touch screen driver as an IIO consumer.
- Note this is in input, but due to dependencies is coming through
the IIO tree.
- Specific support for this added to the at91-sama5d2 ADC.
- Various necessary DT bindings added.
Staging Drops
* ADIS16060 gyro
- A device with a very odd interface that was never cleanly supported.
It's now very difficult to get, so unlikely it'll ever be fixed up.
Cleanups and minor features and fixes
* core
- Fix y2038 timestamp issues now the core support is in place.
* 104-quad-8
- Provide some defines for magic numbers to help readability.
- Fix an off by one error in register selection
* ad7606
- Put in a missing function parameter name in a prototype.
* adis16023
- Use generic sign_extend function rather than local version.
* adis16240
- Use generic sign_extend funciton rather than local version.
* at91-sama5d2
- Drop dependency on HAS_DMA now this is handled elsewhere. Will
improve build test coverage.
- Add oversampling ratio control. Note there is a minor ABI change
here to increase the apparent depth to 14 bits so as to allow
for transparent provision of different oversampling ratios that
drop the actual bit depth to 13 or 12 bits.
* hx711
- Add a MAINTAINERS entry for this device.
* inv_mpu6050
- Replace the timestamp fifo 'special' code with generic timestamp
handling.
- Switch to using local store of timestamp divider rather than rate
as that is more helpful for accurate time measurement.
- Fix an unaligned access that didn't seem to be causing any trouble.
- Use the fifo overflow bit to track the overflow status rather than
a software counter.
- New timestamping mechanism to deal with missed sample interrupts.
* stm32-adc
- Drop HAS_DMA build dependency.
* sun4i-gpadc
- Select REGMAP_IRQ a very rarely hit build issue fix.
-----BEGIN PGP SIGNATURE-----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=SvKj
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, features and cleanups in the 4.19 cycle
The usual mixed bunch. Particular good to see is the generic
touch screen driver. Will be interesting to see if this works
for other ADCs without major changes.
Core features
* Channel types
- New position relative channel type primarily for touch screen
sensors to feed the generic touchscreen driver.
New device support
* ad5586
- Add support for the AD5311R DAC.
* Generic touch screen driver as an IIO consumer.
- Note this is in input, but due to dependencies is coming through
the IIO tree.
- Specific support for this added to the at91-sama5d2 ADC.
- Various necessary DT bindings added.
Staging Drops
* ADIS16060 gyro
- A device with a very odd interface that was never cleanly supported.
It's now very difficult to get, so unlikely it'll ever be fixed up.
Cleanups and minor features and fixes
* core
- Fix y2038 timestamp issues now the core support is in place.
* 104-quad-8
- Provide some defines for magic numbers to help readability.
- Fix an off by one error in register selection
* ad7606
- Put in a missing function parameter name in a prototype.
* adis16023
- Use generic sign_extend function rather than local version.
* adis16240
- Use generic sign_extend funciton rather than local version.
* at91-sama5d2
- Drop dependency on HAS_DMA now this is handled elsewhere. Will
improve build test coverage.
- Add oversampling ratio control. Note there is a minor ABI change
here to increase the apparent depth to 14 bits so as to allow
for transparent provision of different oversampling ratios that
drop the actual bit depth to 13 or 12 bits.
* hx711
- Add a MAINTAINERS entry for this device.
* inv_mpu6050
- Replace the timestamp fifo 'special' code with generic timestamp
handling.
- Switch to using local store of timestamp divider rather than rate
as that is more helpful for accurate time measurement.
- Fix an unaligned access that didn't seem to be causing any trouble.
- Use the fifo overflow bit to track the overflow status rather than
a software counter.
- New timestamping mechanism to deal with missed sample interrupts.
* stm32-adc
- Drop HAS_DMA build dependency.
* sun4i-gpadc
- Select REGMAP_IRQ a very rarely hit build issue fix.
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This adds a generic resistive touchscreen (GRTS) driver, which is based
on an IIO device (an ADC). It must be connected to the channels of an ADC
to receive touch data. Then it will feed the data into the input subsystem
where it registers an input device.
It uses an IIO callback buffer to register to the IIO device
Some parts of this patch are based on initial original work by
Mohamed Jamsheeth Hajanajubudeen and Bandaru Venkateswara Swamy
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Silead touchscreen on the Chuwi Vi8 tablet uses MSSL0002 as ACPI HID,
rather then the usual MSSL1680 id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp
Tested on a unit from the first production run sent to Indiegogo backers
Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Prevent system suspend while user has finger on touch screen,
because TSC is wakeup source and suspending device while in use will
result in failure to disable the module.
This patch uses pm_stay_awake() and pm_relax() APIs to prevent and
resume system suspend as required.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is seen that just enabling the TSC module triggers a HW_PEN IRQ
without any interaction with touchscreen by user. This results in first
suspend/resume sequence to fail as system immediately wakes up from
suspend as soon as HW_PEN IRQ is enabled in suspend handler due to the
pending IRQ. Therefore clear all IRQs at probe and also in suspend
callback for sanity.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At the mentioned address there's nothing found. By searching information
on the controller chip still can be found, so update the link to the
resulting page.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current reset-gpio support triggers an interrupt storm on platforms
using the maxtouch with level based interrupt. The Motorola Droid 4,
which I used for some of the tests is not affected, since it uses a edge
based interrupt.
This change avoids the interrupt storm by enabling the device while its
interrupt is disabled. Afterwards we wait 100ms. This is important for
two reasons: The device is unresponsive for some time (~22ms for
mxt224E) and the CHG (interrupt) line is not working properly for 100ms.
We don't need to wait for any following interrupts, since the following
mxt_initialize() checks for bootloader mode anyways.
This fixes a boot issue on GE PPD (watchdog kills device due to
interrupt storm) and does not cause regression on Motorola Droid 4.
Fixes: f657b00df2 ("Input: atmel_mxt_ts - add support for reset line")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver needs help determining whether it is dealing with a touchscreen
or a touchpad, and with button mapping. Previously we supported passing
this data via device properties, and also had DMI lists for Chromebooks
that specified Atmel devices in ACPI, but did not provide enough data
there. Now that chromeos_laptop driver is adjusted to supply necessary
device properties even for ACPI devices, we can drop the DMI tables and
refuse to probe if device properties are not attached to the device.
We use presence of "compatible" property to determine if device properties
are attached to the device or not and rely on chromeos_laptop to re-probe
the device after attaching missing device properties to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlsB91MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGqLYH+gPrmb8gvH6CmckN
5U+RKRjzvs6oDqXf5yFUJ7NqW1Ex8qMuAqv1Kx2LpuN8sDD42fPB0A5OxijNgk81
omJIxqANbFPUQCt+epR1P5dp0XqbXCcIvmo9Dd2TM4EP0mcQqr+c61d7JXtVATMu
JrR5X7pgepatgH7JYI7fm1yIh/6RIhYZXjU2HxwiRHIzsLfW/sTmM4HZksv8nJjl
m+bT8XzEUCBhWCLT8z0TbbVug1N2qdyMzkMIS2JmDVJE4FZ9YOEnZzaCHGNZrkVV
OYzr94Bv2Z2PO3KIrsEsNA/szhr9/8f5Si9mk9nOi2kTuvaF9hhjKxcCozVB+ses
fm8wpmM=
=FiAO
-----END PGP SIGNATURE-----
Merge tag 'v4.17-rc6' into next
Sync up with mainline to bring in Atmel controller changes for Caroline.
Allow querying of the firmware revision of the device
example:
4.10
Tested on ZII RDU2 platform and on Intel x86_64 PC.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChipOne icn8505 is an i2c capacitive touchscreen controller typically
used in cheap x86 tablets, this commit adds a driver for it.
Note the icn8505 is somewhat similar to the icn8318 and I started with
modifying that driver to support both, but in the end the differences were
too large and I decided to write a new driver instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - add missing compatible strings to OF device table
Input: atmel_mxt_ts - fix the firmware update
Input: atmel_mxt_ts - add touchpad button mapping for Samsung Chromebook Pro
MAINTAINERS: Rakesh Iyer can't be reached anymore
Input: hideep_ts - fix a typo in Kconfig
Input: alps - fix reporting pressure of v3 trackstick
Input: leds - fix out of bound access
Input: synaptics-rmi4 - fix an unchecked out of memory error path
Commit af503716ac ("i2c: core: report OF style module alias for devices
registered via OF") fixed how the I2C core reports the module alias when
devices are registered via OF.
But the atmel_mxt_ts driver only has an "atmel,maxtouch" compatible in its
OF device ID table, so if a Device Tree is using a different one, autoload
won't be working for the module (the matching works because the I2C device
ID table is used as a fallback).
So add compatible strings for each of the entries in the I2C device table.
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: document which compatibles are deprecated and should not be used]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The automatic update mechanism will trigger an update if the
info block CRCs are different between maxtouch configuration
file (maxtouch.cfg) and chip.
The driver compared the CRCs without retrieving the chip CRC,
resulting always in a failure and firmware flashing action
triggered. Fix this issue by retrieving the chip info block
CRC before the check.
Note that this solution has the benefit that by reading the
information block and the object table into a contiguous region
of memory, we can verify the checksum at probe time. This means
we make sure that we are indeed talking to a chip that supports
object protocol correctly.
Using this patch on a kevin chromebook, the touchscreen and
touchpad drivers are able to match the CRC:
atmel_mxt_ts 3-004b: Family: 164 Variant: 14 Firmware V2.3.AA Objects: 40
atmel_mxt_ts 5-004a: Family: 164 Variant: 17 Firmware V2.0.AA Objects: 31
atmel_mxt_ts 3-004b: Resetting device
atmel_mxt_ts 5-004a: Resetting device
atmel_mxt_ts 3-004b: Config CRC 0x573E89: OK
atmel_mxt_ts 3-004b: Touchscreen size X4095Y2729
input: Atmel maXTouch Touchscreen as /devices/platform/ff130000.i2c/i2c-3/3-004b/input/input5
atmel_mxt_ts 5-004a: Config CRC 0x0AF6BA: OK
atmel_mxt_ts 5-004a: Touchscreen size X1920Y1080
input: Atmel maXTouch Touchpad as /devices/platform/ff140000.i2c/i2c-5/5-004a/input/input6
Signed-off-by: Nick Dyer <nick.dyer@shmanahar.org>
Acked-by: Benson Leung <bleung@chromium.org>
[Ezequiel: minor patch massage]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a spelling error found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Incorporates a series from Dmitry to remove platform data from
chromeos_laptop.c, which was the only user of platform data
for the atmel_mxt_ts driver.
Includes a series to clean up sysfs and debugfs for cros_ec.
Other misc. cleanups.
Thanks,
Benson
-----BEGIN PGP SIGNATURE-----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=mDkk
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
Now that there are no users of custom Atmel platform data, and everyone
has switched to the generic device properties, we can remove support for
the platform data.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Move older ChromeOS devices describing Atmel controllers in ACPI, but not
providing enough details to configure the controllers properly, from
platform data over to generic device properties. This will allow us
remove support for platform data later on, leaving only generic device
properties in place.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of using OF-specific APIs to fecth device properties, let's switch
to generic device properties API. This will allow us to use device
properties on legacy ChromeOS devices and get rid of platform data down
the road.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
The way we are supposed to put controller to sleep and wake it up does not
depend on the platform, but rather on controller itself, so we want to get
rid of suspend mode in platform data (and eventually get rid of platform
data completely). Unfortunately some early chromebooks (the original Pixel,
Acer C720) were shipped with config that requires manually re-enabling
touch reporting in T9. We will sort it out, but in the meantime let's
switch to a simple DMI quirk.
We'll keep pdata->suspend_mode for now and remove it when we rework
chromeos-laptop driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull input updates from Dmitry Torokhov:
- new driver for PhoenixRC Flight Controller Adapter
- new driver for RAVE SP Power button
- fixes for autosuspend-related deadlocks in a few unput USB dirvers
- support for 2nd wheel in ATech PS/2 mouse
- fix for ALPS trackpoint detection on Thinkpad L570 and Latitude 7370
- bunch of cleanups in various in PS/2 protocols
- other assorted changes and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad
Input: stmfts, s6sy761 - update my e-mail
Input: stmfts - use async probe & suspend/resume to avoid 2s delay
Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370
Input: xpad - add PDP device id 0x02a4
Input: alps - report pressure of v3 and v7 trackstick
Input: pxrc - new driver for PhoenixRC Flight Controller Adapter
Input: usbtouchscreen - do not rely on input_dev->users
Input: usbtouchscreen - fix deadlock in autosuspend
Input: pegasus_notetaker - do not rely on input_dev->users
Input: pagasus_notetaker - fix deadlock in autosuspend
Input: synaptics_usb - do not rely on input_dev->users
Input: synaptics_usb - fix deadlock in autosuspend
Input: gpio-keys - add support for wakeup event action
Input: appletouch - use true and false for boolean values
Input: silead - add Chuwi Hi8 support
Input: analog - use get_cycles() on PPC
Input: stmpe-keypad - remove VLA usage
Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list
Input: add RAVE SP Powerbutton driver
...
-----BEGIN PGP SIGNATURE-----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=bzhS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
Because I will be leaving Samsung soon, for reachability update
my reference e-mail to etezian.org.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Executing stmfts_power_on() function lasts over 2 seconds, what
significantly slows down the boot and resume processes if driver is
compiled in. Avoid this delay by forcing this driver to be probed
and suspended/resumed asynchronously.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is unused and suspended, a call to open will cause the
device to autoresume through the call to usb_autopm_get_interface().
input_dev->users is already incremented by the input subsystem,
therefore this expression will always be evaluated to true:
if (input->users || usbtouch->type->irq_always)
result = usb_submit_urb(usbtouch->irq, GFP_NOIO);
The same URB will then be fail when resubmitted in usbtouch_open().
Introduce usbtouch->is_open to keep track of the state instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_autopm_get_interface() that is called in usbtouch_open() does an
autoresume if the device is suspended.
input_dev->mutex used in usbtouch_resume() is in this case already
taken by the input subsystem and will cause a deadlock.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit add ACPI support for Chuwi Hi8 tablet. On the ACPI table of
the tablet, GSL1680 is registered as MSSL0001, so the driver does not
recognize the device. This commit resolve it.
Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- we are reverting patch that was switched touchpad on Lenovo T460P
over to native RMI because on these boxes BIOS messes up with SMBus
controller state. We might re-enable it later once SMBus issue is
resolved
- disabling interrupts in matrix_keypad driver was racy
- mms114 now has SPDX header and matching MODULE_LICENSE
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - Lenovo Thinkpad T460p devices should use RMI"
Input: matrix_keypad - fix race when disabling interrupts
Input: mms114 - add SPDX identifier
Input: mms114 - fix license module information
This patch registers four standard control handlers using the corresponding
V4L2 framework.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
[hans.verkuil@cisco.com: lower-cased 0x0F and 0xF0]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These functions provide write access to the internal LCD panel registers
which also control the sensor. They can be used to disable the
preprocessor, set the illumination brightness, and adjust gain/contrast
(which are stored together in one register internally called "vsvideo").
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds parameter definitions and module parameters for the four
userspace controls that the SUR40 can currently provide.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The SUR40 can recognize specific printed patterns directly in hardware;
this information (i.e. the pattern id) is present but currently unused
in the blob structure.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the original license statement with the SPDX identifier.
Add also one line of description as recommended by the COPYING
file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver has been released with GNU Public License v2 as stated
in the header, but the module license information has been tagged
as "GPL" (GNU Public License v2 or later).
Fix the module license information so that it matches the one in
the header as "GPL v2".
Fixes: 07b8481d4a ("Input: add MELFAS mms114 touchscreen driver")
Reported-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer updates from Dmitry Torokhov:
- evdev interface has been adjusted to extend the life of timestamps on
32 bit systems to the year of 2108
- Synaptics RMI4 driver's PS/2 guest handling ha beed updated to
improve chances of detecting trackpoints on the pass-through port
- mms114 touchcsreen controller driver has been updated to support
generic device properties and work with mms152 cntrollers
- Goodix driver now supports generic touchscreen properties
- couple of drivers for AVR32 architecture are gone as the architecture
support has been removed from the kernel
- gpio-tilt driver has been removed as there are no mainline users and
the driver itself is using legacy APIs and relies on platform data
- MODULE_LINECSE/MODULE_VERSION cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: goodix - use generic touchscreen_properties
Input: mms114 - fix typo in definition
Input: mms114 - use BIT() macro instead of explicit shifting
Input: mms114 - replace mdelay with msleep
Input: mms114 - add support for mms152
Input: mms114 - drop platform data and use generic APIs
Input: mms114 - mark as direct input device
Input: mms114 - do not clobber interrupt trigger
Input: edt-ft5x06 - fix error handling for factory mode on non-M06
Input: stmfts - set IRQ_NOAUTOEN to the irq flag
Input: auo-pixcir-ts - delete an unnecessary return statement
Input: auo-pixcir-ts - remove custom log for a failed memory allocation
Input: da9052_tsi - remove unused mutex
Input: docs - use PROPERTY_ENTRY_U32() directly
Input: synaptics-rmi4 - log when we create a guest serio port
Input: synaptics-rmi4 - unmask F03 interrupts when port is opened
Input: synaptics-rmi4 - do not delete interrupt memory too early
Input: ad7877 - use managed resource allocations
Input: stmfts,s6sy671 - add SPDX identifier
Input: remove atmel-wm97xx touchscreen driver
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Use touchscreen_properties structure instead of implementing all
properties by our own. It allows us to reuse generic code for parsing
device-tree properties (which was implemented manually in the driver for
now). Additionally, it allows us to report events using generic
touchscreen_report_pos(), which automatically handles inverted and
swapped axes.
This fixes the issue with the custom code incorrectly handling case where
ts->inverted_x and ts->swapped_x_y were true, but ts->inverted_y was
false. Assuming we have 720x1280 touch panel, ts->abs_x_max == 1279 and
ts->abs_y_max == 719 (because we inverted that in goodix_read_config()).
Now let's assume that we received event from (0:0) position (in touch
panel original coordinates). In function goodix_ts_report_touch() we
calculate input_x as 1279, but after swapping input_y takes that value
(which is more that maximum 719 value reported during initialization).
Note that since touchscreen coordinates are 0-indexed, we now report
touchscreen range as (0:size-1).
Developed and tested on custom DT-based device with gt1151 touch
panel.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
[dtor: fix endianness annotation reported by sparse, handle errors when
initializing MT slots]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
200 milliseconds is a very long time to keep the CPU busy looping.
Use msleep instead.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS152 has no configuration registers, but the packet format used in
interrupts is identical to mms114.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MMS114 platform data has no in-tree users, so drop it.
Switch to using the standard touchscreen properties via
touchscreen_parse_properties(), and move the old DT parsing code
to use device_property_*() APIs.
Finally, use touchscreen_report_pos to report x/y coordinates
and drop the custom x/y inversion code.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
mms14 is a touchscreen and thus a direct input device; let's mark it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Also add error handling for input_mt_init_slots().
Reviewed-by: Simon Shields <simon@lineageos.org>
Tested-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"The main item is that we try to better handle the newer trackpoints on
Lenovo devices that are now being produced by Elan/ALPS/NXP and only
implement a small subset of the original IBM trackpoint controls"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics_rmi4 - use devm_device_add_group() for attributes in F01"
Input: trackpoint - only expose supported controls for Elan, ALPS and NXP
Input: trackpoint - force 3 buttons if 0 button is reported
Input: xpad - add support for PDP Xbox One controllers
Input: stmfts,s6sy671 - add SPDX identifier
When attempting enter factory mode on firmware that does not support it,
we'd error out, but leave the device with interrupts disabled, and thus
touch not working. Fix it by moving the check before we disable
interrupts/allocate memory for debug buffers.
Fixes: fd335ab04b ("Input: edt-ft5x06 - add support for M09 firmware version")
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The interrupt is requested before the device is powered on and
it's value in some cases cannot be reliable. It happens on some
devices that an interrupt is generated as soon as requested
before having the chance to disable the irq.
Set the irq flag as IRQ_NOAUTOEN before requesting it.
This patch mutes the error:
stmfts 2-0049: failed to read events: -11
received sometimes during boot time.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
