IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
- Disable use of D3cold on Asus B1400 PCI-NVMe bridges because some BIOSes
can't power them back on, replacing a more general ACPI sleep quirk
(Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any runtime
PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races between
.remove() and .runtime_idle(), which caused intermittent page faults when
the rtsx .runtime_idle() accessed registers that its .remove() had
already unmapped (Rafael J. Wysocki)
* pci/pm:
PCI/PM: Drain runtime-idle callbacks before driver removal
PCI/PM: Allow runtime PM with no PM callbacks at all
Revert "ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default"
PCI: Disable D3cold on Asus B1400 PCI-NVMe bridge
- Collect interrupt-related code in irq.c (Ilpo Järvinen)
- Mark 3ware-9650SE Root Port Extended Tags as broken (Jörg Wedekind)
* pci/enumeration:
PCI: Mark 3ware-9650SE Root Port Extended Tags as broken
PCI: Place interrupt related code into irq.c
# Conflicts:
# drivers/pci/Makefile
- After a DPC event, print all logged TLP Prefixes instead of printing the
first prefix several times (Ilpo Järvinen)
- Ignore the expected Surprise Down error that may cause a DPC event when
hot-removing a device (Smita Koralahalli)
- Add an RP PIO log size quirk for Intel Raptor Lake Root Ports, which
still don't advertise the correct log size, which prevented logging of RP
PIO Log registers when DPC is triggered (Paul Menzel)
* pci/dpc:
PCI/DPC: Quirk PIO log size for Intel Raptor Lake Root Ports
PCI/DPC: Ignore Surprise Down error on hot removal
PCI/DPC: Print all TLP Prefixes, not just the first
- Unmap MMIO mappings in pci_iounmap() to avoid a leak when
ARCH_HAS_GENERIC_IOPORT_MAP is defined (Philipp Stanner)
- Move pci_iomap.c to drivers/pci/ since it's all PCI-related (Philipp
Stanner)
- Move other PCI-related devres code from lib/devres.c to drivers/pci/
(Philipp Stanner)
- Move other devres code from pci.c to devres.c (Philipp Stanner)
* pci/devres:
PCI: Move devres code from pci.c to devres.c
PCI: Move PCI-specific devres code to drivers/pci/
PCI: Move pci_iomap.c to drivers/pci/
pci_iounmap(): Fix MMIO mapping leak
- Collect ASPM-related code into aspm.c (David E. Box)
- Save and restore ASPM L1 PM Substates configuration so these states
continue working after suspend/resume (David E. Box)
- Move the ASPM L1.2-related LTR save/restore next to the ASPM save/restore
(David E. Box)
- Move the required L1 disable before L1 Substate configuration into
pci_restore_aspm_l1ss_state() (Bjorn Helgaas)
- Update save_save when ASPM config is changed, so a .slot_reset() during
error recovery restores the changed config, not the .probe()-time config
(Vidya Sagar)
* pci/aspm:
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
PCI/ASPM: Move pci_configure_ltr() to aspm.c
Many PCIe device drivers save the configuration state of their device
during probe and restore it when their .slot_reset() hook is called during
PCIe error recovery.
If the ASPM configuration is changed after the driver's probe is called and
before an error event occurs, .slot_reset() restores the ASPM configuration
to what it was at the time of probe, not to what it was just before the
occurrence of the error event. This leads to a mismatch in ASPM
configuration between the device and its upstream device.
Update the saved configuration of the device when the ASPM configuration
changes.
Link: https://lore.kernel.org/r/20240222174436.3565146-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[bhelgaas: commit log, rebase to pci/aspm, rename to
pci_update_aspm_saved_state() since it updates only LNKCTL, update only
ASPMC and CLKREQ_EN in LNKCTL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Per PCIe r6.1, sec 5.5.4, L1 must be disabled while setting ASPM L1 PM
Substates enable bits. Previously this was enforced by clearing
PCI_EXP_LNKCTL_ASPMC before calling pci_restore_aspm_l1ss_state().
Move the L1 (and L0s, although that doesn't seem required) disable into
pci_restore_aspm_l1ss_state() itself so it's closer to the code that
depends on it.
Link: https://lore.kernel.org/r/20240223213733.GA115410@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
4ff116d0d5fd ("PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume") restored the L1 PM Substates Capability after resume,
which reduced power consumption by making the ASPM L1.x states work after
resume.
a7152be79b62 ("Revert "PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume"") reverted 4ff116d0d5fd because resume failed on some
systems, so power consumption after resume increased again.
a7152be79b62 mentioned that we restore L1 PM substate configuration even
though ASPM L1 may already be enabled. This is due the fact that the
pci_restore_aspm_l1ss_state() was called before pci_restore_pcie_state().
Save and restore the L1 PM Substates Capability, following PCIe r6.1, sec
5.5.4 more closely by:
1) Do not restore ASPM configuration in pci_restore_pcie_state() but
do that after PCIe capability is restored in pci_restore_aspm_state()
following PCIe r6.1, sec 5.5.4.
2) If BIOS reenables L1SS, particularly L1.2, we need to clear the
enables in the right order, downstream before upstream. Defer
restoring the L1SS config until we are at the downstream component.
Then update the config for both ends of the link in the prescribed
order.
3) Program ASPM L1 PM substate configuration before L1 enables.
4) Program ASPM L1 PM substate enables last, after rest of the fields
in the capability are programmed.
[bhelgaas: commit log, squash L1SS-related patches, do both LNKCTL restores
in pci_restore_pcie_state()]
Link: https://lore.kernel.org/r/20240128233212.1139663-3-david.e.box@linux.intel.com
Link: https://lore.kernel.org/r/20240128233212.1139663-4-david.e.box@linux.intel.com
Link: https://lore.kernel.org/r/20240223205851.114931-5-helgaas@kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217321
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216782
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216877
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Co-developed-by: David E. Box <david.e.box@linux.intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Tasev Nikola <tasev.stefanoska@skynet.be> # Asus UX305FA
Cc: Mark Enriquez <enriquezmark36@gmail.com>
Cc: Thomas Witt <kernel@witt.link>
Cc: Werner Sembach <wse@tuxedocomputers.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Both AER and DPC RP PIO provide TLP Header Log registers (PCIe r6.1 secs
7.8.4 & 7.9.14) to convey error diagnostics but the struct is named after
AER as the struct aer_header_log_regs. Also, not all places that handle TLP
Header Log use the struct and the struct members are named individually.
Generalize the struct name and members, and use it consistently where TLP
Header Log is being handled so that a pcie_read_tlp_log() helper can be
easily added.
Link: https://lore.kernel.org/r/20240206135717.8565-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: drop ixgbe changes for now, tidy whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use u32 for PCIe AER Capability register variable and name it "aercc"
(Advanced Error Capabilities and Control register, PCIe r6.1 sec 7.8.4.7)
instead of "temp".
Link: https://lore.kernel.org/r/20240206135717.8565-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: make subject more specific and match similar previous patches]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PM runtime can be done simultaneously with AER error handling. Avoid that
by using pm_runtime_get_sync() before and pm_runtime_put() after reset in
pcie_do_recovery() for all recovering devices.
pm_runtime_get_sync() will increase dev->power.usage_count counter to
prevent any possible future request to runtime suspend a device. It will
also resume a device, if it was previously in D3hot state.
I tested with igc device by doing simultaneous aer_inject and rpm
suspend/resume via /sys/bus/pci/devices/PCI_ID/power/control and can
reproduce:
igc 0000:02:00.0: not ready 65535ms after bus reset; giving up
pcieport 0000:00:1c.2: AER: Root Port link has been reset (-25)
pcieport 0000:00:1c.2: AER: subordinate device reset failed
pcieport 0000:00:1c.2: AER: device recovery failed
igc 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
The problem disappears when this patch is applied.
Link: https://lore.kernel.org/r/20240212120135.146068-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: <stable@vger.kernel.org>
Even when CONFIG_PCIEASPM is not set, we save and restore the LTR
Capability so that if ASPM L1.2 and LTR were configured by the platform,
ASPM L1.2 will still work after suspend/resume, when that platform
configuration may be lost. See dbbfadf23190 ("PCI/ASPM: Save LTR Capability
for suspend/resume").
Since ASPM L1.2 depends on the LTR Capability, move the save/restore code
to the part of aspm.c that is always compiled regardless of
CONFIG_PCIEASPM. No functional change intended.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20240128233212.1139663-5-david.e.box@linux.intel.com
[bhelgaas: commit log, reorder to make this a pure move]
Link: https://lore.kernel.org/r/20240223205851.114931-4-helgaas@kernel.org
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Latency Tolerance Reporting (LTR) mechanism supports the ASPM L1.2
state and is only configured when CONFIG_PCIEASPM is set.
Move pci_configure_ltr() and pci_bridge_reconfigure_ltr() into aspm.c since
they only build when CONFIG_PCIEASPM is set. No functional change
intended.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20240128233212.1139663-2-david.e.box@linux.intel.com
[bhelgaas: commit log, split build change from function moves]
Link: https://lore.kernel.org/r/20240223205851.114931-2-helgaas@kernel.org
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 5459c0b70467 ("PCI/DPC: Quirk PIO log size for certain Intel Root
Ports") and commit 3b8803494a06 ("PCI/DPC: Quirk PIO log size for Intel Ice
Lake Root Ports") add quirks for Ice, Tiger and Alder Lake Root Ports.
System firmware for Raptor Lake still has the bug, so Linux logs the
warning below on several Raptor Lake systems like Dell Precision 3581 with
Intel Raptor Lake processor (0W18NX) system firmware/BIOS version 1.10.1.
pci 0000:00:07.0: [8086:a76e] type 01 class 0x060400
pci 0000:00:07.0: DPC: RP PIO log size 0 is invalid
pci 0000:00:07.1: [8086:a73f] type 01 class 0x060400
pci 0000:00:07.1: DPC: RP PIO log size 0 is invalid
Apply the quirk for Raptor Lake Root Ports as well.
This also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Link: https://lore.kernel.org/r/20240305113057.56468-1-pmenzel@molgen.mpg.de
Reported-by: Niels van Aert <nvaert1986@hotmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218560
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Niels van Aert <nvaert1986@hotmail.com>
A race condition between the .runtime_idle() callback and the .remove()
callback in the rtsx_pcr PCI driver leads to a kernel crash due to an
unhandled page fault [1].
The problem is that rtsx_pci_runtime_idle() is not expected to be running
after pm_runtime_get_sync() has been called, but the latter doesn't really
guarantee that. It only guarantees that the suspend and resume callbacks
will not be running when it returns.
However, if a .runtime_idle() callback is already running when
pm_runtime_get_sync() is called, the latter will notice that the runtime PM
status of the device is RPM_ACTIVE and it will return right away without
waiting for the former to complete. In fact, it cannot wait for
.runtime_idle() to complete because it may be called from that callback (it
arguably does not make much sense to do that, but it is not strictly
prohibited).
Thus in general, whoever is providing a .runtime_idle() callback needs
to protect it from running in parallel with whatever code runs after
pm_runtime_get_sync(). [Note that .runtime_idle() will not start after
pm_runtime_get_sync() has returned, but it may continue running then if it
has started earlier.]
One way to address that race condition is to call pm_runtime_barrier()
after pm_runtime_get_sync() (not before it, because a nonzero value of the
runtime PM usage counter is necessary to prevent runtime PM callbacks from
being invoked) to wait for the .runtime_idle() callback to complete should
it be running at that point. A suitable place for doing that is in
pci_device_remove() which calls pm_runtime_get_sync() before removing the
driver, so it may as well call pm_runtime_barrier() subsequently, which
will prevent the race in question from occurring, not just in the rtsx_pcr
driver, but in any PCI drivers providing .runtime_idle() callbacks.
Link: https://lore.kernel.org/lkml/20240229062201.49500-1-kai.heng.feng@canonical.com/ # [1]
Link: https://lore.kernel.org/r/5761426.DvuYhMxLoT@kreacher
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ricky Wu <ricky_wu@realtek.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Commit c5eb1190074c ("PCI / PM: Allow runtime PM without callback
functions") eliminated the need for PM callbacks in
pci_pm_runtime_suspend() and pci_pm_runtime_resume(), but
didn't do the same for pci_pm_runtime_idle().
Therefore, runtime suspend worked as long as the driver implemented at
least one PM callback. But if the driver doesn't implement any PM
callbacks at all (driver->pm is NULL), pci_pm_runtime_idle() returned
-ENOSYS, which prevented runtime suspend.
Modify pci_pm_runtime_idle() to allow PCI device power state transitions
without runtime PM callbacks and complete the original intention of commit
c5eb1190074c ("PCI / PM: Allow runtime PM without callback functions").
Link: https://lore.kernel.org/r/20240227062648.16579-1-raag.jadav@intel.com
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
According to PCIe r6.0 sec 6.7.6 [1], async removal with DPC may result in
surprise down error. This error is expected and is just a side-effect of
async remove.
Ignore surprise down error generated as a side-effect of async remove.
Typically, this error is benign as the pciehp handler invoked by PDC
or/and DLLSC alongside DPC, de-enumerates and brings down the device
appropriately, but the error messages might confuse users. Get rid of
these irritating log messages with a 1s delay while pciehp waits for
DPC recovery.
The implementation is as follows: On an async remove a DPC is triggered
along with a Presence Detect State change and/or DLL State Change.
Determine it's an async remove by checking for DPC Trigger Status in DPC
Status Register and Surprise Down Error Status in AER Uncorrected Error
Status to be non-zero. If true, treat the DPC event as a side-effect of
async remove, clear the error status registers and continue with hot-plug
tear down routines. If not, follow the existing routine to handle AER and
DPC errors.
Masking Surprise Down Errors was explored as an alternative approach, but
discarded due to the odd behavior that masking only avoids the interrupt,
but still records an error per PCIe r6.0, sec 6.2.3.2.2. That stale error
would be reported the next time some error other than Surprise Down is
handled.
Dmesg before:
pcieport 0000:00:01.4: DPC: containment event, status:0x1f01 source:0x0000
pcieport 0000:00:01.4: DPC: unmasked uncorrectable error detected
pcieport 0000:00:01.4: PCIe Bus Error: severity=Uncorrected (Fatal), type=Transaction Layer, (Receiver ID)
pcieport 0000:00:01.4: device [1022:14ab] error status/mask=00000020/04004000
pcieport 0000:00:01.4: [ 5] SDES (First)
nvme nvme2: frozen state error detected, reset controller
pcieport 0000:00:01.4: DPC: Data Link Layer Link Active not set in 1000 msec
pcieport 0000:00:01.4: AER: subordinate device reset failed
pcieport 0000:00:01.4: AER: device recovery failed
pcieport 0000:00:01.4: pciehp: Slot(16): Link Down
nvme2n1: detected capacity change from 1953525168 to 0
pci 0000:04:00.0: Removing from iommu group 49
Dmesg after:
pcieport 0000:00:01.4: pciehp: Slot(16): Link Down
nvme1n1: detected capacity change from 1953525168 to 0
pci 0000:04:00.0: Removing from iommu group 37
[1] PCI Express Base Specification Revision 6.0, Dec 16 2021.
https://members.pcisig.com/wg/PCI-SIG/document/16609
Link: https://lore.kernel.org/r/20240207181854.121335-1-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
This fixes PCI Parity Errors like :
3w-9xxx: scsi0: ERROR: (0x06:0x000C): PCI Parity Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000E): Controller Queue Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x0010): Microcontroller Error: clearing.
Link: https://lore.kernel.org/r/20240219132811.8351-1-joerg@wedekind.de
Fixes: 60db3a4d8cc9 ("PCI: Enable PCIe Extended Tags if supported")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=202425
Signed-off-by: Jörg Wedekind <joerg@wedekind.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The file pci.c is very large and contains a number of devres functions.
These functions should now reside in devres.c.
Move as much devres-specific code from pci.c to devres.c as possible.
There are a few callers left in pci.c that do devres operations. These
should be ported in the future. Add corresponding TODOs.
The reason they are not moved right now in this commit is that PCI's devres
currently implements a sort of "hybrid-mode": pci_request_region(), for
instance, does not have a corresponding pcim_ equivalent, yet. Instead, the
function can be made managed by previously calling pcim_enable_device()
(instead of pci_enable_device()). This makes it unreasonable to move
pci_request_region() to devres.c. Moving the functions would require
changes to PCI's API and is, therefore, left for future work.
In summary, this commit serves as a preparation step for a following
patch series that will cleanly separate the PCI's managed and unmanaged
API.
Link: https://lore.kernel.org/r/20240131090023.12331-5-pstanner@redhat.com
Suggested-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pcim_*() functions in lib/devres.c are guarded by an #ifdef CONFIG_PCI
and, thus, don't belong to this file. They are only ever used for PCI and
are not generic infrastructure.
Move all pcim_*() functions in lib/devres.c to drivers/pci/devres.c.
Adjust the Makefile.
Add drivers/pci/devres.c to Documentation.
Link: https://lore.kernel.org/r/20240131090023.12331-4-pstanner@redhat.com
Suggested-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The entirety of pci_iomap.c is guarded by an #ifdef CONFIG_PCI. It,
consequently, does not belong to lib/ because it is not generic
infrastructure.
Move pci_iomap.c to drivers/pci/ and implement the necessary changes to
Makefiles and Kconfigs.
Update MAINTAINERS file.
Update Documentation.
Link: https://lore.kernel.org/r/20240131090023.12331-3-pstanner@redhat.com
[bhelgaas: squash in https://lore.kernel.org/r/20240212150934.24559-1-pstanner@redhat.com]
Suggested-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
It is not allowed to sleep within a RCU read section, so use GFP_ATOMIC
instead of GFP_KERNEL here.
Link: https://lore.kernel.org/r/02d9ec4a10235def0e764ff1f5be881ba12e16e8.1704397858.git.christophe.jaillet@wanadoo.fr
Fixes: ae21f835a5bd ("PCI/P2PDMA: Finish RCU conversion of pdev->p2pdma")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Fixes: f20c4ea49ec4 ("PCI/DPC: Add eDPC support")
Link: https://lore.kernel.org/r/20240118110815.3867-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: add user-visible details to commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add support for parsing the Coherent Device Attribute Table (CDAT)
- Add support for calculating a platform CXL QoS class from CDAT data
- Unify the tracing of EFI CXL Events with native CXL Events.
- Add Get Timestamp support
- Miscellaneous cleanups and fixups
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCZaHVvAAKCRDfioYZHlFs
Z3sCAQDPHSsHmj845k4lvKbWjys3eh78MKKEFyTXLQgYhOlsGAEAigQY2ZiSum52
nwdIgpOOADNt0Iq6yXuLsmn9xvY9bAU=
=HjCl
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL (Compute Express Link) updates from Dan Williams:
"The bulk of this update is support for enumerating the performance
capabilities of CXL memory targets and connecting that to a platform
CXL memory QoS class. Some follow-on work remains to hook up this data
into core-mm policy, but that is saved for v6.9.
The next significant update is unifying how CXL event records (things
like background scrub errors) are processed between so called
"firmware first" and native error record retrieval. The CXL driver
handler that processes the record retrieved from the device mailbox is
now the handler for that same record format coming from an EFI/ACPI
notification source.
This also contains miscellaneous feature updates, like Get Timestamp,
and other fixups.
Summary:
- Add support for parsing the Coherent Device Attribute Table (CDAT)
- Add support for calculating a platform CXL QoS class from CDAT data
- Unify the tracing of EFI CXL Events with native CXL Events.
- Add Get Timestamp support
- Miscellaneous cleanups and fixups"
* tag 'cxl-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (41 commits)
cxl/core: use sysfs_emit() for attr's _show()
cxl/pci: Register for and process CPER events
PCI: Introduce cleanup helpers for device reference counts and locks
acpi/ghes: Process CXL Component Events
cxl/events: Create a CXL event union
cxl/events: Separate UUID from event structures
cxl/events: Remove passing a UUID to known event traces
cxl/events: Create common event UUID defines
cxl/events: Promote CXL event structures to a core header
cxl: Refactor to use __free() for cxl_root allocation in cxl_endpoint_port_probe()
cxl: Refactor to use __free() for cxl_root allocation in cxl_find_nvdimm_bridge()
cxl: Fix device reference leak in cxl_port_perf_data_calculate()
cxl: Convert find_cxl_root() to return a 'struct cxl_root *'
cxl: Introduce put_cxl_root() helper
cxl/port: Fix missing target list lock
cxl/port: Fix decoder initialization when nr_targets > interleave_ways
cxl/region: fix x9 interleave typo
cxl/trace: Pass UUID explicitly to event traces
cxl/region: use %pap format to print resource_size_t
cxl/region: Add dev_dbg() detail on failure to allocate HPA space
...
Here is the big set of char/misc and other driver subsystem changes for
6.8-rc1. Lots of stuff in here, but first off, you will get a merge
conflict in drivers/android/binder_alloc.c when merging this tree due to
changing coming in through the -mm tree.
The resolution of the merge issue can be found here:
https://lore.kernel.org/r/20231207134213.25631ae9@canb.auug.org.au
or in a simpler patch form in that thread:
https://lore.kernel.org/r/ZXHzooF07LfQQYiE@google.com
If there are issues with the merge of this file, please let me know.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported issues
(other than the binder merge conflict.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeMMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynWNgCfQ/Yz7QO6EMLDwHO5LRsb3YMhjL4AoNVdanjP
YoI7f1I4GBcC0GKNfK6s
=+Kyv
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem changes
for 6.8-rc1.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (341 commits)
android: removed duplicate linux/errno
uio: Fix use-after-free in uio_open
drivers: soc: xilinx: add check for platform
firmware: xilinx: Export function to use in other module
scripts/tags.sh: remove find_sources
scripts/tags.sh: use -n to test archinclude
scripts/tags.sh: add local annotation
scripts/tags.sh: use more portable -path instead of -wholename
scripts/tags.sh: Update comment (addition of gtags)
firmware: zynqmp: Convert to platform remove callback returning void
firmware: turris-mox-rwtm: Convert to platform remove callback returning void
firmware: stratix10-svc: Convert to platform remove callback returning void
firmware: stratix10-rsu: Convert to platform remove callback returning void
firmware: raspberrypi: Convert to platform remove callback returning void
firmware: qemu_fw_cfg: Convert to platform remove callback returning void
firmware: mtk-adsp-ipc: Convert to platform remove callback returning void
firmware: imx-dsp: Convert to platform remove callback returning void
firmware: coreboot_table: Convert to platform remove callback returning void
firmware: arm_scpi: Convert to platform remove callback returning void
firmware: arm_scmi: Convert to platform remove callback returning void
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmWldYsUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyxUhAAs2ctoK/sMAfTOO2b1UAD/ig7CGGz
DlDt38RezFU4uqeY0Ix4heFs3RIt8YGuns76Fejfyevh1I7SOA9lbhFuMLBfO9j0
LU+KuZeGoXtIe5Kd6hCQIUgVvwISs407yp7JUUzqxFQ2rv7bin64xiDb407ZQGaK
5v4oRsnQn1KBhgZ2wfQ/S+adAma9IroK9F3C/Bm+IJ+mpNxJcbWPqnf9+5ExoxzU
MFyu0azan1crqWA/geJBetL4zVoRJx4qNEve0gqwk06vwLeIKyzB2jPO5dmn9pAb
kfAFCQgtTUGZHvZWyBZMWQcMKEQLSupOLYXU4b2Vf+oR9U0jvevqs3LArBsUceM9
vQw8Vg9RZiWs9lVeVYSQErYQecMhdiHYCXFuteaNH9tvATN4PumXiT2ZM9OsX6uy
jrXW7YLawJbGLIDNsAyrn8JESzY/CsRPpCIUq3JzL2VQdInC3mEl18rTEuKTBeZF
zE/RgwudhWDT58/vceS2LHa5KNd/vAzMTmUHEUwHg1N7TV3qkSgpPaVcvx4KklXv
1nKT2KcfD5K1Yy/InjxUYdGhRPYa7azl+l7W4hJ+NCGxwL+tUCg3knp80+empTJ0
mZm6/VSbc245nKjx3ydLlTbQ/xNMQXgHHDKPW6eO4ezZaydJZG2xkK3x6eF1+i0k
PWHSLjUxrK1AGrg=
=ri0M
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Reserve ECAM so we don't assign it to PCI BARs; this works around
bugs where BIOS included ECAM in a PNP0A03 host bridge window,
didn't reserve it via a PNP0C02 motherboard device, and didn't
allocate space for SR-IOV VF BARs (Bjorn Helgaas)
- Add MMCONFIG/ECAM debug logging (Bjorn Helgaas)
- Rename 'MMCONFIG' to 'ECAM' to match spec usage (Bjorn Helgaas)
- Log device type (Root Port, Switch Port, etc) during enumeration
(Bjorn Helgaas)
- Log bridges before downstream devices so the dmesg order is more
logical (Bjorn Helgaas)
- Log resource names (BAR 0, VF BAR 0, bridge window, etc)
consistently instead of a mix of names and "reg 0x10" (Puranjay
Mohan, Bjorn Helgaas)
- Fix 64GT/s effective data rate calculation to use 1b/1b encoding
rather than the 8b/10b or 128b/130b used by lower rates (Ilpo
Järvinen)
- Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI
lpfc (Ilpo Järvinen)
- Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen)
Resource management:
- Restructure pci_dev_for_each_resource() to avoid computing the
address of an out-of-bounds array element (the bounds check was
performed later so the element was never actually *read*, but it's
nicer to avoid even computing an out-of-bounds address) (Andy
Shevchenko)
Driver binding:
- Convert pci-host-common.c platform .remove() callback to
.remove_new() returning 'void' since it's not useful to return
error codes here (Uwe Kleine-König)
- Convert exynos, keystone, kirin from .remove() to .remove_new(),
which returns void instead of int (Uwe Kleine-König)
- Drop unused struct pci_driver.node member (Mathias Krause)
Virtualization:
- Add ACS quirk for more Zhaoxin Root Ports (LeoLiuoc)
Error handling:
- Log AER errors as "Correctable" (not "Corrected") or
"Uncorrectable" to match spec terminology (Bjorn Helgaas)
- Decode Requester ID when no error info found instead of printing
the raw hex value (Bjorn Helgaas)
Endpoint framework:
- Use a unique test pattern for each BAR in the pci_endpoint_test to
make it easier to debug address translation issues (Niklas Cassel)
Broadcom STB PCIe controller driver:
- Add DT property "brcm,clkreq-mode" and driver support for different
CLKREQ# modes to make ASPM L1.x states possible (Jim Quinlan)
Freescale Layerscape PCIe controller driver:
- Add suspend/resume support for Layerscape LS1043a and LS1021a,
including software-managed PME_Turn_Off and transitions between L0,
L2/L3_Ready Link states (Frank Li)
MediaTek PCIe controller driver:
- Clear MSI interrupt status before handler to avoid missing MSIs
that occur after the handler (qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 translation window setup to handle MMIO space
that is not a power of two in size (Jianjun Wang)
Qualcomm PCIe controller driver:
- Increase qcom iommu-map maxItems to accommodate SDX55 (five
entries) and SDM845 (sixteen entries) (Krzysztof Kozlowski)
- Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof
Kozlowski)
- Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof
Kozlowski)
- Correct the qcom "reset-name" property, previously incorrectly
called "reset-names" (Krzysztof Kozlowski)
- Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil
Armstrong)
Renesas R-Car PCIe controller driver:
- Replace of_device.h with explicit of.h include to untangle header
usage (Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v
regulators on KingFisher (Wolfram Sang)
SiFive FU740 PCIe controller driver:
- Convert fu740 CONFIG_PCIE_FU740 dependency from SOC_SIFIVE to
ARCH_SIFIVE (Conor Dooley)
Synopsys DesignWare PCIe controller driver:
- Align iATU mapping for endpoint MSI-X (Niklas Cassel)
- Drop "host_" prefix from struct dw_pcie_host_ops members (Yoshihiro
Shimoda)
- Drop "ep_" prefix from struct dw_pcie_ep_ops members (Yoshihiro
Shimoda)
- Rename struct dw_pcie_ep_ops.func_conf_select() to
.get_dbi_offset() to be more descriptive (Yoshihiro Shimoda)
- Add Endpoint DBI accessors to encapsulate offset lookups (Yoshihiro
Shimoda)
TI J721E PCIe driver:
- Add j721e DT and driver support for 'num-lanes' for devices that
support x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt
Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is
specific to those TI SoC parts (Peter Robinson)
TI Keystone PCIe controller driver:
- Hold power management references to all PHYs while enabling them to
avoid a race when one provides clocks to others (Siddharth
Vadapalli)
Xilinx XDMA PCIe controller driver:
- Remove redundant dev_err(), since platform_get_irq() and
platform_get_irq_byname() already log errors (Yang Li)
- Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
(Krzysztof Wilczyński)
- Fix xilinx_pl_dma_pcie_init_irq_domain() error return when
irq_domain_add_linear() fails (Harshit Mogalapalli)
MicroSemi Switchtec management driver:
- Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm
ioremapping in switchtec_pci_probe(). Previously the cleanup was
done in stdev_release(), which used stale pointers if stdev->cdev
happened to be open when the PCI device was removed (Daniel
Stodden)
Miscellaneous:
- Convert interrupt terminology from "legacy" to "INTx" to be more
specific and match spec terminology (Damien Le Moal)
- In dw-xdata-pcie, pci_endpoint_test, and vmd, replace usage of
deprecated ida_simple_*() API with ida_alloc() and ida_free()
(Christophe JAILLET)"
* tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Fix kernel-doc issues
PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode"
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
PCI: keystone: Fix race condition when initializing PHYs
PCI: xilinx-xdma: Fix error code in xilinx_pl_dma_pcie_init_irq_domain()
PCI: xilinx-xdma: Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
PCI: rcar-gen4: Fix -Wvoid-pointer-to-enum-cast error
PCI: iproc: Fix -Wvoid-pointer-to-enum-cast warning
PCI: dwc: Add dw_pcie_ep_{read,write}_dbi[2] helpers
PCI: dwc: Rename .func_conf_select to .get_dbi_offset in struct dw_pcie_ep_ops
PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_ops
PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members
misc: pci_endpoint_test: Use a unique test pattern for each BAR
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI/AER: Use explicit register sizes for struct members
PCI/AER: Decode Requester ID when no error info found
PCI/AER: Use 'Correctable' and 'Uncorrectable' spec terms for errors
...
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more explicit and match spec
terminology (Bjorn Helgaas)
- Use existing PCI_IRQ_INTX, PCI_IRQ_MSI, PCI_IRQ_MSIX in artpec6, cadence,
designware, designware-plat, dra7xx, imx6, keembay, keystone, layerscape,
mhi, ntb, qcom, rcar, rcar-gen4, rockchip, tegra194, uniphier, vntb; drop
the redundant pci_epc_irq_type enum with the same values (Damien Le Moal)
- Use "intx" instead of "leg" or "legacy" when describing INTx interrupts
in endpoint core, endpoint tests, cadence, dra7xx, designware,
dw-rockchip, dwc core, imx6, keystone, layerscape, qcom, rcar-gen4,
rockchip, tegra194, uniphier, xilinx-nwl (Damien Le Moal)
* pci/irq-clean-up:
PCI: xilinx-nwl: Use INTX instead of legacy
PCI: rockchip-host: Rename rockchip_pcie_legacy_int_handler()
PCI: rockchip-ep: Use INTX instead of legacy
PCI: uniphier: Use INTX instead of legacy
PCI: tegra194: Use INTX instead of legacy
PCI: dw-rockchip: Rename rockchip_pcie_legacy_int_handler()
PCI: keystone: Use INTX instead of legacy
PCI: dwc: Rename dw_pcie_ep_raise_legacy_irq()
PCI: cadence: Use INTX instead of legacy
PCI: dra7xx: Rename dra7xx_pcie_raise_legacy_irq()
misc: pci_endpoint_test: Use INTX instead of LEGACY
PCI: endpoint: Rename LEGACY to INTX in test function driver
PCI: endpoint: Use INTX instead of legacy
PCI: endpoint: Drop PCI_EPC_IRQ_XXX definitions
PCI: Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX
- Use ida_alloc() instead of deprecated ida_simple_get() (Christophe JAILLET)
* pci/controller/vmd:
PCI: vmd: Remove usage of the deprecated ida_simple_xx() API
- Replace of_device.h with explicit of.h include to untangle header usage
(Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v regulators
on KingFisher (Wolfram Sang)
* pci/controller/rcar:
PCI: rcar-host: Add support for optional regulators
dt-bindings: PCI: rcar-pci-host: Add optional regulators
PCI: rcar-gen4: Replace of_device.h with explicit of.h include
- Clear MSI interrupt status before handler to avoid missing MSIs that
occur after the handler (qizhong cheng)
- Update mediatek-gen3 translation window setup to handle MMIO space that
is not a power of two in size (Jianjun Wang)
* pci/controller/mediatek:
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
- Add suspend/resume support for Layerscape LS1043a, including
software-managed PME_Turn_Off and transitions between L0, L2/L3_Ready
Link states (Frank Li)
* pci/controller/layerscape:
PCI: layerscape: Add suspend/resume for ls1043a
PCI: layerscape(ep): Rename pf_* as pf_lut_*
PCI: layerscape: Add suspend/resume for ls1021a
PCI: layerscape: Add function pointer for exit_from_l2()
- Use devm_kasprintf() to dynamically allocate clock names, removing need
for an intermediate buffer (Christophe JAILLET)
* pci/controller/kirin:
PCI: kirin: Use devm_kasprintf() to dynamically allocate clock names
- Hold power management references to all PHYs while enabling them to avoid
a race when one provides clocks to others (Siddharth Vadapalli)
* pci/controller/keystone:
PCI: keystone: Fix race condition when initializing PHYs
- Add j721e DT and driver support for 'num-lanes' for devices that support
x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is specific to
those TI SoC parts (Peter Robinson)
* pci/controller/cadence:
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI: j721e: Add PCIe 4x lane selection support
PCI: j721e: Add per platform maximum lane settings
dt-bindings: PCI: ti,j721e-pci-*: Add j784s4-pci-* compatible strings
dt-bindings: PCI: ti,j721e-pci-*: Add checks for num-lanes
- Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm
ioremapping in switchtec_pci_probe(). Previously the cleanup was done in
stdev_release(), which used stale pointers if stdev->cdev happened to be
open when the PCI device was removed (Daniel Stodden)
* pci/switchtec:
PCI: switchtec: Fix stdev_release() crash after surprise hot remove
- Log device type (Root Port, Switch Port, etc) during enumeration (Bjorn
Helgaas)
- Log resource names (BAR 0, VF BAR 0, bridge window, etc) consistently
instead of a mix of names and "reg 0x10" (Puranjay Mohan, Bjorn Helgaas)
- Log bridges before devices below the bridges (Bjorn Helgaas)
* pci/enumeration-logging:
PCI: Log bridge info when first enumerating bridge
PCI: Log bridge windows conditionally
PCI: Supply bridge device, not secondary bus, to read window details
PCI: Move pci_read_bridge_windows() below individual window accessors
PCI: Use resource names in PCI log messages
PCI: Update BAR # and window messages
PCI: Log device type during enumeration
- Convert pci-host-common.c platform .remove() callback to .remove_new()
returning 'void' since it's not useful to return error codes here (Uwe
Kleine-König)
- Log a message about updating AMD USB controller class code (so dwc3, not
xhci, claims it) only when we actually change it (Guilherme G. Piccoli)
- Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI lpfc
(Ilpo Järvinen)
- Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen)
- Fix 64GT/s effective data rate calculation to use 1b/1b encoding rather
than the 8b/10b or 128b/130b used by lower rates (Ilpo Järvinen)
* pci/enumeration:
PCI: Fix 64GT/s effective data rate calculation
x86/pci: Clean up open-coded PCIBIOS return code mangling
scsi: lpfc: Use PCI_HEADER_TYPE_MFD instead of literal
powerpc/fsl-pci: Use PCI_HEADER_TYPE_MASK instead of literal
x86/pci: Use PCI_HEADER_TYPE_* instead of literals
PCI: Only override AMD USB controller if required
PCI: host-generic: Convert to platform remove callback returning void
Core & protocols
----------------
- Analyze and reorganize core networking structs (socks, netdev,
netns, mibs) to optimize cacheline consumption and set up
build time warnings to safeguard against future header changes.
This improves TCP performances with many concurrent connections
up to 40%.
- Add page-pool netlink-based introspection, exposing the
memory usage and recycling stats. This helps indentify
bad PP users and possible leaks.
- Refine TCP/DCCP source port selection to no longer favor even
source port at connect() time when IP_LOCAL_PORT_RANGE is set.
This lowers the time taken by connect() for hosts having
many active connections to the same destination.
- Refactor the TCP bind conflict code, shrinking related socket
structs.
- Refactor TCP SYN-Cookie handling, as a preparation step to
allow arbitrary SYN-Cookie processing via eBPF.
- Tune optmem_max for 0-copy usage, increasing the default value
to 128KB and namespecifying it.
- Allow coalescing for cloned skbs coming from page pools, improving
RX performances with some common configurations.
- Reduce extension header parsing overhead at GRO time.
- Add bridge MDB bulk deletion support, allowing user-space to
request the deletion of matching entries.
- Reorder nftables struct members, to keep data accessed by the
datapath first.
- Introduce TC block ports tracking and use. This allows supporting
multicast-like behavior at the TC layer.
- Remove UAPI support for retired TC qdiscs (dsmark, CBQ and ATM) and
classifiers (RSVP and tcindex).
- More data-race annotations.
- Extend the diag interface to dump TCP bound-only sockets.
- Conditional notification of events for TC qdisc class and actions.
- Support for WPAN dynamic associations with nearby devices, to form
a sub-network using a specific PAN ID.
- Implement SMCv2.1 virtual ISM device support.
- Add support for Batman-avd mulicast packet type.
BPF
---
- Tons of verifier improvements:
- BPF register bounds logic and range support along with a large
test suite
- log improvements
- complete precision tracking support for register spills
- track aligned STACK_ZERO cases as imprecise spilled registers. It
improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs
- support for user's global BPF subprogram arguments with few
commonly requested annotations for a better developer experience
- support tracking of BPF_JNE which helps cases when the compiler
transforms (unsigned) "a > 0" into "if a == 0 goto xxx" and the
like
- several fixes
- Add initial TX metadata implementation for AF_XDP with support in
mlx5 and stmmac drivers. Two types of offloads are supported right
now, that is, TX timestamp and TX checksum offload.
- Fix kCFI bugs in BPF all forms of indirect calls from BPF into
kernel and from kernel into BPF work with CFI enabled. This allows
BPF to work with CONFIG_FINEIBT=y.
- Change BPF verifier logic to validate global subprograms lazily
instead of unconditionally before the main program, so they can be
guarded using BPF CO-RE techniques.
- Support uid/gid options when mounting bpffs.
- Add a new kfunc which acquires the associated cgroup of a task
within a specific cgroup v1 hierarchy where the latter is identified
by its id.
- Extend verifier to allow bpf_refcount_acquire() of a map value field
obtained via direct load which is a use-case needed in sched_ext.
- Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter.
- Support for VLAN tag in XDP hints.
- Remove deprecated bpfilter kernel leftovers given the project
is developed in user-space (https://github.com/facebook/bpfilter).
Misc
----
- Support for parellel TC self-tests execution.
- Increase MPTCP self-tests coverage.
- Updated the bridge documentation, including several so-far
undocumented features.
- Convert all the net self-tests to run in unique netns, to
avoid random failures due to conflict and allow concurrent
runs.
- Add TCP-AO self-tests.
- Add kunit tests for both cfg80211 and mac80211.
- Autogenerate Netlink families documentation from YAML spec.
- Add yml-gen support for fixed headers and recursive nests, the
tool can now generate user-space code for all genetlink families
for which we have specs.
- A bunch of additional module descriptions fixes.
- Catch incorrect freeing of pages belonging to a page pool.
Driver API
----------
- Rust abstractions for network PHY drivers; do not cover yet the
full C API, but already allow implementing functional PHY drivers
in rust.
- Introduce queue and NAPI support in the netdev Netlink interface,
allowing complete access to the device <> NAPIs <> queues
relationship.
- Introduce notifications filtering for devlink to allow control
application scale to thousands of instances.
- Improve PHY validation, requesting rate matching information for
each ethtool link mode supported by both the PHY and host.
- Add support for ethtool symmetric-xor RSS hash.
- ACPI based Wifi band RFI (WBRF) mitigation feature for the AMD
platform.
- Expose pin fractional frequency offset value over new DPLL generic
netlink attribute.
- Convert older drivers to platform remove callback returning void.
- Add support for PHY package MMD read/write.
New hardware / drivers
----------------------
- Ethernet:
- Octeon CN10K devices
- Broadcom 5760X P7
- Qualcomm SM8550 SoC
- Texas Instrument DP83TG720S PHY
- Bluetooth:
- IMC Networks Bluetooth radio
Removed
-------
- WiFi:
- libertas 16-bit PCMCIA support
- Atmel at76c50x drivers
- HostAP ISA/PCMCIA style 802.11b driver
- zd1201 802.11b USB dongles
- Orinoco ISA/PCMCIA 802.11b driver
- Aviator/Raytheon driver
- Planet WL3501 driver
- RNDIS USB 802.11b driver
Drivers
-------
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- allow one by one port representors creation and removal
- add temperature and clock information reporting
- add get/set for ethtool's header split ringparam
- add again FW logging
- adds support switchdev hardware packet mirroring
- iavf: implement symmetric-xor RSS hash
- igc: add support for concurrent physical and free-running timers
- i40e: increase the allowable descriptors
- nVidia/Mellanox:
- Preparation for Socket-Direct multi-dev netdev. That will allow
in future releases combining multiple PFs devices attached to
different NUMA nodes under the same netdev
- Broadcom (bnxt):
- TX completion handling improvements
- add basic ntuple filter support
- reduce MSIX vectors usage for MQPRIO offload
- add VXLAN support, USO offload and TX coalesce completion for P7
- Marvell Octeon EP:
- xmit-more support
- add PF-VF mailbox support and use it for FW notifications for VFs
- Wangxun (ngbe/txgbe):
- implement ethtool functions to operate pause param, ring param,
coalesce channel number and msglevel
- Netronome/Corigine (nfp):
- add flow-steering support
- support UDP segmentation offload
- Ethernet NICs embedded, slower, virtual:
- Xilinx AXI: remove duplicate DMA code adopting the dma engine driver
- stmmac: add support for HW-accelerated VLAN stripping
- TI AM654x sw: add mqprio, frame preemption & coalescing
- gve: add support for non-4k page sizes.
- virtio-net: support dynamic coalescing moderation
- nVidia/Mellanox Ethernet datacenter switches:
- allow firmware upgrade without a reboot
- more flexible support for bridge flooding via the compressed
FID flooding mode
- Ethernet embedded switches:
- Microchip:
- fine-tune flow control and speed configurations in KSZ8xxx
- KSZ88X3: enable setting rmii reference
- Renesas:
- add jumbo frames support
- Marvell:
- 88E6xxx: add "eth-mac" and "rmon" stats support
- Ethernet PHYs:
- aquantia: add firmware load support
- at803x: refactor the driver to simplify adding support for more
chip variants
- NXP C45 TJA11xx: Add MACsec offload support
- Wifi:
- MediaTek (mt76):
- NVMEM EEPROM improvements
- mt7996 Extremely High Throughput (EHT) improvements
- mt7996 Wireless Ethernet Dispatcher (WED) support
- mt7996 36-bit DMA support
- Qualcomm (ath12k):
- support for a single MSI vector
- WCN7850: support AP mode
- Intel (iwlwifi):
- new debugfs file fw_dbg_clear
- allow concurrent P2P operation on DFS channels
- Bluetooth:
- QCA2066: support HFP offload
- ISO: more broadcast-related improvements
- NXP: better recovery in case receiver/transmitter get out of sync
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=1bW6
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"The most interesting thing is probably the networking structs
reorganization and a significant amount of changes is around
self-tests.
Core & protocols:
- Analyze and reorganize core networking structs (socks, netdev,
netns, mibs) to optimize cacheline consumption and set up build
time warnings to safeguard against future header changes
This improves TCP performances with many concurrent connections up
to 40%
- Add page-pool netlink-based introspection, exposing the memory
usage and recycling stats. This helps indentify bad PP users and
possible leaks
- Refine TCP/DCCP source port selection to no longer favor even
source port at connect() time when IP_LOCAL_PORT_RANGE is set. This
lowers the time taken by connect() for hosts having many active
connections to the same destination
- Refactor the TCP bind conflict code, shrinking related socket
structs
- Refactor TCP SYN-Cookie handling, as a preparation step to allow
arbitrary SYN-Cookie processing via eBPF
- Tune optmem_max for 0-copy usage, increasing the default value to
128KB and namespecifying it
- Allow coalescing for cloned skbs coming from page pools, improving
RX performances with some common configurations
- Reduce extension header parsing overhead at GRO time
- Add bridge MDB bulk deletion support, allowing user-space to
request the deletion of matching entries
- Reorder nftables struct members, to keep data accessed by the
datapath first
- Introduce TC block ports tracking and use. This allows supporting
multicast-like behavior at the TC layer
- Remove UAPI support for retired TC qdiscs (dsmark, CBQ and ATM) and
classifiers (RSVP and tcindex)
- More data-race annotations
- Extend the diag interface to dump TCP bound-only sockets
- Conditional notification of events for TC qdisc class and actions
- Support for WPAN dynamic associations with nearby devices, to form
a sub-network using a specific PAN ID
- Implement SMCv2.1 virtual ISM device support
- Add support for Batman-avd mulicast packet type
BPF:
- Tons of verifier improvements:
- BPF register bounds logic and range support along with a large
test suite
- log improvements
- complete precision tracking support for register spills
- track aligned STACK_ZERO cases as imprecise spilled registers.
This improves the verifier "instructions processed" metric from
single digit to 50-60% for some programs
- support for user's global BPF subprogram arguments with few
commonly requested annotations for a better developer
experience
- support tracking of BPF_JNE which helps cases when the compiler
transforms (unsigned) "a > 0" into "if a == 0 goto xxx" and the
like
- several fixes
- Add initial TX metadata implementation for AF_XDP with support in
mlx5 and stmmac drivers. Two types of offloads are supported right
now, that is, TX timestamp and TX checksum offload
- Fix kCFI bugs in BPF all forms of indirect calls from BPF into
kernel and from kernel into BPF work with CFI enabled. This allows
BPF to work with CONFIG_FINEIBT=y
- Change BPF verifier logic to validate global subprograms lazily
instead of unconditionally before the main program, so they can be
guarded using BPF CO-RE techniques
- Support uid/gid options when mounting bpffs
- Add a new kfunc which acquires the associated cgroup of a task
within a specific cgroup v1 hierarchy where the latter is
identified by its id
- Extend verifier to allow bpf_refcount_acquire() of a map value
field obtained via direct load which is a use-case needed in
sched_ext
- Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter
- Support for VLAN tag in XDP hints
- Remove deprecated bpfilter kernel leftovers given the project is
developed in user-space (https://github.com/facebook/bpfilter)
Misc:
- Support for parellel TC self-tests execution
- Increase MPTCP self-tests coverage
- Updated the bridge documentation, including several so-far
undocumented features
- Convert all the net self-tests to run in unique netns, to avoid
random failures due to conflict and allow concurrent runs
- Add TCP-AO self-tests
- Add kunit tests for both cfg80211 and mac80211
- Autogenerate Netlink families documentation from YAML spec
- Add yml-gen support for fixed headers and recursive nests, the tool
can now generate user-space code for all genetlink families for
which we have specs
- A bunch of additional module descriptions fixes
- Catch incorrect freeing of pages belonging to a page pool
Driver API:
- Rust abstractions for network PHY drivers; do not cover yet the
full C API, but already allow implementing functional PHY drivers
in rust
- Introduce queue and NAPI support in the netdev Netlink interface,
allowing complete access to the device <> NAPIs <> queues
relationship
- Introduce notifications filtering for devlink to allow control
application scale to thousands of instances
- Improve PHY validation, requesting rate matching information for
each ethtool link mode supported by both the PHY and host
- Add support for ethtool symmetric-xor RSS hash
- ACPI based Wifi band RFI (WBRF) mitigation feature for the AMD
platform
- Expose pin fractional frequency offset value over new DPLL generic
netlink attribute
- Convert older drivers to platform remove callback returning void
- Add support for PHY package MMD read/write
New hardware / drivers:
- Ethernet:
- Octeon CN10K devices
- Broadcom 5760X P7
- Qualcomm SM8550 SoC
- Texas Instrument DP83TG720S PHY
- Bluetooth:
- IMC Networks Bluetooth radio
Removed:
- WiFi:
- libertas 16-bit PCMCIA support
- Atmel at76c50x drivers
- HostAP ISA/PCMCIA style 802.11b driver
- zd1201 802.11b USB dongles
- Orinoco ISA/PCMCIA 802.11b driver
- Aviator/Raytheon driver
- Planet WL3501 driver
- RNDIS USB 802.11b driver
Driver updates:
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- allow one by one port representors creation and removal
- add temperature and clock information reporting
- add get/set for ethtool's header split ringparam
- add again FW logging
- adds support switchdev hardware packet mirroring
- iavf: implement symmetric-xor RSS hash
- igc: add support for concurrent physical and free-running
timers
- i40e: increase the allowable descriptors
- nVidia/Mellanox:
- Preparation for Socket-Direct multi-dev netdev. That will
allow in future releases combining multiple PFs devices
attached to different NUMA nodes under the same netdev
- Broadcom (bnxt):
- TX completion handling improvements
- add basic ntuple filter support
- reduce MSIX vectors usage for MQPRIO offload
- add VXLAN support, USO offload and TX coalesce completion
for P7
- Marvell Octeon EP:
- xmit-more support
- add PF-VF mailbox support and use it for FW notifications
for VFs
- Wangxun (ngbe/txgbe):
- implement ethtool functions to operate pause param, ring
param, coalesce channel number and msglevel
- Netronome/Corigine (nfp):
- add flow-steering support
- support UDP segmentation offload
- Ethernet NICs embedded, slower, virtual:
- Xilinx AXI: remove duplicate DMA code adopting the dma engine
driver
- stmmac: add support for HW-accelerated VLAN stripping
- TI AM654x sw: add mqprio, frame preemption & coalescing
- gve: add support for non-4k page sizes.
- virtio-net: support dynamic coalescing moderation
- nVidia/Mellanox Ethernet datacenter switches:
- allow firmware upgrade without a reboot
- more flexible support for bridge flooding via the compressed
FID flooding mode
- Ethernet embedded switches:
- Microchip:
- fine-tune flow control and speed configurations in KSZ8xxx
- KSZ88X3: enable setting rmii reference
- Renesas:
- add jumbo frames support
- Marvell:
- 88E6xxx: add "eth-mac" and "rmon" stats support
- Ethernet PHYs:
- aquantia: add firmware load support
- at803x: refactor the driver to simplify adding support for more
chip variants
- NXP C45 TJA11xx: Add MACsec offload support
- Wifi:
- MediaTek (mt76):
- NVMEM EEPROM improvements
- mt7996 Extremely High Throughput (EHT) improvements
- mt7996 Wireless Ethernet Dispatcher (WED) support
- mt7996 36-bit DMA support
- Qualcomm (ath12k):
- support for a single MSI vector
- WCN7850: support AP mode
- Intel (iwlwifi):
- new debugfs file fw_dbg_clear
- allow concurrent P2P operation on DFS channels
- Bluetooth:
- QCA2066: support HFP offload
- ISO: more broadcast-related improvements
- NXP: better recovery in case receiver/transmitter get out of sync"
* tag 'net-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1714 commits)
lan78xx: remove redundant statement in lan78xx_get_eee
lan743x: remove redundant statement in lan743x_ethtool_get_eee
bnxt_en: Fix RCU locking for ntuple filters in bnxt_rx_flow_steer()
bnxt_en: Fix RCU locking for ntuple filters in bnxt_srxclsrldel()
bnxt_en: Remove unneeded variable in bnxt_hwrm_clear_vnic_filter()
tcp: Revert no longer abort SYN_SENT when receiving some ICMP
Revert "mlx5 updates 2023-12-20"
Revert "net: stmmac: Enable Per DMA Channel interrupt"
ipvlan: Remove usage of the deprecated ida_simple_xx() API
ipvlan: Fix a typo in a comment
net/sched: Remove ipt action tests
net: stmmac: Use interrupt mode INTM=1 for per channel irq
net: stmmac: Add support for TX/RX channel interrupt
net: stmmac: Make MSI interrupt routine generic
dt-bindings: net: snps,dwmac: per channel irq
net: phy: at803x: make read_status more generic
net: phy: at803x: add support for cdt cross short test for qca808x
net: phy: at803x: refactor qca808x cable test get status function
net: phy: at803x: generalize cdt fault length function
net: ethernet: cortina: Drop TSO support
...
The Broadcom STB/CM PCIe HW core, which is also used in RPi SOCs, must be
deliberately set by the PCIe RC HW into one of three mutually exclusive
modes:
"safe" -- No CLKREQ# expected or required, refclk is always provided. This
mode should work for all devices but is not be capable of any refclk
power savings.
"no-l1ss" -- CLKREQ# is expected to be driven by the downstream device for
CPM and ASPM L0s and L1. Provides Clock Power Management, L0s, and L1,
but cannot provide L1 substate (L1SS) power savings. If the downstream
device connected to the RC is L1SS capable AND the OS enables L1SS, all
PCIe traffic may abruptly halt, potentially hanging the system.
"default" -- Bidirectional CLKREQ# between the RC and downstream device.
Provides ASPM L0s, L1, and L1SS, but not compliant to provide Clock
Power Management; specifically, may not be able to meet the T_CLRon max
timing of 400ns as specified in "Dynamic Clock Control", section
3.2.5.2.2 of the PCIe Express Mini CEM 2.1 specification. This
situation is atypical and should happen only with older devices.
Previously, this driver always set the mode to "no-l1ss", as almost all
STB/CM boards operate in this mode. But now there is interest in
activating L1SS power savings from STB/CM customers, which requires "aspm"
mode. In addition, a bug was filed for RPi4 CM platform because most
devices did not work in "no-l1ss" mode.
Note that the mode is specified by the DT property "brcm,clkreq-mode". If
this property is omitted, then "default" mode is chosen.
Note: Since L1 substates are now possible, a modification was made
regarding an internal bus timeout: During long periods of the PCIe RC HW
being in an L1SS sleep state, there may be a timeout on an internal bus
access, even though there may not be any PCIe access involved. Such a
timeout will cause a subsequent CPU abort.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217276
Link: https://lore.kernel.org/linux-pci/20231113185607.1756-3-james.quinlan@broadcom.com
Tested-by: Cyril Brulebois <cyril@debamax.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.
For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.
Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579b9 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
