IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add initial version of device tree for Facebook Wedge100 AST2400 BMC
platform.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Wedge40 AST2400 BMC
platform.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
"git diff" says:
\ No newline at end of file
after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") seem to have missed this
one file.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Change the FSI clock and data GPIOs to match what the hardware turned
out to use.
Fixes: 8e8fd0cbd7c5 ("ARM: dts: aspeed: Add Swift BMC machine")
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Adriana Kobylak <anoo@us.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The dma dts node was missing the reset-names = "dma". The reset driver
needs this line to get the reset property.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Adjust GMAC1 clock lines skew to maximum (+960 ps) and TXD lines skew
to minimum (-420 ps), to improve signal integrity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add missing buttons and signals to the VINING FPGA device tree,
so they are presented to the userspace via gpio-keys evdev.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
With commit d8e8fd0ebf8b ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Move USB PHYs to a standard arrays for Exynos EHCI/OHCI devices. This
resolves the conflict between Exynos EHCI/OHCI sub-nodes and generic USB
device bindings. Once the Exynos EHCI/OHCI sub-nodes are removed, the
boards can finally provide sub-nodes for the USB devices using generic USB
device bindings.
Suggested-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20190726081453.9456-4-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a space before and after assignment operator to have consistent
style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This switches the kernel to parse the Redboot partitions
in the SL93512r and the NAS4220B properly using the
right compatible string instead of using hard-coded
partitions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SL93512r board has its pin muxing set up for the wrong
ASIC: SL3516 instead of SL3512 that it is using. Fix it
up and reference the right GPIO for the WPS button.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also known as the AOpen Chromebase Mini.
tiger and fievel are share the same board, tiger has a display and
touchscreen, fievel not. Use the fievel .dts as base and add the
extra bits.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
veyron jaq, jerry, minnie and speedy have mostly redundant regulator
and pinctrl configurations for the panel/backlight. Consolidate these
pieces in the eDP .dtsi.
Also change the default power supply for the panel to
'panel_regulator', instead of overriding it in all the board files.
pinky is the only device that uses 'vcc33_lcd' (the prior default),
so overwrite it in this case. pinky doesn't have a complete display
configuration, to keep things as they were delete the common nodes
that didn't exist previously in pinky's board file.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The chromebook .dtsi file contains common settings for veyron
Chromebooks with eDP displays. Some veyron devices with a display
aren't Chromebooks (e.g. 'tiger' aka 'AOpen Chromebase Mini'), move
display related bits from the chromebook .dtsi into a separate file
to avoid redundant DT settings.
The new file is included from the chromebook .dtsi and can be
included by non-Chromebook devices with a display.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The downstream Chrome OS 3.14 kernel for jerry limits WiFi TX power
through calibration data in the device tree [1]. Add a DT node for
the WiFi chip and use the downstream calibration data.
Not all calibration data entries have the length specified in the
binding (Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt),
however this is the data used by the downstream ('official') kernel
and the binding mentions that "the length can vary between hw
versions".
[1] https://crrev.com/c/271237
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds FMC2 NAND controller support used by stm32mp157c SOC.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The assigned register ranges for UART, SPI and I2C were too wasteful.
In order to avoid overlapping with the new functions on BCM2711
reduce the ranges.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
Since A31, memory mapping of the IR driver has changed.
Prefer the A31 bindings instead of A13.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since A31, memory mapping of the IR driver has changed.
Prefer the A31 bindings instead of A13.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We are currently using a wrong register for dcan revision. Although
this is currently only used for detecting the dcan module, let's
fix it to avoid confusion.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at
the interconnect target module level for the modules that have it
defined. Otherwise we get the following warnings:
dts flag should be at module level for ti,no-idle-on-init
dts flag should be at module level for ti,no-reset-on-init
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix i.MX8MM SAI3 RXC/TXFS pinmux configuration.
- Fix i.MX7ULP usb-phy unit address to drop extra '0x' notation.
- Fix typo of clock frequency property name in a few i.MX6UL board
I2C buses.
- Drop "fsl,imx6sx-sai" from i.MX8M SAI device, as it's not compatible
with i.MX6SX SAI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdNs2iAAoJEFBXWFqHsHzOyZ8H/3u3AjWSJxUa845cro1Q/Ibh
Ap2Skk9NgX3Wo9oRaet6Nc44iXG4zBXYfhVyzUG5H6t2mk4S2c2RaKLd55n6mHz0
6q1G57Z9ogxBzXrWgbiZtlCOlzZCNXVWZiB5eIUT12Mway+0HMEe4zcKAEvADZnt
c2tFf2AbjRe0ye1M2a6V09/TunIT8Hv2XH88vA4MxAJauOWNTkx4TrmXVNnokax+
S5Ha0Djr7seuHf6HLr95lB7QAj0ozTpZY17HsOmdFaO2UREVftm7JMhaNmxL072u
by1hwAALp9vYaDDzfw+7NjaquJiF6rGO6Vgi78d3brBFcXPSXmXpufUffl1aFWE=
=pQlh
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.3:
- Fix i.MX8MM SAI3 RXC/TXFS pinmux configuration.
- Fix i.MX7ULP usb-phy unit address to drop extra '0x' notation.
- Fix typo of clock frequency property name in a few i.MX6UL board
I2C buses.
- Drop "fsl,imx6sx-sai" from i.MX8M SAI device, as it's not compatible
with i.MX6SX SAI.
* tag 'imx-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq: fix SAI compatible
arm64: dts: imx8mm: Correct SAI3 RXC/TXFS pin's mux option #1
ARM: dts: imx6ul: fix clock frequency property name of I2C buses
ARM: dts: imx7ulp: Fix usb-phy unit address format
Link: https://lore.kernel.org/r/20190723090827.GU15632@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Even though the binding mentions that the PHY name must be "phy", it turns
out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change
our DTs to match the binding, without any side effect.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
simple-panel based bindings need only the display compatible, and
simple-panel isn't documented anywhere. Remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The thermal driver for the DB8500 was never properly converted
to device tree, the node should definitely be activated for
all board variants so move this down into the main SoC
DTSI, and default on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In addition to the PHYTEC phyCORE-i.MX 6UL the PHYTEC phyBOARD-Segin is
also available with the PHYTEC phyCORE-i.MX 6ULL. So this adds support
for this SOM and its baseboards.
It comes in a full featured option with either NAND flash or eMMC and in
a low cost option only available with NAND flash.
The hardware specs are:
- Full featured with NAND or eMMC:
* i.MX 6ULL Y2
* 512MB DDR3 memory
* 512MB NAND flash or 4GB/8GB eMMC
* Dual 10/100 Ethernet
* USB Host and USB OTG
* RS232
* MicroSD external storage
* Audio, RS232, I2C, SPI, CAN headers
* Further I/O options via A/V and Expansion headers
- Low cost with NAND:
* i.MX 6ULL Y0
* 256MB DDR3 memory
* 128MB NAND flash
* Single 10/100 Ethernet
* USB OTG
* RS232
* MicroSD external storage
* I2C
* Further I/O options via Expansion headers
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the imx6ul.dtsi include to the dts files so it is easier to reuse
the SOM dtsi for e.g. an i.MX 6ULL SOM.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ECSPI interface is available on the expansion connector of every
PHYTEC phyBOARD-Segin. Move its definition to the board include file
for better reuse.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The phyCORE-i.MX 6UL/ULL now can have eMMC instead of the NAND flash
memory. Add the eMMC node and disable it by default so it can be enabled
in case it is populated.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The phyCORE-i.MX 6UL/ULL now comes either with NAND flash or eMMC. We
have to configure the populated memory type in the device tree files. So
the GPMI node gets disabled by default and only enabled if populated.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To disable Ethernet interfaces in case they are not populated
make the FEC and Ethernet PHY status configurable in the dts files.
Also change the Ethernet PHYs labels to make them correspond to
the MDIO address.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
