IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
New drivers
- Driver for OneXPlayer mini AMD sensors
- Ampere's Altra smpro-hwmon driver
New chip and attribute support in existing drivers
- nct6775: Support for ASUS CROSSHAIR VIII/TUF/ProArt B550M
- pmbus/ltc2978: Support for LTC7132
- aquacomputer_d5next: Support for temperature sensor offsets
and flow sensor pulses
- coretemp: Support for dynamic ttarget and tjmax
Improvements
- Use devm_regulator_get_enable() where appropriate
- Use sysfs_emit() instead of scnprintf()
- Remove some useless #include <linux/hwmon-vid.h>
- Include <linux/kstrtox.h> when appropriate
- Use simple i2c probe
- it87: Check for a valid chip before using force_id, and new
new module parameter to ignore ACPI resource conflicts
- jc42: Use regmap, and restore min/max/critical temperatures on resume
- Add reporting power good and status to PMBus based regulators
Last minute fixes
- emc2305: Fix probing of emc2301/2/3, and fix setting pwm values
manually if THERMAL is enabled
Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----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=O7h4
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Driver for OneXPlayer mini AMD sensors
- Ampere's Altra smpro-hwmon driver
New chip and attribute support in existing drivers:
- nct6775: Support for ASUS CROSSHAIR VIII/TUF/ProArt B550M
- pmbus/ltc2978: Support for LTC7132
- aquacomputer_d5next: Support for temperature sensor offsets and
flow sensor pulses
- coretemp: Support for dynamic ttarget and tjmax
Improvements:
- Use devm_regulator_get_enable() where appropriate
- Use sysfs_emit() instead of scnprintf()
- Remove some useless #include <linux/hwmon-vid.h>
- Include <linux/kstrtox.h> when appropriate
- Use simple i2c probe
- it87: Check for a valid chip before using force_id, and new new
module parameter to ignore ACPI resource conflicts
- jc42: Use regmap, and restore min/max/critical temperatures on
resume
- Add reporting power good and status to PMBus based regulators
Last minute fixes:
- emc2305: Fix probing of emc2301/2/3, and fix setting pwm values
manually if THERMAL is enabled
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (37 commits)
hwmon: (emc2305) fix pwm never being able to set lower
hwmon: (emc2305) fix unable to probe emc2301/2/3
hwmon: (dell-smm) Move error message to make probing silent
hwmon: use sysfs_emit() to instead of scnprintf()
hwmon: (oxp-sensors) Fix pwm reading
hwmon: (aquacomputer_d5next) Add support for Quadro flow sensor pulses
hwmon: (pmbus/core) Implement regulator get_status
hwmon: (oxp-sensors) Add AOK ZOE and Mini PRO
hwmon: (gsc-hwmon) Switch to flexible array to simplify code
hwmon: (pmbus) Add power good support
hwmon: (nct6775) add ASUS CROSSHAIR VIII/TUF/ProArt B550M
hwmon: (coretemp) Add support for dynamic ttarget
hwmon: (coretemp) Add support for dynamic tjmax
hwmon: (coretemp) rearrange tjmax handing code
hwmon: Remove some useless #include <linux/hwmon-vid.h>
hwmon: (coretemp) Remove obsolete temp_data->valid
hwmon: add OneXPlayer mini AMD sensors driver
hwmon: (aquacomputer_d5next) Clear up macros and comments
hwmon: (it87) Add DMI table for future extensions
hwmon: Include <linux/kstrtox.h> when appropriate
...
Merge ACPI changes related to device enumeration, device object
managenet, operation region handling, table parsing and sysfs
interface:
- Use ZERO_PAGE(0) instead of empty_zero_page in the ACPI device
enumeration code (Giulio Benetti).
- Change the return type of the ACPI driver remove callback to void and
update its users accordingly (Dawei Li).
- Add general support for FFH address space type and implement the low-
level part of it for ARM64 (Sudeep Holla).
- Fix stale comments in the ACPI tables parsing code and make it print
more messages related to MADT (Hanjun Guo, Huacai Chen).
- Replace invocations of generic library functions with more kernel-
specific counterparts in the ACPI sysfs interface (Christophe JAILLET,
Xu Panda).
* acpi-scan:
ACPI: scan: substitute empty_zero_page with helper ZERO_PAGE(0)
* acpi-bus:
ACPI: FFH: Silence missing prototype warnings
ACPI: make remove callback of ACPI driver void
ACPI: bus: Fix the _OSC capability check for FFH OpRegion
arm64: Add architecture specific ACPI FFH Opregion callbacks
ACPI: Implement a generic FFH Opregion handler
* acpi-tables:
ACPI: tables: Fix the stale comments for acpi_locate_initial_tables()
ACPI: tables: Print CORE_PIC information when MADT is parsed
* acpi-sysfs:
ACPI: sysfs: use sysfs_emit() to instead of scnprintf()
ACPI: sysfs: Use kstrtobool() instead of strtobool()
There are fields 'last_hwmon_state' and 'last_thermal_state' in the
structure 'emc2305_cdev_data', which respectively store the cooling state
set by the 'hwmon' and 'thermal' subsystem, and the driver author hopes
that if the state set by 'hwmon' is lower than the value set by 'thermal',
the driver will just save it without actually setting the pwm. Currently,
the 'last_thermal_state' also be updated by 'hwmon', which will cause the
cooling state to never be set to a lower value. This patch fixes that.
Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com>
Link: https://lore.kernel.org/r/20221206055331.170459-2-nanpuyue@gmail.com
Fixes: 0d8400c5a2 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.")
[groeck: renamed emc2305_set_cur_state_shim -> __emc2305_set_cur_state]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The definitions of 'EMC2305_REG_PRODUCT_ID' and 'EMC2305_REG_DEVICE' are
both '0xfd', they actually return the same value, but the values returned
by emc2301/2/3/5 are different, so probe emc2301/2/3 will fail, This patch
fixes that.
Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com>
Link: https://lore.kernel.org/r/20221206055331.170459-1-nanpuyue@gmail.com
Fixes: 0d8400c5a2 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If dell-smm-hwmon loads on unsupported hardware like the
Dell XPS 17 9710, an error message is printed.
This might confuse users, as drivers are expected to be
silent if no supported hardware is found.
Reorder the error message so its only printed when the
driver is loaded with the "force" option being set.
Also reword the error message slightly.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20221130183418.357246-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the AOK ZOE A1 and OXP Mini PRO handheld devices.
DMI strings are added to this driver since the same EC layout is used and
has similar specs as the OXP mini AMD.
The added devices are:
- OneXPlayer mini PRO (AMD 6800U)
- AOK ZOE A1 (AMD 6800U)
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221125114901.11309-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using flexible array is more straight forward. It
- saves 1 pointer in the 'gsc_hwmon_platform_data' structure
- saves an indirection when using this array
- saves some LoC and avoids some always spurious pointer arithmetic
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/61a23e1d642397cfcecc4ac3bb0ab485d257987d.1668936855.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update error flags with regulation out if regulator is on & power
good status bit is set
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20221117184022.1808508-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boards such as
* ProArt B550-CREATOR
* ProArt Z490-CREATOR 10G
* ROG CROSSHAIR VIII EXTREME
* ROG CROSSHAIR VIII HERO (WI-FI)
* TUF GAMING B550M-E
* TUF GAMING B550M-E (WI-FI)
* TUF GAMING B550M-PLUS WIFI II
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Reported-by: yutesdb <mundanedefoliation@gmail.com>
Tested-by: yutesdb <mundanedefoliation@gmail.com>
Link: https://lore.kernel.org/r/20221114214456.3891-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET can be changed at
runtime when the Intel SST-PP (Intel Speed Select Technology -
Performance Profile) level is changed. As a result, the ttarget value
also becomes dyamic.
Improve the code to always get updated ttarget value.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113153145.32696-4-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET can be changed at
runtime when the Intel SST-PP (Intel Speed Select Technology -
Performance Profile) level is changed.
Improve the code to always use updated tjmax when it can be retrieved
from MSR_IA32_TEMPERATURE_TARGET.
When tjmax can not be retrieved from MSR_IA32_TEMPERATURE_TARGET, still
follow the previous logic and always use a static tjmax value.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113153145.32696-3-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rearrange the tjmax handling code so that it can be used directly in
the sysfs attribute callbacks without forward declarations.
No functional change in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221113153145.32696-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking for the valid bit of IA32_THERM_STATUS is removed in commit
bf6ea084eb ("hwmon: (coretemp) Do not return -EAGAIN for low
temperatures"), and temp_data->valid is set and never cleared when the
temperature has been read once.
Remove the obsolete temp_data->valid field.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221108075051.5139-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading
and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and
they can be told appart only by the boot cpu vendor (Intel/AMD).
Currently only AMD boards are supported since Intel have different EC
registers and values to read/write.
Fan control is provided via pwm interface in the range [0-255]. AMD
boards have [0-100] as range in the EC, the written value is scaled to
accommodate for that.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com
[groeck: Removed misleading comment about module_platform_driver()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorganize macro definitions into sections for each supported
device, with additional comments on their purpose. This should
make it easier to follow what report each offset is coming
from. Also, reformat per-device initializations in
aqc_probe() to organize them into sections (fan info,
temp sensors, other parameters and lastly labels).
No functional changes.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20221107142455.655998-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add in DMI matching table to match various board quirks and settings.
This will be useful for future extentions, but will start with the
existing definition of the Shuttle SN68PT.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20221105232531.1619387-1-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use BIT() and GENMASK() macros for defining the bitfields inside the
registers. Also use FIELD_GET() and FIELD_PREP() where appropriate. This
makes the coding style within the driver consistent. No functional
changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC7132.
The relevant registers in the LTC7132 are identical to the LTC7880.
So it's just a matter of adding the chip id.
Signed-off-by: Felix Nieuwenhuizen <Felix.Nieuwenhuizen@etas.com>
Link: https://lore.kernel.org/r/20221027145135.31802-1-Felix.Nieuwenhuizen@etas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang warns:
drivers/hwmon/smpro-hwmon.c:378:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
default:
^
drivers/hwmon/smpro-hwmon.c:378:2: note: insert 'break;' to avoid fall-through
default:
^
break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return.
Add the missing break to silence the warning. Additionally, adjust the
indentation of a break and add a default case to the inner switch
statement.
Fixes: a87456864cbb ("hwmon: Add Ampere's Altra smpro-hwmon driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1751
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20221027231611.3824800-1-nathan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the missing unlock before return from function jc42_write()
in the error handling case.
Fixes: 37dedaee8bc6 ("hwmon: (jc42) Convert register access and caching to regmap/regcache")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221027062931.598247-1-yangyingliang@huawei.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs
(using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer
0x104a, device 0x2201). It does not keep the previously programmed
minimum, maximum and critical temperatures after system suspend and
resume (which is a shutdown / startup cycle for the JC42 temperature
sensor). This results in an alarm on system resume because the hardware
default for these values is 0°C (so any environment temperature greater
than 0°C will trigger the alarm).
Example before system suspend:
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C)
(high = +85.0°C, hyst = +85.0°C)
(crit = +95.0°C, hyst = +95.0°C)
Example after system resume (without this change):
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C) ALARM (HIGH, CRIT)
(high = +0.0°C, hyst = +0.0°C)
(crit = +0.0°C, hyst = +0.0°C)
Apply the cached values from the JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where
the SMBUS register is not related to this issue but a side-effect of
using regcache_sync() during system resume with the previously
cached/programmed values. This fixes the alarm due to the hardware
defaults of 0°C because the previously applied limits (set by userspace)
are re-applied on system resume.
Fixes: 175c490c9e ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-3-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit c112d75840 ("hwmon: OCC drivers are ARM-only") made the OCC
sensor drivers not selectable on powerpc64:
These drivers are for a BMC inside PowerPC servers. The BMC runs on
ARM hardware, so only propose the drivers on this architecture, unless
build-testing.
... but we now have a powerpc64 BMC (still for a powerpc64 host), so
drop the `depends on` that excludes building for this platform.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221024081527.3842565-1-jk@codeconstruct.com.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds support for Ampere SMpro hwmon driver. This driver
supports accessing various CPU sensors provided by the SMpro co-processor
including temperature, power, voltages, and current.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20220929094321.770125-2-quan@os.amperecomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drop open-coded pattern: 'devm_regulator_get(), regulator_enable(),
add_action_or_reset(regulator_disable)' and use the
devm_regulator_get_enable() and drop the pointer to the regulator.
This simplifies code and makes it less tempting to add manual control
for the regulator which is also controlled by devm.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/7773541795f280db31dd981ffc21df8a630b794a.1666357434.git.mazziesaccount@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All these drivers have an i2c probe function which doesn't use the
"struct i2c_device_id *id" parameter, so they can trivially be
converted to the "probe_new" style of probe with a single argument.
This is part of an ongoing transition to single-argument i2c probe
functions. Old-style probe functions involve a call to i2c_match_id:
in drivers/i2c/i2c-core-base.c,
/*
* When there are no more users of probe(),
* rename probe_new to probe.
*/
if (driver->probe_new)
status = driver->probe_new(client);
else if (driver->probe)
status = driver->probe(client,
i2c_match_id(driver->id_table, client));
else
status = -EINVAL;
Drivers which don't need the second parameter can be declared using
probe_new instead, avoiding the call to i2c_match_id. Drivers which do
can still be converted to probe_new-style, calling i2c_match_id
themselves (as is done currently for of_match_id).
This change was done using the following Coccinelle script, and fixed
up for whitespace changes:
@ rule1 @
identifier fn;
identifier client, id;
@@
- static int fn(struct i2c_client *client, const struct i2c_device_id *id)
+ static int fn(struct i2c_client *client)
{
...when != id
}
@ rule2 depends on rule1 @
identifier rule1.fn;
identifier driver;
@@
struct i2c_driver driver = {
- .probe
+ .probe_new
=
(
fn
|
- &fn
+ fn
)
,
};
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20221011143309.3141267-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Check there is a chip before using force_id parameter as there
is no value in registering a non-existent chip
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20221004210100.540120-3-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add parameter to ignore ACPI resource conflicts as an alternate to using
'acpi_enforce_resources=lax'.
Some BIOSes reserve resources and don't use them and the system wide
parameter may result in failures to certain drivers.
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20221004210100.540120-2-ahmad@khalifa.ws
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate the read-only const arrays names and watchdog_minors
on the stack but instead make them static const. Also makes the
object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221005152752.318493-1-colin.i.king@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As the devm_kcalloc may return NULL, the return value needs to be checked
to avoid NULL poineter dereference.
Fixes: d0ddfd241e ("hwmon: (asus-ec-sensors) add driver for ASUS EC")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221125014329.121560-1-yuancan@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it after using to avoid refcount leak.
Fixes: 14513ee696 ("hwmon: (coretemp) Use PCI host bridge ID to identify CPU if necessary")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221118093303.214163-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For bus-based driver, device removal is implemented as:
1 device_remove()->
2 bus->remove()->
3 driver->remove()
Driver core needs no inform from callee(bus driver) about the
result of remove callback. In that case, commit fc7a6209d5
("bus: Make remove callback return void") forces bus_type::remove
be void-returned.
Now we have the situation that both 1 & 2 of calling chain are
void-returned, so it does not make much sense for 3(driver->remove)
to return non-void to its caller.
So the basic idea behind this change is making remove() callback of
any bus-based driver to be void-returned.
This change, for itself, is for device drivers based on acpi-bus.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for drivers/platform/surface/*
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Smatch report warning as follows:
drivers/hwmon/ibmpex.c:509 ibmpex_register_bmc() warn:
'&data->list' not removed from list
If ibmpex_find_sensors() fails in ibmpex_register_bmc(), data will
be freed, but data->list will not be removed from driver_data.bmc_data,
then list traversal may cause UAF.
Fix by removeing it from driver_data.bmc_data before free().
Fixes: 57c7c3a0fd ("hwmon: IBM power meter driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221117034423.2935739-1-cuigaosheng1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release().
Fixes: ada072816b ("hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221112125606.3751430-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt sum critical limit register value should be left shifted
by one bit as its LSB-0 is a reserved bit.
Fixes: 2057bdfb71 ("hwmon: (ina3221) Add summation feature support")
Signed-off-by: Ninad Malwade <nmalwade@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221108044508.23463-1-nmalwade@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC2947 datasheet (Rev. B) calls out in the section "Register
Description: Non-Accumulated Result Registers" (pg. 30) that "To
calculate temperature, multiply the TEMP register value by 0.204°C
and add 5.5°C". Fix to add 5.5C and not 0.55C.
Fixes: 9f90fd652b ("hwmon: Add support for ltc2947")
Signed-off-by: Derek Nguyen <derek.nguyen@collins.com>
Signed-off-by: Brandon Maier <brandon.maier@collins.com>
Link: https://lore.kernel.org/r/20221110192108.20624-1-brandon.maier@collins.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit 54cc3dbfc1.
Zev Weiss reports that the reverted patch may cause a regulator
undercount. Here is his report:
... having regulator-dummy set as a supply on my PMBus regulators
(instead of having them as their own top-level regulators without
an upstream supply) leads to enable-count underflow errors when
disabling them:
# echo 0 > /sys/bus/platform/devices/efuse01/state
[ 906.094477] regulator-dummy: Underflow of regulator enable count
[ 906.100563] Failed to disable vout: -EINVAL
[ 136.992676] reg-userspace-consumer efuse01: Failed to configure state: -22
Zev reports that reverting the patch fixes the problem. So let's do that
for now.
Fixes: 54cc3dbfc1 ("hwmon: (pmbus) Add regulator supply into macro")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Reported-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Available sensors are enumerated and reported by the SCMI platform server
using a 16bit identification number; not all such sensors are of a type
supported by hwmon subsystem and, among the supported ones, only a subset
could be temperature sensors that have to be registered with the Thermal
Framework.
Potential clashes between hwmon channels indexes and the underlying real
sensors IDs do not play well with the hwmon<-->thermal bridge automatic
registration routines and could need a sensible number of fake dummy
sensors to be made up in order to keep indexes and IDs in sync.
Avoid to use the hwmon<-->thermal bridge dropping the HWMON_C_REGISTER_TZ
attribute and instead explicit register temperature sensors directly with
the Thermal Framework.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20221031114018.59048-1-cristian.marussi@arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache allocation
on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration info
properly
- Drop a -mabi=ms compiler option check as both compilers support it now
anyway
- A couple of fixes to how the initial, statically allocated FPU buffer
state is setup and its interaction with dynamic states at runtime
-----BEGIN PGP SIGNATURE-----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=2hxy
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"As usually the case, right after a major release, the tip urgent
branches accumulate a couple more fixes than normal. And here is the
x86, a bit bigger, urgent pile.
- Use the correct CPU capability clearing function on the error path
in Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache
allocation on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration
info properly
- Drop a -mabi=ms compiler option check as both compilers support it
now anyway
- A couple of fixes to how the initial, statically allocated FPU
buffer state is setup and its interaction with dynamic states at
runtime"
* tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Fix copy_xstate_to_uabi() to copy init states correctly
perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
ftrace,kcfi: Separate ftrace_stub() and ftrace_stub_graph()
x86/ftrace: Remove ftrace_epilogue()
x86/resctrl: Fix min_cbm_bits for AMD
x86/microcode/AMD: Apply the patch early on every logical thread
x86/topology: Fix duplicated core ID within a package
x86/topology: Fix multiple packages shown on a single-package system
hwmon/coretemp: Handle large core ID value
x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
x86/fpu: Exclude dynamic states from init_fpstate
x86/fpu: Fix the init_fpstate size check with the actual size
x86/fpu: Configure init_fpstate attributes orderly
The coretemp driver supports up to a hard-coded limit of 128 cores.
Today, the driver can not support a core with an ID above that limit.
Yet, the encoding of core ID's is arbitrary (BIOS APIC-ID) and so they
may be sparse and they may be large.
Update the driver to map arbitrary core ID numbers into appropriate
array indexes so that 128 cores can be supported, no matter the encoding
of core ID's.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20221014090147.1836-3-rui.zhang@intel.com
