8142bd82a5
825227 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
David S. Miller
|
cb8075d934 |
Merge branch 'ks8851-fixes'
Lukas Wunner says: ==================== ks8851 fixes & cleanups Four fixes and two cleanups for the Microchip (formerly Micrel) KSZ8851 SPI Ethernet driver. Some of the fixes might even pass as stable material, but I haven't marked them as such for cautiousness: Doesn't hurt letting them bake in linux-next for a few weeks to raise the confidence, even though we've tested them extensively on our Revolution Pi open source PLCs. ==================== Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Lukas Wunner
|
aae079aa76 |
net: ks8851: Deduplicate register macros
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or with a so-called non-PCI interface (KSZ8851-16MLL). When the driver for the latter was introduced with commit |
||
|
Lukas Wunner
|
cbda74a12c |
net: ks8851: Fix register macro misnomers
In the header file accompanying the ks8851 driver, the P1SCLMD register macros are misnamed, they actually pertain to the P1CR register. The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68 of the spec: http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf The misnomers have no negative consequences so far because the macros aren't used by ks8851.c, but that's about to change. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Lukas Wunner
|
9624bafa5f |
net: ks8851: Set initial carrier state to down
The ks8851 chip's initial carrier state is down. A Link Change Interrupt is signaled once interrupts are enabled if the carrier is up. The ks8851 driver has it backwards by assuming that the initial carrier state is up. The state is therefore misrepresented if the interface is opened with no cable attached. Fix it. The Link Change interrupt is sometimes not signaled unless the P1MBSR register (which contains the Link Status bit) is read on ->ndo_open(). This might be a hardware erratum. Read the register by calling mii_check_link(), which has the desirable side effect of setting the carrier state to down if the cable was detached while the interface was closed. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Lukas Wunner
|
d268f31552 |
net: ks8851: Delay requesting IRQ until opened
The ks8851 driver currently requests the IRQ before registering the net_device. Because the net_device name is used as IRQ name and is still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs apart if multiple ks8851 chips are present. Most other drivers delay requesting the IRQ until the net_device is opened. Do the same. The driver doesn't enable interrupts on the chip before opening the net_device and disables them when closing it, so there doesn't seem to be a need to request the IRQ already on probe. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Lukas Wunner
|
761cfa979a |
net: ks8851: Reassert reset pin if chip ID check fails
Commit
|
||
|
Lukas Wunner
|
536d3680fd |
net: ks8851: Dequeue RX packets explicitly
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
Song Liu
|
6987561c9e |
perf annotate: Enable annotation of BPF programs
In symbol__disassemble(), DSO_BINARY_TYPE__BPF_PROG_INFO dso calls into
a new function symbol__disassemble_bpf(), where annotation line
information is filled based on the bpf_prog_info and btf data saved in
given perf_env.
symbol__disassemble_bpf() uses binutils's libopcodes to disassemble bpf
programs.
Committer testing:
After fixing this:
- u64 *addrs = (u64 *)(info_linear->info.jited_ksyms);
+ u64 *addrs = (u64 *)(uintptr_t)(info_linear->info.jited_ksyms);
Detected when crossbuilding to a 32-bit arch.
And making all this dependent on HAVE_LIBBFD_SUPPORT and
HAVE_LIBBPF_SUPPORT:
1) Have a BPF program running, one that has BTF info, etc, I used
the tools/perf/examples/bpf/augmented_raw_syscalls.c put in place
by 'perf trace'.
# grep -B1 augmented_raw ~/.perfconfig
[trace]
add_events = /home/acme/git/perf/tools/perf/examples/bpf/augmented_raw_syscalls.c
#
# perf trace -e *mmsg
dnf/6245 sendmmsg(20, 0x7f5485a88030, 2, MSG_NOSIGNAL) = 2
NetworkManager/10055 sendmmsg(22<socket:[1056822]>, 0x7f8126ad1bb0, 2, MSG_NOSIGNAL) = 2
2) Then do a 'perf record' system wide for a while:
# perf record -a
^C[ perf record: Woken up 68 times to write data ]
[ perf record: Captured and wrote 19.427 MB perf.data (366891 samples) ]
#
3) Check that we captured BPF and BTF info in the perf.data file:
# perf report --header-only | grep 'b[pt]f'
# event : name = cycles:ppp, , id = { 294789, 294790, 294791, 294792, 294793, 294794, 294795, 294796 }, size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|CPU|PERIOD, read_format = ID, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1, ksymbol = 1, bpf_event = 1
# bpf_prog_info of id 13
# bpf_prog_info of id 14
# bpf_prog_info of id 15
# bpf_prog_info of id 16
# bpf_prog_info of id 17
# bpf_prog_info of id 18
# bpf_prog_info of id 21
# bpf_prog_info of id 22
# bpf_prog_info of id 41
# bpf_prog_info of id 42
# btf info of id 2
#
4) Check which programs got recorded:
# perf report | grep bpf_prog | head
0.16% exe bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.14% exe bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.08% fuse-overlayfs bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.07% fuse-overlayfs bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.01% clang-4.0 bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.01% clang-4.0 bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.00% clang bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.00% runc bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.00% clang bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.00% sh bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
#
This was with the default --sort order for 'perf report', which is:
--sort comm,dso,symbol
If we just look for the symbol, for instance:
# perf report --sort symbol | grep bpf_prog | head
0.26% [k] bpf_prog_819967866022f1e1_sys_enter - -
0.24% [k] bpf_prog_c1bd85c092d6e4aa_sys_exit - -
#
or the DSO:
# perf report --sort dso | grep bpf_prog | head
0.26% bpf_prog_819967866022f1e1_sys_enter
0.24% bpf_prog_c1bd85c092d6e4aa_sys_exit
#
We'll see the two BPF programs that augmented_raw_syscalls.o puts in
place, one attached to the raw_syscalls:sys_enter and another to the
raw_syscalls:sys_exit tracepoints, as expected.
Now we can finally do, from the command line, annotation for one of
those two symbols, with the original BPF program source coude intermixed
with the disassembled JITed code:
# perf annotate --stdio2 bpf_prog_819967866022f1e1_sys_enter
Samples: 950 of event 'cycles:ppp', 4000 Hz, Event count (approx.): 553756947, [percent: local period]
bpf_prog_819967866022f1e1_sys_enter() bpf_prog_819967866022f1e1_sys_enter
Percent int sys_enter(struct syscall_enter_args *args)
53.41 push %rbp
0.63 mov %rsp,%rbp
0.31 sub $0x170,%rsp
1.93 sub $0x28,%rbp
7.02 mov %rbx,0x0(%rbp)
3.20 mov %r13,0x8(%rbp)
1.07 mov %r14,0x10(%rbp)
0.61 mov %r15,0x18(%rbp)
0.11 xor %eax,%eax
1.29 mov %rax,0x20(%rbp)
0.11 mov %rdi,%rbx
return bpf_get_current_pid_tgid();
2.02 → callq *ffffffffda6776d9
2.76 mov %eax,-0x148(%rbp)
mov %rbp,%rsi
int sys_enter(struct syscall_enter_args *args)
add $0xfffffffffffffeb8,%rsi
return bpf_map_lookup_elem(pids, &pid) != NULL;
movabs $0xffff975ac2607800,%rdi
1.26 → callq *ffffffffda6789e9
cmp $0x0,%rax
2.43 → je 0
add $0x38,%rax
0.21 xor %r13d,%r13d
if (pid_filter__has(&pids_filtered, getpid()))
0.81 cmp $0x0,%rax
→ jne 0
mov %rbp,%rdi
probe_read(&augmented_args.args, sizeof(augmented_args.args), args);
2.22 add $0xfffffffffffffeb8,%rdi
0.11 mov $0x40,%esi
0.32 mov %rbx,%rdx
2.74 → callq *ffffffffda658409
syscall = bpf_map_lookup_elem(&syscalls, &augmented_args.args.syscall_nr);
0.22 mov %rbp,%rsi
1.69 add $0xfffffffffffffec0,%rsi
syscall = bpf_map_lookup_elem(&syscalls, &augmented_args.args.syscall_nr);
movabs $0xffff975bfcd36000,%rdi
add $0xd0,%rdi
0.21 mov 0x0(%rsi),%eax
0.93 cmp $0x200,%rax
→ jae 0
0.10 shl $0x3,%rax
0.11 add %rdi,%rax
0.11 → jmp 0
xor %eax,%eax
if (syscall == NULL || !syscall->enabled)
1.07 cmp $0x0,%rax
→ je 0
if (syscall == NULL || !syscall->enabled)
6.57 movzbq 0x0(%rax),%rdi
if (syscall == NULL || !syscall->enabled)
cmp $0x0,%rdi
0.95 → je 0
mov $0x40,%r8d
switch (augmented_args.args.syscall_nr) {
mov -0x140(%rbp),%rdi
switch (augmented_args.args.syscall_nr) {
cmp $0x2,%rdi
→ je 0
cmp $0x101,%rdi
→ je 0
cmp $0x15,%rdi
→ jne 0
case SYS_OPEN: filename_arg = (const void *)args->args[0];
mov 0x10(%rbx),%rdx
→ jmp 0
case SYS_OPENAT: filename_arg = (const void *)args->args[1];
mov 0x18(%rbx),%rdx
if (filename_arg != NULL) {
cmp $0x0,%rdx
→ je 0
xor %edi,%edi
augmented_args.filename.reserved = 0;
mov %edi,-0x104(%rbp)
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov %rbp,%rdi
add $0xffffffffffffff00,%rdi
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov $0x100,%esi
→ callq *ffffffffda658499
mov $0x148,%r8d
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov %eax,-0x108(%rbp)
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov %rax,%rdi
shl $0x20,%rdi
shr $0x20,%rdi
if (augmented_args.filename.size < sizeof(augmented_args.filename.value)) {
cmp $0xff,%rdi
→ ja 0
len -= sizeof(augmented_args.filename.value) - augmented_args.filename.size;
add $0x48,%rax
len &= sizeof(augmented_args.filename.value) - 1;
and $0xff,%rax
mov %rax,%r8
mov %rbp,%rcx
return perf_event_output(args, &__augmented_syscalls__, BPF_F_CURRENT_CPU, &augmented_args, len);
add $0xfffffffffffffeb8,%rcx
mov %rbx,%rdi
movabs $0xffff975fbd72d800,%rsi
mov $0xffffffff,%edx
→ callq *ffffffffda658ad9
mov %rax,%r13
}
mov %r13,%rax
0.72 mov 0x0(%rbp),%rbx
mov 0x8(%rbp),%r13
1.16 mov 0x10(%rbp),%r14
0.10 mov 0x18(%rbp),%r15
0.42 add $0x28,%rbp
0.54 leaveq
0.54 ← retq
#
Please see 'man perf-config' to see how to control what should be seen,
via ~/.perfconfig [annotate] section, for instance, one can suppress the
source code and see just the disassembly, etc.
Alternatively, use the TUI bu just using 'perf annotate', press
'/bpf_prog' to see the bpf symbols, press enter and do the interactive
annotation, which allows for dumping to a file after selecting the
the various output tunables, for instance, the above without source code
intermixed, plus showing all the instruction offsets:
# perf annotate bpf_prog_819967866022f1e1_sys_enter
Then press: 's' to hide the source code + 'O' twice to show all
instruction offsets, then 'P' to print to the
bpf_prog_819967866022f1e1_sys_enter.annotation file, which will have:
# cat bpf_prog_819967866022f1e1_sys_enter.annotation
bpf_prog_819967866022f1e1_sys_enter() bpf_prog_819967866022f1e1_sys_enter
Event: cycles:ppp
53.41 0: push %rbp
0.63 1: mov %rsp,%rbp
0.31 4: sub $0x170,%rsp
1.93 b: sub $0x28,%rbp
7.02 f: mov %rbx,0x0(%rbp)
3.20 13: mov %r13,0x8(%rbp)
1.07 17: mov %r14,0x10(%rbp)
0.61 1b: mov %r15,0x18(%rbp)
0.11 1f: xor %eax,%eax
1.29 21: mov %rax,0x20(%rbp)
0.11 25: mov %rdi,%rbx
2.02 28: → callq *ffffffffda6776d9
2.76 2d: mov %eax,-0x148(%rbp)
33: mov %rbp,%rsi
36: add $0xfffffffffffffeb8,%rsi
3d: movabs $0xffff975ac2607800,%rdi
1.26 47: → callq *ffffffffda6789e9
4c: cmp $0x0,%rax
2.43 50: → je 0
52: add $0x38,%rax
0.21 56: xor %r13d,%r13d
0.81 59: cmp $0x0,%rax
5d: → jne 0
63: mov %rbp,%rdi
2.22 66: add $0xfffffffffffffeb8,%rdi
0.11 6d: mov $0x40,%esi
0.32 72: mov %rbx,%rdx
2.74 75: → callq *ffffffffda658409
0.22 7a: mov %rbp,%rsi
1.69 7d: add $0xfffffffffffffec0,%rsi
84: movabs $0xffff975bfcd36000,%rdi
8e: add $0xd0,%rdi
0.21 95: mov 0x0(%rsi),%eax
0.93 98: cmp $0x200,%rax
9f: → jae 0
0.10 a1: shl $0x3,%rax
0.11 a5: add %rdi,%rax
0.11 a8: → jmp 0
aa: xor %eax,%eax
1.07 ac: cmp $0x0,%rax
b0: → je 0
6.57 b6: movzbq 0x0(%rax),%rdi
bb: cmp $0x0,%rdi
0.95 bf: → je 0
c5: mov $0x40,%r8d
cb: mov -0x140(%rbp),%rdi
d2: cmp $0x2,%rdi
d6: → je 0
d8: cmp $0x101,%rdi
df: → je 0
e1: cmp $0x15,%rdi
e5: → jne 0
e7: mov 0x10(%rbx),%rdx
eb: → jmp 0
ed: mov 0x18(%rbx),%rdx
f1: cmp $0x0,%rdx
f5: → je 0
f7: xor %edi,%edi
f9: mov %edi,-0x104(%rbp)
ff: mov %rbp,%rdi
102: add $0xffffffffffffff00,%rdi
109: mov $0x100,%esi
10e: → callq *ffffffffda658499
113: mov $0x148,%r8d
119: mov %eax,-0x108(%rbp)
11f: mov %rax,%rdi
122: shl $0x20,%rdi
126: shr $0x20,%rdi
12a: cmp $0xff,%rdi
131: → ja 0
133: add $0x48,%rax
137: and $0xff,%rax
13d: mov %rax,%r8
140: mov %rbp,%rcx
143: add $0xfffffffffffffeb8,%rcx
14a: mov %rbx,%rdi
14d: movabs $0xffff975fbd72d800,%rsi
157: mov $0xffffffff,%edx
15c: → callq *ffffffffda658ad9
161: mov %rax,%r13
164: mov %r13,%rax
0.72 167: mov 0x0(%rbp),%rbx
16b: mov 0x8(%rbp),%r13
1.16 16f: mov 0x10(%rbp),%r14
0.10 173: mov 0x18(%rbp),%r15
0.42 177: add $0x28,%rbp
0.54 17b: leaveq
0.54 17c: ← retq
Another cool way to test all this is to symple use 'perf top' look for
those symbols, go there and press enter, annotate it live :-)
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
||
|
Song Liu
|
8a1b171821 |
perf build: Check what binutils's 'disassembler()' signature to use
Commit 003ca0fd2286 ("Refactor disassembler selection") in the binutils
repo, which changed the disassembler() function signature, so we must
use the feature test introduced in
|
||
Filipe Manana
|
0ccc3876e4 |
Btrfs: fix assertion failure on fsync with NO_HOLES enabled
Back in commit |
||
Luo Jiaxing
|
0e83fc61ee |
scsi: hisi_sas: Add softreset in hisi_sas_I_T_nexus_reset()
We found out that for v2 hw, a SATA disk can not be written to after the system comes up. In commit |
||
Rasmus Villemoes
|
89dc891792 |
irqchip/gic-v3-its: Fix comparison logic in lpi_range_cmp
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes:
|
||
Xin Long
|
ef82bcfa67 |
sctp: use memdup_user instead of vmemdup_user
In sctp_setsockopt_bindx()/__sctp_setsockopt_connectx(), it allocates memory with addrs_size which is passed from userspace. We used flag GFP_USER to put some more restrictions on it in Commit |
||
|
Xin Long
|
1c87e79a00 |
ipv6: make ip6_create_rt_rcu return ip6_null_entry instead of NULL
Jianlin reported a crash:
[ 381.484332] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
[ 381.619802] RIP: 0010:fib6_rule_lookup+0xa3/0x160
[ 382.009615] Call Trace:
[ 382.020762] <IRQ>
[ 382.030174] ip6_route_redirect.isra.52+0xc9/0xf0
[ 382.050984] ip6_redirect+0xb6/0xf0
[ 382.066731] icmpv6_notify+0xca/0x190
[ 382.083185] ndisc_redirect_rcv+0x10f/0x160
[ 382.102569] ndisc_rcv+0xfb/0x100
[ 382.117725] icmpv6_rcv+0x3f2/0x520
[ 382.133637] ip6_input_finish+0xbf/0x460
[ 382.151634] ip6_input+0x3b/0xb0
[ 382.166097] ipv6_rcv+0x378/0x4e0
It was caused by the lookup function __ip6_route_redirect() returns NULL in
fib6_rule_lookup() when ip6_create_rt_rcu() returns NULL.
So we fix it by simply making ip6_create_rt_rcu() return ip6_null_entry
instead of NULL.
v1->v2:
- move down 'fallback:' to make it more readable.
Fixes:
|
||
Linus Torvalds
|
54c4901645 |
ARC updates for 5.1-rc2
- unaligned access support for HS cores - Removed extra memory barrier around spinlock code - HSDK platform updates: enable dmac, reset - some more boot logging updates - misclleneous minor fixes -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJckWU3AAoJEGnX8d3iisJeh9sP/jAu5RP5lrDbxXsEC9MX5WSB 8s+Ja77Nx3f6XfEv/Ii+cnYMxTXpdvYMt3YePsP/9oelNzzkoPWb6PmkGdEYcof/ IXDvtEsCdF7qoi6MEWeADIbUsZSxF9ZDJfCirPptOOWWEi34gApkoyjbSNwipNRv ZEUWBlc7nURbEFR4Gly0qB+JFuIJbpw8g7T8qU835jQiJ4f6O4y+Etx5YGc3k1B8 9WU0Wl8Dog358lqHdcCFsymRlCIqTGZ9h/HAO1QIco2q9BYHzjR1koPks9WlYMBs p0q3k2Pquhathb04HFXwQxCfXpaRUw1jJ4WR8hGTKHedywMsvnfiaODZKHxIQiMM E451oGfVQO4NcVEVvlWlpkCYlZVYgq9O1YBIAB/KKy5O9TlmcRzKJijLKEw+tpaF 7djp+n+xVf3jeB77/feH8ryuqjaJklA5Zb+1gPt4lD8zJgzmpQ7cmtHOIVmroB6Q VTt35Of7SX131pF3HPdMcbx6Cvjs61pox33miR5k9qbkq07M8zCtFneoX9bJV5k3 Fu7qFU/M2d/EQwnsavh6nURfePWIcd/c4rayIRFEye8oRX8mvpi5mHhP0wVz0D1R 1eIWulI4xisNZo3kWOnhgCdLSFFsn+K4YdQu73PGdFqFDjs6ltgsTYolVKSCDQFq XTZoIXmArVYvMWkAl3pq =fFs9 -----END PGP SIGNATURE----- Merge tag 'arc-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc Pull ARC updates from Vineet Gupta: - unaligned access support for HS cores - Removed extra memory barrier around spinlock code - HSDK platform updates: enable dmac, reset - some more boot logging updates - misc minor fixes * tag 'arc-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: arch: arc: Kconfig: pedantic formatting ARCv2: spinlock: remove the extra smp_mb before lock, after unlock ARC: unaligned: relax the check for gcc supporting -mno-unaligned-access ARC: boot log: cut down on verbosity ARCv2: boot log: refurbish HS core/release identification arc: hsdk_defconfig: Enable CONFIG_BLK_DEV_RAM ARC: u-boot args: check that magic number is correct ARC: perf: bpok condition only exists for ARCompact ARCv2: Add explcit unaligned access support (and ability to disable too) ARCv2: lib: introduce memcpy optimized for unaligned access ARC: [plat-hsdk]: Enable AXI DW DMAC support ARC: [plat-hsdk]: Add reset controller handle to manage USB reset ARC: DTB: [scripted] fix node name and address spelling |
||
Christoph Paasch
|
398f0132c1 |
net/packet: Set __GFP_NOWARN upon allocation in alloc_pg_vec
Since commit |
||
Matthias Kaehlcke
|
e5a5af7718 |
arm64: remove obsolete selection of MULTI_IRQ_HANDLER
The arm64 config selects MULTI_IRQ_HANDLER, which was renamed to
GENERIC_IRQ_MULTI_HANDLER by commit
|
||
Ilya Dryomov
|
9d4a227f6e |
rbd: drop wait_for_latest_osdmap()
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jason Dillaman <dillaman@redhat.com> |
||
|
Ilya Dryomov
|
bb229bbb3b |
libceph: wait for latest osdmap in ceph_monc_blacklist_add()
Because map updates are distributed lazily, an OSD may not know about
the new blacklist for quite some time after "osd blacklist add" command
is completed. This makes it possible for a blacklisted but still alive
client to overwrite a post-blacklist update, resulting in data
corruption.
Waiting for latest osdmap in ceph_monc_blacklist_add() and thus using
the post-blacklist epoch for all post-blacklist requests ensures that
all such requests "wait" for the blacklist to come into force on their
respective OSDs.
Cc: stable@vger.kernel.org
Fixes:
|
||
Ben Hutchings
|
8bc0868998 |
powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations
MAX_PHYSMEM_BITS only needs to be defined if CONFIG_SPARSEMEM is enabled, and that was the case before commit |
||
Marco Felsch
|
032f85c936 |
ARM: dts: pfla02: increase phy reset duration
Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes:
|
||
Taehee Yoo
|
b25a31bf0c |
netfilter: nf_tables: add missing ->release_ops() in error path of newrule()
->release_ops() callback releases resources and this is used in error path.
If nf_tables_newrule() fails after ->select_ops(), it should release
resources. but it can not call ->destroy() because that should be called
after ->init().
At this point, ->release_ops() should be used for releasing resources.
Test commands:
modprobe -rv xt_tcpudp
iptables-nft -I INPUT -m tcp <-- error command
lsmod
Result:
Module Size Used by
xt_tcpudp 20480 2 <-- it should be 0
Fixes:
|
||
Thomas Zimmermann
|
c2d3115538 |
drm/vmwgfx: Don't double-free the mode stored in par->set_mode
When calling vmw_fb_set_par(), the mode stored in par->set_mode gets free'd
twice. The first free is in vmw_fb_kms_detach(), the second is near the
end of vmw_fb_set_par() under the name of 'old_mode'. The mode-setting code
only works correctly if the mode doesn't actually change. Removing
'old_mode' in favor of using par->set_mode directly fixes the problem.
Cc: <stable@vger.kernel.org>
Fixes:
|
||
Deepak Rawat
|
4b9ce3a651 |
drm/vmwgfx: Return 0 when gmrid::get_node runs out of ID's
If it's not a system error and get_node implementation accommodate the
buffer object then it should return 0 with memm::mm_node set to NULL.
v2: Test for id != -ENOMEM instead of id == -ENOSPC.
Cc: <stable@vger.kernel.org>
Fixes:
|
||
Vinay K Nallamothu
|
f84532ce58 |
mpls: Fix 6PE forwarding
This patch adds support for 6PE (RFC 4798) which uses IPv4-mapped IPv6
nexthop to connect IPv6 islands over IPv4 only MPLS network core.
Prior to this fix, to find the link-layer destination mac address, 6PE
enabled host/router was sending IPv6 ND requests for IPv4-mapped IPv6
nexthop address over the interface facing the IPv4 only core which
wouldn't success as the core is IPv6 free.
This fix changes that behavior on 6PE host to treat the nexthop as IPv4
address and send ARP requests whenever the next-hop address is an
IPv4-mapped IPv6 address.
Below topology illustrates the issue and how the patch addresses it.
abcd::1.1.1.1 (lo) abcd::2.2.2.2 (lo)
R0 (PE/host)------------------------R1--------------------------------R2 (PE/host)
<--- IPv4 MPLS core ---> <------ IPv4 MPLS core -------->
eth1 eth2 eth3 eth4
172.18.0.10 172.18.0.11 172.19.0.11 172.19.0.12
ffff::172.18.0.10 ffff::172.19.0.12
<------------------IPv6 MPLS tunnel ---------------------->
R0 and R2 act as 6PE routers of IPv6 islands. R1 is IPv4 only with MPLS tunnels
between R0,R1 and R1,R2.
docker exec r0 ip -f inet6 route add abcd::2.2.2.2/128 nexthop encap mpls 100 via ::ffff:172.18.0.11 dev eth1
docker exec r2 ip -f inet6 route add abcd::1.1.1.1/128 nexthop encap mpls 200 via ::ffff:172.19.0.11 dev eth4
docker exec r1 ip -f mpls route add 100 via inet 172.19.0.12 dev eth3
docker exec r1 ip -f mpls route add 200 via inet 172.18.0.10 dev eth2
With the change, when R0 sends an IPv6 packet over MPLS tunnel to abcd::2.2.2.2,
using ::ffff:172.18.0.11 as the nexthop, it does neighbor discovery for
172.18.18.0.11.
Signed-off-by: Vinay K Nallamothu <nvinay@juniper.net>
Tested-by: Avinash Lingala <ar977m@att.com>
Tested-by: Aravind Srinivas Srinivasa Prabhakar <aprabh@juniper.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
Arnd Bergmann
|
fb6fafbc7d |
3c515: fix integer overflow warning
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
Jiada Wang
|
2071ac985d |
PM / Domains: Avoid a potential deadlock
Lockdep warns that prepare_lock and genpd->mlock can cause a deadlock
the deadlock scenario is like following:
First thread is probing cs2000
cs2000_probe()
clk_register()
__clk_core_init()
clk_prepare_lock() ----> acquires prepare_lock
cs2000_recalc_rate()
i2c_smbus_read_byte_data()
rcar_i2c_master_xfer()
dma_request_chan()
rcar_dmac_of_xlate()
rcar_dmac_alloc_chan_resources()
pm_runtime_get_sync()
__pm_runtime_resume()
rpm_resume()
rpm_callback()
genpd_runtime_resume() ----> acquires genpd->mlock
Second thread is attaching any device to the same PM domain
genpd_add_device()
genpd_lock() ----> acquires genpd->mlock
cpg_mssr_attach_dev()
of_clk_get_from_provider()
__of_clk_get_from_provider()
__clk_create_clk()
clk_prepare_lock() ----> acquires prepare_lock
Since currently no PM provider access genpd's critical section
in .attach_dev, and .detach_dev callbacks, so there is no need to protect
these two callbacks with genpd->mlock.
This patch avoids a potential deadlock by moving out .attach_dev and .detach_dev
from genpd->mlock, so that genpd->mlock won't be held when prepare_lock is acquired
in .attach_dev and .detach_dev
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
||
Andy Shevchenko
|
54e3aca84e |
ACPI / utils: Drop reference in test for device presence
When commit |
||
Eric Dumazet
|
e0aa67709f |
dccp: do not use ipv6 header for ipv4 flow
When a dual stack dccp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or
inet6_iif() helper.
Fixes:
|
||
|
Eric Dumazet
|
89e4130939 |
tcp: do not use ipv6 header for ipv4 flow
When a dual stack tcp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or tcp_v6_iif() helper. Fixes: |
||
Aditya Pakki
|
d7737d4257 |
nfc: Fix to check for kmemdup failure
In case of kmemdup failure while setting the service name the patch returns -ENOMEM upstream for processing. Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
YueHaibing
|
a3e23f719f |
net-sysfs: call dev_hold if kobject_init_and_add success
In netdev_queue_add_kobject and rx_queue_add_kobject,
if sysfs_create_group failed, kobject_put will call
netdev_queue_release to decrease dev refcont, however
dev_hold has not be called. So we will see this while
unregistering dev:
unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
|
||
Aaro Koskinen
|
223a960c01 |
net: stmmac: fix memory corruption with large MTUs
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes:
|
||
|
Arnd Bergmann
|
7442c483b9 |
mlxsw: core: mlxsw: core: avoid -Wint-in-bool-context warning
A recently added function in mlxsw triggers a harmless compiler warning:
In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17,
from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7:
drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get':
drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
#define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125)
~~~~~^~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC'
if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) {
^~~~~~~~~~~~~~~~~~~~~~~~~
The warning is normally disabled, but it would be nice to enable
it to find real bugs, and there are no other known instances at
the moment.
Replace the negation with a zero-comparison, which also matches
the comment above it.
Fixes:
|
||
Florian Fainelli
|
9c05d4c33d |
This pull request brings in a fix for detecting HDMI on the Pi B rev 2.
-----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEE/JuuFDWp9/ZkuCBXtdYpNtH8nugFAlx9u1IACgkQtdYpNtH8 nuj4GQ/+PD3lP/InAK2+k/Fhas2IA+YjPIC+fbv6lZ1XA/DEXucK0k8RWQCp/vr3 cvHEB3QBmNyHDUJEKafHrozXzheI08OBWw/XbSarJb++dYz+AK+7bVucqLO8nRpU E7J/onHXpubcaWyw3Bt6e28WeOuK8LAZEqDsMtlge2B4ffAeCkQ2QQXd8ypkEIhg 00L0naqptigKXeDYdm40L/pko4NSNMrV98spLBn+Xe2dB+BcIRv9ZdwtCuZCnAKx pxGL0JNdXINRlvj+ySmu5WdkqRDfYF4b2voV7pSE36RTPeLKQAGaAOIEjrBnSYqj rQ3FABCNSu6DsEjVewO1KRA83pN0+KyE+GcAmz4xhPMgEbFlgT9tbj3E5a09Go/z qtH5HzB/K1kqcZqFBY9P1YFw7/0pRdzVl0J1qD2ACinTC8IghKCpOzcVENWraT1z XyVHJdkmH5VwBdkNSPf5V071v20zXVK8uNe+1l7bvaXInGTF/HqFfNXrf1QGnrtX 38HoNJ3wx8WjCSkJANz6GDpVSC8Z6VWmkW09IoZrzR+gHxqdzUDU0fbCoPuI/oAa TxwCEMWOqw0SYuly7Xd+jl4o0elG9lpefEYEHEcN2iku57aP8c1MTBxpo5RUpE2O FafXCQgVJSXPmw+rnFN2Ci+4h56f4pATWI/6W/R43JgCxWbl4t4= =LnIu -----END PGP SIGNATURE----- gpgsig -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAlyRTcAACgkQh9CWnEQH BwTEaQ/+Plj1UZErYBoIhNiRLhwPh3rvD59H3ruflF8MdZueicyFAtNmJy4B0TBx GLKj0xrQ/EORe8MJzHPUc5Itz832w1+HKqbVCS+uDzIgsYbQPeTs11d2Q8WhQj0C VtzRd74w3N6UYW+Wq2OHwftzU/7YHUhBT2OFhALUqgfCXRyYZfWbE0HgW1nNWEiJ yczaakmU9y6fh6dAp+cdFjZoSRhAKL/9WVOltxsUNbiQHR4SLA1v21U9BHFC0sXf rzI725k2bTJsweHy/3QuDwZKBbG4dmcAHhq1f8N8ycjHM5iJ3Y+ASIFJMk3CVuhM 0tH6lTwQfqzGYvIT9e1l5JYaaVYj34ypFP6hR7hqW7Lr34YU3I6+tn5luhW46Snz 1xi/zjFqeQyPDa+jlfNJhtUV8uvmDtoX1p6viyySE2AEfmLh2isf0oLE8MEpwH4q /sSR6l0itw9D4Pbb9eMqx3Bqpc0UmTy/zQvA/eaHqUOtL117nrxeMme0mA/82Ms/ TM1dt+RSSzmAvoz/vY0CQCuyyItYQxk89mi2aOQBnbp5PotYBazmoMv57CJf6CVK RrGgGmpkKWC8N3h0mwnQ7WP4rk7n7x5i9W0/bhngqx4ZmJI318PmMVJb2YWasQJC eYpNr3rBH/BH3kuRFX0FjPkHdzNvYOVhil6VkaCtFoAGIcxrDNQ= =n/bC -----END PGP SIGNATURE----- Merge tag 'tags/bcm2835-dt-next-2019-03-04' into devicetree/fixes This pull request brings in a fix for detecting HDMI on the Pi B rev 2. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
||
|
Song Liu
|
3ca3877a97 |
perf bpf: Process PERF_BPF_EVENT_PROG_LOAD for annotation
This patch adds processing of PERF_BPF_EVENT_PROG_LOAD, which sets proper DSO type/id/etc of memory regions mapped to BPF programs to DSO_BINARY_TYPE__BPF_PROG_INFO. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: kernel-team@fb.com Link: http://lkml.kernel.org/r/20190312053051.2690567-14-songliubraving@fb.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
|
Song Liu
|
9b86d04d53 |
perf symbols: Introduce DSO_BINARY_TYPE__BPF_PROG_INFO
Introduce a new dso type DSO_BINARY_TYPE__BPF_PROG_INFO for BPF programs. In symbol__disassemble(), DSO_BINARY_TYPE__BPF_PROG_INFO dso will call into a new function symbol__disassemble_bpf() in an upcoming patch, where annotation line information is filled based bpf_prog_info and btf saved in given perf_env. Committer notes: Removed the unnamed union with 'bpf_prog' and 'cache' in 'struct dso', to fix this bug when exiting 'perf top': # perf top perf: Segmentation fault -------- backtrace -------- perf[0x5a785a] /lib64/libc.so.6(+0x385bf)[0x7fd68443c5bf] perf(rb_first+0x2b)[0x4d6eeb] perf(dso__delete+0xb7)[0x4dffb7] perf[0x4f9e37] perf(perf_session__delete+0x64)[0x504df4] perf(cmd_top+0x1957)[0x454467] perf[0x4aad18] perf(main+0x61c)[0x42ec7c] /lib64/libc.so.6(__libc_start_main+0xf2)[0x7fd684428412] perf(_start+0x2d)[0x42eead] # # addr2line -fe ~/bin/perf 0x4dffb7 dso_cache__free /home/acme/git/perf/tools/perf/util/dso.c:713 That is trying to access the dso->data.cache, and that is not used with BPF programs, so we end up accessing what is in bpf_prog.first_member, b00m. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: kernel-team@fb.com Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com [ split from a larger patch ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
|
Song Liu
|
31be9478ed |
perf feature detection: Add -lopcodes to feature-libbfd
Both libbfd and libopcodes are distributed with binutil-dev/devel. When libbfd is present, it is OK to assume that libopcodes also present. This has been a safe assumption for bpftool. This patch adds -lopcodes to perf/Makefile.config. libopcodes will be used in the next commit for BPF annotation. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: kernel-team@fb.com Link: http://lkml.kernel.org/r/20190312053051.2690567-12-songliubraving@fb.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
|
Song Liu
|
ee7a112fbc |
perf top: Add option --no-bpf-event
This patch adds option --no-bpf-event to 'perf top', which is the same
as the option of 'perf record'.
The following patches will use this option.
Committer testing:
# perf top -vv 2> /tmp/perf_event_attr.out
# cat /tmp/perf_event_attr.out
------------------------------------------------------------
perf_event_attr:
size 112
{ sample_period, sample_freq } 4000
sample_type IP|TID|TIME|CPU|PERIOD
read_format ID
disabled 1
inherit 1
mmap 1
comm 1
freq 1
task 1
precise_ip 3
sample_id_all 1
exclude_guest 1
mmap2 1
comm_exec 1
ksymbol 1
bpf_event 1
------------------------------------------------------------
#
After this patch:
# perf top --no-bpf-event -vv 2> /tmp/perf_event_attr.out
# cat /tmp/perf_event_attr.out
------------------------------------------------------------
perf_event_attr:
size 112
{ sample_period, sample_freq } 4000
sample_type IP|TID|TIME|CPU|PERIOD
read_format ID
disabled 1
inherit 1
mmap 1
comm 1
freq 1
task 1
precise_ip 3
sample_id_all 1
exclude_guest 1
mmap2 1
comm_exec 1
ksymbol 1
------------------------------------------------------------
#
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-11-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
||
|
Song Liu
|
a70a112317 |
perf bpf: Save BTF information as headers to perf.data
This patch enables 'perf record' to save BTF information as headers to
perf.data.
A new header type HEADER_BPF_BTF is introduced for this data.
Committer testing:
As root, being on the kernel sources top level directory, run:
# perf trace -e tools/perf/examples/bpf/augmented_raw_syscalls.c -e *msg
Just to compile and load a BPF program that attaches to the
raw_syscalls:sys_{enter,exit} tracepoints to trace the syscalls ending
in "msg" (recvmsg, sendmsg, recvmmsg, sendmmsg, etc).
Make sure you have a recent enough clang, say version 9, to get the
BTF ELF sections needed for this testing:
# clang --version | head -1
clang version 9.0.0 (https://git.llvm.org/git/clang.git/ 7906282d3afec5dfdc2b27943fd6c0309086c507) (https://git.llvm.org/git/llvm.git/ a1b5de1ff8ae8bc79dc8e86e1f82565229bd0500)
# readelf -SW tools/perf/examples/bpf/augmented_raw_syscalls.o | grep BTF
[22] .BTF PROGBITS 0000000000000000 000ede 000b0e 00 0 0 1
[23] .BTF.ext PROGBITS 0000000000000000 0019ec 0002a0 00 0 0 1
[24] .rel.BTF.ext REL 0000000000000000 002fa8 000270 10 30 23 8
Then do a systemwide perf record session for a few seconds:
# perf record -a sleep 2s
Then look at:
# perf report --header-only | grep b[pt]f
# event : name = cycles:ppp, , id = { 1116204, 1116205, 1116206, 1116207, 1116208, 1116209, 1116210, 1116211 }, size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|PERIOD, read_format = ID, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, enable_on_exec = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1, ksymbol = 1, bpf_event = 1
# bpf_prog_info of id 13
# bpf_prog_info of id 14
# bpf_prog_info of id 15
# bpf_prog_info of id 16
# bpf_prog_info of id 17
# bpf_prog_info of id 18
# bpf_prog_info of id 21
# bpf_prog_info of id 22
# bpf_prog_info of id 51
# bpf_prog_info of id 52
# btf info of id 8
#
We need to show more info about these BPF and BTF entries , but that can
be done later.
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-10-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
||
|
Song Liu
|
3792cb2ff4 |
perf bpf: Save BTF in a rbtree in perf_env
BTF contains information necessary to annotate BPF programs. This patch saves BTF for BPF programs loaded in the system. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: kernel-team@fb.com Link: http://lkml.kernel.org/r/20190312053051.2690567-9-songliubraving@fb.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
|
Song Liu
|
606f972b13 |
perf bpf: Save bpf_prog_info information as headers to perf.data
This patch enables perf-record to save bpf_prog_info information as
headers to perf.data. A new header type HEADER_BPF_PROG_INFO is
introduced for this data.
Committer testing:
As root, being on the kernel sources top level directory, run:
# perf trace -e tools/perf/examples/bpf/augmented_raw_syscalls.c -e *msg
Just to compile and load a BPF program that attaches to the
raw_syscalls:sys_{enter,exit} tracepoints to trace the syscalls ending
in "msg" (recvmsg, sendmsg, recvmmsg, sendmmsg, etc).
Then do a systemwide perf record session for a few seconds:
# perf record -a sleep 2s
Then look at:
# perf report --header-only | grep -i bpf
# bpf_prog_info of id 13
# bpf_prog_info of id 14
# bpf_prog_info of id 15
# bpf_prog_info of id 16
# bpf_prog_info of id 17
# bpf_prog_info of id 18
# bpf_prog_info of id 21
# bpf_prog_info of id 22
# bpf_prog_info of id 208
# bpf_prog_info of id 209
#
We need to show more info about these programs, like bpftool does for
the ones running on the system, i.e. 'perf record/perf report' become a
way of saving the BPF state in a machine to then analyse on another,
together with all the other information that is already saved in the
perf.data header:
# perf report --header-only
# ========
# captured on : Tue Mar 12 11:42:13 2019
# header version : 1
# data offset : 296
# data size : 16294184
# feat offset : 16294480
# hostname : quaco
# os release : 5.0.0+
# perf version : 5.0.gd783c8
# arch : x86_64
# nrcpus online : 8
# nrcpus avail : 8
# cpudesc : Intel(R) Core(TM) i7-8650U CPU @ 1.90GHz
# cpuid : GenuineIntel,6,142,10
# total memory : 24555720 kB
# cmdline : /home/acme/bin/perf (deleted) record -a
# event : name = cycles:ppp, , id = { 3190123, 3190124, 3190125,
|
||
|
Song Liu
|
e4378f0cb9 |
perf bpf: Save bpf_prog_info in a rbtree in perf_env
bpf_prog_info contains information necessary to annotate bpf programs.
This patch saves bpf_prog_info for bpf programs loaded in the system.
Some big picture of the next few patches:
To fully annotate BPF programs with source code mapping, 4 different
informations are needed:
1) PERF_RECORD_KSYMBOL
2) PERF_RECORD_BPF_EVENT
3) bpf_prog_info
4) btf
Before this set, 1) and 2) in the list are already saved to perf.data
file. For BPF programs that are already loaded before perf run, 1) and 2)
are synthesized by perf_event__synthesize_bpf_events(). For short living
BPF programs, 1) and 2) are generated by kernel.
This set handles 3) and 4) from the list. Again, it is necessary to handle
existing BPF program and short living program separately.
This patch handles 3) for exising BPF programs while synthesizing 1) and
2) in perf_event__synthesize_bpf_events(). These data are stored in
perf_env. The next patch saves these data from perf_env to perf.data as
headers.
Similarly, the two patches after the next saves 4) of existing BPF
programs to perf_env and perf.data.
Another patch later will handle 3) and 4) for short living BPF programs
by monitoring 1) and 2) in a dedicate thread.
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-7-songliubraving@fb.com
[ set env->bpf_progs.infos_cnt to zero in perf_env__purge_bpf() as noted by jolsa ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
||
|
Song Liu
|
e541695045 |
perf bpf: Make synthesize_bpf_events() receive perf_session pointer instead of perf_tool
This patch changes the arguments of perf_event__synthesize_bpf_events() to include perf_session* instead of perf_tool*. perf_session will be used in the next patch. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: kernel-team@fb.com Link: http://lkml.kernel.org/r/20190312053051.2690567-6-songliubraving@fb.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
|
Song Liu
|
a742258af1 |
perf bpf: Synthesize bpf events with bpf_program__get_prog_info_linear()
With bpf_program__get_prog_info_linear, we can simplify the logic that
synthesizes bpf events.
This patch doesn't change the behavior of the code.
Commiter notes:
Needed this (for all four variables), suggested by Song, to overcome
build failure on debian experimental cross building to MIPS 32-bit:
- u8 (*prog_tags)[BPF_TAG_SIZE] = (void *)(info->prog_tags);
+ u8 (*prog_tags)[BPF_TAG_SIZE] = (void *)(uintptr_t)(info->prog_tags);
util/bpf-event.c: In function 'perf_event__synthesize_one_bpf_prog':
util/bpf-event.c:143:35: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
u8 (*prog_tags)[BPF_TAG_SIZE] = (void *)(info->prog_tags);
^
util/bpf-event.c:144:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
__u32 *prog_lens = (__u32 *)(info->jited_func_lens);
^
util/bpf-event.c:145:23: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
__u64 *prog_addrs = (__u64 *)(info->jited_ksyms);
^
util/bpf-event.c:146:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
void *func_infos = (void *)(info->func_info);
^
cc1: all warnings being treated as errors
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: kernel-team@fb.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-5-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
||
|
Song Liu
|
cae73f2339 |
bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump()
This patches uses bpf_program__get_prog_info_linear() to simplify the
logic in prog.c do_dump().
Committer testing:
Before:
# bpftool prog dump xlated id 208 > /tmp/dump.xlated.before
# bpftool prog dump jited id 208 > /tmp/dump.jited.before
# bpftool map dump id 107 > /tmp/map.dump.before
After:
# ~acme/git/perf/tools/bpf/bpftool/bpftool map dump id 107 > /tmp/map.dump.after
# ~acme/git/perf/tools/bpf/bpftool/bpftool prog dump xlated id 208 > /tmp/dump.xlated.after
# ~acme/git/perf/tools/bpf/bpftool/bpftool prog dump jited id 208 > /tmp/dump.jited.after
# diff -u /tmp/dump.xlated.before /tmp/dump.xlated.after
# diff -u /tmp/dump.jited.before /tmp/dump.jited.after
# diff -u /tmp/map.dump.before /tmp/map.dump.after
# ~acme/git/perf/tools/bpf/bpftool/bpftool prog dump xlated id 208
0: (bf) r6 = r1
1: (85) call bpf_get_current_pid_tgid#80800
2: (63) *(u32 *)(r10 -328) = r0
3: (bf) r2 = r10
4: (07) r2 += -328
5: (18) r1 = map[id:107]
7: (85) call __htab_map_lookup_elem#85680
8: (15) if r0 == 0x0 goto pc+1
9: (07) r0 += 56
10: (b7) r7 = 0
11: (55) if r0 != 0x0 goto pc+52
12: (bf) r1 = r10
13: (07) r1 += -328
14: (b7) r2 = 64
15: (bf) r3 = r6
16: (85) call bpf_probe_read#-46848
17: (bf) r2 = r10
18: (07) r2 += -320
19: (18) r1 = map[id:106]
21: (07) r1 += 208
22: (61) r0 = *(u32 *)(r2 +0)
23: (35) if r0 >= 0x200 goto pc+3
24: (67) r0 <<= 3
25: (0f) r0 += r1
26: (05) goto pc+1
27: (b7) r0 = 0
28: (15) if r0 == 0x0 goto pc+35
29: (71) r1 = *(u8 *)(r0 +0)
30: (15) if r1 == 0x0 goto pc+33
31: (b7) r5 = 64
32: (79) r1 = *(u64 *)(r10 -320)
33: (15) if r1 == 0x2 goto pc+2
34: (15) if r1 == 0x101 goto pc+3
35: (55) if r1 != 0x15 goto pc+19
36: (79) r3 = *(u64 *)(r6 +16)
37: (05) goto pc+1
38: (79) r3 = *(u64 *)(r6 +24)
39: (15) if r3 == 0x0 goto pc+15
40: (b7) r1 = 0
41: (63) *(u32 *)(r10 -260) = r1
42: (bf) r1 = r10
43: (07) r1 += -256
44: (b7) r2 = 256
45: (85) call bpf_probe_read_str#-46704
46: (b7) r5 = 328
47: (63) *(u32 *)(r10 -264) = r0
48: (bf) r1 = r0
49: (67) r1 <<= 32
50: (77) r1 >>= 32
51: (25) if r1 > 0xff goto pc+3
52: (07) r0 += 72
53: (57) r0 &= 255
54: (bf) r5 = r0
55: (bf) r4 = r10
56: (07) r4 += -328
57: (bf) r1 = r6
58: (18) r2 = map[id:105]
60: (18) r3 = 0xffffffff
62: (85) call bpf_perf_event_output_tp#-45104
63: (bf) r7 = r0
64: (bf) r0 = r7
65: (95) exit
#
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: kernel-team@fb.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-4-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
||
|
Song Liu
|
34be16466d |
tools lib bpf: Introduce bpf_program__get_prog_info_linear()
Currently, bpf_prog_info includes 9 arrays. The user has the option to fetch any combination of these arrays. However, this requires a lot of handling. This work becomes more tricky when we need to store bpf_prog_info to a file, because these arrays are allocated independently. This patch introduces 'struct bpf_prog_info_linear', which stores arrays of bpf_prog_info in continuous memory. Helper functions are introduced to unify the work to get different sets of bpf_prog_info. Specifically, bpf_program__get_prog_info_linear() allows the user to select which arrays to fetch, and handles details for the user. Please see the comments right before 'enum bpf_prog_info_array' for more details and examples. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lkml.kernel.org/r/ce92c091-e80d-a0c1-4aa0-987706c42b20@iogearbox.net Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: kernel-team@fb.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Link: http://lkml.kernel.org/r/20190312053051.2690567-3-songliubraving@fb.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
|
Song Liu
|
71184c6ab7 |
perf record: Replace option --bpf-event with --no-bpf-event
Currently, monitoring of BPF programs through bpf_event is off by default for 'perf record'. To turn it on, the user need to use option "--bpf-event". As BPF gets wider adoption in different subsystems, this option becomes inconvenient. This patch makes bpf_event on by default, and adds option "--no-bpf-event" to turn it off. Since option --bpf-event is not released yet, it is safe to remove it. Signed-off-by: Song Liu <songliubraving@fb.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: kernel-team@fb.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Fomichev <sdf@google.com> Link: http://lkml.kernel.org/r/20190312053051.2690567-2-songliubraving@fb.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> |
||
Changbin Du
|
d982b33133 |
perf tests: Fix a memory leak in test__perf_evsel__tp_sched_test()
=================================================================
==20875==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 1160 byte(s) in 1 object(s) allocated from:
#0 0x7f1b6fc84138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
#1 0x55bd50005599 in zalloc util/util.h:23
#2 0x55bd500068f5 in perf_evsel__newtp_idx util/evsel.c:327
#3 0x55bd4ff810fc in perf_evsel__newtp /home/work/linux/tools/perf/util/evsel.h:216
#4 0x55bd4ff81608 in test__perf_evsel__tp_sched_test tests/evsel-tp-sched.c:69
#5 0x55bd4ff528e6 in run_test tests/builtin-test.c:358
#6 0x55bd4ff52baf in test_and_print tests/builtin-test.c:388
#7 0x55bd4ff543fe in __cmd_test tests/builtin-test.c:583
#8 0x55bd4ff5572f in cmd_test tests/builtin-test.c:722
#9 0x55bd4ffc4087 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
#10 0x55bd4ffc45c6 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
#11 0x55bd4ffc49ca in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
#12 0x55bd4ffc5138 in main /home/changbin/work/linux/tools/perf/perf.c:520
#13 0x7f1b6e34809a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)
Indirect leak of 19 byte(s) in 1 object(s) allocated from:
#0 0x7f1b6fc83f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30)
#1 0x7f1b6e3ac30f in vasprintf (/lib/x86_64-linux-gnu/libc.so.6+0x8830f)
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes:
|
||
|
Changbin Du
|
f97a8991d3 |
perf tests: Fix memory leak by expr__find_other() in test__expr()
=================================================================
==7506==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 13 byte(s) in 3 object(s) allocated from:
#0 0x7f03339d6070 in __interceptor_strdup (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x3b070)
#1 0x5625e53aaef0 in expr__find_other util/expr.y:221
#2 0x5625e51bcd3f in test__expr tests/expr.c:52
#3 0x5625e51528e6 in run_test tests/builtin-test.c:358
#4 0x5625e5152baf in test_and_print tests/builtin-test.c:388
#5 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
#6 0x5625e515572f in cmd_test tests/builtin-test.c:722
#7 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
#8 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
#9 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
#10 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
#11 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes:
|