IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
As the devm_kcalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference.
Fixes: 349dd23931 ("ASoC: max98373: don't access volatile registers in bias level off")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20221116082508.17418-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI tx_mask and rx_mask are set by snd_soc_dai_set_tdm_slot()
and used by later code that depends on the TDM settings. So
__soc_pcm_open() should not be obliterating those mask values.
The code in __soc_pcm_hw_params() uses these masks to calculate the
active channels so that only the AIF_IN/AIF_OUT widgets for the
active TDM slots are enabled. The zeroing of the masks in
__soc_pcm_open() disables this functionality so all AIF widgets
were enabled even for channels that are not assigned to a TDM slot.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2e5894d737 ("ASoC: pcm: Add support for DAI multicodec")
Link: https://lore.kernel.org/r/20221104132213.121847-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove"),
the device power control registers are reset when the driver is
removed/shutdown.
This is an issue when the device is configured to use the PLL clock. The
device will stop responding if it is still configured to use the PLL
clock but the PLL clock is powered down.
When rebooting linux, the probe function will show:
sgtl5000 0-000a: Error reading chip id -11
Make sure that the CHIP_CLK_CTRL is reset to its default value before
powering down the device.
Fixes: bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQF_ONESHOT flag allows to ensure that the interrupt is not
unmasked after the hard interrupt context handler has been executed
and the thread has been woken. The interrupt line is unmasked after
the thread handler function has been executed.
The STM32 I2S driver does not implement a threaded IRQ handler.
So, the IRQF_ONESHOT flag is not useful in I2S driver.
Remove this flag to allow the interrupt routine to be managed
as a thread in RT mode.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20221110084406.287117-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Speaker GPIO needs to be turned on slightly behind the codec turned on.
It also need to be turned off slightly before the codec turned down.
Current code uses delay in DAPM_EVENT to do it but the mdelay delays the
DAPM itself and thus has no effect. A delayed_work is added to turn on the
speaker.
The Speaker is turned off in .trigger since trigger is called slightly
before the DAPM events.
Signed-off-by: Zhu Ning <zhuning@everest-semi.com>
------------
v1: cancel delayed work while disabling speaker.
Link: https://lore.kernel.org/r/20221028020456.90286-1-zhuning0077@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the return value check before attempting to assign the core ID to the
swidget since we are going to fail the sof_widget_ready() and free up
swidget anyways.
Fixes: 909dadf21a ("ASoC: SOF: topology: Make DAI widget parsing IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221107090433.5146-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_util_exit() is called in __init snd_soc_init() for cleanup.
Remove the __exit annotation for it to fix the build warning:
WARNING: modpost: sound/soc/snd-soc-core.o: section mismatch in reference: init_module (section: .init.text) -> snd_soc_util_exit (section: .exit.text)
Fixes: 6ec27c5388 ("ASoC: core: Fix use-after-free in snd_soc_exit()")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221031134031.256511-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with 6.0-rc1 the CPU DAI is not registered and the sound
card is unavailable. Adding legacy_dai_naming causes it to function
properly again.
Fixes: fc34ece41f ("ASoC: Refactor non_legacy_dai_naming flag")
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221103144612.4431-2-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with 6.0-rc1 these messages are logged and the sound card
is unavailable. Adding legacy_dai_naming to the rt5514-spi causes
it to function properly again.
[ 16.928454] kbl_r5514_5663_max kbl_r5514_5663_max: ASoC: CPU DAI
spi-PRP0001:00 not registered
[ 16.928561] platform kbl_r5514_5663_max: deferred probe pending
Fixes: fc34ece41f ("ASoC: Refactor non_legacy_dai_naming flag")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216641
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221103144612.4431-1-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally in commit b2ebcf42a4 ("ASoC: SOF: free widgets in
sof_tear_down_pipelines() for static pipelines"), freeing of pipeline
components at suspend was only done with recent FW as there were known
limitations in older firmware versions.
Tests show that if static pipelines are used, i.e. all pipelines are
setup whenever firmware is powered up, the reverse action of freeing all
components at power down, leads to firmware failures with also SOF2.0
and SOF2.1 based firmware.
The problems can be specific to certain topologies with e.g. components
not prepared to be freed at suspend (as this did not happen with older
SOF kernels).
To avoid hitting these problems when kernel is upgraded and used with an
older firmware, bump the firmware requirement to SOF2.2 or newer. If an
older firmware is used, and pipeline is a static one, do not free the
components at suspend. This ensures the suspend flow remains backwards
compatible with older firmware versions. This limitation does not apply
if the product configuration is updated to dynamic pipelines.
The limitation is not linked to firmware ABI, as the interface to free
pipeline components has been available already before ABI3.19. The
problem is in the implementation, so firmware version should be used to
decide whether it is safe to use the newer flow or not. This patch adds
a new SOF_FW_VER() macro to compare SOF firmware release versions.
Link: https://github.com/thesofproject/sof/issues/6475
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221101114913.1292671-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: eae9f9ce18 ("ASoC: add tas2780 driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_PM=N, pm_runtime_put_sync() returns -ENOSYS
which breaks the probe function of these drivers.
Other users of pm_runtime_put_sync() typically don't check
the return value. In order to keep the program flow as
intended, check for -ENOSYS.
This commit is similar to commit 0434d3f (omap-mailbox.c).
Fixes: cab04ab590 ("ASoC: fsl_asrc: Don't use devm_regmap_init_mmio_clk")
Fixes: 203773e393 ("ASoC: fsl_esai: Don't use devm_regmap_init_mmio_clk")
Fixes: 2277e7e36b ("ASoC: fsl_sai: Don't use devm_regmap_init_mmio_clk")
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221028141129.100702-1-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in device_del+0xb5b/0xc60
Read of size 8 at addr ffff888008655050 by task rmmod/387
CPU: 2 PID: 387 Comm: rmmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl+0x79/0x9a
print_report+0x17f/0x47b
kasan_report+0xbb/0xf0
device_del+0xb5b/0xc60
platform_device_del.part.0+0x24/0x200
platform_device_unregister+0x2e/0x40
snd_soc_exit+0xa/0x22 [snd_soc_core]
__do_sys_delete_module.constprop.0+0x34f/0x5b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
It's bacause in snd_soc_init(), snd_soc_util_init() is possble to fail,
but its ret is ignored, which makes soc_dummy_dev unregistered twice.
snd_soc_init()
snd_soc_util_init()
platform_device_register_simple(soc_dummy_dev)
platform_driver_register() # fail
platform_device_unregister(soc_dummy_dev)
platform_driver_register() # success
...
snd_soc_exit()
snd_soc_util_exit()
# soc_dummy_dev will be unregistered for second time
To fix it, handle error and stop snd_soc_init() when util_init() fail.
Also clean debugfs when util_init() or driver_register() fail.
Fixes: fb257897bf ("ASoC: Work around allmodconfig failure")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221028031603.59416-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Nanote UMPC-01 mini laptop has stereo speakers, while the default
bytcht_es8316 settings assume a mono speaker setup. Add a quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221025140942.509066-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When a component has a prefix, and uses a SND_SOC_DAPM_REGULATOR_SUPPLY,
the name of the regulator should not use the prefix, otherwise it won't
be properly matched in the DT/ACPI.
Fixes: 3caac75968 ("ASoC: soc-dapm.c: fixup snd_soc_dapm_new_control_unlocked() error handling")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221025150149.113129-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
If snd_hdac_device_register() fails, 'codec' and name allocated in
dev_set_name() called in snd_hdac_device_init() are leaked. Fix this
by calling put_device(), so they can be freed in snd_hda_codec_dev_release()
and kobject_cleanup().
Fixes: 829c673198 ("ASoC: SOF: Intel: Introduce HDA codec init and exit routines")
Fixes: dfe66a1878 ("ALSA: hdac_ext: add extended HDA bus")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20221020110157.1450191-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If snd_hdac_device_register() fails, 'codec' and name allocated in
dev_set_name() called in snd_hdac_device_init() are leaked. Fix this
by calling put_device(), so they can be freed in snd_hda_codec_dev_release()
and kobject_cleanup().
Fixes: e4746d94d0 ("ASoC: Intel: Skylake: Introduce HDA codec init and exit routines")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221020105937.1448951-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ADL-N uses a different signing key, which means we can't reuse the
regular ADL descriptor used for ADL-P/M/S.
Fixes: cd57eb3c40 ("ASoC: SOF: Intel: pci-tgl: add ADL-N support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221019154926.163539-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Update LPASS_HDMI_TX_PARITY_ADDR register as volatile, to fix
dp audio failures observed with some of external monitors.
Fixes: 7cb37b7bd0 ("ASoC: qcom: Add support for lpass hdmi driver")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1665825530-7593-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Siarhei Volkau <lis8215@gmail.com>:
The patchset fixes:
- Line In path stays powered off during capturing or
bypass to mixer.
- incorrectly represented dB values in alsamixer, et al.
- incorrect represented Capture input selector in alsamixer
in Playback tab.
- wrong control selected as Capture Master
There are two spelling mistakes in codec routing description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221019071639.1003730-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "convert-xxx" properties only have an effect for DPCM DAI links.
A DAI link is only created as DPCM if the device tree requires it;
part of this involves checking for the use of "convert-xxx" properties.
When the convert-sample-format property was added, the checks got out
of sync. A DAI link that specified only convert-sample-format but did
not pass any of the other DPCM checks would not go into DPCM mode and
the convert-sample-format property would be silently ignored.
Fix this by adding a function to do the "convert-xxx" property checks,
instead of open-coding it in simple-card and audio-graph-card. And add
"convert-sample-format" to the check function so that DAI links using
it will be initialized correctly.
Fixes: 047a05366f ("ASoC: simple-card-utils: Fixup DAI sample format")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20221019012302.633830-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the pad control and checks the
hardware version to set the different preset settings.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221019095731.31101-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add protection against multiple open of the mtrace/coreN debugfs
nodes. This is not supported in the implementation, and this will
show up as unexpected behaviour of the interface, and potential
use of already freed memory.
Fixes: f4ea22f7aa ("ASoC: SOF: ipc4: Add support for mtrace log extraction")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221018121332.20802-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial IPC4 tests used the same conventions as previous reference
closed-source firmware, but for MeteorLake the convention is the same
as previous SOF releases (sof-<platform>.ri). Only the prefix changes
to avoid confusions between IPC types.
This change has no impact on users since the firmware has not yet been
released.
Fixes: 064520e8ae ("ASoC: SOF: Intel: Add support for MeteorLake (MTL)")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221017204004.207446-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If SOUNDWIRE is enabled, then SND_SOC_SC7180 should depend on
SOUNDWIRE to prevent SOUNDWIRE=m and SND_SOC_SC7180=y, which causes
build errors:
s390-linux-ld: sound/soc/qcom/common.o: in function `qcom_snd_sdw_prepare':
common.c:(.text+0x140): undefined reference to `sdw_disable_stream'
s390-linux-ld: common.c:(.text+0x14a): undefined reference to `sdw_deprepare_stream'
s390-linux-ld: common.c:(.text+0x158): undefined reference to `sdw_prepare_stream'
s390-linux-ld: common.c:(.text+0x16a): undefined reference to `sdw_enable_stream'
s390-linux-ld: common.c:(.text+0x17c): undefined reference to `sdw_deprepare_stream'
s390-linux-ld: sound/soc/qcom/common.o: in function `qcom_snd_sdw_hw_free':
common.c:(.text+0x344): undefined reference to `sdw_disable_stream'
s390-linux-ld: common.c:(.text+0x34e): undefined reference to `sdw_deprepare_stream'
Fixes: 3bd975f3ae ("ASoC: qcom: sm8250: move some code to common")
Fixes: 9e3ecb5b16 ("ASoC: qcom: sc7180: Add machine driver for sound card registration")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Banajit Goswami <bgoswami@quicinc.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Ajit Pandey <ajitp@codeaurora.org>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: stable@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Link: https://lore.kernel.org/r/20221015001228.18990-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_SND_SOC_TLV320ADC3XXX=y:
`.exit.text' referenced in section `.data' of sound/soc/codecs/tlv320adc3xxx.o: defined in discarded section `.exit.text' of sound/soc/codecs/tlv320adc3xxx.o
Fix this by wrapping the adc3xxx_i2c_remove() pointer in __exit_p().
Fixes: e9a3b57efd ("ASoC: codec: tlv320adc3xxx: New codec driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/3225ba4cfe558d9380155e75385954dd21d4e7eb.1665909132.git.geert@linux-m68k.org
Signed-off-by: Mark Brown <broonie@kernel.org>
At the moment Capture source selector appears on Playback
tab in the alsamixer and has a senseless name.
Let's fix that.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-5-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-4-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-3-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Update HDMI volatile registers list as DMA, Channel Selection registers,
vbit control registers are being reflected by hardware DP port
disconnection.
This update is required to fix no display and no sound issue observed
after reconnecting TAMA/SANWA DP cables.
Once DP cable is unplugged, DMA control registers are being reset by
hardware, however at second plugin, new dma control values does not
updated to the dma hardware registers since new register value and
cached values at the time of first plugin are same.
Fixes: 7cb37b7bd0 ("ASoC: qcom: Add support for lpass hdmi driver")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reported-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Link: https://lore.kernel.org/r/1665637711-13300-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Tested-by: Adam Ford <aford173@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
