IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
GISB bus error kernel panics have been observed during S2 transition
tests on the 7271t platform. The errors are a result of the BDC
interrupt handler trying to access BDC register space after the
system's suspend callbacks have completed.
Adding a suspend hook to the BDC driver that halts the controller before
S2 entry thus preventing unwanted access to the BDC register space during
this transition.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Version v1.0.40 of the Android host ADB software increased maximum
transfer sizes from 256K to 1M. Since the STB ADB gadget driver
requests only 16K at a time, the BDC driver ran out of buffer
descriptors (BDs) if the queuing happens faster than the incoming
16K transfers. This issue is fixed by doubling the number of BDs
that can be queued so that the entire 1M request can be queued
without running out of buffers.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On Android systems, After temporarily putting device to S2 by
short pressing the power button on the remote, the display turns
off. Then press the power button to turn the display back up. Adb
devices would show the devices is offline. It needs a physical
disconnect of the usb cable or power cycle to bring the device
back online. The device is operational otherwise.
The problem is that during S2 resume, the ADB gadget driver could
not link back with the BDC driver because the endpoint flags were
cleared. The fix is to clear the endpoint flags for the disconnect
case only and not for S2 exit.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Multiple connects/disconnects can cause a crash on the second
disconnect. The driver had a problem where it would try to send
endpoint commands after it was disconnected which is not allowed
by the hardware. The fix is to only allow the endpoint commands
when the endpoint is connected. This will also fix issues that
showed up when using configfs to create gadgets.
Signed-off-by: Sasi Kumar <sasi.kumar@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add compatible string for some newer boards that only have this
as their match sting. Remove unused compatible string "brcm,bdc-v0.16".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Reformat the code (add one level of indentation before the values),
to align the code in the macro definition section.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>
Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add support for probing the phy-jz4770 driver on the JZ4780 SoC,
the X1000 SoC and the X1830 SoC from Ingenic.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>
Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
1.Modify the macro definition to unify "#define USBPCR_XXXX n"
into the "#define USBPCR_XXXX (n << USBPCR_XXXX_LSB)" style,
so as to unify the code style in the "jz4770_phy_init()" and
simplify the code.
2.Remove unused macro definitions to simplify the code.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Driver does not release memory for device on error handling paths in
net2280_probe() when gadget_release() is not registered yet.
The patch fixes the bug like in other similar drivers.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch split function cdns3_drd_switch_gadget and
cdns3_drd_switch_host into:
- cdns3_drd_host_on
- cdns3_drd_host_off
- cdns3_drd_gadget_on
- cdns3_drd_gadgett_off
These functions don't have any shared code so it's better to
have smaller, faster and easier functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some error code can be preserved, so we can remove overwriting
error code returned by some functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch adds 2 definitions that make it easier to understand the code.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch changes return type from int to bool for
cdns3_is_host and cdns3_is_device functions.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
IRQ_NONE can be returned indirect.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch remove some variables initialization from core.c and drd.c
file.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Function is not used in driver so it can be removed.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It doesn't need to enable/disable L1 on the fly for EP0 transfer,
we only need to enable L1 after SET_CONFIGURATION.
This code may be introduced by careless.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
net2272_rdk1_probe() skips "i == 1" (BAR1) during allocation of
resources. The patch does this on error hanling paths as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When gadget registration fails, one should not call usb_del_gadget_udc().
Ensure this by setting gadget->udc to NULL. Also in case of a failure
there is no need to disable low-level hardware, so return immiedetly
instead of jumping to error_init label.
This fixes the following kernel NULL ptr dereference on gadget failure
(can be easily triggered with g_mass_storage without any module
parameters):
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.8.0-rc5 #3133
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at usb_del_gadget_udc+0x38/0xc4
LR is at __mutex_lock+0x31c/0xb18
...
Process kworker/0:1 (pid: 12, stack limit = 0x(ptrval))
Stack: (0xef121db0 to 0xef122000)
...
[<c076bf3c>] (usb_del_gadget_udc) from [<c0726bec>] (dwc2_hsotg_remove+0x10/0x20)
[<c0726bec>] (dwc2_hsotg_remove) from [<c0711208>] (dwc2_driver_probe+0x57c/0x69c)
[<c0711208>] (dwc2_driver_probe) from [<c06247c0>] (platform_drv_probe+0x6c/0xa4)
[<c06247c0>] (platform_drv_probe) from [<c0621df4>] (really_probe+0x200/0x48c)
[<c0621df4>] (really_probe) from [<c06221e8>] (driver_probe_device+0x78/0x1fc)
[<c06221e8>] (driver_probe_device) from [<c061fcd4>] (bus_for_each_drv+0x74/0xb8)
[<c061fcd4>] (bus_for_each_drv) from [<c0621b54>] (__device_attach+0xd4/0x16c)
[<c0621b54>] (__device_attach) from [<c0620c98>] (bus_probe_device+0x88/0x90)
[<c0620c98>] (bus_probe_device) from [<c06211b0>] (deferred_probe_work_func+0x3c/0xd0)
[<c06211b0>] (deferred_probe_work_func) from [<c0149280>] (process_one_work+0x234/0x7dc)
[<c0149280>] (process_one_work) from [<c014986c>] (worker_thread+0x44/0x51c)
[<c014986c>] (worker_thread) from [<c0150b1c>] (kthread+0x158/0x1a0)
[<c0150b1c>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xef121fb0 to 0xef121ff8)
...
---[ end trace 9724c2fc7cc9c982 ]---
While fixing this also fix the double call to dwc2_lowlevel_hw_disable()
if dr_mode is set to USB_DR_MODE_PERIPHERAL. In such case low-level
hardware is already disabled before calling usb_add_gadget_udc(). That
function correctly preserves low-level hardware state, there is no need
for the second unconditional dwc2_lowlevel_hw_disable() call.
Fixes: 207324a321a8 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Implement udc->pullup callback, so that udc_connect/disconnect work.
This is needed for composite gadget, as it assumes udc_disconnect()
actually works and calls its ->disconnect callback.
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When binding an UDC driver to the pending gadget fails in
check_pending_gadget_drivers(), the usb_add_gadget_udc_release() function
ends without waiting for the usb_gadget_state_work to finish, what in
turn might cause the whole struct usb_gadget being freed by the caller
before the usb_gadget_state_work being executed.
This can be observed on some boards with USB Mass Storage gadget
compiled-in and kernel booted without the needed module parameters:
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
dwc2: probe of 12480000.hsotg failed with error -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = (ptrval)
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 88 Comm: kworker/1:2 Not tainted 5.8.0-rc5-next-20200715-00062-gc5bb489ae825-dirty #8792
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: 0x0 (rcu_gp)
PC is at process_one_work+0x44/0x7dc
...
Process kworker/1:2 (pid: 88, stack limit = 0x(ptrval))
Stack: (0xed9f1f00 to 0xed9f2000)
...
[<c0148590>] (process_one_work) from [<c0148d6c>] (worker_thread+0x44/0x51c)
[<c0148d6c>] (worker_thread) from [<c01500c0>] (kthread+0x158/0x1a0)
[<c01500c0>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xed9f1fb0 to 0xed9f1ff8)
...
---[ end trace 5033c1326a62e5f3 ]---
note: kworker/1:2[88] exited with preempt_count 1
Fix this by flushing pending work in error path.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Delete the duplicated EP_CMD_ERDY and EP_CMD_REQ_CMPL setting
- Prepare the next setup before setting EP_CMD_ERDY and EP_CMD_REQ_CMPL,
it could avoid a bug that DMA hang at EP0 OUT for DEV_VER_NXP_V1
- Delete the duplicated cdns3_set_hw_configuration calling at
cdns3_req_ep0_set_configuration, the composite.c will handle
this request, and call .ep0_queue back, and at .ep_queue it will
call cdns3_set_hw_configuration.
- Move cdns3_allow_enable_l1 into cdns3_set_hw_configuration since
it is part of this function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The reset is a shared reset line, but reset_control_reset is still used
and reset_control_deassert is not guaranteed to have been called before
the first reset_control_assert call. When suspending the following
warning may be seen:
WARNING: CPU: 1 PID: 5530 at drivers/reset/core.c:355 reset_control_assert+0x184/0x19c
Hardware name: Hardkernel ODROID-N2 (DT)
[..]
pc : reset_control_assert+0x184/0x19c
lr : dwc3_meson_g12a_suspend+0x68/0x7c
[..]
Call trace:
reset_control_assert+0x184/0x19c
dwc3_meson_g12a_suspend+0x68/0x7c
platform_pm_suspend+0x28/0x54
__device_suspend+0x590/0xabc
dpm_suspend+0x104/0x404
dpm_suspend_start+0x84/0x1bc
suspend_devices_and_enter+0xc4/0x4fc
pm_suspend+0x198/0x2d4
Fixes: 6d9fa35a347a87 ("usb: dwc3: meson-g12a: get the reset as shared")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
dbc should not be aware of, or use any dbctty specific variables.
currenly dbc driver reads the port->registered flag to see if the
callbacks should be called.
Only makes these decisions based on dbc internal state instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't call dbctty driver functions directly from dbc core code.
Introduce a new dbc_driver structure that contains function pointers
for disconnect and configure operations.
The driver (ttydbc) must provide these opeations when creating a dbc.
Name the structure dbc_driver instead of dbc_ops as we plan to
add more driver configureable values here, such as vid and pid.
Decouples dbc and dbctty.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the dbc tty driver registrations function into separate
init and probe parts.
The init part will register the tty driver, and should in the future be
called from module_init().
The probe part will become the normal probe function, but for now it is
called from the init part.
The unregister function is s likewise split into remove and exit parts.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't pass endpoint pointer, dbctty should not be aware of
struct dbc_ep, knowing the direction is enough.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-23-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_dbc_start() and xhci_dbc_stop() functions only used xhci_hcd pointer
to get the dbc pointer.
Pass the dbc pointer instead of the xhci_hcd pointer as a parameter
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dbc mem_init and mem_cleanup functions used xhci_hcd to get to the device
pointer. The device pointer can be accessed directly from dbc structure,
so pass a pointer to dbc as a parameter instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic xhci ring allocations code needs struct xhci_hcd pointer, and
it allocates memory for the rings from dma pools created for the xhci
device.
In order to decouple xhci and DbC we have to create our own ring allocation
and free routines for DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DbC context is different from the xhci device context.
It's a lot smaller as it only contains three 64 bytes sub-contexts;
the info, endpoint-out, and endpoint-in contexts. In total 192 bytes.
The context size (CSZ) field in HCCPARAMS1 xhci register does not alter
DbC context size like it does for xhci device contexts.
So don't use the geneic xhci context memory allocation, or the
dma pool that is intended for xhci device contexts.
In addition to saving memory this also helps decoupleing xhci and dbc code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dbc request completion callback doesn't need a xhci_hcd pointer.
The only user of the xhci_hcd pointer in dbgtty request callback was
the xhci_warn() function. Change it to dev_warn() instead.
While changing the callback function parameter to dbc in struct
xhci_requeset, move the struct xhci_request declaraion down a bit in the
header file to avoid compiler warinings
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass dbc pointer instead of struct xhci_hcd pointer to the get_in_ep() and
get_out_ep() helper functions.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass dbc pointer to the xhci_dbc_tty_register_device() and
xhci_dbc_tty_unregister_device() functions instead of xhci_hcd pointer
These functions don't need a xhci_hcd pointer anymore, only use case was
the xhci_err() function, which is now changed to a dev_err() instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event handling function only used xhci pointer to get the dbc pointer.
Pass the dbc pointer instead as a parameter
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass the dbc pointer instead of xhci_hcd pointer in order to
decouple xhci and dbc.
xhci_do_dbc_stop() only used xhci to get the dbc pointer.
Pass the dbc pointer instead as a parameter
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct xhci_hcd pointer is not needed for dbc endpoint init and exit,
it was only used to get to the dbc structure.
Pass the dbc pointer as a parameter to these functions instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbc_ep_do_queue() can now get the device pointer directly from dbc
structure instead of going through the xhci_hcd structure.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_write_64() is essentially a wrapper for lo_hi_writeq(), but it
requires struct xhci_hcd * as a parameter.
Use lo_hi_writeq() directly instead
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make this change possible we also need to change
dbc_handle_port_status() to take dbc pointer as parameter instead of
xhci_hcd pointer.
Note that xhci_info() used xhci_to_hcd(xhci)->self.controller as the
device while for dev_info we use xhci_to_hcd(xhci)->self.sysdev.
In many cases those are the same, but not for some device where
a dwc3 controller creates a xhci platform device. In th this case
self.controller may be the platform device while self.sysdev is
the actual device known to firmware (dwc3).
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the dbc structure contains a pointer to struct xhci_hcd,
and dbc functions use that to dig up the underlying device pointer.
We are trying to decouple xhci and dbc code, and prepare for
code that use dbc such as dbctty into into real device drivers.
This is one step along the way.
Keep functionality the same and keep the xhci pointer, and
let the new device pointer point to the xhci device for now.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbc_dma_free_coherent() takes struct xhci_hcd pointer as a parameter, but
does nothing more than calls dma_free_coherent().
Remove it and call dma_free_coherent() directly instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbc_dma_alloc_coherent() takes struct xhci_hcd pointer as an parameter, but
does nothing more than calls dma_alloc_coherent().
Remove it and call dma_alloc_coherent() directly instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
