IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
By printing information, we can friendly prompt the status change
information of kfence by dmesg and record by syslog.
Also, set kfence_enabled to false only when needed.
Link: https://lkml.kernel.org/r/20220518073105.3160335-1-liu.yun@linux.dev
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Co-developed-by: Marco Elver <elver@google.com>
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In isolate_single_pageblock() called by start_isolate_page_range(), there
are some pageblock isolation issues causing a potential infinite loop when
isolating a page range. This is reported by Qian Cai.
1. the pageblock was isolated by just changing pageblock migratetype
without checking unmovable pages. Calling set_migratetype_isolate() to
isolate pageblock properly.
2. an off-by-one error caused migrating pages unnecessarily, since the page
is not crossing pageblock boundary.
3. migrating a compound page across pageblock boundary then splitting the
free page later has a small race window that the free page might be
allocated again, so that the code will try again, causing an potential
infinite loop. Temporarily set the to-be-migrated page's pageblock to
MIGRATE_ISOLATE to prevent that and bail out early if no free page is
found after page migration.
An additional fix to split_free_page() aims to avoid crashing in
__free_one_page(). When the free page is split at the specified
split_pfn_offset, free_page_order should check both the first bit of
free_page_pfn and the last bit of split_pfn_offset and use the smaller
one. For example, if free_page_pfn=0x10000, split_pfn_offset=0xc000,
free_page_order should first be 0x8000 then 0x4000, instead of 0x4000 then
0x8000, which the original algorithm did.
[akpm@linux-foundation.org: suppress min() warning]
Link: https://lkml.kernel.org/r/20220524194756.1698351-1-zi.yan@sent.com
Fixes: b2c9e2fbba ("mm: make alloc_contig_range work at pageblock granularity")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David Hildenbrand <david@redhat.com>
Cc: Eric Ren <renzhengeek@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Shmem swapoff makes no progress: the index to indices is not incremented.
But "ret" is no longer a return value, so use folio_batch_count() instead.
Link: https://lkml.kernel.org/r/c32bee8a-f0aa-245-f94e-24dd271924fa@google.com
Fixes: da08e9b793 ("mm/shmem: convert shmem_swapin_page() to shmem_swapin_folio()")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We expect no warnings to be issued when we specify __GFP_NOWARN, but
currently in paths like alloc_pages() and kmalloc(), there are still some
warnings printed, fix it.
But for some warnings that report usage problems, we don't deal with them.
If such warnings are printed, then we should fix the usage problems.
Such as the following case:
WARN_ON_ONCE((gfp_flags & __GFP_NOFAIL) && (order > 1));
[zhengqi.arch@bytedance.com: v2]
Link: https://lkml.kernel.org/r/20220511061951.1114-1-zhengqi.arch@bytedance.com
Link: https://lkml.kernel.org/r/20220510113809.80626-1-zhengqi.arch@bytedance.com
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently, trace point mm_page_alloc_zone_locked() doesn't show correct
information.
First, when alloc_flag has ALLOC_HARDER/ALLOC_CMA, page can be allocated
from MIGRATE_HIGHATOMIC/MIGRATE_CMA. Nevertheless, tracepoint use
requested migration type not MIGRATE_HIGHATOMIC and MIGRATE_CMA.
Second, after commit 44042b4498 ("mm/page_alloc: allow high-order pages
to be stored on the per-cpu lists") percpu-list can store high order
pages. But trace point determine whether it is a refiil of percpu-list by
comparing requested order and 0.
To handle these problems, make mm_page_alloc_zone_locked() only be called
by __rmqueue_smallest with correct migration type. With a new argument
called percpu_refill, it can show roughly whether it is a refill of
percpu-list.
Link: https://lkml.kernel.org/r/20220512025307.57924-1-vvghjk1234@gmail.com
Signed-off-by: Wonhyuk Yang <vvghjk1234@gmail.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Baik Song An <bsahn@etri.re.kr>
Cc: Hong Yeon Kim <kimhy@etri.re.kr>
Cc: Taeung Song <taeung@reallinux.co.kr>
Cc: <linuxgeek@linuxgeek.io>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch fixes two issues:
1. Add __initdata attribute according to include/linux/init.h:
For initialized data:
You should insert __initdata between the variable name and equal
sign followed by value
2. Fix below error reported by checkpatch.pl:
ERROR: do not initialise statics to false
Special thanks to Muchun Song :)
Link: https://lkml.kernel.org/r/20220516030039.1487005-1-bh1scw@gmail.com
Signed-off-by: Fanjun Kong <bh1scw@gmail.com>
Suggested-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The rmap locks(i_mmap_rwsem and anon_vma->root->rwsem) could be contended
under memory pressure if processes keep working on their vmas(e.g., fork,
mmap, munmap). It makes reclaim path stuck. In our real workload traces,
we see kswapd is waiting the lock for 300ms+(worst case, a sec) and it
makes other processes entering direct reclaim, which were also stuck on
the lock.
This patch makes lru aging path try_lock mode like shink_page_list so the
reclaim context will keep working with next lru pages without being stuck.
if it found the rmap lock contended, it rotates the page back to head of
lru in both active/inactive lrus to make them consistent behavior, which
is basic starting point rather than adding more heristic.
Since this patch introduces a new "contended" field as out-param along
with try_lock in-param in rmap_walk_control, it's not immutable any longer
if the try_lock is set so remove const keywords on rmap related functions.
Since rmap walking is already expensive operation, I doubt the const
would help sizable benefit( And we didn't have it until 5.17).
In a heavy app workload in Android, trace shows following statistics. It
almost removes rmap lock contention from reclaim path.
Martin Liu reported:
Before:
max_dur(ms) min_dur(ms) max-min(dur)ms avg_dur(ms) sum_dur(ms) count blocked_function
1632 0 1631 151.542173 31672 209 page_lock_anon_vma_read
601 0 601 145.544681 28817 198 rmap_walk_file
After:
max_dur(ms) min_dur(ms) max-min(dur)ms avg_dur(ms) sum_dur(ms) count blocked_function
NaN NaN NaN NaN NaN 0.0 NaN
0 0 0 0.127645 1 12 rmap_walk_file
[minchan@kernel.org: add comment, per Matthew]
Link: https://lkml.kernel.org/r/YnNqeB5tUf6LZ57b@google.com
Link: https://lkml.kernel.org/r/20220510215423.164547-1-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: John Dias <joaodias@google.com>
Cc: Tim Murray <timmurray@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Martin Liu <liumartin@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Applications can currently escape their cgroup memory containment when
zswap is enabled. This patch adds per-cgroup tracking and limiting of
zswap backend memory to rectify this.
The existing cgroup2 memory.stat file is extended to show zswap statistics
analogous to what's in meminfo and vmstat. Furthermore, two new control
files, memory.zswap.current and memory.zswap.max, are added to allow
tuning zswap usage on a per-workload basis. This is important since not
all workloads benefit from zswap equally; some even suffer compared to
disk swap when memory contents don't compress well. The optimal size of
the zswap pool, and the threshold for writeback, also depends on the size
of the workload's warm set.
The implementation doesn't use a traditional page_counter transaction.
zswap is unconventional as a memory consumer in that we only know the
amount of memory to charge once expensive compression has occurred. If
zwap is disabled or the limit is already exceeded we obviously don't want
to compress page upon page only to reject them all. Instead, the limit is
checked against current usage, then we compress and charge. This allows
some limit overrun, but not enough to matter in practice.
[hannes@cmpxchg.org: fix for CONFIG_SLOB builds]
Link: https://lkml.kernel.org/r/YnwD14zxYjUJPc2w@cmpxchg.org
[hannes@cmpxchg.org: opt out of cgroups v1]
Link: https://lkml.kernel.org/r/Yn6it9mBYFA+/lTb@cmpxchg.org
Link: https://lkml.kernel.org/r/20220510152847.230957-7-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently it requires poking at debugfs to figure out the size and
population of the zswap cache on a host. There are no counters for reads
and writes against the cache. As a result, it's difficult to understand
zswap behavior on production systems.
Print zswap memory consumption and how many pages are zswapped out in
/proc/meminfo. Count zswapouts and zswapins in /proc/vmstat.
Link: https://lkml.kernel.org/r/20220510152847.230957-6-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
- CONFIG_ZRAM: Zram is a user-facing feature, whereas zsmalloc is
not. Don't make the user chase down a technical dependency like
that, just select it in automatically when zram is requested. The
CONFIG_CRYPTO dependency is redundant due to more specific deps.
- CONFIG_ZPOOL: This is not a user-facing feature. Hide the symbol and
have it selected in as needed.
- CONFIG_ZSWAP: Select CRYPTO instead of depend. Common pattern.
- Make the ZSWAP suboptions and their descriptions (compression,
allocation backend) a bit more straight-forward for the user.
Link: https://lkml.kernel.org/r/20220510152847.230957-5-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There are several clusters of related config options spread throughout the
mostly flat MM submenu. Group them together and put specialization
options into further subdirectories to make the MM submenu a bit more
organized and easier to navigate.
[hannes@cmpxchg.org: fix kbuild warnings]
Link: https://lkml.kernel.org/r/YnvkSVivfnT57Vwh@cmpxchg.org
[hannes@cmpxchg.org: fix more kbuild warnings]
Link: https://lkml.kernel.org/r/Ynz8NusTdEGcCnJN@cmpxchg.org
Link: https://lkml.kernel.org/r/20220510152847.230957-4-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
These are currently under General Setup. MM seems like a better fit.
Link: https://lkml.kernel.org/r/20220510152847.230957-3-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since commit 4efaceb1c5 ("mm, swap: use rbtree for swap_extent"), rbtree
is used for swap extent. Also curr_swap_extent is removed at that time.
Update the corresponding comment.
Link: https://lkml.kernel.org/r/20220509131416.17553-16-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If no pages were pinned, 0 is returned in fact. Fix the corresponding
comment.
[akpm@linux-foundation.org: s/nr_pages/nr_segs/ also, per David, reflow comment]
Link: https://lkml.kernel.org/r/20220509131416.17553-15-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use flags of si directly to check SWP_STABLE_WRITES to avoid possible
READ_ONCE and thus save some cpu cycles.
[akpm@linux-foundation.org: use data_race() on si->flags, per Neil]
Link: https://lkml.kernel.org/r/20220509131416.17553-10-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make page_swapcount and __lru_add_drain_all static. They are only used
within the file now.
Link: https://lkml.kernel.org/r/20220509131416.17553-9-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If p is NULL, __swap_duplicate will already return -EINVAL. So if we
reach here, p must be non-NULL.
Link: https://lkml.kernel.org/r/20220509131416.17553-8-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
refill_swap_slots_cache is always called when cache->nr is 0. So remove
such buggy and confusing check.
Link: https://lkml.kernel.org/r/20220509131416.17553-7-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If offset exceeds the si->max, print bad swap offset entry to help debug
the unexpected case.
Link: https://lkml.kernel.org/r/20220509131416.17553-6-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The return value of free_swap_slot is always 0 and also ignored now.
Remove it to clean up the code.
Link: https://lkml.kernel.org/r/20220509131416.17553-5-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fold __swap_info_get() into its sole caller to make code more clear.
Minor readability improvement.
Link: https://lkml.kernel.org/r/20220509131416.17553-4-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use helper macro __ATTR_RW to define vma_ra_enabled_attr to make code more
clear. Minor readability improvement.
Link: https://lkml.kernel.org/r/20220509131416.17553-3-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "A few cleanup patches for swap".
This series contains a few patches to fix the comment, remove unneeded
return value, use some helpers and so on. More details can be found in
the respective changelogs.
This patch (of 14):
Use helper is_swap_pte() to check whether pte is swap entry to make code
more clear. Minor readability improvement.
Link: https://lkml.kernel.org/r/20220509131416.17553-1-linmiaohe@huawei.com
Link: https://lkml.kernel.org/r/20220509131416.17553-2-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Howells <dhowells@redhat.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The readonly FS THP relies on khugepaged to collapse THP for suitable
vmas. But the behavior is inconsistent for "always" mode
(https://lore.kernel.org/linux-mm/00f195d4-d039-3cf2-d3a1-a2c88de397a0@suse.cz/).
The "always" mode means THP allocation should be tried all the time and
khugepaged should try to collapse THP all the time. Of course the
allocation and collapse may fail due to other factors and conditions.
Currently file THP may not be collapsed by khugepaged even though all the
conditions are met. That does break the semantics of "always" mode.
So make sure readonly FS vmas are registered to khugepaged to fix the
break.
Register suitable vmas in common mmap path, that could cover both readonly
FS vmas and shmem vmas, so remove the khugepaged calls in shmem.c.
Still need to keep the khugepaged call in vma_merge() since vma_merge() is
called in a lot of places, for example, madvise, mprotect, etc.
Link: https://lkml.kernel.org/r/20220510203222.24246-9-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Vlastmil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Song Liu <song@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The khugepaged_enter_vma_merge() actually does as the same thing as the
khugepaged_enter() section called by shmem_mmap(), so consolidate them
into one helper and rename it to khugepaged_enter_vma().
Link: https://lkml.kernel.org/r/20220510203222.24246-8-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Acked-by: Vlastmil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Song Liu <song@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The hugepage_vma_check() could be reused by khugepaged_enter() and
khugepaged_enter_vma_merge(), but it is static in khugepaged.c. Make it
non-static and declare it in khugepaged.h.
Link: https://lkml.kernel.org/r/20220510203222.24246-7-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Song Liu <song@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The most callers of khugepaged_enter() don't care about the return value.
Only dup_mmap(), anonymous THP page fault and MADV_HUGEPAGE handle the
error by returning -ENOMEM. Actually it is not harmful for them to ignore
the error case either. It also sounds overkilling to fail fork() and page
fault early due to khugepaged_enter() error, and MADV_HUGEPAGE does set
VM_HUGEPAGE flag regardless of the error.
Link: https://lkml.kernel.org/r/20220510203222.24246-6-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Vlastmil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since commit a4aeaa06d4 ("mm: khugepaged: skip huge page collapse for
special files"), khugepaged just collapses THP for regular file which is
the intended usecase for readonly fs THP. Only show regular file as THP
eligible accordingly.
And make file_thp_enabled() available for khugepaged too in order to
remove duplicate code.
Link: https://lkml.kernel.org/r/20220510203222.24246-5-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Vlastmil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The DAX vma may be seen by khugepaged when the mm has other khugepaged
suitable vmas. So khugepaged may try to collapse THP for DAX vma, but it
will fail due to page sanity check, for example, page is not on LRU.
So it is not harmful, but it is definitely pointless to run khugepaged
against DAX vma, so skip it in early check.
Link: https://lkml.kernel.org/r/20220510203222.24246-4-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Vlastmil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The hugepage_vma_check() called by khugepaged_enter_vma_merge() does check
VM_NO_KHUGEPAGED. Remove the check from caller and move the check in
hugepage_vma_check() up.
More checks may be run for VM_NO_KHUGEPAGED vmas, but MADV_HUGEPAGE is
definitely not a hot path, so cleaner code does outweigh.
Link: https://lkml.kernel.org/r/20220510203222.24246-3-shy828301@gmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Vlastmil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
At present, pages not in the target zone are added to cc->migratepages
list in isolate_migratepages_block(). As a result, pages may migrate
between nodes unintentionally.
This would be a serious problem for older kernels without commit
a984226f45 ("mm: memcontrol: remove the pgdata parameter of
mem_cgroup_page_lruvec"), because it can corrupt the lru list by
handling pages in list without holding proper lru_lock.
Avoid returning a pfn outside the target zone in the case that it is
not aligned with a pageblock boundary. Otherwise
isolate_migratepages_block() will handle pages not in the target zone.
Link: https://lkml.kernel.org/r/20220511044300.4069-1-yamamoto.rei@jp.fujitsu.com
Fixes: 70b44595ea ("mm, compaction: use free lists to quickly locate a migration source")
Signed-off-by: Rei Yamamoto <yamamoto.rei@jp.fujitsu.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Wonhyuk Yang <vvghjk1234@gmail.com>
Cc: Rei Yamamoto <yamamoto.rei@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We run a lot of automated tests when building our software and run into
OOM scenarios when the tests run unbounded. v1 memcg exports
memcg->watermark as "memory.max_usage_in_bytes" in sysfs. We use this
metric to heuristically limit the number of tests that can run in parallel
based on per test historical data.
This metric is currently not exported for v2 memcg and there is no other
easy way of getting this information. getrusage() syscall returns
"ru_maxrss" which can be used as an approximation but that's the max RSS
of a single child process across all children instead of the aggregated
max for all child processes. The only work around is to periodically poll
"memory.current" but that's not practical for short-lived one-off cgroups.
Hence, expose memcg->watermark as "memory.peak" for v2 memcg.
Link: https://lkml.kernel.org/r/20220507050916.GA13577@us192.sjc.aristanetworks.com
Signed-off-by: Ganesan Rajagopal <rganesan@arista.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We must add hugetlb_free_vmemmap=on (or "off") to the boot cmdline and
reboot the server to enable or disable the feature of optimizing vmemmap
pages associated with HugeTLB pages. However, rebooting usually takes a
long time. So add a sysctl to enable or disable the feature at runtime
without rebooting. Why we need this? There are 3 use cases.
1) The feature of minimizing overhead of struct page associated with
each HugeTLB is disabled by default without passing
"hugetlb_free_vmemmap=on" to the boot cmdline. When we (ByteDance)
deliver the servers to the users who want to enable this feature, they
have to configure the grub (change boot cmdline) and reboot the
servers, whereas rebooting usually takes a long time (we have thousands
of servers). It's a very bad experience for the users. So we need a
approach to enable this feature after rebooting. This is a use case in
our practical environment.
2) Some use cases are that HugeTLB pages are allocated 'on the fly'
instead of being pulled from the HugeTLB pool, those workloads would be
affected with this feature enabled. Those workloads could be
identified by the characteristics of they never explicitly allocating
huge pages with 'nr_hugepages' but only set 'nr_overcommit_hugepages'
and then let the pages be allocated from the buddy allocator at fault
time. We can confirm it is a real use case from the commit
099730d674. For those workloads, the page fault time could be ~2x
slower than before. We suspect those users want to disable this
feature if the system has enabled this before and they don't think the
memory savings benefit is enough to make up for the performance drop.
3) If the workload which wants vmemmap pages to be optimized and the
workload which wants to set 'nr_overcommit_hugepages' and does not want
the extera overhead at fault time when the overcommitted pages be
allocated from the buddy allocator are deployed in the same server.
The user could enable this feature and set 'nr_hugepages' and
'nr_overcommit_hugepages', then disable the feature. In this case, the
overcommited HugeTLB pages will not encounter the extra overhead at
fault time.
Link: https://lkml.kernel.org/r/20220512041142.39501-5-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use kstrtobool rather than open coding "on" and "off" parsing in
mm/hugetlb_vmemmap.c, which is more powerful to handle all kinds of
parameters like 'Yy1Nn0' or [oO][NnFf] for "on" and "off".
Link: https://lkml.kernel.org/r/20220512041142.39501-4-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Optimizing HugeTLB vmemmap pages is not compatible with allocating memmap
on hot added memory. If "hugetlb_free_vmemmap=on" and
memory_hotplug.memmap_on_memory" are both passed on the kernel command
line, optimizing hugetlb pages takes precedence. However, the global
variable memmap_on_memory will still be set to 1, even though we will not
try to allocate memmap on hot added memory.
Also introduce mhp_memmap_on_memory() helper to move the definition of
"memmap_on_memory" to the scope of CONFIG_MHP_MEMMAP_ON_MEMORY. In the
next patch, mhp_memmap_on_memory() will also be exported to be used in
hugetlb_vmemmap.c.
Link: https://lkml.kernel.org/r/20220512041142.39501-3-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "add hugetlb_optimize_vmemmap sysctl", v11.
This series aims to add hugetlb_optimize_vmemmap sysctl to enable or
disable the feature of optimizing vmemmap pages associated with HugeTLB
pages.
This patch (of 4):
If the size of "struct page" is not the power of two but with the feature
of minimizing overhead of struct page associated with each HugeTLB is
enabled, then the vmemmap pages of HugeTLB will be corrupted after
remapping (panic is about to happen in theory). But this only exists when
!CONFIG_MEMCG && !CONFIG_SLUB on x86_64. However, it is not a
conventional configuration nowadays. So it is not a real word issue, just
the result of a code review.
But we cannot prevent anyone from configuring that combined configure.
This hugetlb_optimize_vmemmap should be disable in this case to fix this
issue.
Link: https://lkml.kernel.org/r/20220512041142.39501-1-songmuchun@bytedance.com
Link: https://lkml.kernel.org/r/20220512041142.39501-2-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb: 2M and
1G, but also CONT-PTE/PMD size: 64K and 32M if a 4K page size specified.
When unmapping a hugetlb page, we will get the relevant page table entry
by huge_pte_offset() only once to nuke it. This is correct for PMD or PUD
size hugetlb, since they always contain only one pmd entry or pud entry in
the page table.
However this is incorrect for CONT-PTE and CONT-PMD size hugetlb, since
they can contain several continuous pte or pmd entry with same page table
attributes, so we will nuke only one pte or pmd entry for this
CONT-PTE/PMD size hugetlb page.
And now try_to_unmap() is only passed a hugetlb page in the case where the
hugetlb page is poisoned. Which means now we will unmap only one pte
entry for a CONT-PTE or CONT-PMD size poisoned hugetlb page, and we can
still access other subpages of a CONT-PTE or CONT-PMD size poisoned
hugetlb page, which will cause serious issues possibly.
So we should change to use huge_ptep_clear_flush() to nuke the hugetlb
page table to fix this issue, which already considered CONT-PTE and
CONT-PMD size hugetlb.
We've already used set_huge_swap_pte_at() to set a poisoned swap entry for
a poisoned hugetlb page. Meanwhile adding a VM_BUG_ON() to make sure the
passed hugetlb page is poisoned in try_to_unmap().
Link: https://lkml.kernel.org/r/0a2e547238cad5bc153a85c3e9658cb9d55f9cac.1652270205.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/730ea4b6d292f32fb10b7a4e87dad49b0eb30474.1652147571.git.baolin.wang@linux.alibaba.com
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb: 2M and
1G, but also CONT-PTE/PMD size: 64K and 32M if a 4K page size specified.
When migrating a hugetlb page, we will get the relevant page table entry
by huge_pte_offset() only once to nuke it and remap it with a migration
pte entry. This is correct for PMD or PUD size hugetlb, since they always
contain only one pmd entry or pud entry in the page table.
However this is incorrect for CONT-PTE and CONT-PMD size hugetlb, since
they can contain several continuous pte or pmd entry with same page table
attributes. So we will nuke or remap only one pte or pmd entry for this
CONT-PTE/PMD size hugetlb page, which is not expected for hugetlb
migration. The problem is we can still continue to modify the subpages'
data of a hugetlb page during migrating a hugetlb page, which can cause a
serious data consistent issue, since we did not nuke the page table entry
and set a migration pte for the subpages of a hugetlb page.
To fix this issue, we should change to use huge_ptep_clear_flush() to nuke
a hugetlb page table, and remap it with set_huge_pte_at() and
set_huge_swap_pte_at() when migrating a hugetlb page, which already
considered the CONT-PTE or CONT-PMD size hugetlb.
[akpm@linux-foundation.org: fix nommu build]
[baolin.wang@linux.alibaba.com: fix build errors for !CONFIG_MMU]
Link: https://lkml.kernel.org/r/a4baca670aca637e7198d9ae4543b8873cb224dc.1652270205.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/ea5abf529f0997b5430961012bfda6166c1efc8c.1652147571.git.baolin.wang@linux.alibaba.com
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Originally, do num_poisoned_pages_inc() in memory failure routine, use
num_poisoned_pages_dec() to rollback the number if filtered/ cancelled.
Suggested by Naoya, do num_poisoned_pages_inc() only in action_result(),
this make this clear and simple.
Link: https://lkml.kernel.org/r/20220509105641.491313-6-pizhenwei@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
hwpoison filter is enabled by hwpoison-inject module, after removing this
module, hwpoison filter still works. What is worse, user can not find the
debugfs entries to know this.
Disable the hwpoison filter during removing hwpoison-inject module.
Link: https://lkml.kernel.org/r/20220509105641.491313-5-pizhenwei@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
hwpoison_filter is missing in the soft offline path, this leads an issue:
after enabling the corrupt filter, the user process still has a chance to
inject hwpoison fault by madvise(addr, len, MADV_SOFT_OFFLINE) at PFN
which is expected to reject.
Also do a minor change in comment of memory_failure().
Link: https://lkml.kernel.org/r/20220509105641.491313-4-pizhenwei@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Don't decrease the number of poisoned pages in page_alloc.c, let the
memory-failure.c do inc/dec poisoned pages only.
Also simplify unpoison_memory(), only decrease the number of
poisoned pages when:
- TestClearPageHWPoison() succeed
- put_page_back_buddy succeed
After decreasing, print necessary log.
Finally, remove clear_page_hwpoison() and unpoison_taken_off_page().
Link: https://lkml.kernel.org/r/20220509105641.491313-3-pizhenwei@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "memory-failure: fix hwpoison_filter", v2.
As well known, the memory failure mechanism handles memory corrupted
event, and try to send SIGBUS to the user process which uses this
corrupted page.
For the virtualization case, QEMU catches SIGBUS and tries to inject MCE
into the guest, and the guest handles memory failure again. Thus the
guest gets the minimal effect from hardware memory corruption.
The further step I'm working on:
1, try to modify code to decrease poisoned pages in a single place
(mm/memofy-failure.c: simplify num_poisoned_pages_dec in this series).
2, try to use page_handle_poison() to handle SetPageHWPoison() and
num_poisoned_pages_inc() together. It would be best to call
num_poisoned_pages_inc() in a single place too.
3, introduce memory failure notifier list in memory-failure.c: notify
the corrupted PFN to someone who registers this list. If I can
complete [1] and [2] part, [3] will be quite easy(just call notifier
list after increasing poisoned page).
4, introduce memory recover VQ for memory balloon device, and registers
memory failure notifier list. During the guest kernel handles memory
failure, balloon device gets notified by memory failure notifier list,
and tells the host to recover the corrupted PFN(GPA) by the new VQ.
5, host side remaps the corrupted page(HVA), and tells the guest side
to unpoison the PFN(GPA). Then the guest fixes the corrupted page(GPA)
dynamically.
This patch (of 5):
clear_hwpoisoned_pages() clears HWPoison flag and decreases the number of
poisoned pages, this actually works as part of memory failure.
Move this function from sparse.c to memory-failure.c, finally there is no
CONFIG_MEMORY_FAILURE in sparse.c.
Link: https://lkml.kernel.org/r/20220509105641.491313-1-pizhenwei@bytedance.com
Link: https://lkml.kernel.org/r/20220509105641.491313-2-pizhenwei@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Rename KASAN_KMALLOC_* shadow values to KASAN_SLAB_*, as they are used for
all slab allocations, not only for kmalloc.
Also rename KASAN_FREE_PAGE to KASAN_PAGE_FREE to be consistent with
KASAN_PAGE_REDZONE and KASAN_SLAB_FREE.
Link: https://lkml.kernel.org/r/bebcaf4eafdb0cabae0401a69c0af956aa87fcaa.1652111464.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
