IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Running event hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
in one of the system throws below error:
---Logs---
# perf list | grep hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=?/[Kernel PMU event]
# perf stat -v -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event is not supported by the kernel.
failed to read counter hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
Performance counter stats for 'system wide':
<not supported> hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
2.000700771 seconds time elapsed
The above error is because of the hcall failure as required
permission "Enable Performance Information Collection" is not set.
Based on current code, single_gpci_request function did not check the
error type incase hcall fails and by default returns EINVAL. But we can
have other reasons for hcall failures like H_AUTHORITY/H_PARAMETER with
detail_rc as GEN_BUF_TOO_SMALL, for which we need to act accordingly.
Fix this issue by adding new checks in the single_gpci_request and
h_gpci_event_init functions.
Result after fix patch changes:
# perf stat -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Error:
No permission to enable hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event.
Fixes: 220a0c609a ("powerpc/perf: Add support for the hv gpci (get performance counter info) interface")
Reported-by: Akanksha J N <akanksha@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240229122847.101162-1-kjain@linux.ibm.com
Base enablement patch to register performance monitoring
hardware support for Power11. Most of fields are copied
from power10_pmu struct for power11_pmu struct.
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240221044623.1598642-2-mpe@ellerman.id.au
- Add branch stack counters ABI extension to better capture
the growing amount of information the PMU exposes via
branch stack sampling. There's matching tooling support.
- Fix race when creating the nr_addr_filters sysfs file
- Add Intel Sierra Forest and Grand Ridge intel/cstate
PMU support.
- Add Intel Granite Rapids, Sierra Forest and Grand Ridge
uncore PMU support.
- Misc cleanups & fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=2O/5
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull performance events updates from Ingo Molnar:
- Add branch stack counters ABI extension to better capture the growing
amount of information the PMU exposes via branch stack sampling.
There's matching tooling support.
- Fix race when creating the nr_addr_filters sysfs file
- Add Intel Sierra Forest and Grand Ridge intel/cstate PMU support
- Add Intel Granite Rapids, Sierra Forest and Grand Ridge uncore PMU
support
- Misc cleanups & fixes
* tag 'perf-core-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Factor out topology_gidnid_map()
perf/x86/intel/uncore: Fix NULL pointer dereference issue in upi_fill_topology()
perf/x86/amd: Reject branch stack for IBS events
perf/x86/intel/uncore: Support Sierra Forest and Grand Ridge
perf/x86/intel/uncore: Support IIO free-running counters on GNR
perf/x86/intel/uncore: Support Granite Rapids
perf/x86/uncore: Use u64 to replace unsigned for the uncore offsets array
perf/x86/intel/uncore: Generic uncore_get_uncores and MMIO format of SPR
perf: Fix the nr_addr_filters fix
perf/x86/intel/cstate: Add Grand Ridge support
perf/x86/intel/cstate: Add Sierra Forest support
x86/smp: Export symbol cpu_clustergroup_mask()
perf/x86/intel/cstate: Cleanup duplicate attr_groups
perf/core: Fix narrow startup race when creating the perf nr_addr_filters sysfs file
perf/x86/intel: Support branch counters logging
perf/x86/intel: Reorganize attrs and is_visible
perf: Add branch_sample_call_stack
perf/x86: Add PERF_X86_EVENT_NEEDS_BRANCH_STACK flag
perf: Add branch stack counters
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: 885dcd709b ("powerpc/perf: Add nest IMC PMU support")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231126093719.1440305-1-chentao@kylinos.cn
To access hv-gpci kernel interface files data, the
"Enable Performance Information Collection" option has to be set
in hmc. Incase that option is not set and user try to read
the interface files, it should give error message as
operation not permitted.
Result of accessing added interface files with disabled
performance collection option:
[command]# cat processor_bus_topology
cat: processor_bus_topology: Operation not permitted
[command]# cat processor_config
cat: processor_config: Operation not permitted
[command]# cat affinity_domain_via_domain
cat: affinity_domain_via_domain: Operation not permitted
[command]# cat affinity_domain_via_virtual_processor
cat: affinity_domain_via_virtual_processor: Operation not permitted
[command]# cat affinity_domain_via_partition
Based on above result there is no error message when reading
affinity_domain_via_partition file because of missing
check for failed hcall. Fix this issue by adding
a check in the start of affinity_domain_via_partition_show
function, to return error incase hcall fails, with error type
other then H_PARAMETER.
Fixes: a15e0d6a69 ("powerpc/hv_gpci: Add sysfs file inside hv_gpci device to show affinity domain via partition information")
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231116122033.160964-1-kjain@linux.ibm.com
Currently, the additional information of a branch entry is stored in a
u64 space. With more and more information added, the space is running
out. For example, the information of occurrences of events will be added
for each branch.
Two places were suggested to append the counters.
https://lore.kernel.org/lkml/20230802215814.GH231007@hirez.programming.kicks-ass.net/
One place is right after the flags of each branch entry. It changes the
existing struct perf_branch_entry. The later ARCH specific
implementation has to be really careful to consistently pick
the right struct.
The other place is right after the entire struct perf_branch_stack.
The disadvantage is that the pointer of the extra space has to be
recorded. The common interface perf_sample_save_brstack() has to be
updated.
The latter is much straightforward, and should be easily understood and
maintained. It is implemented in the patch.
Add a new branch sample type, PERF_SAMPLE_BRANCH_COUNTERS, to indicate
the event which is recorded in the branch info.
The "u64 counters" may store the occurrences of several events. The
information regarding the number of events/counters and the width of
each counter should be exposed via sysfs as a reference for the perf
tool. Define the branch_counter_nr and branch_counter_width ABI here.
The support will be implemented later in the Intel-specific patch.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-1-kan.liang@linux.intel.com
When the PMU is disabled, MMCRA is not updated to disable BHRB and
instruction sampling. This can lead to those features remaining enabled,
which can slow down a real or emulated CPU.
Fixes: 1cade527f6 ("powerpc/perf: BHRB control to disable BHRB logic when not used")
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231018153423.298373-1-npiggin@gmail.com
The macro __SPIN_LOCK_INITIALIZER() is implementation specific. Users
that desire to initialize a spinlock in a struct must use
__SPIN_LOCK_UNLOCKED().
Use __SPIN_LOCK_UNLOCKED() for the spinlock_t in imc_global_refc.
Fixes: 76d588dddc ("powerpc/imc-pmu: Fix use of mutex in IRQs disabled section")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230309134831.Nz12nqsU@linutronix.de
This patch improves the performance of event alternative lookup by
replacing the previous linear search with a more efficient binary
search. This change reduces the time complexity for the search process
from O(n) to O(log(n)). A pre-sorted table of event values and their
corresponding indices has been introduced to expedite the search
process.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
[mpe: Call the array "presort*ed*_event_table", minor formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231013175714.2142775-1-visitorckw@gmail.com
Sparse reports several endianness warnings on variables and functions
that are consistently treated as big endian. There are no
multi-endianness shenanigans going on here so fix these low hanging
fruit up in one patch.
All changes are just type annotations; no endianness switching
operations are introduced by this patch.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231011053711.93427-7-bgray@linux.ibm.com
Sparse reports several uses of 0 for pointer arguments and comparisons.
Replace with NULL to better convey the intent. Remove entirely if a
comparison to follow the kernel style of implicit boolean conversions.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231011053711.93427-5-bgray@linux.ibm.com
Valid domain value is in range 1 to HV_PERF_DOMAIN_MAX. Current code has
check for domain value greater than or equal to HV_PERF_DOMAIN_MAX. But
the check for domain value 0 is missing.
Fix this issue by adding check for domain value 0.
Before:
# ./perf stat -v -e hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ sleep 1
Using CPUID 00800200
Control descriptor is not initialized
Error:
The sys_perf_event_open() syscall returned with 5 (Input/output error) for
event (hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/).
/bin/dmesg | grep -i perf may provide additional information.
Result from dmesg:
[ 37.819387] hv-24x7: hcall failed: [0 0x60040000 0x100 0] => ret
0xfffffffffffffffc (-4) detail=0x2000000 failing ix=0
After:
# ./perf stat -v -e hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ sleep 1
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ event is not supported by the kernel.
failed to read counter hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/
Fixes: ebd4a5a3eb ("powerpc/perf/hv-24x7: Minor improvements")
Reported-by: Krishan Gopal Sarawast <krishang@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Disha Goel <disgoel@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230825055601.360083-1-kjain@linux.ibm.com
CC arch/powerpc/perf/core-fsl-emb.o
arch/powerpc/perf/core-fsl-emb.c:675:6: error: no previous prototype for 'hw_perf_event_setup' [-Werror=missing-prototypes]
675 | void hw_perf_event_setup(int cpu)
| ^~~~~~~~~~~~~~~~~~~
Looks like fsl_emb was completely missed by commit 3f6da39053 ("perf:
Rework and fix the arch CPU-hotplug hooks")
So, apply same changes as commit 3f6da39053 ("perf: Rework and fix
the arch CPU-hotplug hooks") then commit 57ecde42cc ("powerpc/perf:
Convert book3s notifier to state machine callbacks")
While at it, also fix following error:
arch/powerpc/perf/core-fsl-emb.c: In function 'perf_event_interrupt':
arch/powerpc/perf/core-fsl-emb.c:648:13: error: variable 'found' set but not used [-Werror=unused-but-set-variable]
648 | int found = 0;
| ^~~~~
Fixes: 3f6da39053 ("perf: Rework and fix the arch CPU-hotplug hooks")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/603e1facb32608f88f40b7d7b9094adc50e7b2dc.1692349125.git.christophe.leroy@csgroup.eu
The hcall H_GET_PERF_COUNTER_INFO with counter request value as
AFFINITY_DOMAIN_INFORMATION_BY_PARTITION(0XB1), can be used to get
the system affinity domain via partition information. To expose the system
affinity domain via partition information, patch adds sysfs file called
"affinity_domain_via_partition" to the "/sys/devices/hv_gpci/interface/"
of hv_gpci pmu driver.
Add new entry for AFFINITY_DOMAIN_VIA_PAR in sysinfo_counter_request
array, which points to the counter request value
"affinity_domain_via_partition" in hv-gpci.c file. Also add a
new function called "affinity_domain_via_partition_result_parse" to parse
the hcall result and store it in output buffer.
The affinity_domain_via_partition sysfs file is only available for power10
and above platforms. Add a macro called
INTERFACE_AFFINITY_DOMAIN_VIA_PAR_ATTR, which points to the index of NULL
placeholder, for affinity_domain_via_partition attribute in
interface_attrs array. Also updated the value of INTERFACE_NULL_ATTR
macro in hv-gpci.c file.
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230729073455.7918-10-kjain@linux.ibm.com
The hcall H_GET_PERF_COUNTER_INFO with counter request value as
AFFINITY_DOMAIN_INFORMATION_BY_DOMAIN(0XB0), can be used to get
the system affinity domain via domain information. To expose the system
affinity domain via domain information, patch adds sysfs file called
"affinity_domain_via_domain" to the "/sys/devices/hv_gpci/interface/"
of hv_gpci pmu driver.
Add new entry for AFFINITY_DOMAIN_VIA_DOM in sysinfo_counter_request
array, which points to the counter request value
"affinity_domain_via_domain" in hv-gpci.c file.
The affinity_domain_via_domain sysfs file is only available for power10
and above platforms. Add a macro called
INTERFACE_AFFINITY_DOMAIN_VIA_DOM_ATTR, which points to the index of NULL
placeholder, for affinity_domain_via_domain attribute in interface_attrs
array. Also updated the value of INTERFACE_NULL_ATTR macro in hv-gpci.c
file.
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230729073455.7918-8-kjain@linux.ibm.com
The hcall H_GET_PERF_COUNTER_INFO with counter request value as
AFFINITY_DOMAIN_INFORMATION_BY_VIRTUAL_PROCESSOR(0XA0), can be used to get
the system affinity domain via virtual processor information. To expose
the system affinity domain via virtual processor information, patch adds
sysfs file called "affinity_domain_via_virtual_processor" to the
"/sys/devices/hv_gpci/interface/" of hv_gpci pmu driver.
The affinity_domain_via_virtual_processor sysfs file is only available for
power10 and above platforms. Add a macro called
INTERFACE_AFFINITY_DOMAIN_VIA_VP_ATTR, which points to the index of NULL
placeholder, for affinity_domain_via_virtual_processor attribute in
interface_attrs array. Also updated the value of INTERFACE_NULL_ATTR macro
in hv-gpci.c file.
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230729073455.7918-6-kjain@linux.ibm.com
The hcall H_GET_PERF_COUNTER_INFO with counter request value as
PROCESSOR_CONFIG(0X90), can be used to get the system
processor configuration information. To expose the system
processor config information, patch adds sysfs file called
"processor_config" to the "/sys/devices/hv_gpci/interface/"
of hv_gpci pmu driver.
Add enum and sysinfo_counter_request array to get required
counter request value in hv-gpci.c file.
Also add a new function called "sysinfo_device_attr_create",
which will create and return required device attribute to the
add_sysinfo_interface_files function.
The processor_config sysfs file is only available for power10
and above platforms. Add a new macro called
INTERFACE_PROCESSOR_CONFIG_ATTR, which points to the index of
NULL placefolder, for processor_config attribute in the interface_attrs
array. Also add macro INTERFACE_NULL_ATTR which points to index of NULL
attribute in interface_attrs array.
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230729073455.7918-4-kjain@linux.ibm.com
The hcall H_GET_PERF_COUNTER_INFO with counter request value as
PROCESSOR_BUS_TOPOLOGY(0XD0), can be used to get the system
topology information. To expose the system topology information,
patch adds sysfs file called "processor_bus_topology" to the
"/sys/devices/hv_gpci/interface/" of hv_gpci pmu driver.
Add macro for PROCESSOR_BUS_TOPOLOGY counter request value
in hv-gpci.c file. Also add a new function called
"systeminfo_gpci_request", to make the H_GET_PERF_COUNTER_INFO hcall
with added macro and populates the output buffer.
The processor_bus_topology sysfs file is only available for power10
and above platforms. Add a new function called
"add_sysinfo_interface_files", which will add processor_bus_topology
attribute in the interface_attrs array, only for power10 and
above platforms.
Also add macro INTERFACE_PROCESSOR_BUS_TOPOLOGY_ATTR in hv-gpci.c
file, which points to the index of NULL placefolder, for
processor_bus_topology attribute.
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230729073455.7918-2-kjain@linux.ibm.com
Unlike PVR_POWER8, etc ...., PVR_7450 represents a full PVR
value and not a family value.
To avoid confusion, do like E500 family and define the relevant
PVR_VER_xxxx values for the 7450 family:
0x8000 ==> 7450
0x8001 ==> 7455
0x8002 ==> 7447
0x8003 ==> 7447A
0x8004 ==> 7448
And use them to detect 7450 family for perf events.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302260657.7dM9Uwev-lkp@intel.com/
Fixes: ec3eb9d941 ("powerpc/perf: Use PVR rather than oprofile field to determine CPU version")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/99ca1da2e5a6cf82a8abf4bc034918e500e31781.1677513277.git.christophe.leroy@csgroup.eu
- Support for configuring secure boot with user-defined keys on PowerVM LPARs.
- Simplify the replay of soft-masked IRQs by making it non-recursive.
- Add support for KCSAN on 64-bit Book3S.
- Improvements to the API & code which interacts with RTAS (pseries firmware).
- Change 32-bit powermac to assign PCI bus numbers per domain by default.
- Some improvements to the 32-bit BPF JIT.
- Various other small features and fixes.
Thanks to: Anders Roxell, Andrew Donnellan, Andrew Jeffery, Benjamin Gray, Christophe
Leroy, Frederic Barrat, Ganesh Goudar, Geoff Levand, Greg Kroah-Hartman, Jan-Benedict
Glaw, Josh Poimboeuf, Kajol Jain, Laurent Dufour, Mahesh Salgaonkar, Mathieu Desnoyers,
Mimi Zohar, Murphy Zhou, Nathan Chancellor, Nathan Lynch, Nayna Jain, Nicholas Piggin,
Pali Rohár, Petr Mladek, Rohan McLure, Russell Currey, Sachin Sant, Sathvika Vasireddy,
Sourabh Jain, Stefan Berger, Stephen Rothwell, Sudhakar Kuppusamy.
-----BEGIN PGP SIGNATURE-----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=ECNb
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for configuring secure boot with user-defined keys on PowerVM
LPARs
- Simplify the replay of soft-masked IRQs by making it non-recursive
- Add support for KCSAN on 64-bit Book3S
- Improvements to the API & code which interacts with RTAS (pseries
firmware)
- Change 32-bit powermac to assign PCI bus numbers per domain by
default
- Some improvements to the 32-bit BPF JIT
- Various other small features and fixes
Thanks to Anders Roxell, Andrew Donnellan, Andrew Jeffery, Benjamin
Gray, Christophe Leroy, Frederic Barrat, Ganesh Goudar, Geoff Levand,
Greg Kroah-Hartman, Jan-Benedict Glaw, Josh Poimboeuf, Kajol Jain,
Laurent Dufour, Mahesh Salgaonkar, Mathieu Desnoyers, Mimi Zohar, Murphy
Zhou, Nathan Chancellor, Nathan Lynch, Nayna Jain, Nicholas Piggin, Pali
Rohár, Petr Mladek, Rohan McLure, Russell Currey, Sachin Sant, Sathvika
Vasireddy, Sourabh Jain, Stefan Berger, Stephen Rothwell, and Sudhakar
Kuppusamy.
* tag 'powerpc-6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (114 commits)
powerpc/pseries: Avoid hcall in plpks_is_available() on non-pseries
powerpc: dts: turris1x.dts: Set lower priority for CPLD syscon-reboot
powerpc/e500: Add missing prototype for 'relocate_init'
powerpc/64: Fix unannotated intra-function call warning
powerpc/epapr: Don't use wrteei on non booke
powerpc: Pass correct CPU reference to assembler
powerpc/mm: Rearrange if-else block to avoid clang warning
powerpc/nohash: Fix build with llvm-as
powerpc/nohash: Fix build error with binutils >= 2.38
powerpc/pseries: Fix endianness issue when parsing PLPKS secvar flags
macintosh: windfarm: Use unsigned type for 1-bit bitfields
powerpc/kexec_file: print error string on usable memory property update failure
powerpc/machdep: warn when machine_is() used too early
powerpc/64: Replace -mcpu=e500mc64 by -mcpu=e5500
powerpc/eeh: Set channel state after notifying the drivers
selftests/powerpc: Fix incorrect kernel headers search path
powerpc/rtas: arch-wide function token lookup conversions
powerpc/rtas: introduce rtas_function_token() API
powerpc/pseries/lpar: convert to papr_sysparm API
powerpc/pseries/hv-24x7: convert to papr_sysparm API
...
- Optimize perf_sample_data layout
- Prepare sample data handling for BPF integration
- Update the x86 PMU driver for Intel Meteor Lake
- Restructure the x86 uncore code to fix a SPR (Sapphire Rapids)
discovery breakage
- Fix the x86 Zhaoxin PMU driver
- Cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ztUT
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
- Optimize perf_sample_data layout
- Prepare sample data handling for BPF integration
- Update the x86 PMU driver for Intel Meteor Lake
- Restructure the x86 uncore code to fix a SPR (Sapphire Rapids)
discovery breakage
- Fix the x86 Zhaoxin PMU driver
- Cleanups
* tag 'perf-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86/intel/uncore: Add Meteor Lake support
x86/perf/zhaoxin: Add stepping check for ZXC
perf/x86/intel/ds: Fix the conversion from TSC to perf time
perf/x86/uncore: Don't WARN_ON_ONCE() for a broken discovery table
perf/x86/uncore: Add a quirk for UPI on SPR
perf/x86/uncore: Ignore broken units in discovery table
perf/x86/uncore: Fix potential NULL pointer in uncore_get_alias_name
perf/x86/uncore: Factor out uncore_device_to_die()
perf/core: Call perf_prepare_sample() before running BPF
perf/core: Introduce perf_prepare_header()
perf/core: Do not pass header for sample ID init
perf/core: Set data->sample_flags in perf_prepare_sample()
perf/core: Add perf_sample_save_brstack() helper
perf/core: Add perf_sample_save_raw_data() helper
perf/core: Add perf_sample_save_callchain() helper
perf/core: Save the dynamic parts of sample data size
x86/kprobes: Use switch-case for 0xFF opcodes in prepare_emulation
perf/core: Change the layout of perf_sample_data
perf/x86/msr: Add Meteor Lake support
perf/x86/cstate: Add Meteor Lake support
...
The new papr_sysparm API handles the details of system parameter
retrieval. Use that instead of open-coding the RTAS call, work area
management, and retries.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230125-b4-powerpc-rtas-queue-v3-17-26929c8cce78@linux.ibm.com
The ibm,get-system-parameter RTAS function may return -2 or 990x,
which indicate that the caller should try again. read_24x7_sys_info()
ignores this, allowing transient failures in reporting processor
module information.
Move the RTAS call into a coventional rtas_busy_delay()-based loop,
along with the parsing of results on success.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 8ba2142673 ("powerpc/hv-24x7: Add rtas call in hv-24x7 driver to get processor details")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230125-b4-powerpc-rtas-queue-v3-2-26929c8cce78@linux.ibm.com
Commit ec3eb9d941 ("powerpc/perf: Use PVR rather than
oprofile field to determine CPU version") added usage
of pvr value instead of oprofile field to determine the
platform. In hv-24x7 pmu driver code, pvr check uses PVR_POWER8
when assigning the interface version for power8 platform.
But power8 can also have other pvr values like PVR_POWER8E and
PVR_POWER8NVL. Hence the interface version won't be set
properly incase of PVR_POWER8E and PVR_POWER8NVL.
Fix this issue by adding the checks for PVR_POWER8E and
PVR_POWER8NVL as well.
Fixes: ec3eb9d941 ("powerpc/perf: Use PVR rather than oprofile field to determine CPU version")
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230131184804.220756-1-kjain@linux.ibm.com
The recent commit 76d588dddc ("powerpc/imc-pmu: Fix use of mutex in
IRQs disabled section") fixed warnings (and possible deadlocks) in the
IMC PMU driver by converting the locking to use spinlocks.
It also converted the init-time nest_init_lock to a spinlock, even
though it's not used at runtime in IRQ disabled sections or while
holding other spinlocks.
This leads to warnings such as:
BUG: sleeping function called from invalid context at include/linux/percpu-rwsem.h:49
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 6.2.0-rc2-14719-gf12cd06109f4-dirty #1
Hardware name: Mambo,Simulated-System POWER9 0x4e1203 opal:v6.6.6 PowerNV
Call Trace:
dump_stack_lvl+0x74/0xa8 (unreliable)
__might_resched+0x178/0x1a0
__cpuhp_setup_state+0x64/0x1e0
init_imc_pmu+0xe48/0x1250
opal_imc_counters_probe+0x30c/0x6a0
platform_probe+0x78/0x110
really_probe+0x104/0x420
__driver_probe_device+0xb0/0x170
driver_probe_device+0x58/0x180
__driver_attach+0xd8/0x250
bus_for_each_dev+0xb4/0x140
driver_attach+0x34/0x50
bus_add_driver+0x1e8/0x2d0
driver_register+0xb4/0x1c0
__platform_driver_register+0x38/0x50
opal_imc_driver_init+0x2c/0x40
do_one_initcall+0x80/0x360
kernel_init_freeable+0x310/0x3b8
kernel_init+0x30/0x1a0
ret_from_kernel_thread+0x5c/0x64
Fix it by converting nest_init_lock back to a mutex, so that we can call
sleeping functions while holding it. There is no interaction between
nest_init_lock and the runtime spinlocks used by the actual PMU routines.
Fixes: 76d588dddc ("powerpc/imc-pmu: Fix use of mutex in IRQs disabled section")
Tested-by: Kajol Jain<kjain@linux.ibm.com>
Reviewed-by: Kajol Jain<kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230130014401.540543-1-mpe@ellerman.id.au
When we saves the branch stack to the perf sample data, we needs to
update the sample flags and the dynamic size. To make sure this is
done consistently, add the perf_sample_save_brstack() helper and
convert all call sites.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230118060559.615653-5-namhyung@kernel.org
Current imc-pmu code triggers a WARNING with CONFIG_DEBUG_ATOMIC_SLEEP
and CONFIG_PROVE_LOCKING enabled, while running a thread_imc event.
Command to trigger the warning:
# perf stat -e thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/ sleep 5
Performance counter stats for 'sleep 5':
0 thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/
5.002117947 seconds time elapsed
0.000131000 seconds user
0.001063000 seconds sys
Below is snippet of the warning in dmesg:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 2869, name: perf-exec
preempt_count: 2, expected: 0
4 locks held by perf-exec/2869:
#0: c00000004325c540 (&sig->cred_guard_mutex){+.+.}-{3:3}, at: bprm_execve+0x64/0xa90
#1: c00000004325c5d8 (&sig->exec_update_lock){++++}-{3:3}, at: begin_new_exec+0x460/0xef0
#2: c0000003fa99d4e0 (&cpuctx_lock){-...}-{2:2}, at: perf_event_exec+0x290/0x510
#3: c000000017ab8418 (&ctx->lock){....}-{2:2}, at: perf_event_exec+0x29c/0x510
irq event stamp: 4806
hardirqs last enabled at (4805): [<c000000000f65b94>] _raw_spin_unlock_irqrestore+0x94/0xd0
hardirqs last disabled at (4806): [<c0000000003fae44>] perf_event_exec+0x394/0x510
softirqs last enabled at (0): [<c00000000013c404>] copy_process+0xc34/0x1ff0
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 36 PID: 2869 Comm: perf-exec Not tainted 6.2.0-rc2-00011-g1247637727f2 #61
Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV
Call Trace:
dump_stack_lvl+0x98/0xe0 (unreliable)
__might_resched+0x2f8/0x310
__mutex_lock+0x6c/0x13f0
thread_imc_event_add+0xf4/0x1b0
event_sched_in+0xe0/0x210
merge_sched_in+0x1f0/0x600
visit_groups_merge.isra.92.constprop.166+0x2bc/0x6c0
ctx_flexible_sched_in+0xcc/0x140
ctx_sched_in+0x20c/0x2a0
ctx_resched+0x104/0x1c0
perf_event_exec+0x340/0x510
begin_new_exec+0x730/0xef0
load_elf_binary+0x3f8/0x1e10
...
do not call blocking ops when !TASK_RUNNING; state=2001 set at [<00000000fd63e7cf>] do_nanosleep+0x60/0x1a0
WARNING: CPU: 36 PID: 2869 at kernel/sched/core.c:9912 __might_sleep+0x9c/0xb0
CPU: 36 PID: 2869 Comm: sleep Tainted: G W 6.2.0-rc2-00011-g1247637727f2 #61
Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV
NIP: c000000000194a1c LR: c000000000194a18 CTR: c000000000a78670
REGS: c00000004d2134e0 TRAP: 0700 Tainted: G W (6.2.0-rc2-00011-g1247637727f2)
MSR: 9000000000021033 <SF,HV,ME,IR,DR,RI,LE> CR: 48002824 XER: 00000000
CFAR: c00000000013fb64 IRQMASK: 1
The above warning triggered because the current imc-pmu code uses mutex
lock in interrupt disabled sections. The function mutex_lock()
internally calls __might_resched(), which will check if IRQs are
disabled and in case IRQs are disabled, it will trigger the warning.
Fix the issue by changing the mutex lock to spinlock.
Fixes: 8f95faaac5 ("powerpc/powernv: Detect and create IMC device")
Reported-by: Michael Petlan <mpetlan@redhat.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
[mpe: Fix comments, trim oops in change log, add reported-by tags]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230106065157.182648-1-kjain@linux.ibm.com
- Add powerpc qspinlock implementation optimised for large system scalability and
paravirt. See the merge message for more details.
- Enable objtool to be built on powerpc to generate mcount locations.
- Use a temporary mm for code patching with the Radix MMU, so the writable mapping is
restricted to the patching CPU.
- Add an option to build the 64-bit big-endian kernel with the ELFv2 ABI.
- Sanitise user registers on interrupt entry on 64-bit Book3S.
- Many other small features and fixes.
Thanks to: Aboorva Devarajan, Angel Iglesias, Benjamin Gray, Bjorn Helgaas, Bo Liu, Chen
Lifu, Christoph Hellwig, Christophe JAILLET, Christophe Leroy, Christopher M. Riedl, Colin
Ian King, Deming Wang, Disha Goel, Dmitry Torokhov, Finn Thain, Geert Uytterhoeven,
Gustavo A. R. Silva, Haowen Bai, Joel Stanley, Jordan Niethe, Julia Lawall, Kajol Jain,
Laurent Dufour, Li zeming, Miaoqian Lin, Michael Jeanson, Nathan Lynch, Naveen N. Rao,
Nayna Jain, Nicholas Miehlbradt, Nicholas Piggin, Pali Rohár, Randy Dunlap, Rohan McLure,
Russell Currey, Sathvika Vasireddy, Shaomin Deng, Stephen Kitt, Stephen Rothwell, Thomas
Weißschuh, Tiezhu Yang, Uwe Kleine-König, Xie Shaowen, Xiu Jianfeng, XueBing Chen, Yang
Yingliang, Zhang Jiaming, ruanjinjie, Jessica Yu, Wolfram Sang.
-----BEGIN PGP SIGNATURE-----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=7k3p
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add powerpc qspinlock implementation optimised for large system
scalability and paravirt. See the merge message for more details
- Enable objtool to be built on powerpc to generate mcount locations
- Use a temporary mm for code patching with the Radix MMU, so the
writable mapping is restricted to the patching CPU
- Add an option to build the 64-bit big-endian kernel with the ELFv2
ABI
- Sanitise user registers on interrupt entry on 64-bit Book3S
- Many other small features and fixes
Thanks to Aboorva Devarajan, Angel Iglesias, Benjamin Gray, Bjorn
Helgaas, Bo Liu, Chen Lifu, Christoph Hellwig, Christophe JAILLET,
Christophe Leroy, Christopher M. Riedl, Colin Ian King, Deming Wang,
Disha Goel, Dmitry Torokhov, Finn Thain, Geert Uytterhoeven, Gustavo A.
R. Silva, Haowen Bai, Joel Stanley, Jordan Niethe, Julia Lawall, Kajol
Jain, Laurent Dufour, Li zeming, Miaoqian Lin, Michael Jeanson, Nathan
Lynch, Naveen N. Rao, Nayna Jain, Nicholas Miehlbradt, Nicholas Piggin,
Pali Rohár, Randy Dunlap, Rohan McLure, Russell Currey, Sathvika
Vasireddy, Shaomin Deng, Stephen Kitt, Stephen Rothwell, Thomas
Weißschuh, Tiezhu Yang, Uwe Kleine-König, Xie Shaowen, Xiu Jianfeng,
XueBing Chen, Yang Yingliang, Zhang Jiaming, ruanjinjie, Jessica Yu,
and Wolfram Sang.
* tag 'powerpc-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (181 commits)
powerpc/code-patching: Fix oops with DEBUG_VM enabled
powerpc/qspinlock: Fix 32-bit build
powerpc/prom: Fix 32-bit build
powerpc/rtas: mandate RTAS syscall filtering
powerpc/rtas: define pr_fmt and convert printk call sites
powerpc/rtas: clean up includes
powerpc/rtas: clean up rtas_error_log_max initialization
powerpc/pseries/eeh: use correct API for error log size
powerpc/rtas: avoid scheduling in rtas_os_term()
powerpc/rtas: avoid device tree lookups in rtas_os_term()
powerpc/rtasd: use correct OF API for event scan rate
powerpc/rtas: document rtas_call()
powerpc/pseries: unregister VPA when hot unplugging a CPU
powerpc/pseries: reset the RCU watchdogs after a LPM
powerpc: Take in account addition CPU node when building kexec FDT
powerpc: export the CPU node count
powerpc/cpuidle: Set CPUIDLE_FLAG_POLLING for snooze state
powerpc/dts/fsl: Fix pca954x i2c-mux node names
cxl: Remove unnecessary cxl_pci_window_alignment()
selftests/powerpc: Fix resource leaks
...
Based on getPerfCountInfo v1.018 documentation, some of the
hv_gpci events were deprecated for platform firmware that
supports counter_info_version 0x8 or above.
Fix the hv_gpci event list by adding a new attribute group
called "hv_gpci_event_attrs_v6" and a "ENABLE_EVENTS_COUNTERINFO_V6"
macro to enable these events for platform firmware
that supports counter_info_version 0x6 or below. And assigning
the hv_gpci event list based on output counter info version
of underlying plaform.
Fixes: 97bf264018 ("powerpc/perf/hv-gpci: add the remaining gpci requests")
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221130174513.87501-1-kjain@linux.ibm.com
Most callers just want to validate an arbitrary kernel stack pointer,
some need a particular size. Make the size case the exceptional one
with an extra function.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221127124942.1665522-15-npiggin@gmail.com
This is a count of longs from the stack pointer to the regs marker.
Rename it to make it more distinct from the other byte offsets. It
can be derived from the byte offset definitions just added.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221127124942.1665522-10-npiggin@gmail.com
This is a common offset that currently uses the overloaded
STACK_FRAME_OVERHEAD constant. It's easier to read and more
flexible to use a specific regs offset for this.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221127124942.1665522-8-npiggin@gmail.com
The interrupt frame detection and loads from the hypothetical pt_regs
are not bounds-checked. The next-frame validation only bounds-checks
STACK_FRAME_OVERHEAD, which does not include the pt_regs. Add another
test for this.
The user could set r1 to be equal to the address matching the first
interrupt frame - STACK_INT_FRAME_SIZE, which is in the previous page
due to the kernel redzone, and induce the kernel to load the marker from
there. Possibly this could cause a crash at least. If the user could
induce the previous page to contain a valid marker, then it might be
able to direct perf to read specific memory addresses in a way that
could be transmitted back to the user in the perf data.
Fixes: 20002ded4d ("perf_counter: powerpc: Add callchain support")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221127124942.1665522-4-npiggin@gmail.com
There have been various issues and limitations with the way perf uses
(task) contexts to track events. Most notable is the single hardware
PMU task context, which has resulted in a number of yucky things (both
proposed and merged).
Notably:
- HW breakpoint PMU
- ARM big.little PMU / Intel ADL PMU
- Intel Branch Monitoring PMU
- AMD IBS PMU
- S390 cpum_cf PMU
- PowerPC trace_imc PMU
*Current design:*
Currently we have a per task and per cpu perf_event_contexts:
task_struct::perf_events_ctxp[] <-> perf_event_context <-> perf_cpu_context
^ | ^ | ^
`---------------------------------' | `--> pmu ---'
v ^
perf_event ------'
Each task has an array of pointers to a perf_event_context. Each
perf_event_context has a direct relation to a PMU and a group of
events for that PMU. The task related perf_event_context's have a
pointer back to that task.
Each PMU has a per-cpu pointer to a per-cpu perf_cpu_context, which
includes a perf_event_context, which again has a direct relation to
that PMU, and a group of events for that PMU.
The perf_cpu_context also tracks which task context is currently
associated with that CPU and includes a few other things like the
hrtimer for rotation etc.
Each perf_event is then associated with its PMU and one
perf_event_context.
*Proposed design:*
New design proposed by this patch reduce to a single task context and
a single CPU context but adds some intermediate data-structures:
task_struct::perf_event_ctxp -> perf_event_context <- perf_cpu_context
^ | ^ ^
`---------------------------' | |
| | perf_cpu_pmu_context <--.
| `----. ^ |
| | | |
| v v |
| ,--> perf_event_pmu_context |
| | |
| | |
v v |
perf_event ---> pmu ----------------'
With the new design, perf_event_context will hold all events for all
pmus in the (respective pinned/flexible) rbtrees. This can be achieved
by adding pmu to rbtree key:
{cpu, pmu, cgroup, group_index}
Each perf_event_context carries a list of perf_event_pmu_context which
is used to hold per-pmu-per-context state. For example, it keeps track
of currently active events for that pmu, a pmu specific task_ctx_data,
a flag to tell whether rotation is required or not etc.
Additionally, perf_cpu_pmu_context is used to hold per-pmu-per-cpu
state like hrtimer details to drive the event rotation, a pointer to
perf_event_pmu_context of currently running task and some other
ancillary information.
Each perf_event is associated to it's pmu, perf_event_context and
perf_event_pmu_context.
Further optimizations to current implementation are possible. For
example, ctx_resched() can be optimized to reschedule only single pmu
events.
Much thanks to Ravi for picking this up and pushing it towards
completion.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Co-developed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221008062424.313-1-ravi.bangoria@amd.com
- PMU driver updates:
- Add AMD Last Branch Record Extension Version 2 (LbrExtV2)
feature support for Zen 4 processors.
- Extend the perf ABI to provide branch speculation information,
if available, and use this on CPUs that have it (eg. LbrExtV2).
- Improve Intel PEBS TSC timestamp handling & integration.
- Add Intel Raptor Lake S CPU support.
- Add 'perf mem' and 'perf c2c' memory profiling support on
AMD CPUs by utilizing IBS tagged load/store samples.
- Clean up & optimize various x86 PMU details.
- HW breakpoints:
- Big rework to optimize the code for systems with hundreds of CPUs and
thousands of breakpoints:
- Replace the nr_bp_mutex global mutex with the bp_cpuinfo_sem
per-CPU rwsem that is read-locked during most of the key operations.
- Improve the O(#cpus * #tasks) logic in toggle_bp_slot()
and fetch_bp_busy_slots().
- Apply micro-optimizations & cleanups.
- Misc cleanups & enhancements.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LcGg
-----END PGP SIGNATURE-----
Merge tag 'perf-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf events updates from Ingo Molnar:
"PMU driver updates:
- Add AMD Last Branch Record Extension Version 2 (LbrExtV2) feature
support for Zen 4 processors.
- Extend the perf ABI to provide branch speculation information, if
available, and use this on CPUs that have it (eg. LbrExtV2).
- Improve Intel PEBS TSC timestamp handling & integration.
- Add Intel Raptor Lake S CPU support.
- Add 'perf mem' and 'perf c2c' memory profiling support on AMD CPUs
by utilizing IBS tagged load/store samples.
- Clean up & optimize various x86 PMU details.
HW breakpoints:
- Big rework to optimize the code for systems with hundreds of CPUs
and thousands of breakpoints:
- Replace the nr_bp_mutex global mutex with the bp_cpuinfo_sem
per-CPU rwsem that is read-locked during most of the key
operations.
- Improve the O(#cpus * #tasks) logic in toggle_bp_slot() and
fetch_bp_busy_slots().
- Apply micro-optimizations & cleanups.
- Misc cleanups & enhancements"
* tag 'perf-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
perf/hw_breakpoint: Annotate tsk->perf_event_mutex vs ctx->mutex
perf: Fix pmu_filter_match()
perf: Fix lockdep_assert_event_ctx()
perf/x86/amd/lbr: Adjust LBR regardless of filtering
perf/x86/utils: Fix uninitialized var in get_branch_type()
perf/uapi: Define PERF_MEM_SNOOPX_PEER in kernel header file
perf/x86/amd: Support PERF_SAMPLE_PHY_ADDR
perf/x86/amd: Support PERF_SAMPLE_ADDR
perf/x86/amd: Support PERF_SAMPLE_{WEIGHT|WEIGHT_STRUCT}
perf/x86/amd: Support PERF_SAMPLE_DATA_SRC
perf/x86/amd: Add IBS OP_DATA2 DataSrc bit definitions
perf/mem: Introduce PERF_MEM_LVLNUM_{EXTN_MEM|IO}
perf/x86/uncore: Add new Raptor Lake S support
perf/x86/cstate: Add new Raptor Lake S support
perf/x86/msr: Add new Raptor Lake S support
perf/x86: Add new Raptor Lake S support
bpf: Check flags for branch stack in bpf_read_branch_records helper
perf, hw_breakpoint: Fix use-after-free if perf_event_open() fails
perf: Use sample_flags for raw_data
perf: Use sample_flags for addr
...
For PERF_SAMPLE_BRANCH_STACK sample type, different branch_sample_type
ie branch filters are supported. The branch filters are requested via
event attribute "branch_sample_type". Multiple branch filters can be
passed in event attribute. eg:
$ perf record -b -o- -B --branch-filter any,ind_call true
None of the Power PMUs support having multiple branch filters at
the same time. Branch filters for branch stack sampling is set via MMCRA
IFM bits [32:33]. But currently when requesting for multiple filter
types, the "perf record" command does not report any error.
eg:
$ perf record -b -o- -B --branch-filter any,save_type true
$ perf record -b -o- -B --branch-filter any,ind_call true
The "bhrb_filter_map" function in PMU driver code does the validity
check for supported branch filters. But this check is done for single
filter. Hence "perf record" will proceed here without reporting any
error.
Fix power_pmu_event_init() to return EOPNOTSUPP when multiple branch
filters are requested in the event attr.
After the fix:
$ perf record --branch-filter any,ind_call -- ls
Error:
cycles: PMU Hardware doesn't support sampling/overflow-interrupts.
Try 'perf stat'
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Disha Goel<disgoel@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
[mpe: Tweak comment and change log wording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220921145255.20972-1-atrajeev@linux.vnet.ibm.com
Use helper macros to access global variables, and place them in .data
sections rather than in .toc. Putting addresses in TOC is not required
because the kernel is linked with a single TOC.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220926034057.2360083-3-npiggin@gmail.com
Forward declare all syscall handler prototypes where a generic prototype
is not provided in either linux/syscalls.h or linux/compat.h in
asm/syscalls.h. This is required for compile-time type-checking for
syscall handlers, which is implemented later in this series.
32-bit compatibility syscall handlers are expressed in terms of types in
ppc32.h. Expose this header globally.
Signed-off-by: Rohan McLure <rmclure@linux.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use standard include guard naming for syscalls_32.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220921065605.1051927-17-rmclure@linux.ibm.com
Use the new sample_flags to indicate whether the data_src field is
filled by the PMU driver.
Remove the data_src field from the perf_sample_data_init() to minimize
the number of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-6-kan.liang@linux.intel.com
Use the new sample_flags to indicate whether the weight field is filled
by the PMU driver.
Remove the weight field from the perf_sample_data_init() to minimize the
number of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-5-kan.liang@linux.intel.com
Use the new sample_flags to indicate whether the branch stack is filled
by the PMU driver.
Remove the br_stack from the perf_sample_data_init() to minimize the number
of cache lines touched.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220901130959.1285717-4-kan.liang@linux.intel.com
In update_events_in_group(), of_find_node_by_phandle() will return
a node pointer with refcount incremented. The reference should be
dropped with of_node_put() in the failure path or when it is not used
anymore.
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20220618071353.4059000-1-windhl@126.com
Commit 6320e693d9 ("powerpc/perf: Add support for caps under sysfs in
powerpc") added support for caps under sysfs in powerpc. This added caps
directory to: /sys/bus/event_source/devices/cpu/ for power8, power9,
power10 and generic compat PMU in respective PMU driver code.
For power10, it is added under "power10_pmu_attr_groups". But
for DD1 version, attr_groups are defined under dd1 array:
"power10_pmu_attr_groups_dd1". Since caps is not added for DD1,
it fails to include "cpu/caps" in DD1 model.
The issue was observed while booting power10 pseries with qemu version
6, but not observed with qemu version 7. This is because qemu version 7
uses a DD 2.0 CPU model.
Below is the trace log:
Can't update unknown attr grp name: cpu/caps^M
------------[ cut here ]------------^M
Failed to register pmu: cpu, reason -22^M
WARNING: CPU: 1 PID: 1 at kernel/events/core.c:13427 perf_event_sysfs_init+0xbc/0x108^M
Modules linked in:^M
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc2-00111-g6320e693d98c #148^M
NIP: c0000000020391f4 LR: c0000000020391f0 CTR: c0000000008c9c30^M
REGS: c0000000044c38c0 TRAP: 0700 Not tainted (5.19.0-rc2-00111-g6320e693d98c)^M
MSR: 8000000002029033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 48000281 XER: 20040000^M
CFAR: c00000000013feac IRQMASK: 0 ^M
GPR00: c0000000020391f0 c0000000044c3b60 c00000000283db00 0000000000000027 ^M
GPR04: 80000000ffffe0a8 0000000000000000 0000000000000004 00000000fdcd0000 ^M
GPR08: 0000000000000027 c0000000ffe07e08 0000000000000001 0000000000000000 ^M
GPR12: c00000000035dd90 c0000000fffff300 c000000000012478 0000000000000000 ^M
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 ^M
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 ^M
GPR24: c000000002003480 0000000000000007 c0000000012a78d0 c000000001170a80 ^M
GPR28: c0000000026c4df8 c0000000026c4e68 0000000000000000 c0000000025a8628 ^M
NIP [c0000000020391f4] perf_event_sysfs_init+0xbc/0x108^M
LR [c0000000020391f0] perf_event_sysfs_init+0xb8/0x108^M
Call Trace:^M
[c0000000044c3b60] [c0000000020391f0] perf_event_sysfs_init+0xb8/0x108 (unreliable)^M
[c0000000044c3bf0] [c000000000011ec4] do_one_initcall+0x64/0x2d0^M
[c0000000044c3cd0] [c0000000020049fc] kernel_init_freeable+0x338/0x3e0^M
[c0000000044c3db0] [c0000000000124a0] kernel_init+0x30/0x1a0^M
[c0000000044c3e10] [c00000000000cd54] ret_from_kernel_thread+0x5c/0x64^M
Instruction dump:^M
813f0038 2c090000 4180002c 7fe3fb78 4a3280c5 2c030000 7c651b78 41820018 ^M
e89f0030 7f63db78 4a106c59 60000000 <0fe00000> ebff0000 4bffffb4 39200001 ^M
---[ end trace 0000000000000000 ]---^M
Fix it by adding caps for dd1 attr_groups in power10 PMU driver.
Fixes: 6320e693d9 ("powerpc/perf: Add support for caps under sysfs in powerpc")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
[mpe: Update change log to mention qemu 7 DD2.0 CPU model]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220728163746.85062-1-atrajeev@linux.vnet.ibm.com
Currently the perf CPU backend drivers detect what CPU they're on using
cur_cpu_spec->oprofile_cpu_type.
Although that works, it's a bit crufty to be using oprofile related fields,
especially seeing as oprofile is more or less unused these days.
It also means perf is reliant on the fragile logic in setup_cpu_spec()
which detects when we're using a logical PVR and copies back the PMU
related fields from the raw CPU entry. So lets check the PVR directly.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[chleroy: Added power10 and fixed checkpatch issues]
Reviewed-and-tested-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-and-tested-By: Kajol Jain <kjain@linux.ibm.com> [For 24x7 side changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20c0ee7f99dbf0dbf8658df6b39f84753e6db1ef.1657204631.git.christophe.leroy@csgroup.eu
Add caps support under "/sys/bus/event_source/devices/<pmu>/"
for powerpc. This directory can be used to expose some of the
specific features that powerpc PMU supports to the user.
Example: pmu_name. The name of PMU registered will depend on
platform, say power9 or power10 or it could be Generic Compat
PMU.
Currently the only way to know which is the registered
PMU is from the dmesg logs. But clearing the dmesg will make it
difficult to know exact PMU backend used. And even extracting
from dmesg will be complicated, as we need to parse the dmesg
logs and add filters for pmu name. Whereas by exposing it via
caps will make it easy as we just need to directly read it from
the sysfs.
Add a caps directory to /sys/bus/event_source/devices/cpu/
for power8, power9, power10 and generic compat PMU in respective
PMU driver code. Update the pmu_name file under caps folder
in core-book3s using "attr_update".
The information exposed currently:
- pmu_name : Underlying PMU name from the driver
Example result with power9 pmu:
# ls /sys/bus/event_source/devices/cpu/caps
pmu_name
# cat /sys/bus/event_source/devices/cpu/caps/pmu_name
POWER9
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220520084630.15181-1-atrajeev@linux.vnet.ibm.com
When booting on a machine that uses the compat pmu driver we see this:
[ 0.071192] GENERIC_COMPAT performance monitor hardware support registered
Which is a bit shouty. Give it a nicer name.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220610044006.2095806-1-joel@jms.id.au
struct perf_event_attr supports exclude counting of idle task.
This is sent to kernel via perf_event_attr.exclude_idle and
in perf tool, user can use ":I" event modifier to enable this
for specific event.
Monitor Mode Control Register 2 (MMCR2) SPR has control bits
for each PMCs to freeze counting based on the Control Register
CTRL[RUN] state. CTRL[RUN] is not set when idle task is
running. Patch adds a check for event attr.exclude_idle to
set MMCR2[FCnWAIT] bit.
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210429050208.266619-1-maddy@linux.ibm.com
