IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
For hdmi-codec, we need to update struct hdmi_codec_ops,
and all its users in the same time.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87d055xxj2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.
If the board has 2 Type-C ports, the DP driver get the phy id from
devm_of_phy_get_by_index, and then control this switch according to
this id. But some others board only has one Type-C port, it may be PHY 0
or PHY 1. The dts node id can not tell us the correct PHY id. Hence move
this switch to PHY driver, the PHY driver can distinguish between PHY 0
and PHY 1, and then write the correct register bit.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[The phy-changes are in the phy-tree now and the cdn-dp wasn't
enabled at all so far, so this change can go through drm-misc
alone without causing issues when testing drm-misc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216120956.19034-6-enric.balletbo@collabora.com
Force vop output mode on encoder driver seem not a good idea,
EDP, HDMI, DisplayPort all have 10bit input on rk3399,
On non-10bit vop, vop 8bit output bit[0-7] connect to the
encoder high 8bit [2-9].
So force RGB10 to RGB888 on vop driver would be better.
And another problem, EDP check crtc id on atomic_check,
but encoder maybe NULL, so out_mode configure would fail,
it cause edp no display.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495885416-22216-1-git-send-email-mark.yao@rock-chips.com
Pointer for Markus's image conversion work.
We need this so we can merge all the pretty drm graphs for 4.12.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Sometimes the Dock is disconnected, but cdn_dp_encoder_disable is not
triggered by DRM. For example, unplug the Dock in console mode, and
re-plug it again, the cdn_dp_event_work will try to get the sink count
of Dock, since the DP is still active. But the Dock has been powered
down, it need re-power on, and wait for a while until it is ready to
DPCD communication.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
If no monitor is connected, suspend/resume cycles result in firmware
load errors because the driver attempts to load the firmware while
the system is in suspend state. This results in a kernel warning and
traceback.
Loading the firmware during boot fixes the problem. Note that we can not
just call schedule_work conditionally in cdn_dp_pd_event() if the insertion
status changed. The problem would still be seen if a monitor is connected
for the first time during suspend.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Add support for cdn DP controller which is embedded in the rk3399
SoCs. The DP is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work,
please put the firmware file to /lib/firmware/rockchip/dptx.bin. The
uCPU in charge of aux communication and link training, the host use
mailbox to communicate with the ucpu.
The dclk pin_pol of vop must not be invert for DP.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
[seanpaul fixed up some races between the worker and modeset]
[seanpaul squashed ~15 commits from chromium.org gerrit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[groeck fixed compilation errors when building as module]
Signed-off-by: Guenter Roeck <groeck@chromium.org>
