IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Getting the mvm station out of station id requires dereferencing
the station id to get ieee80211_sta, then checking for pointer
validity and only then extract mvm station out.
Given that there are helpers to do it - use them instead of
duplicating the code whenever we need only mvm station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.
Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.
There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.
This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.
When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.
When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Leaving ucode_loaded to true after stop_device() has been called
is a recipe for problems. Flows that are not sync'ed with the
driver life cycle (like debugfs hooks and thermal hooks) must
check that the firmware is loaded before they interact with it.
Therefore we need to keep this variable updated with the real
status of the firmware.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when entering D3 with WOWLAN configured, we enable in the
configuration flags beacon storing, and do not disable beacon
filtering, and do not wake up from a magic packet.
Having both enabled is wrong (should not have both enabled),
and causes problems in the RX queues in the FW, causing
the FW not to recognize the magic packet when it comes.
Disable beacon storing in wowlan configuration.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If protocol offloading is configured, the fw might generate some
frames (e.g. arp response) on its own during d3/d0i3.
On d3/d0i3 exit the driver queries the updated PN (if relevant),
and updates its keys (for the d0i3 case, this is done by
iwl_mvm_d0i3_exit_work(), which is scheduled on d0i3 exit)
While in d0i3, iwlmvm defers tx frames until d0i3 exit, and
then continues their processing.
This is problematic with TKIP, since the frame's PN has already
been set at this stage (in contrast to CCMP, where the PN is
being set only later on), so both the frame's PN and the upcoming
PN update (from d0i3 exit work) might be wrong.
Fix it by moving the TX PN assignment (for TKIP) to the driver,
similarly to CCMP.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when the driver is configured with wowlan parameters, and enters
D3 mode, the driver switches the FW image to D3, and when it exists
suspend, it reloads the D0 image.
If the firmware supports the consolidation of the D0 & D3 images there is
no need to load the D3 image on suspend, and no need to reload the D0
image on resume.
Do not switch images on suspend / resume, for firmwares that support
consolidated images.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
gtkdata->mvm wasn't set in iwl_mvm_d0i3_update_keys,
resulting in kernel panic in some flows (when mvm
is actually used...)
Fixes: a3f7ba5c8825 ("iwlwifi: update key params on d0i3 entrance/exit")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As we're working on multi-queue RX, we want to parallelise checking
the PN in order to avoid having to serialise the RX processing.
It may seem that doing parallel PN checking is insecure, but it turns
out to be OK because queue assignment is done based on the data in the
frame (IP/TCP) and thus cannot be manipulated by an attacker, since
the data is encrypted and must first have been decrypted successfully.
There are some corner cases, in particular when the peer starts using
fragmentation which redirects the packet to the default queue. However
this redirection is remembered (for the STA, per TID) and thus cannot
be exploited by an attacker either.
Leave checking on the default queue (queue 0) to mac80211, since we
get fragmented packets there and those are subject to stricter checks
during reassembly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to let the fw do offloading properly, we need
to provide various key data (e.g. PN).
Configure the params on d0i3 entrance, and update them
back on d0i3 exit.
Since d3 code is now called in d0i3 which requires runtime
pm only, make d3.0 depend on CONFIG_PM (rather than
CONFIG_PM_SLEEP), and add required #ifdefs and wrappers
where needed, so both CONFIG_PM=n and CONFIG_PM_RUNTIME=n
configurations will build correctly.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Firmware will support filtering multicast L3 packets.
The L3 filtering is configured by the WOWLAN_CONFIG command.
All flags should be enabled by default.
Older firmware is not affected as it does not look into
this field.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of keeping the fw_key_table bits set when the keys are removed
(i.e. in D3 entry or HW_RESTART flows), clear them and set them again
only when the keys have been successfully re-added. This makes the
bitmask more closely tied to the actual firmware programming.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
RFC4862 states that "In all cases, a node MUST NOT respond to
a Neighbor Solicitation for a tentative address".
Currently the driver configures the NS offload and does not wait
for address to become permanent, thus violating the RFC.
Just removing the address from the address list is not good enough
for all cases, since the NS messages are needed for the duplicate
address detection and should not be discarded.
For d0i3 disable NS offload. Put tentative address in the address
list so the NS packet will not be filtered out by ucode.
For D3 the platform will not wake from NS packets - so enable
NS offload while removing the tentative address from the list.
Given that now NS offload might be disabled, and that the ucode
uses the IP data for other puroposes (L3 filtering) add two
independent flags indicating if IPv4\IPv6 data is valid.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d0i3_mode variable is used to distinguish between transports that
handle d0i3 entry during suspend by themselves (i.e. the slave
transports) and those which rely on the op_mode layer to do it. The
reason why the former do it by themselves is that they need to
transition from d0i3 in runtime_suspend into d0i3 in system-wide
suspend and this transition needs to happen before the op_mode's
suspend flow is called.
The wowlan_d0i3 element is also a bit confusing, because it just
reflects the wowlan->any value for the trans to understand. This is a
bit unclear in the code and not generic enough for future use.
To make it clearer and to generalize the platform power mode settings,
introduce two variables to indicate the platform power management
modes used by the transport.
Additionally, in order not to take too big a step in one patch, treat
this new variables semantically in the same way as the old d0i3_mode
element, introducing a iwl_mvm_enter_d0i3_on_suspend() function to
help with that.
This commit also adds the foundation for a new concept where the
firmware configuration state (i.e. D0, D3 or D0i3) is abstracted from
the platform PM mode we are in (i.e. runtime suspend or system-wide
suspend).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
commit 9a4c830007817e ("iwlwifi: mvm: refactor d3 key
update functions") refactored some code into
iwl_mvm_wowlan_config_key_params() function, but the
return value was never checked, and not all the function
flows returned valid values. fix it.
Fixes: ac8ef0ce38de ("iwlwifi: mvm: refactor d3 key update functions")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the wifi wakes up the system, we need to report it via calling
pm_wakeup_event for lucid sleep. This is so userspace knowns that the
wifi woke up the system via the /sys/power/wakeup_type sysfs interface.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to reuse the key update logic for d0i3
as well.
Add some parameters to deal with the constraints
implied by the d0i3 flow (specifically, support
non-SYNC commands, and don't take mutexes that
might deadlock).
Change some commands to be ASYNC, in order
to simplify locking a bit.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure. Remove it.
Fixes: dbb04b0d29f8 ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
