IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The base address of the audio bus and pdm device are different
between the g12 and sm1 SoC families. Overwriting the reg property
only would leave with confusing node names on the sm1.
Move the audio related devices to the g12 dtsi. The appropriate nodes
will be created for the sm1 later on.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The power domain declared in the g12a and g12b dtsi are the same.
Move the declaration of these power domains in the g12 common dtsi.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
While the sm1 is very close to the g12a/b family, somethings apply
differently on the g12a/b and not the sm1. This introduce a new layer
of dtsi for part which apply to the g12a and g12b but not the sm1.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The register region size initially is too small to access all
the fifo registers.
Fixes: c59b7fe5aafd ("arm64: dts: meson: g12a: add audio fifos")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The register region size initially is too small to access all
the fifo registers.
Fixes: f2b8f6a93357 ("arm64: dts: meson-axg: add audio fifos")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Set the appropriate gpio interrupt controller compatible for the
sm1 SoC family. This newer version of the controller can now
trig irq on both edge of the input signal
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The commit d4609acce187 ("arm64: dts: meson-sm1-sei610: enable DVFS")
incorrectly removed the chosen node and the stdout-path property.
Add these back.
Fixes: d4609acce187 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables DVFS for the Amlogic SM1 based SEI610 board by:
- Adding the SM1 SoC OPPs taken from the vendor tree
- Selecting the SM1 Clock controller instead of the G12A one
- Adding the CPU rail regulator, PWM and OPPs for each CPU nodes.
Each power supply can achieve 0.69V to 1.05V using a single PWM
output clocked at 666KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of the cpu cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the Amlogic SM1 based Khadas VIM3L, sharing all the same features
as the G12B based VIM3, but:
- a different DVFS support since only a single cluster is available
- audio is still not available on SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
To prepare support of the Amlogic SM1 based Khadas VIM3, move the non-G12B
specific nodes (all except DVFS and Audio) to a new meson-khadas-vim3.dtsi
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the reset to the TDM formatters of the g12a. This helps
with channel mapping when a playback/capture uses more than 1 lane.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller dedicated to audio clocks also provides reset lines
on the g12 SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables DVFS for the Amlogic SM1 based SEI610 board by:
- Adding the SM1 SoC OPPs taken from the vendor tree
- Selecting the SM1 Clock controller instead of the G12A one
- Adding the CPU rail regulator, PWM and OPPs for each CPU nodes.
Each power supply can achieve 0.69V to 1.05V using a single PWM
output clocked at 666KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of the cpu cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-tx3mini keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-wetek-play2 keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-wetek-hub keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-x96max keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-odroid keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the USB properties for the Amlogic SM1 Based SEI610 Board in order to
support the USB DRD Type-C port and the USB3 Type A port.
The USB DRD Type-C controller uses the ID signal to toggle the USB role
between the DWC3 Host controller and the DWC2 Device controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the HDMI support nodes for the Amlogic SM1 Based SEI610 Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Replace the VPU-centric power domain controller by the generic system-wide
Everything-Else power domain controller and setup the right power-domains
properties on the VPU, Ethernet & USB nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[khilman: minor subject edit: add dts]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-p201.dt.yaml: ethernet@c9410000: snps,reset-delays-us: [[0, 10000, 1000000]] is too short
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: /: 'model' is a required property
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-g12a-x96-max.dt.yaml: /: compatible: ['amediatech,x96-max', 'amlogic,u200', 'amlogic,g12a'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-g12a-u200.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
meson-g12a-sei510.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-axg-s400.dt.yaml: mailbox@ff63c404: compatible:0: 'amlogic,meson-gx-mhu' is not one of ['amlogic,meson-gxbb-mhu']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: ethernet-phy@8: compatible: ['ethernet-phy-id0181.4400', 'ethernet-phy-ieee802.3-c22'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: periphs@c8834000: $nodename:0: 'periphs@c8834000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
meson-gxl-s805x-libretech-ac.dt.yaml: periphs@c8834000: $nodename:0: 'periphs@c8834000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: mailbox@404: compatible:0: 'amlogic,meson-gx-mhu' is not one of ['amlogic,meson-gxbb-mhu']
meson-gxl-s805x-libretech-ac.dt.yaml: mailbox@404: compatible:0: 'amlogic,meson-gx-mhu' is not one of ['amlogic,meson-gxbb-mhu']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: watchdog@98d0: compatible:0: 'amlogic,meson-gx-wdt' is not one of ['amlogic,meson-gxbb-wdt']
meson-gxl-s805x-libretech-ac.dt.yaml: watchdog@98d0: compatible:0: 'amlogic,meson-gx-wdt' is not one of ['amlogic,meson-gxbb-wdt']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: spi@8c80: compatible:0: 'amlogic,meson-gx-spifc' is not one of ['amlogic,meson6-spifc', 'amlogic,meson-gxbb-spifc']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: reset-controller@4404: compatible:0: 'amlogic,meson-gx-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: vpu@d0100000: reg-names: Additional items are not allowed ('dmc' was unexpected)
meson-gxl-s805x-libretech-ac.dt.yaml: vpu@d0100000: reg-names: ['vpu', 'hhi', 'dmc'] is too long
The 'dmc' register area was replaced by the amlogic,canvas property
which was introduced in commit f1726043426c73 ("arm64: dts: meson-gx:
add dmcbus and canvas nodes.") and commit cf34287986d0b6 ("arm64: dts:
meson-gx: Add canvas provider node to the vpu")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-axg-s400.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-axg-s400.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-g12a-u200.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-g12a-u200.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-gxbb-nanopi-k2.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too long
meson-gxl-s805x-libretech-ac.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too lon
while here, also drop the redundant reg property from meson-gxl.dtsi
because it had the same value as meson-gx.dtsi from which it inherits.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable DVFS for the Odroid-N2 by setting the clock, OPP and supply
for each cores of each CPU clusters.
The first cluster uses the "VDDCPU_B" power supply, and the second
cluster uses the "VDDCPU_A" power supply.
Each power supply can achieve 0.73V to 1.01V using 2 distinct PWM
outputs clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of each cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM3 uses the Amlogic S922X or A311S SoC, both based on the
Amlogic G12B SoC family, on a board with the same form factor as the
VIM/VIM2 models. It ships in two variants; basic and
pro which differ in RAM and eMMC size:
- 2GB (basic) or 4GB (pro) LPDDR4 RAM
- 16GB (basic) or 32GB (pro) eMMC 5.1 storage
- 16MB SPI flash
- 10/100/1000 Base-T Ethernet
- AP6398S Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 1x USB 2.0 + 1x USB 3.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 3x LED's (1x red, 1x blue, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- M2 socket with PCIe, USB, ADC & I2C
- 40pin GPIO Header
- 1x micro SD card slot
A common meson-g12b-khadas-vim3.dtsi is added to support both S922X and
A311D SoCs supported by two variants of the board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Arm per-CPU architected timers stop ticking in suspend, when the
SCP powers down the CPUs. Flag that in the DT.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson g12b ships with a low-speed (S922X) and high-speed (A311D) variant
so remove cpu_opp_table nodes in meson-g12b.dtsi and create two new dtsi
that can be included in device-specific dts files. Opp points were taken
from the vendor BSP kernel.
Also make meson-g12b-odroid-n2.dts include the new meson-g12b-s922x.dtsi.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables the video decoder for GXBB, GXL and GXM chips
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the base video decoder node compatible with the meson vdec driver,
for GX* chips.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheets in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the OPP table taken from the HardKernel Odroid-N2 DTS.
The Amlogic G12B SoC seems to available in 2 types :
- low-speed: Cortex-A73 Cluster up to 1,704GHz
- high-speed: Cortex-A73 Cluster up to 2.208GHz
The Cortex-A73 Cluster can be clocked up to 1,896GHz for both types.
The Vendor Amlogic A311D OPP table are slighly different, with lower
voltages than the HardKernel S922X tables but seems to be high-speed type.
This adds the conservative OPP table with the S922X higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an HardKernel Odroid-N2 board
running the arm64 cpuburn at [1] and cycling between all the possible
cpufreq translations for both clusters and checking the final frequency
using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
