IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch.pl warnings:
drivers/usb/core/config.c:989: CHECK:ALLOC_SIZEOF_STRUCT: Prefer kzalloc(sizeof(*bos)...) over kzalloc(sizeof(struct usb_bos_descriptor)...)
drivers/usb/core/config.c:1010: CHECK:ALLOC_SIZEOF_STRUCT: Prefer kzalloc(sizeof(*dev->bos)...) over kzalloc(sizeof(struct usb_host_bos)...)
Signed-off-by: Robert Greener <rob@robgreener.com>
Link: https://lore.kernel.org/r/20211001151350.ijiexr3ebwvypmdd@shortbread
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USBDEVFS_CONTROL and USBDEVFS_BULK ioctls invoke
usb_start_wait_urb(), which contains an uninterruptible wait with a
user-specified timeout value. If timeout value is very large and the
device being accessed does not respond in a reasonable amount of time,
the kernel will complain about "Task X blocked for more than N
seconds", as found in testing by syzbot:
INFO: task syz-executor.0:8700 blocked for more than 143 seconds.
Not tainted 5.14.0-rc7-syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor.0 state:D stack:23192 pid: 8700 ppid: 8455 flags:0x00004004
Call Trace:
context_switch kernel/sched/core.c:4681 [inline]
__schedule+0xc07/0x11f0 kernel/sched/core.c:5938
schedule+0x14b/0x210 kernel/sched/core.c:6017
schedule_timeout+0x98/0x2f0 kernel/time/timer.c:1857
do_wait_for_common+0x2da/0x480 kernel/sched/completion.c:85
__wait_for_common kernel/sched/completion.c:106 [inline]
wait_for_common kernel/sched/completion.c:117 [inline]
wait_for_completion_timeout+0x46/0x60 kernel/sched/completion.c:157
usb_start_wait_urb+0x167/0x550 drivers/usb/core/message.c:63
do_proc_bulk+0x978/0x1080 drivers/usb/core/devio.c:1236
proc_bulk drivers/usb/core/devio.c:1273 [inline]
usbdev_do_ioctl drivers/usb/core/devio.c:2547 [inline]
usbdev_ioctl+0x3441/0x6b10 drivers/usb/core/devio.c:2713
...
To fix this problem, this patch replaces usbfs's calls to
usb_control_msg() and usb_bulk_msg() with special-purpose code that
does essentially the same thing (as recommended in the comment for
usb_start_wait_urb()), except that it always uses a killable wait and
it uses GFP_KERNEL rather than GFP_NOIO.
Reported-and-tested-by: syzbot+ada0f7d3d9fd2016d927@syzkaller.appspotmail.com
Suggested-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210903175312.GA468440@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user submits a control URB via usbfs, the user supplies the
bRequestType value and the kernel uses it to compute the pipe value.
However, do_proc_control() performs this computation incorrectly in
the case where the bRequestType direction bit is set to USB_DIR_IN and
the URB's transfer length is 0: The pipe's direction is also set to IN
but it should be OUT, which is the direction the actual transfer will
use regardless of bRequestType.
Commit 5cc59c418f ("USB: core: WARN if pipe direction != setup
packet direction") added a check to compare the direction bit in the
pipe value to a control URB's actual direction and to WARN if they are
different. This can be triggered by the incorrect computation
mentioned above, as found by syzbot.
This patch fixes the computation, thus avoiding the WARNing.
Reported-and-tested-by: syzbot+72af3105289dcb4c055b@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210712185436.GB326369@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A type of inconsistency that can show up in control URBs is when the
setup packet's wLength value does not match the URB's
transfer_buffer_length field. The two should always be equal;
differences could lead to information leaks or undefined behavior for
OUT transfers or overruns for IN transfers.
This patch adds a test for such mismatches during URB submission. If
the test fails, the submission is rejected with a -EBADR error code
(which is not used elsewhere in the USB core), and a debugging message
is logged for people interested in tracking down these errors.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210526153244.GA1400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the "removable" attribute from USB to core in order to allow it to be
supported by other subsystem / buses. Individual buses that want to support
this attribute can populate the removable property of the device while
enumerating it with the 3 possible values -
- "unknown"
- "fixed"
- "removable"
Leaving the field unchanged (i.e. "not supported") would mean that the
attribute would not show up in sysfs for that device. The UAPI (location,
symantics etc) for the attribute remains unchanged.
Move the "removable" attribute from USB to the device core so it can be
used by other subsystems / buses.
By default, devices do not have a "removable" attribute in sysfs.
If a subsystem or bus driver wants to support a "removable" attribute, it
should call device_set_removable() before calling device_register() or
device_add(), e.g.:
device_set_removable(dev, DEVICE_REMOVABLE);
device_register(dev);
The possible values and the resulting sysfs attribute contents are:
DEVICE_REMOVABLE_UNKNOWN -> "unknown"
DEVICE_REMOVABLE -> "removable"
DEVICE_FIXED -> "fixed"
Convert the USB "removable" attribute to use this new device core
functionality. There should be no user-visible change in the location or
semantics of attribute for USB devices.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-1-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control URB is submitted, the direction indicated by URB's pipe
member is supposed to match the direction indicated by the setup
packet's bRequestType member. A mismatch could lead to trouble,
depending on which field the host controller drivers use for
determining the actual direction.
This shouldn't ever happen; it would represent a careless bug in a
kernel driver somewhere. This patch adds a dev_WARN_ONCE to let
people know about the potential problem.
Suggested-by: "Geoffrey D. Bennett" <g@b4.vu>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210522021623.GB1260282@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been almost twenty years since the interface "private data" pointer
was removed in favour of using the driver-data pointer of struct device.
Let's rename the driver-data parameter of usb_driver_claim_interface()
so that it better reflects how it's used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210318155406.22399-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices cannot perform DMA and hence have no dma_mask set in their
device structure. Therefore importing dmabuf into a USB-based driver
fails, which breaks joining and mirroring of display in X11.
For USB devices, pick the associated USB controller as attachment device.
This allows the DRM import helpers to perform the DMA setup. If the DMA
controller does not support DMA transfers, we're out of luck and cannot
import. Our current USB-based DRM drivers don't use DMA, so the actual
DMA device is not important.
Tested by joining/mirroring displays of udl and radeon under Gnome/X11.
v8:
* release dmadev if device initialization fails (Noralf)
* fix commit description (Noralf)
v7:
* fix use-before-init bug in gm12u320 (Dan)
v6:
* implement workaround in DRM drivers and hold reference to
DMA device while USB device is in use
* remove dev_is_usb() (Greg)
* collapse USB helper into usb_intf_get_dma_device() (Alan)
* integrate Daniel's TODO statement (Daniel)
* fix typos (Greg)
v5:
* provide a helper for USB interfaces (Alan)
* add FIXME item to documentation and TODO list (Daniel)
v4:
* implement workaround with USB helper functions (Greg)
* use struct usb_device->bus->sysdev as DMA device (Takashi)
v3:
* drop gem_create_object
* use DMA mask of USB controller, if any (Daniel, Christian, Noralf)
v2:
* move fix to importer side (Christian, Daniel)
* update SHMEM and CMA helpers for new PRIME callbacks
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 6eb0233ec2 ("usb: don't inherity DMA properties for USB devices")
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210303133229.3288-1-tzimmermann@suse.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
