IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
DMA burst support is added to improve performance in EHCI data
transfer. The USB EHCI controller on Exynos SoCs can use INCR16,
INCR8, and INCR4 mode. These modes of INSNREG00 register should
be set in order to enable DMA burst transfer. This feature is
also related to AHB spec.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
This reverts commit 79857e8e7b1ba740f8025b540f1e171c9a0a5d31.
To quote Shengzhou Liu:
I'm sorry, please don't apply this patch.
It appears not only on P1022 platform.
There will be more breaks on other platforms regarding
CTRL_PHY_CLK_VALID bit.
I will post a new patch with well compatibility on all
platforms as soon as I get necessary confirmations.
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checking of CTRL_PHY_CLK_VALID bit break on some platform on which
there is not USB CTRL_PHY_CLK_VALID bit.
- P1023/P3041/P5020 etc,have this bit
- P3060/4080/PSC913x do have this bit, but not mentioned in RM.
- P1022(perhaps and other) has no this bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.
Includes fixes from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ehci driver is mainly designed to support host controller found on
Marvell PXA and MMP Soc series.
Add the dependence to avoid the potential build failure which may
include two EHCI controller drivers.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes uses of hcd->state and replaces hcd->state with
ohci->rh_state field.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB UTMI PHY is not enable, writing to portsc register will lead to
kernel hang during boot up.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When build i.mx platform with imx_v6_v7_defconfig, and after adding
USB Gadget support, it has below build error:
CC drivers/usb/host/fsl-mph-dr-of.o
drivers/usb/host/fsl-mph-dr-of.c: In function 'fsl_usb2_device_register':
drivers/usb/host/fsl-mph-dr-of.c:97: error: 'struct pdev_archdata'
has no member named 'dma_mask'
It has discussed at: http://www.spinics.net/lists/linux-usb/msg57302.html
For PowerPC, there is dma_mask at struct pdev_archdata, but there is
no dma_mask at struct pdev_archdata for ARM. The pdev_archdata is
related to specific platform, it should NOT be accessed by
cross platform drivers, like USB.
The code for pdev_archdata should be useless, as for PowerPC,
it has already gotten the value for pdev->dev.dma_mask at function
arch_setup_pdev_archdata of arch/powerpc/kernel/setup-common.c.
Tested-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the usb_disabled() check to the probe function and get rid of the
rather pointless message on module load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a MPC8xxx was being used, 'have_sysif_regs' should be set and
it should setup cache snooping for all the 4GB space on both PPC32
and PPC64.
Signed-off-by: Pan Jiafei <Jiafei.Pan@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ehci-mv.c can cover Marvell PXA and MMP series including PXA168,
so this driver seems redundant now.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Cc: <tanmay.upadhyay@einfochips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pull in the xhci changes and the other fixes and device id
updates that were done in Linus's tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
not all platforms will use all of those ehci_*
symbols on their hc_driver structure. Sometimes
we might need to provide a modified version of
a certain method or not provide it at all, as is
the case with OMAPs which don't support port handoff
feature.
Whenever we compile a kernel for an OMAP board with
EHCI enabled, we get compile warnings:
drivers/usb/host/ehci-hub.c:1079: warning: 'ehci_relinquish_port' \
defined but not used
drivers/usb/host/ehci-hub.c:1088: warning: 'ehci_port_handed_over' \
defined but not used
In order to cleanup those warnings, we're adding
__maybe_unused annotation to those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved). Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.
When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain. The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.
However, the parent hubs in the resumed path will not set their link
state change bit. Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller. Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.
First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes. Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).
Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed. When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.
We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver. This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.
Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.
This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached). The other cases will be covered
in a second patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs have a different remote wakeup policy than USB 2.0 hubs.
USB 2.0 hubs, once they have remote wakeup enabled, will always send
remote wakes when anything changes on a port.
However, USB 3.0 hubs have a per-port remote wake up policy that is off
by default. The Set Feature remote wake mask can be changed for any
port, enabling remote wakeup for a connect, disconnect, or overcurrent
event, much like EHCI and xHCI host controller "wake on" port status
bits. The bits are cleared to zero on the initial hub power on, or
after the hub has been reset.
Without this patch, when a USB 3.0 hub gets suspended, it will not send
a remote wakeup on device connect or disconnect. This would show up to
the user as "dead ports" unless they ran lsusb -v (since newer versions
of lsusb use the sysfs files, rather than sending control transfers).
Change the hub driver's suspend method to enable remote wake up for
disconnect, connect, and overcurrent for all ports on the hub. Modify
the xHCI driver's roothub code to handle that request, and set the "wake
on" bits in the port status registers accordingly.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the USB 3.0 hub support went in, I disabled selective suspend for
all external USB 3.0 hubs because they used a different mechanism to
enable remote wakeup. In fact, other USB 3.0 devices that could signal
remote wakeup would have been prevented from going into suspend because
they would have stalled the SetFeature Device Remote Wakeup request.
This patch adds support for the USB 3.0 way of enabling remote wake up
(with a SetFeature Function Suspend request), and enables selective
suspend for all hubs during hub_probe. It assumes that all USB 3.0 have
only one "function" as defined by the interface association descriptor,
which is true of all the USB 3.0 devices I've seen so far. FIXME if
that turns out to change later.
After a device signals a remote wakeup, it is supposed to send a Device
Notification packet to the host controller, signaling which function
sent the remote wakeup. The host can then put any other functions back
into function suspend. Since we don't have support for function suspend
(and no devices currently support it), we'll just assume the hub
function will resume the device properly when it received the port
status change notification, and simply ignore any device notification
events from the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI roothubs go through slightly different port state machines when
either a device initiates a remote wakeup and signals resume, or when
the host initiates a resume.
According to section 4.19.1.2.13 of the xHCI 1.0 spec, on host-initiated
resume, the xHC port state machine automatically goes through the U3Exit
state into the U0 state, setting the port link state change (PLC) bit in
the process.
When a device initiates resume, the xHCI port state machine goes into
the "Resume" state and sets the PLC bit. Then the xHCI driver writes U0
into the port link state register to transition the port to U0 from the
Resume state.
We can't be sure the device is actually in the U0 state until we receive
the next port status change event with the PLC bit set. We really don't
want khubd to be polling the roothub port status bits until the device
is really in U0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code to set the device removable bits in the USB 2.0 roothub
descriptor was accidentally looking at the USB 3.0 port registers
instead of the USB 2.0 registers. This can cause an oops if there are
more USB 2.0 registers than USB 3.0 registers.
This should be backported to kernels as old as 2.6.39, that contain the
commit 4bbb0ace9a3de8392527e3c87926309d541d3b00 "xhci: Return a USB 3.0
hub descriptor for USB3 roothub."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This is done to resolve a merge conflict with:
drivers/usb/class/cdc-wdm.c
and to better handle future patches for this driver as it is under
active development at the moment.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Netlogic XLP SoC's on-chip USB controller appears as a PCI
USB device, but does not need the EHCI/OHCI handoff done in
usb/host/pci-quirks.c.
The pci-quirks.c is enabled for all vendors and devices, and is
enabled if USB and PCI are configured.
If we do not skip the qurik handling on XLP, the readb() call in
ehci_bios_handoff() will cause a crash since byte access is not
supported for EHCI registers in XLP.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when missing USB PHY clock, kernel booting up will halt during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hang in this case.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish Kconfig text by providing the Freescale family name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk8m8JEACgkQMUfUDdst+ymCFQCeNhTHopHy1PQbuCDwk8bSH4DW
1/YAn2k0YaaCrOo0HCzOslAVX18vGnWl
=TNNB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Here are a bunch of USB patches for 3.3-rc1.
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
uwb & wusb: fix kconfig error
USB: Realtek cr: fix autopm scheduling while atomic
USB: ftdi_sio: Add more identifiers
xHCI: Cleanup isoc transfer ring when TD length mismatch found
usb: musb: omap2430: minor cleanups.
qcaux: add more Pantech UML190 and UML290 ports
Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
usb: mv-otg - Fix build if CONFIG_USB is not set
USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
usb: add support for STA2X11 host driver
drivers: usb: Fix dependency for USB_HWA_HCD
kernel-doc: fix new warning in usb.h
USB: OHCI: fix new compiler warnings
usb: serial: kobil_sct: fix compile warning:
drivers/usb/host/ehci-fsl.c: add missing iounmap
USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
USB: cdc-wdm: use two mutexes to allow simultaneous read and write
USB: cdc-wdm: updating desc->length must be protected by spin_lock
USB: usbsevseg: fix max length
...
When a TD length mismatch is found during isoc TRB enqueue, it directly
returns -EINVAL. However, isoc transfer is partially enqueued at this time,
and the ring should be cleared.
This should be backported to kernels as old as 2.6.36, which contain the
commit 522989a27c7badb608155b1f1dea3487ed431f74 "xhci: Fix failed
enqueue in the middle of isoch TD."
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This reverts commit 0dd2b62ada6f911fbd13e98e98f57f4edc42c604.
It causes a bunch of Kconfig errors:
drivers/usb/host/Kconfig:559:error: recursive dependency detected!
drivers/usb/host/Kconfig:559: symbol USB_HWA_HCD depends on UWB
drivers/uwb/Kconfig:5: symbol UWB is selected by USB_WUSB
drivers/usb/wusbcore/Kconfig:4: symbol USB_WUSB is selected by USB_HWA_HCD
showing that this really wasn't the correct fix at all.
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use ehci_setup() in ehci_ls1x_reset().
The Loongson1x SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use INCR8 mode for system bus interface of the USB controller
on MPC512x. This is a work-around for the AHB bus lock up
problem observed on MPC512x when there is heavy simultaneous
PATA write or network (FEC) activity.
See also "12.4 The USB controller can issue transactions that lock
up the AHB bus under certain conditions" in MPC5121e (M36P) Errata.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.ue>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 689d6eac ("USB: UHCI: add native scatter-gather support(v1))
added sg support to uhci but forgot to set the sg_table so this feature
remained unused.
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following build warning:
warning: (USB_HWA_HCD) selects UWB_HWA which has unmet direct dependencies (UWB && USB)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1515) fixes some unavoidably dumb compiler warnings:
CC [M] drivers/usb/renesas_usbhs/mod.o
In file included from drivers/usb/host/ohci-hcd.c:101:0:
drivers/usb/host/ohci-dbg.c: In function ‘fill_registers_buffer’:
drivers/usb/host/ohci-dbg.c:656:2: warning: the comparison will always evaluate as ‘true’ for the address of ‘next’ will never be NULL [-Waddress]
drivers/usb/host/ohci-dbg.c:675:3: warning: the comparison will always evaluate as ‘true’ for the address of ‘next’ will never be NULL [-Waddress]
Instead of trying to fix the macro to work under all cirumstances,
just add a second macro for use in cases where the "next" argument is
the address of a local variable.
Unfortunately the macro cannot be replaced by a real subroutine,
because there's no va_list version of ohci_dbg() or dev_dbg().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
