IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add documentation for pm capabilties such as MMC_PM_KEEP_POWER
and MMC_PM_WAKE_SDIO_IRQ.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the SD/MMC host controller found
on Wondermedia 8xxx series SoCs, currently supported under
arm/arch-vt8500.
A binding document is also included, based on mmc.txt with
additional properties.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
Merely reorganizing documentation. No functional changes. It makes more
sense for the gpio-leds binding to be grouped with other led bindings
than with gpio drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The compatible property in device tree "crypto" node has been enhanced
to provide SEC ERA information to the applications.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Implement ONE_REG interface for EPCR register adding KVM_REG_PPC_EPCR to
the list of ONE_REG PPC supported registers.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency, use get/put_user]
Signed-off-by: Alexander Graf <agraf@suse.de>
A new ioctl, KVM_PPC_GET_HTAB_FD, returns a file descriptor. Reads on
this fd return the contents of the HPT (hashed page table), writes
create and/or remove entries in the HPT. There is a new capability,
KVM_CAP_PPC_HTAB_FD, to indicate the presence of the ioctl. The ioctl
takes an argument structure with the index of the first HPT entry to
read out and a set of flags. The flags indicate whether the user is
intending to read or write the HPT, and whether to return all entries
or only the "bolted" entries (those with the bolted bit, 0x10, set in
the first doubleword).
This is intended for use in implementing qemu's savevm/loadvm and for
live migration. Therefore, on reads, the first pass returns information
about all HPTEs (or all bolted HPTEs). When the first pass reaches the
end of the HPT, it returns from the read. Subsequent reads only return
information about HPTEs that have changed since they were last read.
A read that finds no changed HPTEs in the HPT following where the last
read finished will return 0 bytes.
The format of the data provides a simple run-length compression of the
invalid entries. Each block of data starts with a header that indicates
the index (position in the HPT, which is just an array), the number of
valid entries starting at that index (may be zero), and the number of
invalid entries following those valid entries. The valid entries, 16
bytes each, follow the header. The invalid entries are not explicitly
represented.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix documentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
This updates the IRQdomain documentation a bit, by adding a more
verbose explanation to why we need this, and by adding some
extended documentation of the irq_domain_simple() usecase.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The "powervr" prefix which is currently described as "Imagination
Technologies" isn't really appropriate for non-PowerVR hardware, so
deprecate it, changing the description of "powervr" to "PowerVR
(deprecated, use img)", and add a separate "img" prefix for "Imagination
Technologies Ltd.".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ./kernel/ksysfs.c defines 'profiling' w/o 'profile' like
"KERNEL_ATTR_RW(profiling)". We need to synchronize the content between ksys.c
source and kernel doc.
Signed-off-by: Hyeonjun Lim <hjoon0510@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Very quiet release for ASoC really:
- Standardisation of the logging.
- DT and dmaengine support for Atmel.
- Support for Wolfson ADSP cores.
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2irt
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.8
Very quiet release for ASoC really:
- Standardisation of the logging.
- DT and dmaengine support for Atmel.
- Support for Wolfson ADSP cores.
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090.
Conflicts:
arch/x86/kernel/ptrace.c
Pull the latest RCU tree from Paul E. McKenney:
" The major features of this series are:
1. A first version of no-callbacks CPUs. This version prohibits
offlining CPU 0, but only when enabled via CONFIG_RCU_NOCB_CPU=y.
Relaxing this constraint is in progress, but not yet ready
for prime time. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/724, and are at branch rcu/nocb.
2. Changes to SRCU that allows statically initialized srcu_struct
structures. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/296, and are at branch rcu/srcu.
3. Restructuring of RCU's debugfs output. These commits were posted
to LKML at https://lkml.org/lkml/2012/10/30/341, and are at
branch rcu/tracing.
4. Additional CPU-hotplug/RCU improvements, posted to LKML at
https://lkml.org/lkml/2012/10/30/327, and are at branch rcu/hotplug.
Note that the commit eliminating __stop_machine() was judged to
be too-high of risk, so is deferred to 3.9.
5. Changes to RCU's idle interface, most notably a new module
parameter that redirects normal grace-period operations to
their expedited equivalents. These were posted to LKML at
https://lkml.org/lkml/2012/10/30/739, and are at branch rcu/idle.
6. Additional diagnostics for RCU's CPU stall warning facility,
posted to LKML at https://lkml.org/lkml/2012/10/30/315, and
are at branch rcu/stall. The most notable change reduces the
default RCU CPU stall-warning time from 60 seconds to 21 seconds,
so that it once again happens sooner than the softlockup timeout.
7. Documentation updates, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/280, and are at branch rcu/doc.
A couple of late-breaking changes were posted at
https://lkml.org/lkml/2012/11/16/634 and
https://lkml.org/lkml/2012/11/16/547.
8. Miscellaneous fixes, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/309, along with a late-breaking
change posted at Fri, 16 Nov 2012 11:26:25 -0800 with message-ID
<20121116192625.GA447@linux.vnet.ibm.com>, but which lkml.org
seems to have missed. These are at branch rcu/fixes.
9. Finally, a fix for an lockdep-RCU splat was posted to LKML
at https://lkml.org/lkml/2012/11/7/486. This is at rcu/next. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch allows the STMPE GPIO driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make it possible to disconnect the IB RC connection used by the SRP
protocol to communicate with a target.
Have the SRP transport layer create a sysfs "delete" attribute for
initiator drivers that support this functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Document the sysfs attributes of the SRP initiator (ib_srp) according
to the rules specified in Documentation/ABI/README.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
From Kukjin Kim:
Just adding camif gpio setup and clkdev.
* 'next/cam-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
+ Linux 3.7-rc6
Conflicts due to the 3.7-rc6 sync: arch/arm/mach-highbank/system.c
include/linux/clk-provider.h, resolved as in other branches.
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQtOFbAAoJEAi3KVZQDZAeRbkH/3IWYaAFXi6wnM4yHdYJbp5A
X1375b4Tkjd2Q05gujtNZLDS1gR4O65gJ9nxoV4OuYtqt1WnFUTDU4WozaYFdj8G
1hojkI6qKUddV+EZdMkx1/0YXORsNbGx8PHFPzsLfMHL/qEWjdMgOf4UW+9AogVt
hOwQwIs7SuhDnu0QR0dUH65iU848n5dYSczr/j71l2fqooJ/+KaU1hKKYf/rFvX2
3f9TaDydeglgAUGs7FUL1EbuLQiygIGy1wDhxyVK+g7inAzdQGzVZ7faK8M3NScM
YixWH+uy35ZAS8LlPCpY7DFts4pMtB/5fFvWiMYaBXv53mClgqSaymQDZLObJi8=
=rcOU
-----END PGP SIGNATURE-----
Merge tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper:
mvebu cache-l2x0 for v3.8
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
* tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux:
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
merge conflicts with orion/*
- arch/arm/mach-kirkwood/Kconfig
- select everything
- arch/arm/mach-kirkwood/board-dt.c
- remove AUXDATA
- keep all of_machine_is_compatible()
- use of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsFAhAAoJEAi3KVZQDZAedzgH/3VodO3dDqL4A5HCoUj56HXF
Chkv1cl+1VS3sPnsbbluG0fmDdB619i4Oi2bUWc1YdLpEE0xgyjeAzl5vZDFBjrS
tb8nhWCd2vEcKFSC+HVU2Rhj0NwgUoQifoeD7NSovYZJE6+z+KEY5ny0sE4uaWE1
NL+StBI9dH+SvMi59rnsAxteAnBEAosUoY4KaoHcTHvPsqm9xW5GBh1MkSXQB7fx
kwRrdCaM8U3y3J933/Y4C3maDDQVL7v27YgQp+U5r/eRyN7fVVccxLr6xwl9sck2
fjEpbNRYMImvCOKh8+dhllf/8ZOmjdOore4ORbk4Ulame2KL6pG/2fZ+5N+FrRQ=
=QHBZ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper. Unfortunately this is a combined branch with all
mvebu code as one drop, something we normally try to avoid and instead
slice vendor topics across our branches. Hopefully we can avoid doing
this again for 3.9!
mvebu everything for v3.8
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
* tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux: (85 commits)
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
arm: mvebu: Add support for coherency fabric in mach-mvebu
arm: mvebu: update defconfig to include XOR driver
arm: mvebu: update defconfig to include network driver
...
Signed-off-by: Olof Johansson <olof@lixom.net>
All architectures that use cmd_dtc do so in almost the same way. Create
a central build rule to avoid duplication. The one difference is that
most current uses of dtc build $(obj)/%.dtb from $(src)/dts/%.dts rather
than building the .dtb in the same directory as the .dts file. This
difference will be eliminated arch-by-arch in future patches.
MIPS is the exception here; it already uses the exact same rule as the
new common rule, so the duplicate is removed in this patch to avoid any
conflict. arch/mips changes courtesy of Ralf Baechle.
Update Documentation/kbuild to remove the explicit call to cmd_dtc from
the example, now that the rule exists in a centralized location.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
* pm-cpufreq: (21 commits)
cpufreq: ondemand: update sampling rate only on right CPUs
cpufreq: SPEAr: Add CPUFreq driver
cpufreq: governors: Fix jiffies/cputime mixup (revisited)
cpufreq: ondemand: fix wrong delay sampling rate
cpufreq: exynos: Use static for functions used in only this file
cpufreq: exynos: Broadcast frequency change notifications for all cores
cpufreq: remove use of __devexit
cpufreq: remove use of __devinit
cpufreq: remove use of __devexit_p
cpufreq: Remove unnecessary initialization of a local variable
cpufreq: Make sure target freq is within limits
cpufreq: Avoid calling cpufreq driver's target() routine if target_freq == policy->cur
cpufreq: Fix sparse warning by making local function static
cpufreq: Fix sparse warnings by updating cputime64_t to u64
cpufreq: governors: remove redundant code
cpufreq: return early from __cpufreq_driver_getavg()
cpufreq: fix jiffies/cputime mixup in conservative/ondemand governors
cpufreq: Improve debug prints
cpufreq: Move common part from governors to separate file, v2
cpufreq / core: Fix printing of governor and driver name
...
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
* pm-qos:
PM / QoS: Handle device PM QoS flags while removing constraints
PM / QoS: Resume device before exposing/hiding PM QoS flags
PM / QoS: Document request manipulation requirement for flags
PM / QoS: Fix a free error in the dev_pm_qos_constraints_destroy()
PM / QoS: Fix the return value of dev_pm_qos_update_request()
PM / ACPI: Take device PM QoS flags into account
PM / Domains: Check device PM QoS flags in pm_genpd_poweroff()
PM / QoS: Make it possible to expose PM QoS device flags to user space
PM / QoS: Introduce PM QoS device flags support
PM / QoS: Prepare struct dev_pm_qos_request for more request types
PM / QoS: Introduce request and constraint data types for PM QoS flags
PM / QoS: Prepare device structure for adding more constraint types
Make the description of how tcp_ecn works a bit more explicit and clear.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a term in Documentation/arm64/memory.txt
The modification is based on Catalin Marinas <catalin.marinas@arm.com>'s
suggestion:
"memory" in "ffffffc000000000 ffffffffffffffff 256GB memory"
should be treated as "kernel logical memory map".
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds DMA_ATTR_FORCE_CONTIGUOUS attribute to the DMA-mapping
subsystem.
By default DMA-mapping subsystem is allowed to assemble the buffer
allocated by dma_alloc_attrs() function from individual pages if it can
be mapped as contiguous chunk into device dma address space. By
specifing this attribute the allocated buffer is forced to be contiguous
also in physical memory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Exynos DP changes for the 3.8 merge window.
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
* 'exynos-dp-next' of git://github.com/jingoo/linux:
video: exynos_dp: remove redundant parameters
video: exynos_dp: Fix incorrect setting for INT_CTL
video: exynos_dp: Reset and initialize DP before requesting irq
video: exynos_dp: Enable hotplug interrupts
video: exynos_dp: Move hotplug into a workqueue
video: exynos_dp: Remove sink control to D0
video: exynos_dp: Fix bug when checking dp->irq
video: exynos_dp: Improve EDID error handling
video: exynos_dp: Get pll lock before pattern set
video: exynos_dp: Clean up SW link training
video: exynos_dp: Check DPCD return codes
video: exynos_dp: device tree documentation
video: exynos_dp: Add device tree support to DP driver
Add documentation for the DT bindings in exynos display port driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Handle the jack detection inforamtion as bool from devicetree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add documentation of new sysfs files and new pci_driver SRIOV
configuration interface.
[bhelgaas: changelog]
Signed-off: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)
On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2
On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for EHRWPM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.
So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.
As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
I didn't bother with documenting the really trivial new "extract
something from dpcd" helpers, but the i2c over aux ch is now
documented a bit.
v2: Clarify the comment for i2c_dp_aux_add_bus a bit.
v3: Fix more spelling fail spotted by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again only minimal changes to make kerneldoc no longer shout. Plus a
little introduction in the form of a inline DOC: section to quickly
explain what this is all about.
v2: Fixup spelling fail.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Add the missing doc for drm_helper_move_panel_connectors_to_head.
- Fixup any outdated stuff in existing sections. I've only looked at
those kerneldoc headers that actually resulted in a complaint from
the kerneldoc parser tool.
v2:
- Actually include the docbook snippet in the right patch.
- Fix spelling fail.
v3: It's now called drm_crtc_helper_set_mode, spotted by Laurent
Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I'm devoting all my wrath to that fight, so don't misname it ;-)
v2: Make it clear that this section talks about kms helpers.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
Document how kref_get_unless_zero should be used and how it helps
solve a typical kref / locking problem.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Non-void functions should describe their return values in their kernel-doc
comments. Currently, some don't, others do in various forms. For example:
* Return the result.
* Return: The result.
* Returns the result.
* Returns: the result.
* Return Value: The result.
* @return: the result.
* This function returns the result.
* It will return the result.
Defining a convention would improve consistency of kernel-doc comments. It
would also help scripts/kernel-doc identify the text describing the return
value of a function. Thus allowing additional checks on the comments, and
suitable highlighting in the generated docs (man pages, html, etc).
So, as a convention, use a section named "Return" to describe the return
value of a function.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Aurora is a L2 Cache Controller designed to be compatible with the
L2x0 Cache Controller. L2X0 OF bindings are extended to support some
specificity of Aurora (no cache id part number available through
hardware, always write through mode, choice between outer cache and
system cache).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-and-reviewed-by: Lior Amsalem <alior@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support IOP RR4520/RR4522 which are based on Marvell frey.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a update of Chinese
documentation:Documentation/zh_CN/arm64/memory.txt
It is based on the modifications of Documentation/arm64/memory.txt in
submission :"e3978cde".
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the stmmac.txt adding some information
about the new rx/tx mitigation schema adopted in the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nodelaylog mount option is removed by commit 93b8a585. But there still be
the description about it in the xfs document. This patch removes it.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQp9xhAAoJEEEQszewGV1zBmIQAJbGZ1VaD1+G2cpDTkhvN6wv
08hCpqhPpBLR4Zuy5ld1ZpOPfVaPonO2RT6/isTxlT1qgNhOQEJbaj0cGwnaQ5b/
vqvjkkgiOkVkfKTQMb0IwvCNkGB4o1RWiBmvZ+VrPcWfmAkXoCQ4uQuT/I+msjeJ
dApJNJP8dwuCJTlX+JsUEDGK5Rtk1UrRMn/ZeQ8JNn7WcztkTd7l5I8oqTrmjtcE
08DfvuByL2InwN1Drs5quaW4NaWg6ZSmMGMDJaH2ETXbZALR1/AXdhBkMSkWm3ty
68O52eIqqJYT+pL3W4MOww7fG9602kK6pqDnYs4yIHQ7pWEns2m4jqAryuTRGYxv
hech+i/37b5ghgwuLSsMNNVO+c7gSIT4lHY1bStRGdJMrlRVSPDwn1wJhXs3PeC7
D+TQIngHUfwSN0kjme57MwmKx3epjF5M5A3JjcWGKewbnjj28K7TuGs0voHxh/5L
FVf9YC/k07mQoGlaLAm4aa5RGCH0YjoD/7Hllaopa/yxajVx1YtwklV4kZZ9QFPl
N2F74bDyQjr9j+lK7oa6Z3YjywZX2L19cfYEhoXQ/qvYx/n4Qg5qCVAcq+siCOt5
6TPmo3zP9Wa6f6aLmiFqVQEHd+Xc1KFFGBLzOJ3NQRqZreDdB9cHTF/VKB3xYBzT
MT1tLweT+uqMZElSIsS+
=zpgo
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>:
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
* tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
ARM: integrator: hook the CP into the SoC bus
ARM: integrator: hook the AP into the SoC bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our server rejects compounds containing more than one write operation.
It's unclear whether this is really permitted by the spec; with 4.0,
it's possibly OK, with 4.1 (which has clearer limits on compound
parameters), it's probably not OK. No client that we're aware of has
ever done this, but in theory it could be useful.
The source of the limitation: we need an array of iovecs to pass to the
write operation. In the worst case that array of iovecs could have
hundreds of elements (the maximum rwsize divided by the page size), so
it's too big to put on the stack, or in each compound op. So we instead
keep a single such array in the compound argument.
We fill in that array at the time we decode the xdr operation.
But we decode every op in the compound before executing any of them. So
once we've used that array we can't decode another write.
If we instead delay filling in that array till the time we actually
perform the write, we can reuse it.
Another option might be to switch to decoding compound ops one at a
time. I considered doing that, but it has a number of other side
effects, and I'd rather fix just this one problem for now.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
stime and utime are declared __u64 but are never used. On a glibc system
this is harmless lint, but on a uClibc system, because of the difference
in they way header files stack, including stdio.h brings in time.h and
this causes a name collision with stime. Since these are useless anyhow,
we remove them.
Signed-off-by: Anthony G. Basile <basile@opensource.dyc.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
SPEAr3xx architecture includes shared/multiplexed irqs for certain set
of devices. The multiplexor provides a single interrupt to parent
interrupt controller (VIC) on behalf of a group of devices.
There can be multiple groups available on SPEAr3xx variants but not
exceeding 4. The number of devices in a group can differ, further they
may share same set of status/mask registers spanning across different
bit masks. Also in some cases the group may not have enable or other
registers. This makes software little complex.
Present implementation was non-DT and had few complex data structures to
decipher banks, number of irqs supported, mask and registers involved.
This patch simplifies the overall design and convert it in to DT. It
also removes all registration from individual SoC files and bring them
in to common shirq.c.
Also updated the corresponding documentation for DT binding of shirq.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrc/qAAoJEAi3KVZQDZAeGIcIAJ70hcz/cKdEKNpekMRoMWpz
LoDXtPqRuUvCqBdUNFkJyPAhHHkWwnU6KRcBRz1dknTtJ7nyCkDQYRG/JIroIs8I
X9N6JbPH7FMU+Z1ZUAM2ww+pEAIQkwX06erAy9u/a7ivMj/0LeXboNK+ngIx1jgL
xz2SS4wJrujPwvT2rYo4nJ+WwGiiIPbRjiY7r87rD/DQ9nY9DxKgfve7pRhaCCZS
Baw48u8qTe6M9LGcXw+b/MSHGCTB6YabqaRHMAr/1NK0Z3JDGU8tEpOuMCnFX7SA
6CxEymw5/8fzyTgdRz7FRd9Hg28y5Cd+T2l48X4tSL/M16H4EeBOxj6ub4zCi9s=
=nsDw
-----END PGP SIGNATURE-----
Merge tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/boards
From Jason Cooper:
orion boards for v3.8
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
* tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
From Kukjin Kim:
Here is second Samsung DT stuff for v3.8.
This is including power domain DT support for exynos and Google ARM
Chromebook, Snow board and exynos4210-origen updates.
* 'next/dt-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Use drive strength 3 for SD pins for exynos4
ARM: dts: Set up power domains for exynos4
ARM: EXYNOS: Bind devices to power domains using DT
ARM: EXYNOS: Fix power domain name initialization
ARM: EXYNOS: Detect power domain state on registration from DT
ARM: dts: Add vmmc fixed voltage regulator for exynos4210-origen
ARM: dts: Update sdhci nodes for current bindings for exynos4210-origen
ARM: dts: Update for pinctrl-samsung driver for exynos4210-origen
ARM: dts: Split memory sections for exynos4210-origen
ARM: EXYNOS: add all i2c busses to auxdata for DT
ARM: dts: Add aliases for i2c controller for exynos4
ARM: dts: Add board dts file for Snow board (ARM Chromebook)
ARM: dts: Move the dwmmc aliases from smdk5250 dts to exynos
Add/add conflicts resolved in arch/arm/boot/dts/exynos5250-smdk5250.dts
and arch/arm/mach-exynos/mach-exynos5-dt.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IZiZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for v3.8
* tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge my own merge branch to get various fixes from there
and upstream, especially the hvc console tty refcouting fixes
which which testing is quite a bit harder...
This patch adds description and usage examples for exporting
DMABUF file descriptor in V4L2.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds description and usage examples for importing
DMABUF file descriptor in V4L2.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch allows the STMPE driver to be successfully probed and
initialised when Device Tree support is enabled. Besides the usual
platform data changes, we also separate the process of filling in
the 'in use' pin bitmap, as we have to extract the information from
Device Tree in the DT boot case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Given appropriate devicetree bindings, this driver registers a
pm_power_off function to set a GPIO line high/low to power down
your board.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by:Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on previous work by Michael Walle and Jason Cooper.
Made their work actually work, which required added interrupt from DT
and auxdata, along with setting the dma_mask, which DT does not
currently do.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some commands don't work in its example doc. The patch will fix it.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pulling in a newer version of the depend branch from the gpio tree,
since there was some randconfig breakage introduced at the version we
had, and we want to keep those things as bisectable as possible. It's
not bad enough to warrant a rebase though, so there'll be a window of
exposure to this.
* depends/gpio-devel:
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
Signed-off-by: Olof Johansson <olof@lixom.net>
This device doesn't have a pdata definition for legacy boards, and
unless anyone need to control the reset GPIO, it's not worth adding one.
So this feature is only available to DT users for now.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously a generic binding 'i2c-client-wake' was created which
enabled I2C devices to register themselves as wake-up devices.
This binding was later over-thrown by 'wakeup-source'. The STMPE
driver was fixed-up, but the document was neglected. This patch
aims to rectify that.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for encoding PWM properties in bit encoded form with
of_pwm_xlate_with_flags() function support. Platforms require platform
specific PWM properties has to populate in 3rd cell of the pwm-specifier
and PWM driver should also set .of_xlate support with this function.
Currently PWM property polarity encoded in bit position 0 of the third
cell in pwm-specifier.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for PWM chips present on SPEAr platforms. These PWM
chips support 4 channel output with programmable duty cycle and
frequency.
More details on these PWM chips can be obtained from relevant
chapter of reference manual, present at following[1] location.
1. http://www.st.com/internet/mcu/product/251211.jsp
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Inherit netprio configuration from ->css_online(), allow nesting and
remove .broken_hierarchy marking. This makes netprio_cgroup's
behavior match netcls_cgroup's.
Note that this patch changes userland-visible behavior. Nesting is
allowed and the first level cgroups below the root cgroup behave
differently - they inherit priorities from the root cgroup on creation
instead of starting with 0. This is unfortunate but not doing so is
much crazier.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
In current code the ethernet PLL is not handled correctly. The PLL runs at 500MHz
and has different outputs. Only the enet reference clock is implemented. This
patch changes the PLL so that it outputs 500MHz and adds the additional outputs
as dividers. This now matches the datasheet which says:
> This PLL synthesizes a low jitter clock from 24 MHz reference clock.
> The PLL outputs a 500 MHz clock. The reference clocks generated by this PLL are:
> • Ref_PCIe = 125 MHz
> • Ref_SATA = 100 MHz
> • Ref_ethernet, which is configurable based on the PLL_ENET[1:0] register field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In recent reference manuals the PLLs were renumbered. PLL8 now is
PLL6 and vice versa. Change the code according to the reference
manual to avoid confusion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to use gpio for chip select with no modification in the
driver binding
When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
DMA_ERROR_CODE is not defined on all architectures and is architecture
specific. Instead, use the constant, ~0 to indicate unmapped regions.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dabusb was removed with commit dae86ccbc3 ("[media] dabusb: remove
obsolete driver"), so remove the last vestiges of firmware and
documentation.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Rob Landley <rob@landley.net>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs/LcACgkQCwYYjhRyO9WrOgCfeWpA9XdQnwexySw5tPXS7Qdp
aJEAn2ql07SECpTRWezTJptHL0oI1dFF
=b0T7
-----END PGP SIGNATURE-----
Merge tag 'marvell-hwiocc-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Add hardware I/O coherency support for Armada 370/XP
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
From Michal Simek:
This branch depends on arm-soc devel/debug_ll_init branch because
we needed Rob's "ARM: implement debug_ll_io_init()"
(sha1: afaee03511ba8002b26a9c6b1fe7d6baf33eac86)
patch.
This branch also depends on zynq/dt branch because of previous major
zynq changes.
zynq/cleanup branch is subset of zynq/dt.
* 'zynq/multiplatform' of git://git.monstr.eu/linux-2.6-microblaze:
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Add/add conflict in arch/arm/Kconfig.debug.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: EXYNOS: DT Support for SATA and SATA PHY
ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
ARM: dts: Add node for touchscreen for exynos4210-trats
ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
ARM: dts: Add node for i2c3 bus for exynos4210-trats
ARM: dts: Add nodes for GPIO keys available on Trats
ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
ARM: dts: Add nodes for pin controllers for exynos4x12
pinctrl: samsung: Add support for EXYNOS4X12
gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
ARM: dts: add board dts file for EXYNOS4412 based SMDK board
ARM: dts: Add support for EXYNOS4X12 SoCs
ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
ARM: EXYNOS: Add MFC device tree support
ARM: dts: Enable serial controllers on Origen and SMDKV310
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
...
Add/add conflicts in:
arch/arm/boot/dts/exynos5250-smdk5250.dts
arch/arm/boot/dts/exynos5250.dtsi
arch/arm/mach-exynos/mach-exynos5-dt.c
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Here is a pull request to add the support for Allwinner A10 SoCs.
* sunxi/soc2:
ARM: sunxi: Add sunxi restart function via onchip watchdog
ARM: sunxi: Add sun4i and cubieboard support
ARM: sunxi: Add earlyprintk support for UART0 (sun4i)
ARM: sunxi: Restructure sunxi dts/dtsi files
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
This includes supporting legacy i2c controller and ARM down clock
support for exynos5 and small changes.
[olof: It contains a dependency on samsung/hdmi for HDMI DT bindings, for some reason.]
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* samsung/pinctrl:
pinctrl: samsung: Update error check for unsigned variables
pinctrl: samsung: Add support for EXYNOS4X12
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
pinctrl: samsung: Use per-bank IRQ domain for wake-up interrupts
pinctrl: samsung: Use one GPIO chip per pin bank
pinctrl: exynos: Use one IRQ domain per pin bank
pinctrl: samsung: Include bank-specific eint offset in bank struct
pinctrl: samsung: Hold pointer to driver data in bank struct
pinctrl: samsung: Match pin banks with their device nodes
ARM: dts: exynos4210-pinctrl: Add nodes for pin banks
pinctrl: samsung: Distinguish between pin group and bank nodes
pinctrl: samsung: Remove static pin enumerations
pinctrl: samsung: Assing pin numbers dynamically
pinctrl: samsung: Do not pass gpio_chip to pin_to_reg_bank
pinctrl: samsung: Detect and handle unsupported configuration types
From Kukjin Kim:
This is for adding support for DT based exynos5250 hdmi and it adds
device node for hdmi, mixer, hdmiphy and hdmiddc.
* 'next/hdmi-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
Armada 370 and XP come with an unit called coherency fabric. This unit
allows to use the Armada 370/XP as a nearly coherent architecture. The
coherency mechanism uses snoop filters to ensure the coherency between
caches, DRAM and devices. This mechanism needs a synchronization
barrier which guarantees that all the memory writes initiated by the
devices have reached their target and do not reside in intermediate
write buffers. That's why the architecture is not totally coherent and
we need to provide our own functions for some DMA operations.
Beside the use of the coherency fabric, the device units will have to
set the attribute flag of the decoding address window to select the
accurate coherency process for the memory transaction. This is done
each device driver programs the DRAM address windows. The value of the
attribute set by the driver is retrieved through the
orion_addr_map_cfg struct filled during the early initialization of
the platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
The documentation doesn't match the actual function prototype. This is a
trivial patch to fix it.
Signed-off-by: Alison Chaiken <alison_chaiken@mentor.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There are several drivers that use LEDs and depend on exactly the same
device tree binding. However, the binding documentation has simply been
cut-and-paste into each of the binding documents. Rather than continue
to duplicate it, this patch adds a common led binding document that all
can reference.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enhances the IRQ controller driver to add support for
Inter-Processor-Interrupts that are needed to enable SMP support.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and Armada XP SOCs have a power management service unit
which is responsible for powering down and waking up CPUs and other
SOC units. This patch adds support for this unit.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and Armada XP SOCs have a coherency fabric unit which
is responsible for ensuring hardware coherency between all CPUs and
between CPUs and I/O masters. This patch provides the basic support
needed for SMP.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This patch adds a way to specify bindings between devices and power
domains using device tree.
A device can be bound to particular power domain by adding a
power-domain property containing a phandle to the domain. The device
will be bound to the domain before binding a driver to it and unbound
after unbinding a driver from it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Initial state of power domains might vary on different boards and with
different bootloaders.
This patch adds detection of initial state of power domains when being
registered from DT.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Set tps65217 PMIC status to OFF if power enable toggle is supported.
By setting this bit to 1 to enter PMIC to OFF state when PWR_EN pin
is pulled low. Also adds a DT flag to specify that device pmic
supports shutdown control or not.
Signed-off-by: Colin Foe-Parker <colin.foeparker@logicpd.com>
[anilkumar@ti.com: move the additions to tps65217 MFD driver]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The async unlink behavior has been working over years. The option was
provided only as a workaround for 2.4.x kernel. Let's get rid of it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From Pawel Moll:
* 'vexpress-clk-soc' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove motherboard dependencies in the DTS files
ARM: vexpress: Start using new Versatile Express infrastructure
ARM: vexpress: Add config bus components and clocks to DTs
mfd: Versatile Express system registers driver
mfd: Versatile Express config infrastructure
From Stephen Warren:
ARM: bcm2835: core SoC enhancements
A machine restart/reboot implementation is added. The GPIO/pinmux
controller is instantiated, and dummy gpio.h added.
* tag 'bcm2835-for-3.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: enable GPIO/pinctrl
ARM: bcm2835: implement machine restart hook
Signed-off-by: Olof Johansson <olof@lixom.net>
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ytxh
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
ARM: tegra: dts: add sflash controller dt entry
ARM: tegra: ventana: Add NCT1008 temperature sensor
ARM: tegra: tamonten: Add NCT1008 temperature sensor
ARM: tegra: harmony: Add ADT7641 temperature sensor
ARM: tegra: tec: Remove redundant DT properties
ARM: tegra: tamonten: Add DDC/PTA pinmux
ARM: tegra: dts: cardhu: enable SLINK4
ARM: tegra: dts: add slink controller dt entry
ARM: dt: tegra: ventana: define pinmux for ddc
ARM: dt: t30 cardhu: set pinmux and power for wlan
ARM: dt: t20 ventana: set pinmux and power for wlan
...
- conversion of watchdog to DT
- usart definition for evk-pro3 board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQqm8pAAoJEAf03oE53VmQpEEH/00dsxSUrL06NzwP8Y1+UjW8
OXJPJUU0Mor/b5zCp3wsxB4+imZ4y4oqJ42qvFZjRLHj0KMvVdnxm5SNIpbQtXxV
jXPqXYk8yfH4YF3DDLuiD9wkXjwtgck7+D7ogcAIb9bbWyyGusKIcs72smvGanCd
zZrWIOGwXlqgrF5CX8kl6SIhdnYvMtee7GlzbiFHlKr4CLPOIR3iahnHR26gkzLH
cRjYVujYaHpQKBR8XvMgIl7brCUTX2KuMajvVOF8EShk8BU2MW1GHFY0cNfqaKRn
R/Z9itXk6P/h3s/Wf+Qyfpuz3E0zbS80uN/NyrIbcGbAQQIesuo8pcd9xZZ5yg0=
=whJu
-----END PGP SIGNATURE-----
Merge tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
More DT material for AT91:
- conversion of watchdog to DT
- usart definition for evk-pro3 board
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: evk-pro3: enable watchdog
ARM: at91/dts: add at91sam9_wdt driver to at91sam926x, at91sam9g45
watchdog: at91sam9_wdt: add device tree support
ARM: at91: dt: evk-pro3: enable uart0 and uart2
Also the driver was modifued to take advantage of recent improvements in
matrix_keypad_build_keymap() implementation, which automatically allocates
memory for keymap.
The driver was tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCmwSAACgkQGxsu9jQV9nbssgCcChzwuFlPkP4sVdTtAGGh5mWD
rNcAn3PfG1ByMR57GkDtdQiAjS5N2dME
=Pi49
-----END PGP SIGNATURE-----
Merge tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner SoC support for 3.8
* tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux:
ARM: sunxi: Add entry to MAINTAINERS
ARM: sunxi: Add device tree for the A13 and the Olinuxino board
ARM: sunxi: Add earlyprintk support
ARM: sunxi: Add basic support for Allwinner A1x SoCs
irqchip: sunxi: Add irq controller driver
clocksource: sunxi: Add Allwinner A1X Timer Driver
clk: sunxi: Add dummy fixed rate clock for Allwinner A1X SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
Their stock ticker is 3407.T which wouldn't make a good DT vendor
prefix. Use the company name initials instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch adds a device tree vendor prefix for Synopsys Inc.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Now that the Armada 370/XP platform has gained proper integration with
the clock framework, we add clk support in the Marvell Armada 370/XP
Ethernet driver.
Since the existing Device Tree binding that exposes a
'clock-frequency' property has never been exposed in any stable kernel
release, we take the freedom of removing this property to replace it
with the standard 'clocks' clock pointer property.
The Device Tree binding documentation is updated accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds support for a new IIO channel type for pressure measurements.
This can for example be used for barometric pressure sensors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch finally adds a Device Tree binding to the mv_xor
driver. Thanks to the previous cleanup patches, the Device Tree
binding is relatively simply: one DT node per XOR engine, with
sub-nodes for each XOR channel of the XOR engine. The binding
obviously comes with the necessary documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
This driver allows to provide DT clocks for clock gates found on
Marvell Dove and Kirkwood SoCs. The clock gates are referenced by
the phandle index of the corresponding bit in the clock gating control
register to ease lookup in the datasheet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add Armada 370/XP specific CPU clocks
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds Device Nodes for SATA and SATA PHY device.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
[kgene.kim@samsung.com: removed address definitions as per comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that governor list can be variable, knowing the available governors
is useful to be able to select a governor using relevant sysfs node.
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This allows us to select governor runtime from the
default configuration without having to rebuild kernel
or the devfreq driver using the sysfs node:
/sys/class/devfreq/.../governor
cat of the governor will return valid governor
and an echo 'governor_name'>governor will switch
governor
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds sysfs node which can be used to get information of frequency
transition. It represents transition table which contains total number of transition of
each freqeuncy state and time spent. It is inspired CPUFREQ's status driver.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
[Added Documentation/ABI entry, updated kernel-doc, and resolved merge conflict]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
devfreq governors such as ondemand are controlled by a min and
max frequency, while governors like userspace governor allow us
to set a specific frequency.
However, for the same specific device, depending on the SoC, the
available frequencies can vary.
So expose the available frequencies as a snapshot over sysfs to
allow informed decisions.
This was inspired by cpufreq framework's equivalent for similar
usage sysfs node: scaling_available_frequencies.
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.
v2 patch mods
--------
- Remove l2x0_of_init call as there were problems with the code.
A separate patch will be submitted with cache init code
- Rename capri files and refs to bcm281xx-based names
- Add bcm281xx binding doc
- various misc cleanups
v3 patch mods
-------------
- Remove extra #include lines
- Remove remaining references to capri
- dt uart chipset string added
- cleaned up chip # references
v4 patch mods
-------------
- swap order of compatible definitions for uart
- fix typo
v5 patch mods
-------------
- Rename bcm281xx to bcm11351 in dts+code,
leaving references to bcm281xx only in help+comments.
v6 patch mods
-------------
- fix typo in uart 'compatible' string
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/FbB
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
These changes add DT boot support to DaVinci DA850
SoC.
* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: generate dtbs for da850 boards
ARM: davinci: add support for am1808 based EnBW CMC board
ARM: davinci: da850 evm: add DT data
ARM: davinci: da850: add SoC DT data
ARM: davinci: da850: add DT boot support
ARM: davinci: da8xx: add DA850 PRUSS support
ARM: davinci: add platform hook to fetch the SRAM pool
ARM: davinci: da850: changed SRAM allocator to shared ram.
ARM: davinci: sram: switch from iotable to ioremapped regions
uio: uio_pruss: replace private SRAM API with genalloc
ARM: davinci: serial: provide API to initialze UART clocks
ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>
A helper that drivers can use to send vblank event after a pageflip.
If the driver doesn't support proper vblank irq based time/seqn then
just pass -1 for the pipe # to get do_gettimestamp() behavior (since
there are a lot of drivers that don't use drm_vblank_count_and_time())
Also an internal send_vblank_event() helper for the various other code
paths within drm_irq that also need to send vblank events.
v1: original
v2: add back 'vblwait->reply.sequence = seq' which should not have
been deleted
v3: add WARN_ON() in case lock is not held and comments
v4: use WARN_ON_SMP() instead to fix issue with !SMP && !DEBUG_SPINLOCK
as pointed out by Marcin Slusarz
v5: update docbook
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CGRP_CPUSET_CLONE_CHILDREN triggers ->post_clone(). Now
that clone_children is cpuset specific, there's no reason to have this
rather odd option activation mechanism in cgroup core. cpuset can
check the flag from its ->css_allocate() and take the necessary
action.
Move cpuset_post_clone() logic to the end of cpuset_css_alloc() and
remove cgroup_subsys->post_clone().
Loosely based on Glauber's "generalize post_clone into post_create"
patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Original-patch-by: Glauber Costa <glommer@parallels.com>
Original-patch: <1351686554-22592-2-git-send-email-glommer@parallels.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Glauber Costa <glommer@parallels.com>
clone_children is only meaningful for cpuset and will stay that way.
Rename the flag to reflect that and update documentation. Also, drop
clone_children() wrapper in cgroup.c. The thin wrapper is used only a
few times and one of them will go away soon.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Glauber Costa <glommer@parallels.com>
Rename cgroup_subsys css lifetime related callbacks to better describe
what their roles are. Also, update documentation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
When booting through a device tree, the kernel cpu logical id map can be
initialized using device tree data passed by FW or through an embedded blob.
This patch adds a function that parses device tree "cpu" nodes and
retrieves the corresponding CPUs hardware identifiers (MPIDR).
It sets the possible cpus and the cpu logical map values according to
the number of CPUs defined in the device tree and respective properties.
The device tree HW identifiers are considered valid if all CPU nodes contain
a "reg" property, there are no duplicate "reg" entries and the DT defines a
CPU node whose "reg" property matches the MPIDR[23:0] of the boot CPU.
The primary CPU is assigned cpu logical number 0 to keep the current convention
valid.
Current bindings documentation is included in the patch:
Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Commit 77d1a49995 ("x86, boot: make
symbols from the main vmlinux available") removed all traces of
offsets.h from the tree. Remove its entries in dontdiff and x86/boot's
.gitignore file too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.
The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds device tree support for charging algorithm driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for ab8500-charger driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for battery-temperature-monitor driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
- This patch adds device tree support for fuelgauge driver
- optimize bm devices platform_data usage and of_probe(...)
Note: of_probe() routine for battery managed devices is made
common across all bm drivers.
- test status:
- interrupt numbers assigned differs between legacy and FDT mode.
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch extends the driver with any necessary SoC-specific
definitions to support EXYNOS4X12 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Based on AT91 PIT DT patch from Jean-Christophe PLAGNIOL-VILLARD.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add support for power supply attributes CHARGE_CONTROL_LIMIT
and CHARGE_CONTROL_LIMIT_MAX.
These new attributes will enable the user space to implement
custom charging algorithms based on platform state.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
SPEAr platform provides a provision to control chipselects of ARM PL022
Prime Cell spi controller through its system registers, which otherwise
remains under PL022 control which some protocols do not want.
This commit intends to provide the spi chipselect control in software over
gpiolib interface. spi chip drivers can use the exported gpiolib interface to
define their chipselect through DT or platform data.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches)
revert "mm: fix-up zone present pages"
tmpfs: change final i_blocks BUG to WARNING
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
rapidio: fix kernel-doc warnings
swapfile: fix name leak in swapoff
memcg: fix hotplugged memory zone oops
mips, arc: fix build failure
memcg: oom: fix totalpages calculation for memory.swappiness==0
mm: fix build warning for uninitialized value
mm: add anon_vma_lock to validate_mm()
oom_badness() takes a totalpages argument which says how many pages are
available and it uses it as a base for the score calculation. The value
is calculated by mem_cgroup_get_limit which considers both limit and
total_swap_pages (resp. memsw portion of it).
This is usually correct but since fe35004fbf ("mm: avoid swapping out
with swappiness==0") we do not swap when swappiness is 0 which means
that we cannot really use up all the totalpages pages. This in turn
confuses oom score calculation if the memcg limit is much smaller than
the available swap because the used memory (capped by the limit) is
negligible comparing to totalpages so the resulting score is too small
if adj!=0 (typically task with CAP_SYS_ADMIN or non zero oom_score_adj).
A wrong process might be selected as result.
The problem can be worked around by checking mem_cgroup_swappiness==0
and not considering swap at all in such a case.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue
lock, from Arik Nemtsov.
2) Don't call 802.11 driver's filter configure method until it's
actually open, from Felix Fietkau.
3) Use ieee80211_free_txskb otherwise we leak control information.
From Johannes Berg.
4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg.
5) The shift mask trick doesn't work properly when 'optname' is out of
range in do_ip_setsockopt(). Use a straightforward switch statement
instead, the compiler emits essentially the same code but without
the missing range check. From Xi Wang.
6) Fix when we call tcp_replace_ts_recent() otherwise we can
erroneously accept a too-high tsval. From Eric Dumazet.
7) VXLAN bug fixes, mostly to do with VLAN header length handling, from
Alexander Duyck.
8) Missing return value initialization for IPV6_MINHOPCOUNT socket
option handling. From Hannes Frederic.
9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers,
from Xiaotian Feng.
10) At smsc911x driver init time, we don't know if the chip is in word
swap mode or not. However we do need to wait for the control
register's ready bit to be set before we program any other part of
the chip. Adjust the wait loop to account for this. From Kamlakant
Patel.
11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c
12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala.
13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi.
14) TCP metrics hash table kzalloc() based allocation can fail, back
down to using vmalloc() if it does. From Eric Dumazet.
15) Fix packet steering out-of-order delivery regression, from Tom
Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net-rps: Fix brokeness causing OOO packets
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
batman-adv: process broadcast packets in BLA earlier
batman-adv: don't add TEMP clients belonging to other backbone nodes
batman-adv: correctly pass the client flag on tt_response
batman-adv: fix tt_global_entries flags update
tilegx: request_irq with a non-null device name
net: correct check in dev_addr_del()
tcp: fix retransmission in repair mode
sctp: fix /proc/net/sctp/ memory leak
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
drivers/net: fix tasklet misuse issue
ipv4/ip_vti.c: VTI fix post-decryption forwarding
brcmfmac: fix typo in CONFIG_BRCMISCAN
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
vxlan: fix a typo.
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
doc/net: Fix typo in netdev-features.txt
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
...
This hooks the Integrator/CP into the SoC bus when booting from
device tree, by mapping the CP controller registers first,
then registering the SoC device, and then populating the device
tree with the SoC device as parent.
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Tegra RTC maintains seconds and milliseconds counters, and five alarm
registers. The alarms and other interrupts may wake the system from
low-power state.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra timer provides a number of 29-bit timer channels, a single
32-bit free running counter, and in the Tegra30 variant, 5 watchdog modules.
The first two channels may also trigger a legacy watchdog reset.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is mostly a revert of 01dc52ebdf ("oom: remove deprecated oom_adj")
from Davidlohr Bueso.
It reintroduces /proc/pid/oom_adj for backwards compatibility with earlier
kernels. It simply scales the value linearly when /proc/pid/oom_score_adj
is written.
The major difference is that its scheduled removal is no longer included
in Documentation/feature-removal-schedule.txt. We do warn users with a
single printk, though, to suggest the more powerful and supported
/proc/pid/oom_score_adj interface.
Reported-by: Artem S. Tashkinov <t.artem@lycos.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RCU callback execution can add significant OS jitter and also can
degrade both scheduling latency and, in asymmetric multiprocessors,
energy efficiency. This commit therefore adds the ability for selected
CPUs ("rcu_nocbs=" boot parameter) to have their callbacks offloaded
to kthreads. If the "rcu_nocb_poll" boot parameter is also specified,
these kthreads will do polling, removing the need for the offloaded
CPUs to do wakeups. At least one CPU must be doing normal callback
processing: currently CPU 0 cannot be selected as a no-CBs CPU.
In addition, attempts to offline the last normal-CBs CPU will fail.
This feature was inspired by Jim Houston's and Joe Korty's JRCU, and
this commit includes fixes to problems located by Fengguang Wu's
kbuild test robot.
[ paulmck: Added gfp.h include file as suggested by Fengguang Wu. ]
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
urgent.2012.10.27a: Fix for RCU user-mode transition (already in -tip).
doc.2012.11.08a: Documentation updates, most notably codifying the
memory-barrier guarantees inherent to grace periods.
fixes.2012.11.13a: Miscellaneous fixes.
srcu.2012.10.27a: Allow statically allocated and initialized srcu_struct
structures (courtesy of Lai Jiangshan).
stall.2012.11.13a: Add more diagnostic information to RCU CPU stall
warnings, also decrease from 60 seconds to 21 seconds.
hotplug.2012.11.08a: Minor updates to CPU hotplug handling.
tracing.2012.11.08a: Improved debugfs tracing, courtesy of Michael Wang.
idle.2012.10.24a: Updates to RCU idle/adaptive-idle handling, including
a boot parameter that maps normal grace periods to expedited.
Resolved conflict in kernel/rcutree.c due to side-by-side change.
This commit adds the documentation of the rcuexp debugfs trace file
that records statistics for expedited grace periods.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit updates the tracing documentation to reflect the new
format that has per-RCU-flavor directories.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Use a better name for the USB PHY clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The registers in the GRLIB port of the controller are 32-bit and in big endian
byte order. The PRELOW and PREHIGH registers are merged into one register. The
subsequent registers have their offset decreased accordingly. Hence the register
access needs to be handled in a non-standard manner using custom getreg and
setreg functions.
Add setreg and getreg functions for different register widths and let oc_setreg
and oc_getreg use function pointers to call the appropriate functions.
A type is added as the data of the of match table entries. A new entry with a
different compatible string is added to the table. The type of that entry
triggers usage of the custom grlib functions by setting the setreg and getreg
function pointers.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There are also a few imx6 improvement patches in there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQpeRkAAoJEFBXWFqHsHzOHMoH/3pxLWMHlaFFN70gm33GIEpj
6/P0afKhjEseQDfbvLPfRPwHTQIkw/xQ2rfSrZGUnhgAGN2SfOcxiREFpdChgqyb
b5kO+3oQpnQTFce6tuqCI8j4LAqr63AHhJPWZuDEBaR52Vs0i9gYr2Zwv7i+iUh7
fuLu+NDQLKOkEW7W97FRFVWKRGmSMhJYvhNn+kgleFUhvzUKpJ6n7kFsT05BSl97
EiJHtVxOv+RtlFvx7jrTr18NM2i4Kb4IzEfLzgYOowK9cwfNuhnaxsQvAUiGSa+z
EuvXdKN2btW0PtqHVBPdz5T0OzTyJheaCETKTqz0XM32/SVz5Ma3gZEEDagGLiw=
=zBAI
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch. Most of them are dts changes.
There are also a few imx6 improvement patches in there.
* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: select ARM and PL310 errata
ARM: imx6q: print silicon version on boot
ARM i.MX dts: Consistently add labels to devicenodes
ARM: dts: imx6q-sabresd: add volume up/down gpio keys
ARM: dts: imx53: pinctl update
ARM: imx: enable cpufreq for imx6q
ARM: dts: imx6q: enable snvs lp rtc
ARM: dts: imx6q-sabreauto: Add basic support
ARM: imx6q: let users input debug uart port number
ARM: dts: imx53-qsb: Make DA9053 regulator functional
ARM: dts: imx53-qsb: Use pinctrl for gpio-led
ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>
From Michal Simek <michal.simek@xilinx.com>:
These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABCAAGBQJQpmDiAAoJEPFlmONMx+ezSJMP/Az4J4R6ZEh8J8xt/Uf4bw78
k6jMg1cBRa/DRJWUWvymjyFH/NvjnbtntV4bOBbey05efB+RCGRl9TW6hGLtL5M6
EfA2Nr7flw/BCdEuf0uI64p0rWmtfzV+SZOsPk6HKAzHo2uV/hQWYUUmvzNrVqVz
8XVEfTQWgipA8SOPKfdvCezoO7PWHD6l9fy/mJkMyyf4Py1WDXXt+gCHUGZlFKAq
8ZXE3B+ftwDUOwlrLl7mcJJtRjabUHQpDS/hmkhjVzTrrMQb+V2/BIzODkT35B6m
bHc5zRlYVXVgE/XqxcD79zzl+ixvyfdYThLQ8GzoxyhUmKNOEjub+8udzX2YEB+b
VLS06QmhhJn8xj6EIVM5WZIK4bR2OZoT2hCpuO2nJUyhbVSksO1GF1T8v8H3IHQf
THw3WSh7bFIFrgJhj//UbLXkTaQ4/bkqAP064EyuABMvKoaybPOmFe0boN/QoFDz
yC2/b1xTTiG/6nLupz7gLJabdV6iOF9f2rqta65hz+//Qk+Iyeh7iuWfrBspDJCb
3vKBcB75IgRWaaPxJxRFWzP9CN2ouv5q763xSjqldFt9pOF4zvfBfpERkzYn3rwG
/93X1tazBLo+mM7D5QVTrPgfXQs/B3GxIA6tsIIrPqxMpM5u/ONNNCYwINvFI/Xo
aklrgV6n88q3C/Zewebz
=CFfP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for 3.8
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
Add device tree file for the armadeus apf27
ARM i.MX: Add Ka-Ro TX25 devicetree
ARM i.MX25: Add devicetree
ARM i.MX25: Add devicetree support
ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
based on imx-multiplatform branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=P3UZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX SoC updates
based on imx-multiplatform branch.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX51 babbage: Add display support
ARM i.MX6: Add IPU support
ARM i.MX51: Add IPU support
ARM i.MX53: Add IPU support
ARM i.MX5: switch IPU clk support to devicetree bindings
ARM i.MX6: fix ldb_di_sel mux
ARM i.MX51: setup MIPI during startup
mx2_camera: Fix regression caused by clock conversion
ARM: clk-imx27: Add missing clock for mx2-camera
ARM i.MX27: Fix low reference clock path
ARM: dts: imx27-3ds: Remove local watchdog inclusion
watchdog: Support imx watchdog on SOC_IMX53
ARM: mach-imx: Support for DryIce RTC in i.MX53
ARM : i.MX27 : split code for allocation of ressources of camera and eMMA
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
