IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d664291db3324d0fcf0985ab5626aac2
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.
This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.
Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix some minor problems in comments of lis331dlh driver
* correct comments with respect to 2G sensitivity
* correct typo lis3331dlh mistake to lis331dlh
* add comment to say only 2G range is supported
* change the function name from lis3lv02d_read_16 to
lis331dlh_read_data.
* update i2c_device_id table entry to maintaine consistancy
* update sensor display message
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_disable_device(pdev) used to be in pci remove function. But this
PCI device has two functions with interrupt lines connected to a
single pin. The other one is a USB host controller. So when we disable
the PIN there e.g. by rmmod hpilo, the controller stops working. It is
because the interrupt link is disabled in ACPI since it is not
refcounted yet. See acpi_pci_link_free_irq called from
acpi_pci_irq_disable.
It is not the best solution whatsoever, but as a workaround until the
ACPI irq link refcounting is sorted out this should fix the reported
errors.
References: https://lkml.org/lkml/2008/11/4/535
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Nobin Mathew <nobin.mathew@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_tty_get() can return NULL after port hangup that may happen anytime.
The patch adds checks that tty_port_tty_get() returns nonNULL around places
where tty is actually used.
I have no actual hardware to test the patch, so I have updated rx side
processing from common sense only.
v2: rx handling updated according Alan Cox feedback.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes some translation error in Documentation/zh_CN/gpio.txt
The modification is based on Dong Aisheng <b29396@freescale.com>'s
corrections:
1.Two "OUTPUT" is incorrectly translated as "输入";
2.five improvement of translation;
3.Delete a redundant paragraph,
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove 3 byte redundant code at the head of
the Documentation/zh_CN/arm/booting
When I see the file Documentation/zh_CN/arm/booting using
Bless(binary Viewer),I find 3 byte redundant in it. So I
make a patch to correcting that error made by me.
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a Chinese translated version of Documentation/video4linux/omap3isp.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some post-3.4 kernels have a problem when a cloned skb is used in the
RX path. This patch handles one such case for r8712u.
The patch was suggested by Eric Dumazet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d97b46a64 ("syscalls, x86: add __NR_kcmp syscall" ) added a new
syscall to support checkpoint restore. It is currently x86-only, but
that restriction will be removed in a subsequent patch. Unfortunately,
the kernel checksyscalls script had a bug which suppressed any warning
to other architectures that the kcmp syscall was not implemented. A
patch to checksyscalls is being tested in linux-next and other
architectures are seeing warnings about kcmp being unimplemented.
This patch adds __NR_kcmp to <asm-generic/unistd.h> so that kcmp is
wired in for architectures using the generic syscall list.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The ELSE IF statements do not work as expected if another ELSE statement
follows. This is because the $if_set is not set. If the ELSE IF
condition is true, the following ELSE should be ignored. But because the
$if_set is not set, the following ELSE will also be executed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
To apply a filter to all the evsels in an evlist.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-v9x3q9rv4caxtox7wtjpchq5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
ERRnoresource is an ERRSRV level (aka server-side) error and means "No
resources currently available for request". Currently that maps to POSIX
-ENOBUFS. No NT errors map to it currently.
NT_STATUS_INSUFFICIENT_RESOURCES and NT_STATUS_INSUFF_SERVER_RESOURCES
are also similar in meaning. Currently the client maps those to
ERRnomem, which maps to -ENOMEM in POSIX.
All of these mappings seem to be quite wrong to me and are confusing for
users. All of the above errors indicate problems on the server, not the
client. Reporting -ENOMEM or -ENOBUFS implies that the client is running
out of resources.
This patch changes those mappings. The NT_* errors are changed to map to
the SRV level ERRnoresource. That error is in turn changed to return
-EREMOTEIO which is the only POSIX error I could find that conveys that
something went wrong on the server. While we're at it, change the SMB2
equivalent error to return the same.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Suresh Jayaraman <sjayaraman@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
`ni_ai_poll()` currently acquires (and later releases) the comedi
device's spin-lock iff `in_interrupt()` returns 0. However, it is only
called during processing of a `COMEDI_POLL` ioctl so `in_interrupt()`
will always return 0 in this case. Remove this test and acquire/release
the spin-lock unconditionally. This eliminates a sparse warning about
different lock contexts for basic block.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`s626_enc_insn_config()` is the `insn_config()` handler for a counter
subdevice. The `data[0]` value is supposed to be one of the
`INSN_CONFIG_...` constants defined in "comedi.h" indicating the type of
configuration instruction, but this function seems to be using it as a
variable value to preload the counter with. Various values of `data[0]`
are going to cause `check_insn_config_length()` in the comedi core
("comedi_fops.c") to return an error, and this function won't be called
in those cases. Most other values will log a warning to the kernel log.
It's not entirely clear what constant should be checked for in
`data[0]`, so add a "FIXME" comment for now.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`s626_enc_insn_config()` is incorrectly dereferencing `insn->data` which
is a pointer to user memory. It should be dereferencing the separate
`data` parameter that points to a copy of the data in kernel memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because that is what it really does, i.e. it applies the filters that
were parsed from the command line and stashed into the evsels they refer
to.
We'll need the set_filter method name to actually apply a filter to all
the evsels in an evlist, for instance, to ask that a syswide tracer
doesn't trace itself.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-v9x3q9rv4caxtox7wtjpchq5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This if() check was flipped from a test for valid data params
to a test for invalid params.
As pointed out by Dan Carpenter, the orignal test was:
if ((data[1] > data[0]) && (data[0] > 0)) {
the flipped test should be:
if (data[1] <= data[0]) ...
Add the missing '='.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will set up a syscall open tracepoint event, generate an open with
invalid flags, then check those flags were the ones reported in the
tracepoint fired.
For the filename we need vfs:getname, but that will go thru some more
iterations as the vfs getname codebase is going thru changes lately.
When that is in I'll just check that the perf_evsel__newtp constructor
is not bailing out and then add it to the evlist, catch the event and
check the filename against the one used in the 'open' call used to
trigger the event.
Cc: David Ahern <dsahern@gmail.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-p5w9aq0jcbb91ghzqomowm16@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We were relying on the info in pevent, but since we have it in
perf_evsel, set up by the perf_session routine if read from a perf.data
file or by whoever creates the evsels, use it.
New 'perf test' entries will use it to parse locally generated events,
in a non perf.data centered workflow.
As well as use byteswap.h to get per arch optimized swap routines, like
other parts of perf (header, perf_evsel__parse_sample, symbol, etc)
already do.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-8tjuxk09mlsfmh7macgkxsip@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cleanup the comments to follow the coding style of the kernel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private data is kzalloc'ed. There is no need to set any
of the initial data to '0'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This variable is never used in the driver. Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This variable is never used in the driver. Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IsBoardRevA is not defined in the driver. Remove the comment
about it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until it's determined if this workaround can be removed, block
out the code with an #if 0/#endif and remove the individual
comments on each line.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This variable is only used to count the number of dma buffers
allocated during the attach. If an allocation fails, the attach
function exits with -ENOMEM. When this variable is checked later
it will always be == 2. Just remove the variable and the check.
This allows bringing the code back an indent level in
s626_initialize(). Note, coding style issues in this function
are not addressed yet.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a simple dev_info() message after a successfull attach.
Change the final return to '0' to indicate success.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private data is kzalloc'ed. All the variables in it are
initially '0'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make the attach a bit cleaner, factor the board init code
out of attach_pci() into a new function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only set dev->irq if request_irq is successfull.
Remove the kernel message noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make the attach a bit cleaner, factor the dma buffer allocation
out of attach_pci() into a new function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'devpriv->base_addr' is valid from this point on in the attach_pci()
function. Remove the unnecessary checks.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local variable 'resourceStart' is only used in the ioremap()
to hold the PCI bar 0 base address. Just use the pci_resource_start()
directly in the ioremap().
Also, instead of assuming the resource size for the ioremap, use
pci_resource_len() to get the actual size.
Remove the kernel noise when the ioremap fails and change the error
code from -ENODEV to -ENOMEM.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This variable is only used as a flag to indicate that the pci device
has been enabled and needs to be disabled in the detach. Use the
comedi_device 'iobase' for this and remove the private data variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'result' variable is only used to check the return from
comedi_pci_enable(). Just reuse the 'ret' variable.
Also, remove the kernel noise and use the error code from
comedi_pci_enable() instead of returning -ENODEV.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of the literal string "s626", use the dev->board_name for
the resource name when enabling the PCI device and requesting the
irq.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the hw_dev pointer in the comedi_device struct to hold the
pci_dev instead of carrying it in the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is not optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver only supports one board type. Move the used board info
out of the boardinfo struct and remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add subdevice 1 as an analog input (AI) subdevice. It currently only
supports basic, software-triggered acquisitions.
This is mostly the work of Fred Brooks (MODULE_AUTHOR), but he based his
update on an older version of the driver. I applied the relevant
changes with a few tweaks: adding an explicit `udelay(1)` in a timeout
loop, replacing binary constants with hex, renaming functions, replacing
`printk()` calls, removing exported symbols, removing (very) incomplete
comedi "command" support, and making some coding-style changes.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename `subdev_700_insn()` to `daq700_dio_insn_bits()` and
`subdev_700_insn_config()` to `daq700_dio_insn_config()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename a few functions and variables to use the prefix `daq700` instead
of the prefix or suffix `dio700`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes typedef for
_stCPacketClassificationRuleSI, changes the
name of the struct to bcm_packet_class_rules,
and updates the comments appropriately . In
addition, any calls to typedefs
"CCPacketClassificationRuleSI,
stCPacketClassificationRuleSI,
or *pstCPacketClassificationRuleSI" are changed
to call the struct directly.
Signed-off-by: Kevin McKinney <klmckinney1@gmail.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes typedef for _stPhsRuleSI,
changes the name of the struct to
bcm_phs_rules, and updates the comments
appropriately. In addition, any
calls to typedefs "stPhsRuleSI,
*pstPhsRuleSI, or CPhsRuleSI" are
changed to call the struct directly.
Signed-off-by: Kevin McKinney <klmckinney1@gmail.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
