IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a system with E810 with existing VFs gets rebooted the following
hang may be observed.
Pid 1 is hung in iavf_remove(), part of a network driver:
PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow"
#0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb
#1 [ffffaad04005fae8] schedule at ffffffff8b323e2d
#2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc
#3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930
#4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf]
#5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513
#6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa
#7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc
#8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e
#9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429
#10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4
#11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice]
#12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice]
#13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice]
#14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1
#15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386
#16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870
#17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6
#18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159
#19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc
#20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d
#21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169
#22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b
RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7
RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead
RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90
R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005
R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000
ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b
During reboot all drivers PM shutdown callbacks are invoked.
In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE.
In ice_shutdown() the call chain above is executed, which at some point
calls iavf_remove(). However iavf_remove() expects the VF to be in one
of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If
that's not the case it sleeps forever.
So if iavf_shutdown() gets invoked before iavf_remove() the system will
hang indefinitely because the adapter is already in state __IAVF_REMOVE.
Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE,
as we already went through iavf_shutdown().
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Fixes: a8417330f8 ("iavf: Fix race condition between iavf_shutdown and iavf_remove")
Reported-by: Marius Cornea <mcornea@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When an interface with the maximum number of VLAN filters is brought up,
a spurious error is logged:
[257.483082] 8021q: adding VLAN 0 to HW filter on device enp0s3
[257.483094] iavf 0000:00:03.0 enp0s3: Max allowed VLAN filters 8. Remove existing VLANs or disable filtering via Ethtool if supported.
The VF driver complains that it cannot add the VLAN 0 filter.
On the other hand, the PF driver always adds VLAN 0 filter on VF
initialization. The VF does not need to ask the PF for that filter at
all.
Fix the error by not tracking VLAN 0 filters altogether. With that, the
check added by commit 0e710a3ffd ("iavf: Fix VF driver counting VLAN 0
filters") in iavf_virtchnl.c is useless and might be confusing if left as
it suggests that we track VLAN 0.
Fixes: 0e710a3ffd ("iavf: Fix VF driver counting VLAN 0 filters")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, IAVF's decode_rx_desc_ptype() correctly reports payload type
of L4 for IPv4 UDP packets and IPv{4,6} TCP, but only L3 for IPv6 UDP.
Originally, i40e, ice and iavf were affected.
Commit 73df8c9e3e ("i40e: Correct UDP packet header for non_tunnel-ipv6")
fixed that in i40e, then
commit 638a0c8c88 ("ice: fix incorrect payload indicator on PTYPE")
fixed that for ice.
IPv6 UDP is L4 obviously. Fix it and make iavf report correct L4 hash
type for such packets, so that the stack won't calculate it on CPU when
needs it.
Fixes: 206812b5fc ("i40e/i40evf: i40e implementation for skb_set_hash")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Condition, which checks whether the netdev has hashing enabled is
inverted. Basically, the tagged commit effectively disabled passing flow
hash from descriptor to skb, unless user *disables* it via Ethtool.
Commit a876c3ba59 ("i40e/i40evf: properly report Rx packet hash")
fixed this problem, but only for i40e.
Invert the condition now in iavf and unblock passing hash to skbs again.
Fixes: 857942fd1a ("i40e: Fix Rx hash reported to the stack by our driver")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since the latest Intel hardware does both IWARP and ROCE, rename the
term IWARP in the virtchnl header to be RDMA. Do this for both upper and
lower case instances. Many of the non-virtchnl.h changes were done with
regular expression replacements using perl like:
perl -p -i -e 's/_IWARP/_RDMA/' <files>
perl -p -i -e 's/_iwarp/_rdma/' <files>
and I had to pick up a few instances manually.
The virtchnl.h header has some comments and clarity added around when to
use certain defines.
note: had to fix a checkpatch warning for a long line by wrapping one of
the lines I changed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_replace_primary_mac() utilizes queue_work() to schedule the
watchdog task but that only ensures that the watchdog task is queued
to run. To make sure the watchdog is executed asap use
mod_delayed_work().
Without this patch it may take up to 2s until the watchdog task gets
executed, which may cause long delays when setting the MAC address.
Fixes: a3e839d539 ("iavf: Add usage of new virtchnl format to set default MAC")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove netdev_update_features() from iavf_adminq_task(), as it can cause
deadlocks due to needing rtnl_lock. Instead use the
IAVF_FLAG_SETUP_NETDEV_FEATURES flag to indicate that netdev features need
to be updated in the watchdog task. iavf_set_vlan_offload_features()
and iavf_set_queue_vlan_tag_loc() can be called directly from
iavf_virtchnl_completion().
Suggested-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are seeing an issue where setting the MAC address on iavf fails with
EAGAIN after the 2.5s timeout expires in iavf_set_mac().
There is the following deadlock scenario:
iavf_set_mac(), holding rtnl_lock, waits on:
iavf_watchdog_task (within iavf_wq) to send a message to the PF,
and
iavf_adminq_task (within iavf_wq) to receive a response from the PF.
In this adapter state (>=__IAVF_DOWN), these tasks do not need to take
rtnl_lock, but iavf_wq is a global single-threaded workqueue, so they
may get stuck waiting for another adapter's iavf_watchdog_task to run
iavf_init_config_adapter(), which does take rtnl_lock.
The deadlock resolves itself by the timeout in iavf_set_mac(),
which results in EAGAIN returned to userspace.
Let's break the deadlock loop by changing iavf_wq into a per-adapter
workqueue, so that one adapter's tasks are not blocked by another's.
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This fixes a copy-paste issue where dev_err would log the dst mask even
though it is clearly talking about src.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iavf_init_module() won't destroy workqueue when pci_register_driver()
failed. Call destroy_workqueue() when pci_register_driver() failed to
prevent the resource leak.
Similar to the handling of u132_hcd_init in commit f276e00279
("usb: u132-hcd: fix resource leak")
Fixes: 2803b16c10 ("i40e/i40evf: Use private workqueue")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix a deadlock introduced by commit
974578017f ("iavf: Add waiting so the port is initialized in remove")
due to race condition between iavf_shutdown and iavf_remove, where
iavf_remove stucks forever in while loop since iavf_shutdown already
set __IAVF_REMOVE adapter state.
Fix this by checking if the __IAVF_IN_REMOVE_TASK has already been
set and return if so.
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IAVF_FLAG_INITIAL_MAC_SET prevents waiting on iavf_is_mac_set_handled()
the first time the MAC is set. This breaks gratuitous ARP because the
MAC address has not been updated yet when the gARP packet is sent out.
Current behaviour:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: ee:04:19:14:ec:ea
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:23:41.676611 ee:04:19:14:ec:ea > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
With IAVF_FLAG_INITIAL_MAC_SET removed:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: 3e:8a:16:a2:37:6d
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:28:01.836608 00:11:22:33:44:55 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VF driver mistakenly counts VLAN 0 filters, when no PF driver
counts them.
Do not count VLAN 0 filters, when VLAN_V2 is engaged.
Counting those filters in, will affect filters size by -1, when
sending batched VLAN addition message.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Changed information about device removal in dmesg.
In function iavf_remove changed printed message from
"Remove" to "Removing" after hot vf plug/unplug.
Reason for this change is that, that "Removing" word
is better because it is clearer for the user that
the device is already being removed rather than implying
that the user should remove this device.
Signed-off-by: Bartosz Staszewski <bartoszx.staszewski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After setting port VLAN and MTU to 9000 on VF with ice driver there
was an iavf error
"PF returned error -5 (IAVF_ERR_PARAM) to our request 6".
During queue configuration, VF's max packet size was set to
IAVF_MAX_RXBUFFER but on ice max frame size was smaller by VLAN_HLEN
due to making some space for port VLAN as VF is not aware whether it's
in a port VLAN. This mismatch in sizes caused ice to reject queue
configuration with ERR_PARAM error. Proper max_mtu is sent from ice PF
to VF with GET_VF_RESOURCES msg but VF does not look at this.
In iavf change max_frame from IAVF_MAX_RXBUFFER to max_mtu
received from pf with GET_VF_RESOURCES msg to make vf's
max_frame_size dependent from pf. Add check if received max_mtu is
not in eligible range then set it to IAVF_MAX_RXBUFFER.
Fixes: dab86afdbb ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix bad page state, free inappropriate page in handling dummy
descriptor. iavf_build_skb now has to check not only if rx_buffer is
NULL but also if size is zero, same thing in iavf_clean_rx_irq.
Without this patch driver would free page that will be used
by napi_build_skb.
Fixes: a9f49e0060 ("iavf: Fix handling of dummy receive descriptors")
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously changing mac address gives false negative because
ip link set <interface> address <MAC> return with
RTNLINK: Permission denied.
In iavf_set_mac was check if PF handled our mac set request,
even before filter was added to list.
Because this check returns always true and it never waits for
PF's response.
Move iavf_is_mac_handled to wait_event_interruptible_timeout
instead of false. Now it will wait for PF's response and then
check if address was added or rejected.
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Co-developed-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During stress tests with adding VF to namespace and changing vf's
trust there was a race between iavf_reset_task and iavf_close.
Sometimes when IAVF_FLAG_AQ_DISABLE_QUEUES from iavf_close was sent
to PF after reset and before IAVF_AQ_GET_CONFIG was sent then PF
returns error IAVF_NOT_SUPPORTED to disable queues request and
following requests. There is need to get_config before other
aq_required will be send but iavf_close clears all flags, if
get_config was not sent before iavf_close, then it will not be send
at all.
In case when IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS was sent before
IAVF_FLAG_AQ_DISABLE_QUEUES then there was rtnl_lock deadlock
between iavf_close and iavf_adminq_task until iavf_close timeouts
and disable queues was sent after iavf_close ends.
There was also a problem with sending delete/add filters.
Sometimes when filters was not yet added to PF and in
iavf_close all filters was set to remove there might be a try
to remove nonexistent filters on PF.
Add aq_required_tmp to save aq_required flags and send them after
disable_queues will be handled. Clear flags given to iavf_down
different than IAVF_FLAG_AQ_GET_CONFIG as this flag is necessary
to sent other aq_required. Remove some flags that we don't
want to send as we are in iavf_close and we want to disable
interface. Remove filters which was not yet sent and send del
filters flags only when there are filters to remove.
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_reset_task() takes crit_lock at the beginning and holds
it during whole call. The function subsequently calls
iavf_init_interrupt_scheme() that grabs RTNL. Problem occurs
when userspace initiates during the reset task any ndo callback
that runs under RTNL like iavf_open() because some of that
functions tries to take crit_lock. This leads to classic A-B B-A
deadlock scenario.
To resolve this situation the device should be detached in
iavf_reset_task() prior taking crit_lock to avoid subsequent
ndos running under RTNL and reattach the device at the end.
Fixes: 62fe2a865e ("i40evf: add missing rtnl_lock() around i40evf_set_interrupt_capability")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Tested-by: Vitaly Grinberg <vgrinber@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix deadlock that occurs when iavf interface is a part of failover
configuration.
1. Mutex crit_lock is taken at the beginning of iavf_watchdog_task()
2. Function iavf_init_config_adapter() is called when adapter
state is __IAVF_INIT_CONFIG_ADAPTER
3. iavf_init_config_adapter() calls register_netdevice() that emits
NETDEV_REGISTER event
4. Notifier function failover_event() then calls
net_failover_slave_register() that calls dev_open()
5. dev_open() calls iavf_open() that tries to take crit_lock in
end-less loop
Stack trace:
...
[ 790.251876] usleep_range_state+0x5b/0x80
[ 790.252547] iavf_open+0x37/0x1d0 [iavf]
[ 790.253139] __dev_open+0xcd/0x160
[ 790.253699] dev_open+0x47/0x90
[ 790.254323] net_failover_slave_register+0x122/0x220 [net_failover]
[ 790.255213] failover_slave_register.part.7+0xd2/0x180 [failover]
[ 790.256050] failover_event+0x122/0x1ab [failover]
[ 790.256821] notifier_call_chain+0x47/0x70
[ 790.257510] register_netdevice+0x20f/0x550
[ 790.258263] iavf_watchdog_task+0x7c8/0xea0 [iavf]
[ 790.259009] process_one_work+0x1a7/0x360
[ 790.259705] worker_thread+0x30/0x390
To fix the situation we should check the current adapter state after
first unsuccessful mutex_trylock() and return with -EBUSY if it is
__IAVF_INIT_CONFIG_ADAPTER.
Fixes: 226d528512 ("iavf: fix locking of critical sections")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_alloc_asq_bufs/iavf_alloc_arq_bufs allocates with dma_alloc_coherent
memory for VF mailbox.
Free DMA regions for both ASQ and ARQ in case error happens during
configuration of ASQ/ARQ registers.
Without this change it is possible to see when unloading interface:
74626.583369: dma_debug_device_change: device driver has pending DMA allocations while released from device [count=32]
One of leaked entries details: [device address=0x0000000b27ff9000] [size=4096 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent]
Fixes: d358aa9a7a ("i40evf: init code and hardware support")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix max_rate option in TC, check for proper quanta boundaries.
Check for minimum value provided and if it fits expected 50Mbps
quanta.
Without this patch, iavf could send settings for max_rate limiting
that would be accepted from by PF even the max_rate option is less
than expected 50Mbps quanta. It results in no rate limiting
on traffic as rate limiting will be floored to 0.
Example:
tc qdisc add dev $vf root mqprio num_tc 3 map 0 2 1 queues \
2@0 2@2 2@4 hw 1 mode channel shaper bw_rlimit \
max_rate 50Mbps 500Mbps 500Mbps
Should limit TC0 to circa 50 Mbps
tc qdisc add dev $vf root mqprio num_tc 3 map 0 2 1 queues \
2@0 2@2 2@4 hw 1 mode channel shaper bw_rlimit \
max_rate 0Mbps 100Kbit 500Mbps
Should return error
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jun Zhang <xuejun.zhang@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix debug prints, by adding missing state prints.
Extend iavf_state_str by strings for __IAVF_INIT_EXTENDED_CAPS and
__IAVF_INIT_CONFIG_ADAPTER.
Without this patch, when enabling debug prints for iavf.h, user will
see:
iavf 0000:06:0e.0: state transition from:__IAVF_INIT_GET_RESOURCES to:__IAVF_UNKNOWN_STATE
iavf 0000:06:0e.0: state transition from:__IAVF_UNKNOWN_STATE to:__IAVF_UNKNOWN_STATE
Fixes: 605ca7c5c6 ("iavf: Fix kernel BUG in free_msi_irqs")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jun Zhang <xuejun.zhang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix memory leak caused by not handling dummy receive descriptor properly.
iavf_get_rx_buffer now sets the rx_buffer return value for dummy receive
descriptors. Without this patch, when the hardware writes a dummy
descriptor, iavf would not free the page allocated for the previous receive
buffer. This is an unlikely event but can still happen.
[Jesse: massaged commit message]
Fixes: efa14c3985 ("iavf: allow null RX descriptors")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove from supported_coalesce_params ETHTOOL_COALESCE_MAX_FRAMES
and ETHTOOL_COALESCE_MAX_FRAMES_IRQ. As tx-frames-irq allowed
user to change budget for iavf_clean_tx_irq, remove work_limit
and use define for budget.
Without this patch there would be possibility to change rx/tx-frames
and rx/tx-frames-irq, which for rx/tx-frames did nothing, while for
rx/tx-frames-irq it changed rx/tx-frames and only changed budget
for cleaning NAPI poll.
Fixes: fbb7ddfef2 ("i40evf: core ethtool functionality")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jun Zhang <xuejun.zhang@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
