IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Firmwares advertising the support of triggering 11d algorithm on the
scan results of a regular scan expects driver to send
WMI_11D_SCAN_START_CMDID before sending WMI_START_SCAN_CMDID.
Triggering 11d algorithm on the scan results of a normal scan helps
in completely avoiding a separate 11d scan for determining regdomain.
This indirectly helps in speeding up connections on station
interfaces on the chipsets supporting 11D scan.
To enable this feature, send WMI_11D_SCAN_START_CMDID just before
sending WMI_START_SCAN_CMDID if the firmware advertises
WMI_TLV_SERVICE_SUPPORT_11D_FOR_HOST_SCAN service flag.
WCN6750 & WCN6855 supports this feature.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230315161817.29627-1-quic_mpubbise@quicinc.com
Currently, time taken to scan all supported channels on WCN6750
is ~8 seconds and connection time is almost 10 seconds. WCN6750
supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
channels for scan come around ~100 channels (default case).
Since the chip doesn't have support for DBS (Dual Band Simultaneous),
scans cannot be parallelized resulting in longer scan times.
Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
optimizing the scan for 6 GHz channels will bring down the overall
scan time.
WCN6750 firmware has support to scan a 6 GHz channel based on co-located
AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
results. When a scan request with all supported channel list is enqueued
to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
scan channel flag, firmware will scan only those 6 GHz channels for which
RNR IEs are found in the legacy scan results.
In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
for non-PSC channels. Since there is high probability to find 6 GHz APs
on PSC channels, these channels are always scanned. Only non-PSC channels
are selectively scanned based on cached RNR information from the legacy
scan results.
If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
then scan will happen on all supported channels (default behavior).
With these optimizations, scan time is improved by 1.5-1.8 seconds on
WCN6750. Similar savings have been observed on WCN6855.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323060913.10097-1-quic_mpubbise@quicinc.com
Add some more debug prints in processing regulatory WMI event in order to
increase more debuggability.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-4-quic_adisi@quicinc.com
In order to support different power levels of 6 GHz AP and client,
new WMI event for regulatory - WMI_REG_CHAN_LIST_CC_EXT_EVENTID is
added in firmware. This event provides new parameters required for
6 GHz regulatory rules.
Add support for parsing 2.4 GHz, 5 GHz and 6 GHz reg rules and other
parameters from WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <quic_lavaks@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-3-quic_adisi@quicinc.com
Currently, during regulatory event, 2 GHz/5 GHz is referred
to as 2G/5G including variable names. However, there is no
such entity as 2G or 5G.
Re-name such occurences to its proper name. No functional changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-2-quic_adisi@quicinc.com
Add support to notify tx ack signal values for management
packets to userspace through nl80211 interface.
Advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag
to enable this feature and it will be used for data
packets as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Abinaya Kalaiselvan <quic_akalaise@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221219053844.4084486-1-quic_mkenna@quicinc.com
In the previous behaviour only HE IE in management frames are changed
regarding MU-MIMO configurations and not in hardware. Adding push of
MU-MIMO configurations to the hardware as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00356-QCAHKSWPL_SILICONZ-1
Co-developed-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1666128501-12364-3-git-send-email-quic_msinada@quicinc.com
Set the WMI_SCAN_FLAG_EXT_PASSIVE_SCAN_START_TIME_ENHANCE flag
while sending the scan command. If this flag is enabled when the
incoming scan request comes with a strict start time and its duration
overlaps with next TBTT, then target adjust the start time accordingly
for passive scan. Target supporting this feature will advertise
WMI_TLV_SERVICE_PASSIVE_SCAN_START_TIME_ENHANCE.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221222131720.11368-1-quic_tamizhr@quicinc.com
Fine Timing Measurement(FTM) support is used to measure round trip
time between two nodes.
Enable FTM responder feature using hw_params on supported device.
Since FTM functionality is offloaded to firmware, adding the
interface allows user space to enable or disable FTM responder.
Also add support for advertising the same in extended capabilities.
QCA6390, WCN6855 and WCN6750 do not support this feature.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220044435.10506-1-quic_rajkbhag@quicinc.com
Add support to get the following power save information through debugfs interface,
* Current ps state of the peer
* Time duration since the peer is in power save
* Total duration of the peer spent in power save
Above information is helpful in debugging the issues with power save clients.
This patch also add trace log support for PS timekeeper to track the PS state
change of the peers alongs with the peer MAC address and timestamp.
Use the below commands to get the above power save information,
To know the time_since_station_in_power_save:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/current_ps_duration
To know power_save_duration:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/total_ps_duration
To reset the power_save_duration of all stations connected to AP:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath11k/reset_ps_duration
To enable/disable the ps_timekeeper:
echo Y > /sys/kernel/debug/ieee80211/phyX/ath11k/ps_timekeeper_enable
Y = 1 to enable and Y = 0 to disable.
To record PS timekeeer logs after enabling ps_timekeeper:
trace-cmd record -e ath11k_ps_timekeeper
Tested-on: Tested-on: IPQ8074 WLAN.HK.2.5.0.1-00991-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725054601.14719-1-quic_tamizhr@quicinc.com
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only
when ARP method is used, this causes firmware always to crash when wowlan
is enabled because firmware needs it to be present no matter ARP method
is used or not.
Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by
default.
Also fix below typo:
s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 0f84a156aa3b ("ath11k: Handle keepalive during WoWLAN suspend and resume")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220913044358.2037-1-quic_bqiang@quicinc.com
Fix documentation issues reported by kernel-doc:
- Incorrect use of /** for non-kernel-doc comments
- Mismatch between documented and actual identifiers
- Incorrect identifier syntax
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220909151246.22961-1-quic_jjohnson@quicinc.com
Currently TWT debugfs files required for manually testing the
TWT feature are created only for the AP interfaces; these debugfs
hooks are also required for the station interfaces in order to
test the TWT feature manually, therefore create these debugfs
hooks for station iftype as well.
In the case of station interfaces, TWT is entirely handled in the
firmware based on input parameters passed to it during association
via TWT enable WMI command. In order to manually test this feature,
firmware expects to first disable the TWT feature and then send the
enable command with sta_cong_timer_ms parameter set to 0.
This is true for WCN6750, QCA6390 & WCN6855 hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720135150.22193-2-quic_mpubbise@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
Fix this issue by enabling keepalive before going to suspend
and disabling it after resume back.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506012540.1579604-1-quic_bqiang@quicinc.com
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.
This feature is currently enabled for WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
When the WMI service bits are reported from firmware they are divided into
multiple segments, with 128 bits in each segment. The first segment is
processed by ath11k_wmi_service_bitmap_copy(), the second segment is processed
by ath11k_service_available_event() with WMI_TAG_SERVICE_AVAILABLE_EVENT. When
the service bit exceed 256 bits, then firmware reports it by tag
WMI_TAG_ARRAY_UINT32 in WMI_SERVICE_AVAILABLE_EVENTID.
Currently ath11k does not process the third segment. Upcoming features
need to know if firmware support is available for the features, so add
processing of the third segment.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-2-quic_bqiang@quicinc.com
The maximum number of SSIDs in a for active probe requests is currently
reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver.
The scan_req_params structure only has the capacity to hold 10 SSIDs.
This leads to a buffer overflow which can be triggered from
wpa_supplicant in userspace. When copying the SSIDs into the
scan_req_params structure in the ath11k_mac_op_hw_scan route, it can
overwrite the extraie pointer.
Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe
request will be sent, so totally 64 probe requests supported. So
set both max ssid and bssid to 16 and 4 respectively. Remove the
redundant macros of ssid and bssid.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220329150221.21907-1-quic_kathirve@quicinc.com
Host sets GTK related info to firmware before WoW is enabled, and
gets rekey replay_count and then disables GTK rekey when WoW quits.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-7-git-send-email-quic_cjhuang@quicinc.com
Support ARP and NS offload in WoW state.
Tested this way: put machine A with QCA6390 to WoW state,
ping/ping6 machine A from another machine B, check sniffer to see
any ARP response and Neighbour advertisement from machine A.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-6-git-send-email-quic_cjhuang@quicinc.com
Host needs to set hardware data filter before entering WoW to
let firmware drop needless broadcast/mulitcast frames to avoid
frequent wakeup. Host clears hardware data filter when leaving WoW.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-4-git-send-email-quic_cjhuang@quicinc.com
Implement net-detect feature by setting flag
WIPHY_WOWLAN_NET_DETECT if firmware supports this
feature. Driver sets the related PNO configuration
to firmware before entering WoW and firmware then
scans periodically and wakes up host if a specific
SSID is found.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-3-git-send-email-quic_cjhuang@quicinc.com
Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath10k.
When WoW is configured, ath11k_core_suspend and ath11k_core_resume
are skipped as WoW configuration and hif suspend/resume are done in
ath11k_wow_op_suspend() and ath11k_wow_op_resume().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-2-git-send-email-quic_cjhuang@quicinc.com
These calls are used for debugging and will be required for WFA
certification tests.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220131031043.1295-1-alokad@codeaurora.org
Add debugfs interface "fw_dbglog_config" to configure firmware log level.
Configuration is done via WMI command WMI_DBGLOG_CFG_CMDID.
Command to configure,
echo "<dbglog_param> <values>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
where dbglog_param can be,
1) WMI_DEBUG_LOG_PARAM_LOG_LEVEL - configure log level for a given module
here, <values> = <0xaaaa00bb>, 'aaaa' - module id and 'bb' - loglevel
2) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE - enable debug log for a given vdev
here, <values> = vdev_id
3) WMI_DEBUG_LOG_PARAM_VDEV_DISABLE - disable debug log for a given vdev
except ERROR logs
here, <values> = vdev_id
4) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE_BITMAP - set vdev enable bitmap
here, <values> = vdev_enable_bitmap
5) WMI_DEBUG_LOG_PARAM_MOD_ENABLE_BITMAP - set a given log level to all the
modules specified in the module bitmap. Command to configure for this log param,
$ echo "5 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
6) WMI_DEBUG_LOG_PARAM_WOW_MOD_ENABLE_BITMAP - Wow mode specific logging enable.
Command to configure for this log param,
$ echo "6 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
Sample command usage,
To enable module WLAN_MODULE_WMI and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "1 0x10001" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
To enable module bit map from 32 to 63 and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "5 0xffffffff00000001 1 1" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1642405103-32302-1-git-send-email-quic_seevalam@quicinc.com
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath11k will check the capability, and if it is enabled then
ath11k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath11k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware and also notifies cfg80211.
This only enable rfkill feature for QCA6390, rfkill_pin is all initialized to 0
for other chips in ath11k_hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217102334.14907-1-quic_wgong@quicinc.com
Set DTIM policy to DTIM stick mode, so station follows AP DTIM
interval rather than listen interval which is set in peer assoc cmd.
DTIM stick mode is more preferred per firmware team request.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638948694-15582-1-git-send-email-quic_cjhuang@quicinc.com
The driver reports NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR capability
to upper layer based on the service bit firmware reported. Driver
sets the spoofed flag in scan_ctrl_flag to firmware if upper layer
has enabled this feature in scan request.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638948007-9609-1-git-send-email-quic_cjhuang@quicinc.com
Add handler for WMI_11D_NEW_COUNTRY_EVENTID, WMI_11D_SCAN_START_CMDID,
WMI_11D_SCAN_STOP_CMDID.
After vdev create for STATION, send WMI_11D_SCAN_START_CMDID to firmware
and wait firmware complete it, the scan from mac80211 also need to wait
the 11d scan finished, and send WMI_11D_SCAN_STOP_CMDID to firmware
before vdev delete for STATION.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-4-quic_wgong@quicinc.com
Add handler to send WMI_SET_CURRENT_COUNTRY_CMDID to firmware which
is used for QCA6390 and WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-3-quic_wgong@quicinc.com
Currently there are about 60 channels for 6 GHz, then the size of
chan_list in struct scan_req_params which is 40 is not enough to
fill all the channel list of 6 GHz.
Use dynamic memory to save the channel list of scan.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129110939.15711-1-quic_wgong@quicinc.com
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.
The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.
BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com
Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.
This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.
The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)
Ath11k uses both these configurations to disable credit flow for the
WMI path completely.
Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com
AUTH flag is needed when peer assoc command is sent from host in
security mode for non-assoc cases. Firmware will handle AUTH flag
when client is associating as AUTH flag will be set after key exchange.
For internally provided peer assoc commands from host, there won't be
any key exchange, so AUTH flag is expected to be set in host.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635177786-20854-1-git-send-email-quic_ramess@quicinc.com
It's more descriptive to use the actual enum used by the firmware instead of a
boolean so change ath11k_wmi_pdev_set_ps_mode() to use a boolean.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-1-kvalo@codeaurora.org
When the driver sends a peer create cmd, the firmware responds with
WMI_PEER_CREATE_CONF_EVENTID to confirm the firmware received
WMI_PEER_CREATE_CMDID. Since the peer create conf event is not handled
in ath11k_wmi_tlv_op_rx, we are getting unknown event id warning prints
during peer creation.
Add WMI_PEER_CREATE_CONF_EVENTID in wmi_tlv_event_id and handle
the same as unsupported event id under wmi logs.
warning prints:
[ 4382.230817] ath11k_pci 0000:01:00.0: Unknown eventid: 0x601a
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-9-jouni@codeaurora.org
Firmware blocks all data traffic until the key is plumbed. But, with
software encryption mode, key is never plumbed to firmware. Due to this,
a traffic failure in software encryption mode has been observed. Hence,
firmware has introduced a flag to differentiate software encryption
mode. This flag can be passed during vdev_start command.
Enable WMI_VDEV_START_HW_ENCRYPTION_DISABLED flag in vdev_start command
to notify firmware to disable hardware encryption for a vdev. This is set
if raw mode software encryption is enabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-5-jouni@codeaurora.org
Update the fields of pdev tx and tx firmware stats structure.
Missing fields resulted in wrong fw stats to be displayed as below.
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/
ipq8074\ hw2.0/mac0/fw_stats/pdev_stats | grep Illegal
Illegal rate phy errors 36839112
Note that this struct was missing its members from initial driver
support and this change doesn't introduce/modify the structure for
firmware changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-2-jouni@codeaurora.org
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code a bit according to the use of a flexible-array member in
struct scan_chan_list_params instead of a one-element array, and use the
struct_size() helper.
Also, save 25 (too many) bytes that were being allocated:
$ pahole -C channel_param drivers/net/wireless/ath/ath11k/reg.o
struct channel_param {
u8 chan_id; /* 0 1 */
u8 pwr; /* 1 1 */
u32 mhz; /* 2 4 */
/* Bitfield combined with next fields */
u32 half_rate:1; /* 4:16 4 */
u32 quarter_rate:1; /* 4:17 4 */
u32 dfs_set:1; /* 4:18 4 */
u32 dfs_set_cfreq2:1; /* 4:19 4 */
u32 is_chan_passive:1; /* 4:20 4 */
u32 allow_ht:1; /* 4:21 4 */
u32 allow_vht:1; /* 4:22 4 */
u32 allow_he:1; /* 4:23 4 */
u32 set_agile:1; /* 4:24 4 */
u32 psc_channel:1; /* 4:25 4 */
/* XXX 6 bits hole, try to pack */
u32 phy_mode; /* 8 4 */
u32 cfreq1; /* 12 4 */
u32 cfreq2; /* 16 4 */
char maxpower; /* 20 1 */
char minpower; /* 21 1 */
char maxregpower; /* 22 1 */
u8 antennamax; /* 23 1 */
u8 reg_class_id; /* 24 1 */
/* size: 25, cachelines: 1, members: 21 */
/* sum members: 23 */
/* sum bitfield members: 10 bits, bit holes: 1, sum bit holes: 6 bits */
/* last cacheline: 25 bytes */
} __attribute__((__packed__));
as previously, sizeof(struct scan_chan_list_params) was 32 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[1]; /* 6 25 */
/* size: 32, cachelines: 1, members: 3 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
and now with the flexible array transformation it is just 8 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[]; /* 6 0 */
/* size: 8, cachelines: 1, members: 3 */
/* padding: 2 */
/* last cacheline: 8 bytes */
};
This helps with the ongoing efforts to globally enable -Warray-bounds and
get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823172159.GA25800@embeddedor
For 160 MHz, nss_ratio_enabled flag is added to indicate firmware
supports sending NSS ratio information from firmware as a part of
service ready ext event. Extract this NSS ratio info from service
ready ext event and save this information in ath11k_pdev_cap to
calculate NSS ratio.
Current firmware configurations support two types of NSS ratio
which is WMI_NSS_RATIO_1_NSS for QCN9074 and WMI_NSS_RATIO_1BY2_NSS
for IPQ8074. Based on this two configuration, max supported
NSS getting calculated.
Move ath11k_peer_assoc_h_phymode() before ath11k_peer_assoc_h_vht()
to get arg->peer_phymode updated.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-00097-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Co-developed-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721173615.75637-2-jouni@codeaurora.org
Support setting fixed HE rate/gi/ltf values that we are now able to send
to the kernel using nl80211. The added code is reusing parts of the
existing code path already used for HT/VHT. The new helpers are
symmetric to how we do it for HT/VHT.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00235-QCAHKSWPL_SILICONZ-1
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Co-developed-by: Pradeep Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721173615.75637-1-jouni@codeaurora.org
pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.
Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Survey dump statistics is not displaying channel rx and tx time because
the service flag is not enabled. Enable the service flag "bss_chan_info"
in wmi_resource_config to fetch and print the stats for the specific
pdev.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-2-jouni@codeaurora.org
The flag's purpose is not only meant for ATF configs. Rename atf_config
to flag1, so it can be used for future purposes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-1-jouni@codeaurora.org
There are multiple occurrances of the misspelling of requeued in
the drivers with symbol names and debug text. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210423134133.339751-1-colin.king@canonical.com
The SPR parameter set comprises OBSS PD threshold for SRG
and non SRG and Bitmap of BSS color and partial BSSID. This adds
support to configure fields of SPR element to firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01164-QCAHKSWPL_SILICONZ-1
Tested-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612843714-29174-1-git-send-email-rmanohar@codeaurora.org
