IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The EDAC is a sub-function of the SDRAM Memory Controller. Rename the
node to the appropriate generic node name.
Cc: Stefan M Schaeckeler <sschaeck@cisco.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Stefan Schaeckeler <sschaeck@cisco.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Previously the register interface was not attached to any internal bus,
which is not correct - it lives on the APB.
Cc: Stefan M Schaeckeler <sschaeck@cisco.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Stefan Schaeckeler <sschaeck@cisco.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Now that the i2c-bcm-iproc driver has been fixed to permit reading more
than 63 bytes in a single transaction with commit fd01eecdf959 ("i2c:
iproc: Fix i2c master read more than 63 bytes") we no longer need to
bitbang i2c over GPIOs which was necessary before to allow the
PHYLINK/SFP subsystems to read SFP modules.
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We need this to pass auxdata to all the sdma instances.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The R40 has five I2C controllers. Currently only I2C0 has its pinmux
option defined.
Add the options for the remaining four, and set them as the default,
since each controller has only one possible pinmux configuration.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This series of changes contains fixes for issues recently noticed:
- The ti-sysc interconnect target module driver needs fixes for
mstandby quirk handling and reset delay
- We need to configure am335x-sancloud-bbe to use rgmii-id mode because of
the phy changes done earlier
- NET_SWITCHDEV is no longer selected in Kconfig but a dependency and we
must enable CONFIG_NET_SWITCHDEV to have TI_CPSW_SWITCHDEV
- We are still relying on DEBUG_FS at least for PM configuration, let's
add it back
- We need to update compatible for am437x-gp/epos-evm because of the
recent changes to use generic panels
-----BEGIN PGP SIGNATURE-----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=3muQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.5/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omap variants for v5.5-rc1 cycle
This series of changes contains fixes for issues recently noticed:
- The ti-sysc interconnect target module driver needs fixes for
mstandby quirk handling and reset delay
- We need to configure am335x-sancloud-bbe to use rgmii-id mode because of
the phy changes done earlier
- NET_SWITCHDEV is no longer selected in Kconfig but a dependency and we
must enable CONFIG_NET_SWITCHDEV to have TI_CPSW_SWITCHDEV
- We are still relying on DEBUG_FS at least for PM configuration, let's
add it back
- We need to update compatible for am437x-gp/epos-evm because of the
recent changes to use generic panels
* tag 'omap-for-v5.5/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix missing reset delay handling
ARM: dts: am437x-gp/epos-evm: fix panel compatible
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
Link: https://lore.kernel.org/r/pull-1576254925-709310@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tinker Board / S devices use a special chip variant called rk3288-c
and use different operating points with a higher max frequency.
So add the missing operating points for Tinker Board / S devices, also
increase the vdd_cpu regulator-max-microvolt to 1400000 uV so that the
cpu can operate at 1.8 GHz.
Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20191202153540.26143-1-redchenjs@foxmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the introduction of SSR support in the ADSP PIL we should describe
the SMD edge inside the ADSP PIL node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[luca@z3ntu.xyz: Add label for the smd edge]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20191114175348.288976-2-luca@z3ntu.xyz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
so that SPI NOR device can be probed.
- Fix power button of E60K02 board by removing LDORTC2 regulator.
- A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
remove the boot regression caused by 8267ff89b713 ("ARM: imx: Add
serial number support for i.MX6/7 SoCs").
- A couple of fixes on LS1028A SoC TMU regarding to calibration data
and reboot register configuration.
- Fix a regression seen on imx6ul-evk board by marking always-on for
the regulator that is shared by many peripherals.
- Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd8i+oAAoJEFBXWFqHsHzOSDYH/2clV9RTidg9hYqWV5nuMHry
16+S4LYyWEkKgSZwheMbX13+f0UEMLZxQ1/c/oTlJGa95GppEzNq0ydmfZ22mScH
1I1L1t/AfmxiVB6z3HRS0GZk8uIn7CVPe/PBf8tOm+95qEznOOXljykmB2SHLBP3
KVRSx4OIJ1Nb/IBWmPar7tEkNnLAmI77dTvCZFWbaxep5QTmHX4/dff78eghKmwL
CyYJeINpsZt6a+sXOMbD7UBUx4zWKv50QDFToCRdGWJ4o+e1vp6FM+s/D82vC+3A
ZA8cCt9oRxiDAWiwx7gvlpzNVMyLLW3ork7z+a6shtD2Q4BAbStaSNpIXcVKbtI=
=3SH8
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.5:
- Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
so that SPI NOR device can be probed.
- Fix power button of E60K02 board by removing LDORTC2 regulator.
- A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
remove the boot regression caused by 8267ff89b713 ("ARM: imx: Add
serial number support for i.MX6/7 SoCs").
- A couple of fixes on LS1028A SoC TMU regarding to calibration data
and reboot register configuration.
- Fix a regression seen on imx6ul-evk board by marking always-on for
the regulator that is shared by many peripherals.
- Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.
* tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: e60k02: fix power button
ARM: dts: imx6ul: imx6ul-14x14-evk.dtsi: Fix SPI NOR probing
Link: https://lore.kernel.org/r/20191212122427.GK15858@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for OSD9616P0899-10 96x16 passive matrix display. The
pre-charge period parameters are taken form a OSD9616P0899-10
document, but the display works fine with the default values too.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move to use the new drm panel support in tilcdc together with added
"newhaven,nhd-4.3-480272ef-atxl"-panel support in drm panel-simple.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move to use the new drm panel support in tilcdc together with added
"tfc,s9700rtwv43tr-01b"-panel support in drm panel-simple.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename davinci_mdio DT node "ethernet"->"mdio"
This fixes the following DT schemas check errors:
am3517-craneboard.dt.yaml: ethernet@5c030000: $nodename:0: 'ethernet@5c030000' does not match '^mdio(@.*)?'
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM571x/AM572x/AM574x IDK base boards have HDMI output. Add DT nodes to
am57xx-idk-common.dtsi to enable HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:
- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The devicetree specification recommends using generic node names.
Some ZII dts files already follow such recommendation, but some don't,
so use generic node names for consistency among the ZII dts files.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ZII VF610 Board Rev. B is supposed to have exactly the same I2C config
as Rev. C, including I2C bus recovery settings. Drop redundant I2C
properties that are already specified in vf610-zii-dev.dtsi
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many peripherals are affected by gpio5/2, not just sensors. One of those
is ethernet phy so network boot is current broken.
Fix by renaming reg_sensors and marking it as "always on". Also add a
comment asking for careful testing if this is to be made dynamic in the
future.
The "peri_3v3" naming is similar to imx6sx-sdb and regulator-name is
same string as in schematics (VPERI_3V3).
Fixes: 09e2b1048954 ("ARM: dts: imx6ul-14x14-evk: Add sensors' GPIO regulator")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch sets initial buck regulator modes explicitly to a state this
hardware needs. So a wrong initial mode set by bootloader or pmic itself
does not interfere anymore.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add node for UCS1002 USB charger chip connected to front panel USB and
replace "regulator-fixed" previously used to control VBUS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Otherwise, the system will hang if USB driver try to access
portsc register.
Cc: André Draszik <git@andred.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DDR clock controller and pass it's DDR_CLKID_DDR_PLL to the main
(HHI) clock controller as "ddr_clk". The "ddr_clk" is used as one of the
inputs for the audio clock muxes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the DDR clock controller and pass it's DDR_CLKID_DDR_PLL to the main
(HHI) clock controller as "ddr_clk". The "ddr_clk" is used as one of the
inputs for the audio clock muxes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller driver has provided the XTAL clock so far. This
does not match how the hardware actually works because the XTAL clock is
an actual crystal which is mounted on the PCB.
Add the "xtal" clock to meson.dtsi and replace all references to the
clock controller's CLKID_XTAL with the new xtal clock node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add missing 2.0GHz, 1.9GHz & 1.8GHz OPPs (for A15 cores) and 1.4GHz
OPP (for A7 cores). Also update common Odroid-XU3 Lite/XU3/XU4
thermal cooling maps to account for new OPPs.
Since some new OPPs are not available on all Exynos5422/5800 boards
modify dts files for Odroid XU3 Lite (limited to 1.8 GHz / 1.3 GHz) &
Peach Pi (limited to 2.0 GHz / 1.3 GHz) accordingly.
This patch uses maximum voltages for new OPPs. This is a temporary
solution till proper Exynos ASV support is added.
Also while at it fix the number of cooling down steps for big cores
(should be 11 instead of 12 on Odroid XU3 Lite and 14 on XU3/XU4).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[mszyprow: rebased onto v5.5-rc1 and adapted to recent dts changes,
fixed removal of the 1.4GHz OPP for A7s on Peach-Pi]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Declare Exynos5422/5800 voltage ranges for OPPs for big CPUs
(Cortex-A15) and wcore bus. Couple their voltage supplies as vdd_arm
and vdd_int should be in 300 mV range.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.konieczny: add missing patch description]
Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "syscon" compatible string was introduced in commit ("cdcce1ee977b
ARM: dts: exynos: Add "syscon" compatible string to chipid node on Exynos5")
to allow sharing of the CHIPID IO region between multiple drivers.
However, such sharing can be also done without an additional compatible
so remove the syscon entry.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.
Update the DT files accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the Broadcom uart bluetooth driver on uart0 and gives it
ownership of its gpios. In order to use this, you must enable the
following kconfig options:
- CONFIG_BT_HCIUART_BCM
- CONFIG_SERIAL_DEV
This is applicable to rk3288-veyron series boards that use the bcm43540
wifi+bt chips.
As part of this change, also refactor the pinctrl across the various
boards. All the boards using broadcom bluetooth shouldn't touch the
bt_dev_wake pin.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20191127223909.253873-2-abhishekpandit@chromium.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher
So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).
Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.
Fixes: 0fe4d2181cc4 ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The phy mode should be rgmii-id. For some reason, it used to work with
rgmii-txid but doesn't any more.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Specify the SoC SDCAL pin connection that is used in the
sama5d27c 128MiB SiP on the SAMA5D27 SOM1.
This will put in place a software workaround that would reduce power
consumption on all boards using this SoM, including the SAMA5D27 SOM1 EK.
Uses property introduced in 5cd41fe89704 ("dt-bindings: sdhci-of-at91:
add the microchip,sdcal-inverted property")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191205113604.9000-1-nicolas.ferre@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.
From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.
Fixes: 5e04822f7db5 ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20191203142147.875227-1-inguin@gmx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Beelink X2 box comes with a remote. Add a mapping for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Emlid Neutis N5H3 is a version of Emlid Neutis SoM with H3 instead of H5
inside.
6eeb4180d4b9 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device")
was used as reference.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A new variant of Emlid Neutis has been inroduced. This one uses H3
instead of H5. The boards are essentially the same. This commit moves
non-SoC-specific parts out so that the common parts could be reused with
ease.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
