IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The Tegra driver currently only support a single chip select, hence
check boundaries accordingly. This fixes a off by one issue catched
with Smatch:
drivers/mtd/nand/raw/tegra_nand.c:476 tegra_nand_select_chip()
warn: array off by one? 'nand->cs[die_nr]'
Also warn in case the stack asks for a chip select we currently do
not support.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some timings like tBERS (block erase time), tCCs (change column setup
time), tPROG (page program time) and tR (page read time) are derived
from the ONFI parameter page. They are set in the SDR interface only
if the chip is ONFI compliant.
It makes these timings unreliable and prevent the driver to use one of
these four values with a non-ONFI chip.
Fix this situation by taking the highest possible value (or a default
one) value for each missing timing (stored as unsigned 16-bit entries in
the parameter page).
This makes tBERS and tPROG being ~65ms while typical values are at most
a few milliseconds. As these are timeouts, it is not impacting at all
the performances in nominal use.
tR maximum time and tCCS minimum time (delay to wait after a change
column) are set, according to the ONFI specification, to default 'slow'
values; respectively 200us and 500ns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We already have a dependency on BCMA_NFLASH, which in turn depends on
BCMA, but since BCMA is a tristate option and BCMA_NFLASH is bool,
we can run into an invalid configuration with MTD_NAND_BCM47XXNFLASH=y
and BCMA=m:
drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.o: In function `bcm47xxnflash_ops_bcm4706_init':
ops_bcm4706.c:(.text+0x790): undefined reference to `bcma_chipco_pll_read'
Adding the dependency here forces MTD_NAND_BCM47XXNFLASH to only be
configured =m here so it can link against the BCMA driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In jz_nand_detect_bank(), chipnr is a size_t argument. Use %zu instead
of %i when printing it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix indentation and replace '---help---' by 'help' to make things
consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The first checks in mtdchar_read() and mtdchar_write() attempt to limit
`count` such that `*ppos + count <= mtd->size`. However, they ignore the
possibility of `*ppos > mtd->size`, allowing the calculation of `count` to
wrap around. `mtdchar_lseek()` prevents seeking beyond mtd->size, but the
pread/pwrite syscalls bypass this.
I haven't found any codepath on which this actually causes dangerous
behavior, but it seems like a sensible change anyway.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some MTD sublayers/drivers are implementing ->_read/write() and
not ->_read/write_oob().
While for NAND devices both are usually valid, for NOR devices, using
the _oob variant has no real meaning. But, as the MTD layer is supposed
to hide as much as possible the flash complexity to the user, there is
no reason to error out while it is just a matter of rewritting things
internally.
Add a fallback on mtd->_read() (resp. mtd->_write()) when the user calls
mtd_read_oob() (resp. mtd_write_oob()) while mtd->_read_oob() (resp.
mtd->_write_oob) is not implemented. There is already a fallback on the
_oob variant if the former is used.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This driver doesn't specify parsers so it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This enables some features implemented in mtd subsystem like reading
label and partitioning info from DT.
Reported-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This MACH_JZ4780 dependency is taken care of by JZ4780_NEMC, no need
to repeat it here.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having MACH_JZ4740 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the jz4740_nand driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having SOC_TX4938 or SOC_TX4939
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the ndfmc driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes maintainers' life easier by allowing them to compile-test
this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The local eccstat_regs variable in fsl_ifc_run_command() is missing an
__iomem specifier, and sparce complains about that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having PLAT_SPEAR, ARCH_NOMADIK,
ARCH_U8500 or MACH_U300 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We want to allow this driver to be selected when COMPILE_TEST=y, this
means the driver can be compiled for any arch, including MIPS. When
compiling this driver for MIPS, we end up with a collision on the 'PC'
macro definition (also defined in arch/mips/include/asm/ptrace.h).
Prefix the fsmc one with FSMC_ to avoid this problem.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_SUNXI enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes the following smatch warning:
drivers/mtd/nand/raw/sunxi_nand.c:551 sunxi_nfc_read_byte() error: uninitialized symbol 'ret'.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes the "warning: large integer implicitly truncated to unsigned type
[-Woverflow]" warning when compiled for x86.
This is needed in order to allow compiling this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_DAVINCI or ARCH_KEYSTONE
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rules about Kconfig are simple but in the raw NAND directory indentation
is somehow archaic. Fix the indentation in the whole file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in doing this sort of conversion since we can
replace |= by += operations which are perfectly valid on pointers.
This is done in preparation of COMPILE_TEST addition to the NAND_DAVINCI
Kconfig entry, since building for x86 generates several warnings because
of inappropriate u32 <-> void * conversions (pointers are 64-bit large
on x86_64).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_AT91 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gen_pool_dma_alloc() return type is void *, while internally, the
memory region exposed by the sram driver has been mapped with
ioremap().
Add a void * to void __iomem * cast to make sparse happy.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When casting a pointer to an unsigned int, uintptr_t should be used to
cope with the pointer size differences between 32-bit and 64-bit
architectures.
This is needed if we want to allow compilation of this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Modern NAND controller drivers implement ->exec_op() instead of
->cmdfunc(), make sure we don't end up with a NULL pointer dereference
when hynix_nand_reg_write_op() is called.
Fixes: 8878b126df76 ("mtd: nand: add ->exec_op() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't keep an error-pointer around in the private struct. If this optional
clock can't be obtained, simply set the pointer to NULL instead so we can
use clk_prepare_enable() on it without further checks,
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The comment in marvell_nfc_select_chip() about ndtr0 and ndtr1 didn't
reflect what the driver was doing.
The values of NDTR0 and NDTR1 are read from the registers at probe time
and a copy is retained in 'struct marvell_nand_chip'. If keep-config is
set in the DT properties, there are no other writers of these timing
variables so they can safely be used when the chip is selected.
As suggested by Miquel Raynal, simply remove the comment.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch restores the suspend and resume hooks that the old driver used
to have. Apart from stopping and starting the clocks, the resume callback
also nullifies the selected_chip pointer, so the next command that is issued
will re-select the chip and thereby restore the timing registers.
Factor out some code from marvell_nfc_init() into a new function
marvell_nfc_reset() and also call it at resume time to reset some registers
that don't retain their contents during low-power mode.
Without this patch, a PXA3xx based system would cough up an error similar to
the one below after resume.
[ 44.660162] marvell-nfc 43100000.nand-controller: Timeout waiting for RB signal
[ 44.671492] ubi0 error: ubi_io_write: error -110 while writing 2048 bytes to PEB 102:38912, written 0 bytes
[ 44.682887] CPU: 0 PID: 1417 Comm: remote-control Not tainted 4.18.0-rc2+ #344
[ 44.691197] Hardware name: Marvell PXA3xx (Device Tree Support)
[ 44.697111] Backtrace:
[ 44.699593] [<c0106458>] (dump_backtrace) from [<c0106718>] (show_stack+0x18/0x1c)
[ 44.708931] r7:00000800 r6:00009800 r5:00000066 r4:c6139000
[ 44.715833] [<c0106700>] (show_stack) from [<c0678a60>] (dump_stack+0x20/0x28)
[ 44.724206] [<c0678a40>] (dump_stack) from [<c0456cbc>] (ubi_io_write+0x3d4/0x630)
[ 44.732925] [<c04568e8>] (ubi_io_write) from [<c0454428>] (ubi_eba_write_leb+0x690/0x6fc)
...
Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the board files are overloading those hooks, so let's drop them
from struct platform_nand_ctrl.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the boards seem to overload the ->dev_ready() hook, just drop
this field from orion_nand_data.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the existing drivers are overloading the ->scan_bbt() method,
let's get rid of it and replace calls to ->scan_bbt() by
nand_create_bbt() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rename nand_default_bbt() into nand_create_bbt() and pass it a nand_chip
object to prepare removal of the chip->scan_bbt() hook.
We add a temporary nand_default_bbt() wrapper which will be dropped
after the removal of ->scan_bbt().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Leaving a function pointer to NULL should be enough to trigger a NULL
pointer exception, and anyway, if we want to BUG() when some missing
hooks are called, this should be done in the core, so let's drop the
cafe_nand_bug() dummy function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_W90X900 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_QCOM enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_MXC enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
asm/mach/flash.h does not seem to be needed, drop this #include to make
the code completely machine and arch independent and allow one to
compile it when COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARM, ARM64 or MIPS enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test these drivers without having ARCH_LPC32XX enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_PXA enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
