IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Re-reading a recently merged fix to the raw_gadget driver showed that
it inadvertently introduced a double-free bug in a failure pathway.
If raw_ioctl_init() encounters an error after the driver ID number has
been allocated, it deallocates the ID number before returning. But
when dev_free() runs later on, it will then try to deallocate the ID
number a second time.
Closely related to this issue is another error in the recent fix: The
ID number is stored in the raw_dev structure before the code checks to
see whether the structure has already been initialized, in which case
the new ID number would overwrite the earlier value.
The solution to both bugs is to keep the new ID number in a local
variable, and store it in the raw_dev structure only after the check
for prior initialization. No errors can occur after that point, so
the double-free will never happen.
Fixes: f2d8c26068 ("usb: gadget: Fix non-unique driver names in raw-gadget driver")
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YrMrRw5AyIZghN0v@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for 5.19-rc4
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
* tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel RM500K module support
USB: serial: option: add Quectel EM05-G modem
USB: serial: pl2303: add support for more HXN (G) types
USB: serial: option: add Telit LE910Cx 0x1250 composition
Add support for further HXN (G) type devices (GT variant, GL variant, GS
variant and GR) and document the bcdDevice mapping.
Note that the TA and TB types use the same bcdDevice as some GT and GE
variants, respectively, but that the HX status request can be used to
determine which is which.
Also note that we currently do not distinguish between the various HXN
(G) types in the driver but that this may change eventually (e.g. when
adding GPIO support).
Reported-by: Charles Yeh <charlesyeh522@gmail.com>
Link: https://lore.kernel.org/r/YrF77b9DdeumUAee@hovoldconsulting.com
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A panic can occur if the endpoint becomes disabled and the
uvcg_video_pump adds the request back to the req_free list after it has
already been queued to the endpoint. The endpoint complete will add the
request back to the req_free list. Invalidate the local request handle
once it's been queued.
<6>[ 246.796704][T13726] configfs-gadget gadget: uvc: uvc_function_set_alt(1, 0)
<3>[ 246.797078][ T26] list_add double add: new=ffffff878bee5c40, prev=ffffff878bee5c40, next=ffffff878b0f0a90.
<6>[ 246.797213][ T26] ------------[ cut here ]------------
<2>[ 246.797224][ T26] kernel BUG at lib/list_debug.c:31!
<6>[ 246.807073][ T26] Call trace:
<6>[ 246.807180][ T26] uvcg_video_pump+0x364/0x38c
<6>[ 246.807366][ T26] process_one_work+0x2a4/0x544
<6>[ 246.807394][ T26] worker_thread+0x350/0x784
<6>[ 246.807442][ T26] kthread+0x2ac/0x320
Fixes: f9897ec0f6 ("usb: gadget: uvc: only pump video data if necessary")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220617163154.16621-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a report for a separate bug (which has already been fixed by commit
5f0b5f4d50 "usb: gadget: fix race when gadget driver register via
ioctl") in the raw-gadget driver, the syzbot console log included
error messages caused by attempted registration of a new driver with
the same name as an existing driver:
> kobject_add_internal failed for raw-gadget with -EEXIST, don't try to register things with the same name in the same directory.
> UDC core: USB Raw Gadget: driver registration failed: -17
> misc raw-gadget: fail, usb_gadget_register_driver returned -17
These errors arise because raw_gadget.c registers a separate UDC
driver for each of the UDC instances it creates, but these drivers all
have the same name: "raw-gadget". Until recently this wasn't a
problem, but when the "gadget" bus was added and UDC drivers were
registered on this bus, it became possible for name conflicts to cause
the registrations to fail. The reason is simply that the bus code in
the driver core uses the driver name as a sysfs directory name (e.g.,
/sys/bus/gadget/drivers/raw-gadget/), and you can't create two
directories with the same pathname.
To fix this problem, the driver names used by raw-gadget are made
distinct by appending a unique ID number: "raw-gadget.N", with a
different value of N for each driver instance. And to avoid the
proliferation of error handling code in the raw_ioctl_init() routine,
the error return paths are refactored into the common pattern (goto
statements leading to cleanup code at the end of the routine).
Link: https://lore.kernel.org/all/0000000000008c664105dffae2eb@google.com/
Fixes: fc274c1e99 "USB: gadget: Add a new bus for gadgets"
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+02b16343704b3af1667e@syzkaller.appspotmail.com
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YqdG32w+3h8c1s7z@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today's linux-next merge of the extcon tree got a conflict in:
drivers/usb/dwc3/drd.c
between commit:
0f01017191 ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
from the usb tree and commit:
88490c7f43c4 ("extcon: Fix extcon_get_extcon_dev() error handling")
from the extcon tree.
I fixed it up (the former moved the code modified by the latter, so I
used the former version of this files and added the following merge fix
patch) and can carry the fix as necessary.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220426152739.62f6836e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In systemd systems setting a fixed MAC address through
the "dev_addr" module argument fails systematically.
When checking the MAC address after the interface is created
it always has the same but different MAC address to the one
supplied as argument.
This is partially caused by systemd which by default will
set an internally generated permanent MAC address for interfaces
that are marked as having a randomly generated address.
Commit 890d5b4090 ("usb: gadget: u_ether: fix race in
setting MAC address in setup phase") didn't take into account
the fact that the interface must be marked as having a set
MAC address when it's set as module argument.
Fixed by marking the interface with NET_ADDR_SET when
the "dev_addr" module argument is supplied.
Fixes: 890d5b4090 ("usb: gadget: u_ether: fix race in setting MAC address in setup phase")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20220603153459.32722-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 582ab24e09 ("usb: dwc3: pci: Set "linux,phy_charger_detect"
property on some Bay Trail boards") added a new swnode similar to the
existing ones for boards where the PHY handles charger detection.
Unfortunately, the "linux,sysdev_is_parent" property got lost in the
merge conflict resolution of commit ca9400ef7f ("Merge 5.17-rc6 into
usb-next"). Now dwc3_pci_intel_phy_charger_detect_properties is the
only swnode in dwc3-pci that is missing "linux,sysdev_is_parent".
It does not seem to cause any obvious functional issues, but it's
certainly unintended so restore the line to make the properties
consistent again.
Fixes: ca9400ef7f ("Merge 5.17-rc6 into usb-next")
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220528170913.9240-1-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic to assign the max packet limit for IN endpoints attempts
to take the default HW value and apply the optimal endpoint settings based
on it. However, if the default value reports a TxFIFO size large enough
for only one max packet, it will divide the value and assign a smaller ep
max packet limit.
For example, if the default TxFIFO size fits 1024B, current logic will
assign 1024/3 = 341B to ep max packet size. If function drivers attempt to
request for an endpoint with a wMaxPacketSize of 1024B (SS BULK max packet
size) then it will fail, as the gadget is unable to find an endpoint which
can fit the requested size.
Functionally, if the TxFIFO has enough space to fit one max packet, it will
be sufficient, at least when initializing the endpoints.
Fixes: d94ea53198 ("usb: dwc3: gadget: Properly set maxpacket limit")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220523213948.22142-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
Pull more ACPI updates from Rafael Wysocki:
"These add some new device IDs, update a few drivers (processor,
battery, backlight) and clean up code in a few places.
Specifics:
- Add Meteor Lake ACPI IDs for DPTF devices (Sumeet Pawnikar)
- Rearrange find_child_checks() to simplify code (Rafael Wysocki)
- Use memremap() to map the UCSI mailbox that is always in main
memory and drop acpi_release_memory() that has no more users
(Heikki Krogerus, Dan Carpenter)
- Make max_cstate/nocst/bm_check_disable processor module parameters
visible in sysfs (Yajun Deng)
- Fix typo in the CPPC driver (Julia Lawall)
- Make the ACPI battery driver show the "not-charging" status by
default unless "charging" or "full" is directly indicated (Werner
Sembach)
- Improve the PM notifier in the ACPI backlight driver (Zhang Rui)
- Clean up some white space in the ACPI code (Ian Cowan)"
* tag 'acpi-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
usb: typec: ucsi: acpi: fix a NULL vs IS_ERR() check in probe
ACPI: DPTF: Support Meteor Lake
ACPI: CPPC: fix typo in comment
ACPI: video: improve PM notifer callback
ACPI: clean up white space in a few places for consistency
ACPI: glue: Rearrange find_child_checks()
ACPI: processor: idle: Expose max_cstate/nocst/bm_check_disable read-only in sysfs
ACPI: battery: Make "not-charging" the default on no charging or full info
ACPI: OSL: Remove the helper for deactivating memory region
usb: typec: ucsi: acpi: Map the mailbox with memremap()
Merge general ACPI cleanups and processor support updates for 5.19-rc1:
- Rearrange find_child_checks() to simplify code (Rafael Wysocki).
- Use memremap() to map the UCSI mailbox that is always in main memory
and drop acpi_release_memory() that has no more users (Heikki
Krogerus, Dan Carpenter).
- Make max_cstate/nocst/bm_check_disable processor module parameters
visible in sysfs (Yajun Deng).
- Fix typo in the CPPC driver (Julia Lawall).
* acpi-glue:
ACPI: glue: Rearrange find_child_checks()
* acpi-osl:
usb: typec: ucsi: acpi: fix a NULL vs IS_ERR() check in probe
ACPI: OSL: Remove the helper for deactivating memory region
usb: typec: ucsi: acpi: Map the mailbox with memremap()
* acpi-processor:
ACPI: processor: idle: Expose max_cstate/nocst/bm_check_disable read-only in sysfs
* acpi-cppc:
ACPI: CPPC: fix typo in comment
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
Johan writes:
USB-serial updates for 5.19-rc1
Here are the USB-serial updates for 5.19-rc1, including:
- a workaround for pl2303 devices with unexpected bcdUSB
- a new modem device id
Included is also a printk clean up.
All but the modem-id commit have been in linux-next with no reported
issues.
* tag 'usb-serial-5.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
USB: serial: ftdi_sio: clean up printk format specifier
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Example call stack:
Thread#1:
dwc3_thread_interrupt()
spin_lock
-> dwc3_process_event_buf()
-> dwc3_process_event_entry()
-> dwc3_endpoint_interrupt()
-> dwc3_gadget_endpoint_trbs_complete()
-> dwc3_gadget_ep_cleanup_completed_requests()
...
-> dwc3_giveback()
spin_unlock
Thread#2 executes
Thread#2:
configfs_composite_disconnect()
-> __composite_disconnect()
-> ffs_func_disable()
-> ffs_func_set_alt()
-> ffs_func_eps_disable()
-> usb_ep_disable()
wait for dwc3 spin_lock
Thread#1 released lock
clear endpoint.desc
Fixes: 2628844812 ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have USB compositions which may require multiple endpoints.
To get better performance, need bigger CDNS3_EP_BUF_SIZE.
But bigger CDNS3_EP_BUF_SIZE may exceed total hardware FIFO size when
multiple endpoints.
By introducing the check_config() callback, calculate CDNS3_EP_BUF_SIZE.
Move CDNS3_EP_BUF_SIZE into cnds3_device: ep_buf_size
Combine CDNS3_EP_ISO_SS_BURST and CDNS3_EP_ISO_HS_MULT into
cnds3_device:ep_iso_burst
Using a simple algorithm to calculate ep_buf_size.
ep_buf_size = ep_iso_burst = (onchip_buffers - 2k) / (number of IN EP +
1).
Test at 8qxp:
Gadget ep_buf_size
RNDIS: 5
RNDIS+ACM: 3
Mass Storage + NCM + ACM 2
Previous CDNS3_EP_BUF_SIZE is 4, RNDIS + ACM will be failure because
exceed FIFO memory.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220509164055.1815081-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the databook ep0 should be in setup phase during reset.
If host issues reset between control transfers, ep0 will be in an
invalid state. Fix this by issuing stall and restart on ep0 if it
is not in setup phase.
Also SW needs to complete pending control transfer and setup core for
next setup stage as per data book. Hence check ep0 state during reset
interrupt handling and make sure active transfers on ep0 out/in
endpoint are stopped by queuing ENDXFER command for that endpoint and
restart ep0 out again to receive next setup packet.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1651693001-29891-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
initcall_debug shows that OHCI controllers take ~60ms to probe on
Rockchip RK3399 systems:
probe of fe3a0000.usb returned 1 after 58941 usecs
A few of these can add up to waste non-trivial amounts of time at boot.
These host controllers don't provide resources to other drivers, so
this shouldn't contribute to exposing race conditions.
Chrome OS kernels have carried this patch on some systems for a while
without issues. Similar patches have been merged for a variety of (e)MMC
host controllers for similar reasons.
[Brian: rewrote commit message, refreshed, but retained dtor's original
authorship ]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220518150150.1.Ie8ea0e945a9c15066237014be219eed60066d493@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running the driver through kasan gives an interesting splat:
BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c
Read of size 20 at addr f1db2e64 by task swapper/0/1
(...)
isp1760_register from isp1760_plat_probe+0x1d8/0x220
(...)
This happens because the loop reading the regmap fields for the
different ISP1760 variants look like this:
for (i = 0; i < HC_FIELD_MAX; i++) { ... }
Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long.
However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[],
isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are
dynamically sized during compilation.
Fix this by putting an empty assignment to the [HC_FIELD_MAX]
and [DC_FIELD_MAX] array member at the end of each array.
This will make the array one member longer than it needs to be,
but avoids the risk of overwriting whatever is inside
[HC_FIELD_MAX - 1] and is simple and intuitive to read. Also
add comments explaining what is going on.
Fixes: 1da9e1c068 ("usb: isp1760: move to regmap for register access")
Cc: stable@vger.kernel.org
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220516091424.391209-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support for xHCI controllers with only one roothub, and the code
to defer primary roothub registation until second roothub got merged
to usb-next for 5.19 at the same time.
commit 873f323618 ("xhci: prepare for operation w/o shared hcd")
commit b7a4f9b5d0 ("xhci: Set HCD flag to defer primary roothub
registration")
These got merged in such a way that the flag to defer primary roothub
registration is set even for xHC controllers with just one roothub.
Fix this by setting the defer flag in a codepath taken only if we have
two roothubs
Fixes: 873f323618 ("xhci: prepare for operation w/o shared hcd")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220516094850.19788-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a private macro for an invalid grant reference use
the common one.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
