IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
We need to transmit more restrictions in future patches, convert this
one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are unable to ping a bridge on top of a felix switch which
uses the ocelot-8021q tagger. The packets are dropped on the ingress of
the user port and the 'drop_local' counter increments (the counter which
denotes drops due to no valid destinations).
Dumping the PGID tables, it becomes clear that the PGID_SRC of the user
port is zero, so it has no valid destinations.
But looking at the code, the cpu_fwd_mask (the bit mask of DSA tag_8021q
ports) is clearly missing from the forwarding mask of ports that are
under a bridge. So this has always been broken.
Looking at the version history of the patch, in v7
https://patchwork.kernel.org/project/netdevbpf/patch/20210125220333.1004365-12-olteanv@gmail.com/
the code looked like this:
/* Standalone ports forward only to DSA tag_8021q CPU ports */
unsigned long mask = cpu_fwd_mask;
(...)
} else if (ocelot->bridge_fwd_mask & BIT(port)) {
mask |= ocelot->bridge_fwd_mask & ~BIT(port);
while in v8 (the merged version)
https://patchwork.kernel.org/project/netdevbpf/patch/20210129010009.3959398-12-olteanv@gmail.com/
it looked like this:
unsigned long mask;
(...)
} else if (ocelot->bridge_fwd_mask & BIT(port)) {
mask = ocelot->bridge_fwd_mask & ~BIT(port);
So the breakage was introduced between v7 and v8 of the patch.
Fixes: e21268efbe26 ("net: dsa: felix: perform switch setup for tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210817160425.3702809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:
- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
which are written with their hardware default values, also runtime
invariants. So it makes no sense to write these during every .ndo_open.
- PORTID_VAL: this field has an out-of-reset value of zero for all ports
and must be initialized by software. Additionally, the
ocelot_setup_logical_port_ids() code path sets up different logical
port IDs for the ports in a hardware LAG, and we absolutely don't want
.ndo_open to interfere there and reset those values.
So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.
ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.
So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because flow control is set up statically in ocelot_init_port(), and not
in phylink_mac_link_up(), what happens is that after the blamed commit,
the flow control remains disabled after the port flushing procedure.
Fixes: eb4733d7cffc ("net: dsa: felix: implement port flushing on .phylink_mac_link_down")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a tralling */ on a separate line for block comments.
Signed-off-by: Yixing Liu <liuyixing1@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.
I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.
We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.
We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when extracting frames from CPU the cpuq is not used anymore so
remove it.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new PGID that is used not to forward frames anywhere. It is used
by MRP to make sure that MRP Test frames will not reach CPU port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch is confused by the fact that a 32-bit BIT(port) macro is passed
as argument to the ocelot_ifh_set_dest function and warns:
ocelot_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
seville_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
The destination port mask is copied into a 12-bit field of the packet,
starting at bit offset 67 and ending at 56.
So this DSA tagging protocol supports at most 12 bits, which is clearly
less than 32. Attempting to send to a port number > 12 will cause the
packing() call to truncate way before there will be 32-bit truncation
due to type promotion of the BIT(port) argument towards u64.
Therefore, smatch's fears that BIT(port) will do the wrong thing and
cause unexpected truncation for "port" values >= 32 are unfounded.
Nonetheless, let's silence the warning by explicitly passing an u64
value to ocelot_ifh_set_dest, such that the compiler does not need to do
a questionable type promotion.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.
We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.
Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be unconditionally enabling address learning, since doing
that is actively detrimential when a port is standalone and not offloading
a bridge. Namely, if a port in the switch is standalone and others are
offloading the bridge, then we could enter a situation where we learn an
address towards the standalone port, but the bridged ports could not
forward the packet there, because the CPU is the only path between the
standalone and the bridged ports. The solution of course is to not
enable address learning unless the bridge asks for it.
We need to set up the initial port flags for no learning and flooding
everything, and also when the port joins and leaves the bridge.
The flood configuration was already configured ok for standalone mode
in ocelot_init, we just need to disable learning in ocelot_init_port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of offloading the bridge port flags which have
independent settings for unknown multicast and for broadcast, we should
also start reserving one destination Port Group ID for the flooding of
broadcast packets, to allow configuring it individually.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.
Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.
Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It makes it a bit easier to read and understand the code that deals with
balancing the 16 aggregation codes among the ports in a certain LAG.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.
In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The setup of logical port IDs is done in two places: from the inconclusively
named ocelot_setup_lag and from ocelot_port_lag_leave, a function that
also calls ocelot_setup_lag (which apparently does an incomplete setup
of the LAG).
To improve this situation, we can rename ocelot_setup_lag into
ocelot_setup_logical_port_ids, and drop the "lag" argument. It will now
set up the logical port IDs of all switch ports, which may be just
slightly more inefficient but more maintainable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The index of the LAG is equal to the logical port ID that all the
physical port members have, which is further equal to the index of the
first physical port that is a member of the LAG.
The code gets a bit carried away with logic like this:
if (a == b)
c = a;
else
c = b;
which can be simplified, of course, into:
c = b;
(with a being port, b being lp, c being lag)
This further makes the "lp" variable redundant, since we can use "lag"
everywhere where "lp" (logical port) was used. So instead of a "c = b"
assignment, we can do a complete deletion of b. Only one comment here:
if (bond_mask) {
lp = __ffs(bond_mask);
ocelot->lags[lp] = 0;
}
lp was clobbered before, because it was used as a temporary variable to
hold the new smallest port ID from the bond. Now that we don't have "lp"
any longer, we'll just avoid the temporary variable and zeroize the
bonding mask directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.
We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 header information is not currently part of the entropy source for
the 4-bit aggregation code used for LAG offload, even though it could be.
The hardware reference manual says about these fields:
ANA::AGGR_CFG.AC_IP6_TCPUDP_PORT_ENA
Use IPv6 TCP/UDP port when calculating aggregation code. Configure
identically for all ports. Recommended value is 1.
ANA::AGGR_CFG.AC_IP6_FLOW_LBL_ENA
Use IPv6 flow label when calculating AC. Configure identically for all
ports. Recommended value is 1.
Integration with the xmit_hash_policy of the bonding interface is TBD.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since switchdev/DSA exposes network interfaces that fulfill many of the
same user space expectations that dedicated NICs do, it makes sense to
not deny bonding interfaces with a bonding policy that we cannot offload,
but instead allow the bonding driver to select the egress interface in
software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unlike sja1105, the only other user of the software-defined tag_8021q.c
tagger format, the implementation we choose for the Felix DSA switch
driver preserves full functionality under a vlan_filtering bridge
(i.e. IP termination works through the DSA user ports under all
circumstances).
The tag_8021q protocol just wants:
- Identifying the ingress switch port based on the RX VLAN ID, as seen
by the CPU. We achieve this by using the TCAM engines (which are also
used for tc-flower offload) to push the RX VLAN as a second, outer
tag, on egress towards the CPU port.
- Steering traffic injected into the switch from the network stack
towards the correct front port based on the TX VLAN, and consuming
(popping) that header on the switch's egress.
A tc-flower pseudocode of the static configuration done by the driver
would look like this:
$ tc qdisc add dev <cpu-port> clsact
$ for eth in swp0 swp1 swp2 swp3; do \
tc filter add dev <cpu-port> egress flower indev ${eth} \
action vlan push id <rxvlan> protocol 802.1ad; \
tc filter add dev <cpu-port> ingress protocol 802.1Q flower
vlan_id <txvlan> action vlan pop \
action mirred egress redirect dev ${eth}; \
done
but of course since DSA does not register network interfaces for the CPU
port, this configuration would be impossible for the user to do. Also,
due to the same reason, it is impossible for the user to inadvertently
delete these rules using tc. These rules do not collide in any way with
tc-flower, they just consume some TCAM space, which is something we can
live with.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Context: Ocelot switches put the injection/extraction frame header in
front of the Ethernet header. When used in NPI mode, a DSA master would
see junk instead of the destination MAC address, and it would most
likely drop the packets. So the Ocelot frame header can have an optional
prefix, which is just "ff:ff:ff:ff:ff:fe > ff:ff:ff:ff:ff:ff" padding
put before the actual tag (still before the real Ethernet header) such
that the DSA master thinks it's looking at a broadcast frame with a
strange EtherType.
Unfortunately, a lesson learned in commit 69df578c5f4b ("net: mscc:
ocelot: eliminate confusion between CPU and NPI port") seems to have
been forgotten in the meanwhile.
The CPU port module and the NPI port have independent settings for the
length of the tag prefix. However, the driver is using the same variable
to program both of them.
There is no reason really to use any tag prefix with the CPU port
module, since that is not connected to any Ethernet port. So this patch
makes the inj_prefix and xtr_prefix variables apply only to the NPI
port (which the switchdev ocelot_vsc7514 driver does not use).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Applying the bridge forwarding mask currently is done only on the STP
state changes for any port. But it depends on both STP state changes,
and bonding interface state changes. Export the bit that recalculates
the forwarding mask so that it could be reused, and call it when a port
starts and stops offloading a bonding interface.
Now that the logic is split into a separate function, we can rename "p"
into "port", since the "port" variable was already taken in
ocelot_bridge_stp_state_set. Also, we can rename "i" into "lag", to make
it more clear what is it that we're iterating through.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075b2 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e7345 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d6b ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d1c ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multicast entries in the MAC table use the high bits of the MAC
address to encode the ports that should get the packets. But this port
mask does not work for the CPU port, to receive these packets on the
CPU port the MAC_CPU_COPY flag must be set.
Because of this IPv6 was effectively not working because neighbor
solicitations were never received. This was not apparent before commit
9403c158 (net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb
entries) as the IPv6 entries were broken so all incoming IPv6
multicast was then treated as unknown and flooded on all ports.
To fix this problem rework the ocelot_mact_learn() to set the
MAC_CPU_COPY flag when a multicast entry that target the CPU port is
added. For this we have to read back the ports endcoded in the pseudo
MAC address by the caller. It is not a very nice design but that avoid
changing the callers and should make backporting easier.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Fixes: 9403c158b872 ("net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries")
Link: https://lore.kernel.org/r/20210119140638.203374-1-alban.bedel@aerq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using devlink-sb, we can configure 12/16 (the important 75%) of the
switch's controlling watermarks for congestion drops, and we can monitor
50% of the watermark occupancies (we can monitor the reservation
watermarks, but not the sharing watermarks, which are exposed as pool
sizes).
The following definitions can be made:
SB_BUF=0 # The devlink-sb for frame buffers
SB_REF=1 # The devlink-sb for frame references
POOL_ING=0 # The pool for ingress traffic. Both devlink-sb instances
# have one of these.
POOL_EGR=1 # The pool for egress traffic. Both devlink-sb instances
# have one of these.
Editing the hardware watermarks is done in the following way:
BUF_xxxx_I is accessed when sb=$SB_BUF and pool=$POOL_ING
REF_xxxx_I is accessed when sb=$SB_REF and pool=$POOL_ING
BUF_xxxx_E is accessed when sb=$SB_BUF and pool=$POOL_EGR
REF_xxxx_E is accessed when sb=$SB_REF and pool=$POOL_EGR
Configuring the sharing watermarks for COL_SHR(dp=0) is done implicitly
by modifying the corresponding pool size. By default, the pool size has
maximum size, so this can be skipped.
devlink sb pool set pci/0000:00:00.5 sb $SB_BUF pool $POOL_ING \
size 129840 thtype static
Since by default there is no buffer reservation, the above command has
maxed out BUF_COL_SHR_I(dp=0).
Configuring the per-port reservation watermark (P_RSRV) is done in the
following way:
devlink sb port pool set pci/0000:00:00.5/0 sb $SB_BUF \
pool $POOL_ING th 1000
The above command sets BUF_P_RSRV_I(port 0) to 1000 bytes. After this
command, the sharing watermarks are internally reconfigured with 1000
bytes less, i.e. from 129840 bytes to 128840 bytes.
Configuring the per-port-tc reservation watermarks (Q_RSRV) is done in
the following way:
for tc in {0..7}; do
devlink sb tc bind set pci/0000:00:00.5/0 sb 0 tc $tc \
type ingress pool $POOL_ING \
th 3000
done
The above command sets BUF_Q_RSRV_I(port 0, tc 0..7) to 3000 bytes.
The sharing watermarks are again reconfigured with 24000 bytes less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is meant to be a gentle introduction into the world of watermarks
on ocelot. The code is placed in ocelot_devlink.c because it will be
integrated with devlink, even if it isn't right now.
My first step was intended to be to replicate the default configuration
of the congestion watermarks programatically, since they are now going
to be tuned by the user.
But after studying and understanding through trial and error how they
work, I now believe that the configuration used out of reset does not do
justice to the word "reservation", since the sum of all reservations
exceeds the total amount of resources (otherwise said, all reservations
cannot be fulfilled at the same time, which means that, contrary to the
reference manual, they don't guarantee anything).
As an example, here's a dump of the reservation watermarks for frame
buffers, for port 0 (for brevity, the ports 1-6 were omitted, but they
have the same configuration):
BUF_Q_RSRV_I(port 0, prio 0) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 1) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 2) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 3) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 4) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 5) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 6) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 7) = max 3000 bytes
Otherwise said, every port-tc has an ingress reservation of 3000 bytes,
and there are 7 ports in VSC9959 Felix (6 user ports and 1 CPU port).
Concentrating only on the ingress reservations, there are, in total,
8 [traffic classes] x 7 [ports] x 3000 [bytes] = 168,000 bytes of memory
reserved on ingress.
But, surprise, Felix only has 128 KB of packet buffer in total...
A similar thing happens with Seville, which has a larger packet buffer,
but also more ports, and the default configuration is also overcommitted.
This patch disables the (apparently) bogus reservations and moves all
resources to the shared area. This way, real reservations can be set up
by the user, using devlink-sb.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of reading these values from the reference manual and writing
them down into the driver, it appears that the hardware gives us the
option of detecting them dynamically.
The number of frame references corresponds to what the reference manual
notes, however it seems that the frame buffers are reported as slightly
less than the books would indicate. On VSC9959 (Felix), the books say it
should have 128KB of packet buffer, but the registers indicate only
129840 bytes (126.79 KB). Also, the unit of measurement for FREECNT from
the documentation of all these devices is incorrect (taken from an older
generation). This was confirmed by Younes Leroul from Microchip support.
Not having anything better to do with these values at the moment* (this
will change soon), let's just print them.
*The frame buffer size is, in fact, used to calculate the tail dropping
watermarks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d8a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently ocelot_set_rx_mode calls ocelot_mact_learn directly, which has
a very nice ocelot_mact_wait_for_completion at the end. Introduced in
commit 639c1b2625af ("net: mscc: ocelot: Register poll timeout should be
wall time not attempts"), this function uses readx_poll_timeout which
triggers a lot of lockdep warnings and is also dangerous to use from
atomic context, potentially leading to lockups and panics.
Steen Hegelund added a poll timeout of 100 ms for checking the MAC
table, a duration which is clearly absurd to poll in atomic context.
So we need to defer the MAC table access to process context, which we do
via a dynamically allocated workqueue which contains all there is to
know about the MAC table operation it has to do.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212191612.222019-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current assumption is that the felix DSA driver has flooding knobs
per traffic class, while ocelot switchdev has a single flooding knob.
This was correct for felix VSC9959 and ocelot VSC7514, but with the
introduction of seville VSC9953, we see a switch driven by felix.c which
has a single flooding knob.
So it is clear that we must do what should have been done from the
beginning, which is not to overwrite the configuration done by ocelot.c
in felix, but instead to teach the common ocelot library about the
differences in our switches, and set up the flooding PGIDs centrally.
The effect that the bogus iteration through FELIX_NUM_TC has upon
seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and
ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will
actually overwrite ANA_FLOODING_IPMC when attempting to write
ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING.
And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect
is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D:
MC6_DATA = 61,
MC6_CTRL = 61,
MC4_DATA = 60,
MC4_CTRL = 0.
Because MC4_CTRL is zero, this means that IPv4 multicast control packets
are not flooded, but dropped. An invalid configuration, and this is how
the issue was actually spotted.
Reported-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Tested-by: Eldar Gasanov <eldargasanov2@gmail.com>
Fixes: 84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 3c7b51bd39b2 ("net: dsa: felix: allow flooding for all traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the ocelot_port_set_native_vlan() function starts dropping
untagged and prio-tagged traffic when the native VLAN is removed?
What is the native VLAN? It is the only egress-untagged VLAN that ocelot
supports on a port. If the port is a trunk with 100 VLANs, one of those
VLANs can be transmitted as egress-untagged, and that's the native VLAN.
Is it wrong to drop untagged and prio-tagged traffic if there's no
native VLAN? Yes and no.
In this case, which is more typical, it's ok to apply that drop
configuration:
$ bridge vlan add dev swp0 vid 1 pvid untagged <- this is the native VLAN
$ bridge vlan add dev swp0 vid 100
$ bridge vlan add dev swp0 vid 101
$ bridge vlan del dev swp0 vid 1 <- delete the native VLAN
But only because the pvid and the native VLAN have the same ID.
In this case, it isn't:
$ bridge vlan add dev swp0 vid 1 pvid
$ bridge vlan add dev swp0 vid 100 untagged <- this is the native VLAN
$ bridge vlan del dev swp0 vid 101
$ bridge vlan del dev swp0 vid 100 <- delete the native VLAN
It's wrong, because the switch will drop untagged and prio-tagged
traffic now, despite having a valid pvid of 1.
The confusion seems to stem from the fact that the native VLAN is an
egress setting, while the PVID is an ingress setting. It would be
correct to drop untagged and prio-tagged traffic only if there was no
pvid on the port. So let's do just that.
Background:
https://lore.kernel.org/netdev/CA+h21hrRMrLH-RjBGhEJSTZd6_QPRSd3RkVRQF-wNKkrgKcRSA@mail.gmail.com/#t
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we are checking in some places whether the port has a native
VLAN on egress or not, by comparing the ocelot_port->vid value with zero.
That works, because VID 0 can never be a native VLAN configured by the
bridge, but now we want to make similar checks for the pvid. That won't
work, because there are cases when we do have the pvid set to 0 (not by
the bridge, by ourselves, but still.. it's confusing). And we can't
encode a negative value into an u16, so add a bool to the structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
