9d75b88185
515 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Vladimir Oltean
|
9d75b88185 |
net: mscc: ocelot: annotate which traps need PTP timestamping
The ocelot switch library does not need this information, but the felix DSA driver does. As a reminder, the VSC9959 switch in LS1028A doesn't have an IRQ line for packet extraction, so to be notified that a PTP packet needs to be dequeued, it receives that packet also over Ethernet, by setting up a packet trap. The Felix driver needs to install special kinds of traps for packets in need of RX timestamps, such that the packets are replicated both over Ethernet and over the CPU port module. But the Ocelot switch library sets up more than one trap for PTP event messages; it also traps PTP general messages, MRP control messages etc. Those packets don't need PTP timestamps, so there's no reason for the Felix driver to send them to the CPU port module. By knowing which traps need PTP timestamps, the Felix driver can adjust the traps installed using ocelot_trap_add() such that only those will actually get delivered to the CPU port module. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
e42bd4ed09 |
net: mscc: ocelot: keep traps in a list
When using the ocelot-8021q tagging protocol, the CPU port isn't configured as an NPI port, but is a regular port. So a "trap to CPU" operation is actually a "redirect" operation. So DSA needs to set up the trapping action one way or another, depending on the tagging protocol in use. To ease DSA's work of modifying the action, keep all currently installed traps in a list, so that DSA can live-patch them when the tagging protocol changes. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
85ea0daabe |
net: mscc: ocelot: avoid overlap in VCAP IS2 between PTP and MRP traps
OCELOT_VCAP_IS2_TAG_8021Q_TXVLAN overlaps with OCELOT_VCAP_IS2_MRP_REDIRECT. To avoid this, make OCELOT_VCAP_IS2_MRP_REDIRECT take the cookie region from N to 2 * N - 1 (where N is ocelot->num_phys_ports). To avoid any risk that the singleton (not per port) VCAP IS2 filters overlap with per-port VCAP IS2 filters, we must ensure that the number of singleton filters is smaller than the number of physical ports. This is true right now, but may change in the future as switches with less ports get supported, or more singleton filters get added. So to be future-proof, let's move the singleton filters at the end of the range, where they won't overlap with anything to their right. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
b9bace6e53 |
net: mscc: ocelot: use a single VCAP filter for all MRP traps
The MRP assist code installs a VCAP IS2 trapping rule for each port, but since the key and the action is the same, just the ingress port mask differs, there isn't any need to do this. We can save some space in the TCAM by using a single filter and adjusting the ingress port mask. Reuse the ocelot_trap_add() and ocelot_trap_del() functions for this purpose. Now that the cookies are no longer per port, we need to change the allocation scheme such that MRP traps use a fixed number. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
36fac35b29 |
net: mscc: ocelot: delete OCELOT_MRP_CPUQ
MRP frames are configured to be trapped to the CPU queue 7, and this number is reflected in the extraction header. However, the information isn't used anywhere, so just leave MRP frames to go to CPU queue 0 unless needed otherwise. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
c518afec28 |
net: mscc: ocelot: consolidate cookie allocation for private VCAP rules
Every use case that needed VCAP filters (in order: DSA tag_8021q, MRP, PTP traps) has hardcoded filter identifiers that worked well enough for that use case alone. But when two or more of those use cases would be used together, some of those identifiers would overlap, leading to breakage. Add definitions for each cookie and centralize them in ocelot_vcap.h, such that the overlaps are more obvious. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Colin Foster
|
d87b1c08f3 |
net: mscc: ocelot: use bulk reads for stats
Create and utilize bulk regmap reads instead of single access for gathering stats. The background reading of statistics happens frequently, and over a few contiguous memory regions. High speed PCIe buses and MMIO access will probably see negligible performance increase. Lower speed buses like SPI and I2C could see significant performance increase, since the bus configuration and register access times account for a large percentage of data transfer time. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Colin Foster
|
40f3a5c815 |
net: mscc: ocelot: add ability to perform bulk reads
Regmap supports bulk register reads. Ocelot does not. This patch adds support for Ocelot to invoke bulk regmap reads. That will allow any driver that performs consecutive reads over memory regions to optimize that access. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Colin Foster
|
65c53595bc |
net: ocelot: align macros for consistency
In the ocelot.h file, several read / write macros were split across multiple lines, while others weren't. Split all macros that exceed the 80 character column width and match the style of the rest of the file. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Linus Torvalds
|
8efd0d9c31 |
Networking changes for 5.17.
Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible,
or at least perform the freeing outside of the socket lock section
to decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice
and net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported
in the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or
MSM8974 (qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch
driver with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of:
lan78xx, ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer granularity,
stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KLm3
-----END PGP SIGNATURE-----
Merge tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible, or at
least perform the freeing outside of the socket lock section to
decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice and
net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported in
the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or MSM8974
(qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch driver
with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of: lan78xx,
ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer
granularity, stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support"
* tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2048 commits)
tcp: tcp_send_challenge_ack delete useless param `skb`
net/qla3xxx: Remove useless DMA-32 fallback configuration
rocker: Remove useless DMA-32 fallback configuration
hinic: Remove useless DMA-32 fallback configuration
lan743x: Remove useless DMA-32 fallback configuration
net: enetc: Remove useless DMA-32 fallback configuration
cxgb4vf: Remove useless DMA-32 fallback configuration
cxgb4: Remove useless DMA-32 fallback configuration
cxgb3: Remove useless DMA-32 fallback configuration
bnx2x: Remove useless DMA-32 fallback configuration
et131x: Remove useless DMA-32 fallback configuration
be2net: Remove useless DMA-32 fallback configuration
vmxnet3: Remove useless DMA-32 fallback configuration
bna: Simplify DMA setting
net: alteon: Simplify DMA setting
myri10ge: Simplify DMA setting
qlcnic: Simplify DMA setting
net: allwinner: Fix print format
page_pool: remove spinlock in page_pool_refill_alloc_cache()
amt: fix wrong return type of amt_send_membership_update()
...
|
||
|
Linus Torvalds
|
e85195d5bf |
ARM: SoC driver updates for v5.17
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
|
||
|
Vladimir Oltean
|
5cad43a52e |
net: dsa: felix: add port fast age support
Add support for flushing the MAC table on a given port in the ocelot switch library, and use this functionality in the felix DSA driver. This operation is needed when a port leaves a bridge to become standalone, and when the learning is disabled, and when the STP state changes to a state where no FDB entry should be present. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Dmitry Osipenko
|
9131c63317 |
soc/tegra: Add devm_tegra_core_dev_init_opp_table_common()
Only couple drivers need to get the -ENODEV error code and majority of drivers need to explicitly initialize the performance state. Add new common helper which sets up OPP table for these drivers. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> |
||
Clément Léger
|
753a026cfe |
net: ocelot: add FDMA support
Ethernet frames can be extracted or injected autonomously to or from the device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list data structures in memory are used for injecting or extracting Ethernet frames. The FDMA generates interrupts when frame extraction or injection is done and when the linked lists need updating. The FDMA is shared between all the ethernet ports of the switch and uses a linked list of descriptors (DCB) to inject and extract packets. Before adding descriptors, the FDMA channels must be stopped. It would be inefficient to do that each time a descriptor would be added so the channels are restarted only once they stopped. Both channels uses ring-like structure to feed the DCBs to the FDMA. head and tail are never touched by hardware and are completely handled by the driver. On top of that, page recycling has been added and is mostly taken from gianfar driver. Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Co-developed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Clément Léger
|
b471a71e52 |
net: ocelot: add and export ocelot_ptp_rx_timestamp()
In order to support PTP in FDMA, PTP handling code is needed. Since this is the same as for register-based extraction, export it with a new ocelot_ptp_rx_timestamp() function. Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Clément Léger
|
e5150f0072 |
net: ocelot: export ocelot_ifh_port_set() to setup IFH
FDMA will need this code to prepare the injection frame header when sending SKBs. Move this code into ocelot_ifh_port_set() and add conditional IFH setting for vlan and rew op if they are not set. Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Colin Foster
|
840ece19e9 |
net: ocelot: fix missed include in the vsc7514_regs.h file
commit |
||
|
Colin Foster
|
32ecd22ba6 |
net: mscc: ocelot: split register definitions to a separate file
Move these to a separate file will allow them to be shared to other drivers. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Jakub Kicinski
|
93d5404e89 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
drivers/net/ipa/ipa_main.c |
||
|
Vladimir Oltean
|
95706be13b |
net: mscc: ocelot: create a function that replaces an existing VCAP filter
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind tc flower offload on ocelot, among other things. The ingress port mask on which VCAP rules match is present as a bit field in the actual key of the rule. This means that it is possible for a rule to be shared among multiple source ports. When the rule is added one by one on each desired port, that the ingress port mask of the key must be edited and rewritten to hardware. But the API in ocelot_vcap.c does not allow for this. For one thing, ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric, because ocelot_vcap_filter_add() works with a preallocated and prepopulated filter and programs it to hardware, and ocelot_vcap_filter_del() does both the job of removing the specified filter from hardware, as well as kfreeing it. That is to say, the only option of editing a filter in place, which is to delete it, modify the structure and add it back, does not work because it results in use-after-free. This patch introduces ocelot_vcap_filter_replace, which trivially reprograms a VCAP entry to hardware, at the exact same index at which it existed before, without modifying any list or allocating any memory. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Vladimir Oltean
|
8abe197038 |
net: dsa: felix: enable cut-through forwarding between ports by default
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
||
Xiaoliang Yang
|
a7e13edf37 |
net: dsa: felix: restrict psfp rules on ingress port
PSFP rules take effect on the streams from any port of VSC9959 switch. This patch use ingress port to limit the rule only active on this port. Each stream can only match two ingress source ports in VSC9959. Streams from lowest port gets the configuration of SFID pointed by MAC Table lookup and streams from highest port gets the configuration of (SFID+1) pointed by MAC Table lookup. This patch defines the PSFP rule on highest port as dummy rule, which means that it does not modify the MAC table. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xiaoliang Yang
|
77043c3709 |
net: mscc: ocelot: use index to set vcap policer
Policer was previously automatically assigned from the highest index to the lowest index from policer pool. But police action of tc flower now uses index to set an police entry. This patch uses the police index to set vcap policers, so that one policer can be shared by multiple rules. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xiaoliang Yang
|
7d4b564d6a |
net: dsa: felix: support psfp filter on vsc9959
VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies with the IEEE 802.1Qci standard. The stream is identified by Null stream identification(DMAC and VLAN ID) defined in IEEE802.1CB. For PSFP, four tables need to be set up: stream table, stream filter table, stream gate table, and flow meter table. Identify the stream by parsing the tc flower keys and add it to the stream table. The stream filter table is automatically maintained, and its index is determined by SGID(flow gate index) and FMID(flow meter index). Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xiaoliang Yang
|
23e2c506ad |
net: mscc: ocelot: add gate and police action offload to PSFP
PSFP support gate and police action. This patch add the gate and police action to flower parse action, check chain ID to determine which block to offload. Adding psfp callback functions to add, delete and update gate and police in PSFP table if hardware supports it. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xiaoliang Yang
|
0568c3bf3f |
net: mscc: ocelot: add MAC table stream learn and lookup operations
ocelot_mact_learn_streamdata() can be used in VSC9959 to overwrite an
FDB entry with stream data. The stream data includes SFID and SSID which
can be used for PSFP and FRER set.
ocelot_mact_lookup() can be used to check if the given {DMAC, VID} FDB
entry is exist, and also can retrieve the DEST_IDX and entry type for
the FDB entry.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Linus Torvalds
|
d461e96cd2 |
ARM: SoC drivers for 5.16
These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----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=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
|
||
|
Linus Torvalds
|
fc02cb2b37 |
Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
|
||
|
Linus Torvalds
|
57a315cd71 |
Time, timers and timekeeping updates:
- No core updates
- No new clocksource/event driver
- A large rework of the ARM architected timer driver to prepare for the
support of the upcoming ARMv8.6 support
- Fix Kconfig options for Exynos MCT, Samsung PWM and TI DM timers
- Address a namespace collison in the ARC sp804 timer driver
-----BEGIN PGP SIGNATURE-----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=SVx3
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and timekeeping updates:
- No core updates
- No new clocksource/event driver
- A large rework of the ARM architected timer driver to prepare for
the support of the upcoming ARMv8.6 support
- Fix Kconfig options for Exynos MCT, Samsung PWM and TI DM timers
- Address a namespace collison in the ARC sp804 timer driver"
* tag 'timers-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Select TIMER_OF
clocksource/drivers/exynosy: Depend on sub-architecture for Exynos MCT and Samsung PWM
clocksource/drivers/arch_arm_timer: Move workaround synchronisation around
clocksource/drivers/arm_arch_timer: Fix masking for high freq counters
clocksource/drivers/arm_arch_timer: Drop unnecessary ISB on CVAL programming
clocksource/drivers/arm_arch_timer: Remove any trace of the TVAL programming interface
clocksource/drivers/arm_arch_timer: Work around broken CVAL implementations
clocksource/drivers/arm_arch_timer: Advertise 56bit timer to the core code
clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL
clocksource/drivers/arm_arch_timer: Fix MMIO base address vs callback ordering issue
clocksource/drivers/arm_arch_timer: Move drop _tval from erratum function names
clocksource/drivers/arm_arch_timer: Move system register timer programming over to CVAL
clocksource/drivers/arm_arch_timer: Extend write side of timer register accessors to u64
clocksource/drivers/arm_arch_timer: Drop CNT*_TVAL read accessors
clocksource/arm_arch_timer: Add build-time guards for unhandled register accesses
clocksource/drivers/arc_timer: Eliminate redefined macro error
|
||
|
Vladimir Oltean
|
2468346c56 |
net: mscc: ocelot: serialize access to the MAC table
DSA would like to remove the rtnl_lock from its
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses
the same MAC table functions as ocelot.
This means that the MAC table functions will no longer be implicitly
serialized with respect to each other by the rtnl_mutex, we need to add
a dedicated lock in ocelot for the non-atomic operations of selecting a
MAC table row, reading/writing what we want and polling for completion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
David S. Miller
|
2d7e73f09f |
Revert "Merge branch 'dsa-rtnl'"
This reverts commit |
||
|
Vladimir Oltean
|
f2c4bdf62d |
net: mscc: ocelot: serialize access to the MAC table
DSA would like to remove the rtnl_lock from its
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses
the same MAC table functions as ocelot.
This means that the MAC table functions will no longer be implicitly
serialized with respect to each other by the rtnl_mutex, we need to add
a dedicated lock in ocelot for the non-atomic operations of selecting a
MAC table row, reading/writing what we want and polling for completion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
d4004422f6 |
net: mscc: ocelot: track the port pvid using a pointer
Now that we have a list of struct ocelot_bridge_vlan entries, we can rewrite the pvid logic to simply point to one of those structures, instead of having a separate structure with a "bool valid". The NULL pointer will represent the lack of a bridge pvid (not to be confused with the lack of a hardware pvid on the port, that is present at all times). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
0da1a1c489 |
net: mscc: ocelot: allow a config where all bridge VLANs are egress-untagged
At present, the ocelot driver accepts a single egress-untagged bridge
VLAN, meaning that this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan add dev swp0 vid 2 pvid untagged
fails because the bridge automatically installs VID 1 as a pvid & untagged
VLAN, and vid 2 would be the second untagged VLAN on this port. It is
necessary to delete VID 1 before proceeding to add VID 2.
This limitation comes from the fact that we operate the port tag, when
it has an egress-untagged VID, in the OCELOT_PORT_TAG_NATIVE mode.
The ocelot switches do not have full flexibility and can either have one
single VID as egress-untagged, or all of them.
There are use cases for having all VLANs as egress-untagged as well, and
this patch adds support for that.
The change rewrites ocelot_port_set_native_vlan() into a more generic
ocelot_port_manage_port_tag() function. Because the software bridge's
state, transmitted to us via switchdev, can become very complex, we
don't attempt to track all possible state transitions, but instead take
a more declarative approach and just make ocelot_port_manage_port_tag()
figure out which more to operate in:
- port is VLAN-unaware: the classified VLAN (internal, unrelated to the
802.1Q header) is not inserted into packets on egress
- port is VLAN-aware:
- port has tagged VLANs:
-> port has no untagged VLAN: set up as pure trunk
-> port has one untagged VLAN: set up as trunk port + native VLAN
-> port has more than one untagged VLAN: this is an invalid config
which is rejected by ocelot_vlan_prepare
- port has no tagged VLANs
-> set up as pure egress-untagged port
We don't keep the number of tagged and untagged VLANs, we just count the
structures we keep.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
90e0aa8d10 |
net: mscc: ocelot: convert the VLAN masks to a list
First and foremost, the driver currently allocates a constant sized 4K * u32 (16KB memory) array for the VLAN masks. However, a typical application might not need so many VLANs, so if we dynamically allocate the memory as needed, we might actually save some space. Secondly, we'll need to keep more advanced bookkeeping of the VLANs we have, notably we'll have to check how many untagged and how many tagged VLANs we have. This will have to stay in a structure, and allocating another 16 KB array for that is again a bit too much. So refactor the bridge VLANs in a linked list of structures. The hook points inside the driver are ocelot_vlan_member_add() and ocelot_vlan_member_del(), which previously used to operate on the ocelot->vlan_mask[vid] array element. ocelot_vlan_member_add() and ocelot_vlan_member_del() used to call ocelot_vlan_member_set() to commit to the ocelot->vlan_mask. Additionally, we had two calls to ocelot_vlan_member_set() from outside those callers, and those were directly from ocelot_vlan_init(). Those calls do not set up bridging service VLANs, instead they: - clear the VLAN table on reset - set the port pvid to the value used by this driver for VLAN-unaware standalone port operation (VID 0) So now, when we have a structure which represents actual bridge VLANs, VID 0 doesn't belong in that structure, since it is not part of the bridging layer. So delete the middle man, ocelot_vlan_member_set(), and let ocelot_vlan_init() call directly ocelot_vlant_set_mask() which forgoes any data structure and writes directly to hardware, which is all that we need. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
62a22bcbd3 |
net: mscc: ocelot: add a type definition for REW_TAG_CFG_TAG_CFG
This is a cosmetic patch which clarifies what are the port tagging options for Ocelot switches. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Randy Dunlap
|
58100c34f7 |
clocksource/drivers/arc_timer: Eliminate redefined macro error
In drivers/clocksource/, 3 drivers use "TIMER_CTRL_IE" with 3 different
values. Two of them (mps2-timer.c and timer-sp804.c/timer-sp.h) are
localized and left unmodifed.
One of them uses a shared header file (<soc/arc/timers.h>), which is
what is causing the "redefined" warnings, so change the macro name in
that driver only. Also change the TIMER_CTRL_NH macro name.
Both macro names are prefixed with "ARC_" to reduce the likelihood
of future name collisions.
In file included from ../drivers/clocksource/timer-sp804.c:24:
../drivers/clocksource/timer-sp.h:25: error: "TIMER_CTRL_IE" redefined [-Werror]
25 | #define TIMER_CTRL_IE (1 << 5) /* VR */
../include/soc/arc/timers.h:20: note: this is the location of the previous definition
20 | #define TIMER_CTRL_IE (1 << 0) /* Interrupt when Count reaches limit */
Fixes:
|
||
Ioana Ciornei
|
69651bd8d3 |
soc: fsl: dpio: add Net DIM integration
Use the generic dynamic interrupt moderation (dim) framework to implement adaptive interrupt coalescing on Rx. With the per-packet interrupt scheme, a high interrupt rate has been noted for moderate traffic flows leading to high CPU utilization. The dpio driver exports new functions to enable/disable adaptive IRQ coalescing on a DPIO object, to query the state or to update Net DIM with a new set of bytes and frames dequeued. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Ioana Ciornei
|
ed1d2143fe |
soc: fsl: dpio: add support for irq coalescing per software portal
In DPAA2 based SoCs, the IRQ coalesing support per software portal has 2 configurable parameters: - the IRQ timeout period (QBMAN_CINH_SWP_ITPR): how many 256 QBMAN cycles need to pass until a dequeue interrupt is asserted. - the IRQ threshold (QBMAN_CINH_SWP_DQRR_ITR): how many dequeue responses in the DQRR ring would generate an IRQ. Add support for setting up and querying these IRQ coalescing related parameters. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Ioana Ciornei
|
2cf0b6fe9b |
soc: fsl: dpio: extract the QBMAN clock frequency from the attributes
Through the dpio_get_attributes() firmware call the dpio driver has access to the QBMAN clock frequency. Extend the structure which holds the firmware's response so that we can have access to this information. This will be needed in the next patches which also add support for interrupt coalescing which needs to be configured based on the frequency. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Jakub Kicinski
|
e15f5972b8 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
tools/testing/selftests/net/ioam6.sh |
||
Arnd Bergmann
|
936fc53f3d |
Qualcomm driver updates for v5.16
This drops the use of power-domains for exposing the load_state from the QMP driver to clients, to avoid issues related to system suspend. SMP2P becomes wakeup capable, to allow dying remoteprocs to wake up Linux from suspend to perform recovery. It adds RPM power-domain support for SM6350 and MSM8953 and base RPM support for MSM8953 and QCM2290. It adds support for MSM8996, SDM630 and SDM660 in the SPM driver, which will enable the introduction of proper voltage scaling of the CPU subsystem. Support for releasing secondary CPUs on MSM8226 is introduced. The Asynchronous Packet Router (APR) driver is extended to support the new Generic Packet Router (GPR) variant, which is used to communicate with the firmware in the new AudioReach audio driver. Lastly it transitions a number of drivers to safer string functions, as well as switching things to use devm_platform_ioremap_resource(). -----BEGIN PGP SIGNATURE----- iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAmFlxugbHGJqb3JuLmFu ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3F3A0P/ixLiu0XktPOyFZ+3Ag/ 5KKan6wlH8JO0AfxbOolk0MkC1/8uk1V+Kuw4b/22jTO4w/9Illi9jSmV0wR3IBh 26sWpyxNK7N+7uAnBDqlZekQYTg5xKqJGn69kxe0oIm8yAogGkxZnlIWt7JGtWS0 NcyLLe9gS/B/q6ppTkxlYhSMB3Qp6bU/lRjBWTcHlxaNxGyNbGw4zp5ncze8ui9R s0JdFhJ/T1ptuWuIhrEWXEVapQtf0pgPvYSWxRYoBRU4N1F4HcRcLVpUU6eSvFEg BKxN11dCW4o0njLBpdPtg3u7AL31A95OPFiVwpWEb6Wov1DAdQYfYSoc7r2uqKvL QgvE/Fq1uPNPsFH2AgJjmku7nb2S0UP2msIhsZjugwxCQXtHgv2uPdYSN/MOudEZ MdjbbAHKW9+TR4gTVzA7b7OVzB73+tjHo/4hUjy8J5RlRKujbzHHXLRjvpNAILqn y457eUFqYxR1C3CKy2GrgR/PvNcBdDVq0ikuv4elYZEIaPL/Wxg6V7RJSHzgAgU/ 7XArrGvCXdLXy/e07KJ4Su74OBOsXnqLLr+Xsw5+h42XCnDfmI3caQlQjTXxJxN4 EifHOoPCa8JNtXzWKSBSO7Pb5teSYh5XlAQs8nGVbrKMhly/MDLeNzSL+uu8DGNw B9Cf/mM9bhs3Q69Z37WgOdK0 =FE4j -----END PGP SIGNATURE----- gpgsig -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFnQuMACgkQmmx57+YA GNk90g/9F5Sh8wfMQ3WYZMu10L431dXYKkafccK8SFgNhTxTuJ7xPbJzXxFQW6Qp Ky0DAKcJB/tW/jCMh7L/d7pET4tedRncZd6Pk8kkn8uRC9qiTEFyPKP+4trADnhw Q/gf8xbEJz13aDzFbfW2Ko9Rx0HJQ/BSWVzZ5fpkUmoSSBnxm+rq9T3e10BNX1QT /Bg1M77zyYWtlPKexjxBEz7EZuQIEmN9gkCCriYTMw34hfVYszsNkIZnIGfe/wAa F6iSjIwVqf4DbM6QzabNoCUzZf50Ij4Vdlhvk5FUt3quPIvcULzIxQxI3o/J5sJ2 2mowPuiVjmqx4R8XFILod0+KU4NNUGcb2YFLZg+XjbopArfLZaa2OV40m2QDY/Ay /BHXBtxLDDcDqwOX6Y7NEfbNFUqLlFv00vuZEJ9KT/19ZfJgCw4qoxw44aldjQEo 3pvEACOHLKoI+FOeb6LHL0erfc1jz/qul37oWI361rDIfWsWsZtbyc+gItMDLGYa C1qUHoP5vMmse0tILT6AJNR23aGJFapKkzTNWB6j5Pi/0sdv3zGbhxubf+TxMRtx 5BhEP2N5pHdKVopxVSG2JVOtT12jE68tV0E00erEoPIG35C+DyADn5i9lg4g20Ix MwxwtgAC0cws8tpwsDvFOCj8SPn9HDtEGMJMejo5xuEIxqjAb2E= =LLU7 -----END PGP SIGNATURE----- Merge tag 'qcom-drivers-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers Qualcomm driver updates for v5.16 This drops the use of power-domains for exposing the load_state from the QMP driver to clients, to avoid issues related to system suspend. SMP2P becomes wakeup capable, to allow dying remoteprocs to wake up Linux from suspend to perform recovery. It adds RPM power-domain support for SM6350 and MSM8953 and base RPM support for MSM8953 and QCM2290. It adds support for MSM8996, SDM630 and SDM660 in the SPM driver, which will enable the introduction of proper voltage scaling of the CPU subsystem. Support for releasing secondary CPUs on MSM8226 is introduced. The Asynchronous Packet Router (APR) driver is extended to support the new Generic Packet Router (GPR) variant, which is used to communicate with the firmware in the new AudioReach audio driver. Lastly it transitions a number of drivers to safer string functions, as well as switching things to use devm_platform_ioremap_resource(). * tag 'qcom-drivers-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (40 commits) soc: qcom: apr: Add GPR support soc: dt-bindings: qcom: add gpr bindings soc: qcom: apr: make code more reuseable soc: dt-bindings: qcom: apr: deprecate qcom,apr-domain property soc: dt-bindings: qcom: apr: convert to yaml dt-bindings: soc: qcom: aoss: Delete unused power-domain definitions dt-bindings: msm/dp: Remove aoss-qmp header soc: qcom: aoss: Drop power domain support dt-bindings: soc: qcom: aoss: Drop the load state power-domain soc: qcom: smp2p: Add wakeup capability to SMP2P IRQ dt-bindings: power: rpmpd: Add SM6350 to rpmpd binding dt-bindings: soc: qcom: aoss: Add SM6350 compatible soc: qcom: llcc: Disable MMUHWT retention soc: qcom: smd-rpm: Add QCM2290 compatible dt-bindings: soc: qcom: smd-rpm: Add QCM2290 compatible firmware: qcom_scm: Add compatible for MSM8953 SoC dt-bindings: firmware: qcom-scm: Document msm8953 bindings soc: qcom: pdr: Prefer strscpy over strcpy soc: qcom: rpmh-rsc: Make use of the helper function devm_platform_ioremap_resource_byname() soc: qcom: gsbi: Make use of the helper function devm_platform_ioremap_resource() ... Link: https://lore.kernel.org/r/20211012173442.1017010-1-bjorn.andersson@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> |
||
|
Vladimir Oltean
|
49f885b2d9 |
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes:
|
||
|
Vladimir Oltean
|
deab6b1cd9 |
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
As explained here: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/ DSA tagging protocol drivers cannot depend on symbols exported by switch drivers, because this creates a circular dependency that breaks module autoloading. The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function exported by the common ocelot switch lib. This function looks at OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the DSA tag, for PTP timestamping (the command: one-step/two-step, and the TX timestamp identifier). None of that requires deep insight into the driver, it is quite stateless, as it only depends upon the skb->cb. So let's make it a static inline function and put it in include/linux/dsa/ocelot.h, a file that despite its name is used by the ocelot switch driver for populating the injection header too - since commit |
||
|
Vladimir Oltean
|
ebb4c6a990 |
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes:
|
||
|
Vladimir Oltean
|
52849bcf00 |
net: mscc: ocelot: avoid overflowing the PTP timestamp FIFO
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes:
|
||
|
Vladimir Oltean
|
c57fe0037a |
net: mscc: ocelot: make use of all 63 PTP timestamp identifiers
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.
The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.
The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.
The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.
Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.
Fixes:
|
||
|
Jakub Kicinski
|
9fe1155233 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Dmitry Osipenko
|
0d7281b27a |
soc/tegra: pm: Make stubs usable for compile testing
The PM stubs need to depend on ARCH_TEGRA in order to be usable for compile-testing of tegra-cpuidle driver. Add the dependency. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> |
||
|
Dmitry Osipenko
|
aa54686e28 |
soc/tegra: irq: Add stubs needed for compile testing
Add stubs needed for compile-testing of tegra-cpuidle driver. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> |